Search Documents

By J Webb

Anoxic limestone drains (ALDs) have been widely used in the passive treatment of acid mine drainage (AMD), but their effectiveness has often been less than anticipated. Iron hydroxide often precipitates around limestone particles and inhibits neutralisation. To determine the conditions under which iron hydroxide precipitates, a small-scale laboratory ALD system was built to enable a detailed examination of the chemistry of iron within the drain. For one experiment, a mixture of limestone and quartz was introduced to the drain to assist in the determination of the key mechanism governing iron precipitation. Synthetic anaerobic acid mine drainage containing Fe2+ (~130 ppm), SO4 2- and H+ was pumped at a rate of 30 mL/min up a 90 cm tall, 15 cm diameter vertical column filled with limestone gravel of 98 per cent purity. Three sampling ports were fitted at equal intervals along the column; water was periodically extracted for analysis at the sampling ports over an 11-hour period. Experiments were run at influent pH levels of 2 and 4. Results show that acid neutralisation to pH greater than 6 occurred at the inflow end of the drain. The greatest amount of iron precipitation (19.5 per cent) also occurred in this area. The lack of iron precipitation on the quartz surfaces in the quartz/limestone mixture indicates that neutralisation is the key mechanism for the precipitation of iron hydroxide on limestone particles. A pe-pH stability diagram derived for the laboratory ALD system indicates that ALDs will not be effective for AMD with pH 2. Influent waters with pH 2 require a pe of -2 (Eh: -118.4 mV) to avoid Fe precipitation upon neutralisation. Influent waters of pH 4 require a pe between -2 and -4.

Jan 1, 2003

Autogenous and Semi-Autogenous grinding has become an accepted method of reducing primary crusher product to micron sizes in a single or a two-stage grinding circuit. The elimination of secondary and tertiary crusher circuits and sometimes rod mills helps to lower overall operating costs and, in many instances, can make uneconomical projects viable. Selecting AG/SAG Mills have been rather a "hit and miss" affair over the years, but now with the many different types of tests available, accurate mill size predictions can be made, provided the test data is evaluated correctly. This paper endeavours to simplify the process of evaluating test data and sets down some guidelines for designers to follow when selecting AG/SAG Mills.

Jan 1, 1991

Forty years ago Dr Pierre M Gy, a metallurgist, introduced variography as applied to monitoring a process. Consequently, his followers used the variogram to elaborate meaningful process control charts, especially since 1993. The name æChronostatisticsÆ was suggested several times by Gy as a logical name for this new science. The intent was to draw a parallel between the variogram identifying the variability components affecting a process parameter as a function of time, and the variogram used in geostatistics identifying the variability components of a given mineral content as a function of space. Heterogeneity problems encountered have indeed strong similarities. However, there is a fundamental difference. The variogram used in geostatistics is often stationary within a given type of mineralisation. While investigating a dynamic process through Chronostatistics, there is no such thing as a stationary variogram. Still, the evolving variogram provides essential information about subtle, often overlooked process difficulties. Chronostatistics is especially useful for management to take advantage of existing data that are often a forgotten source of valuable information to pinpoint recurring structural problems. The superiority of Chronostatistics over conventional statistical process control approaches is that it links observations to the inherent heterogeneity of materials under investigation, therefore to the sampling theory. Chronostatistics is like opening a new world to the metallurgist, making the process variability speak in a more comprehensive and in-depth way. Several case studies are presented to demonstrate the potency of this new science. For each of them, observations lead to solutions for continuous process improvement, therefore attractive economic opportunities. The philosophy is this: if a control chart shows a process is out of control, it must also suggest logical and pragmatic directions for solutions. The intent of this presentation is to vastly expand on these valuable, almost forgotten ideas.

Jan 1, 2006

By A Specht, A Müller, V Montenegro, S Winkler, E Klaffenbach, A Schmidt

In the process of primary copper smelting in flash smelting furnace (FSF), the ratio of iron to silica (Fe/SiO2 mass ratio) primarily determines the slag viscosity and magnetite formation. Viscous slag does not only cause difficulties in daily operation, such as in tapping, it also increases the copper losses to slag. Thus, keeping the Fe/SiO2 mass ratio at the desired level is an important aspect of FSF and slag cleaning furnace (SCF) operation. In this study, the improvement of the Fe/SiO2 mass ratio was conducted in two steps: First, the optimal Fe/SiO2 mass ratio was derived based on thermodynamic data. Based on this analysis, appropriate control limits were determined. Second, this range of favourable Fe/SiO2 mass ratios was implemented into operation by an advice-based control system, which suggests the addition of silica based on the analysis of SCF slag. As this approach was successful, the same advice-based control system principle was adapted for the coke addition to the SCF. After testing the new advice-based control for several months, the production data confirm the predictions by thermodynamics: since the prediction was implemented as an advisor, the copper and magnetite content in SCF slag is significantly reduced and viscous slag is reported less often by operations.

Aug 21, 2024

By Parrington PJ, Bailey A

Serious exploration for carbonate-hosted lead/zinc deposits in the Pillara district commenced in 1971 when Trend Exploration acquired exploration tenements covering stream sediment anomalies in the Limestone Billy Hills area. Shell Minerals managed the project from 1974 to 1976, and BHP Minerals Limited assumed management during 1976. Carbonate-hosted 'Mississippi-Valley- type' Pb-Zn deposits most commonly occur in Palaeozoic shallow marine carbonate complexes. At Pillara upper Devonian (Givetian/Frasnian) reef complexes are preserved on the flanks of Precambrian basement 'highs'. Within platform and atoll facies limestones sphalerite-galena- marcasite-calcite mineralisation occurs as disseminations, veins and breccia matrix, mostly associated with fractures and fault zones. Early exploration concentrated on detailed surface geochemistry and IP geophysical surveys, with geological mapping and shallow target percussion and diamond drilling. Results were discouraging and did not indicate potential for a shallow base metal resource. During 1976-77 BHP adopted a grid diamond drilling exploration technique and commenced testing an area of approximately 50 sq. km, initially using an 800 m square grid. In 1978 high grade mineralisation was intersected in an area subsequently named Blendevale. This was in the seventh diamond drill hole in the 800 m grid drilling programme, and to date more than 400 holes have been cored in the Pillara area. Detailed drilling at Blendevale has defined a number of mineralised breccia zones within an area of 2.4 km x 0.5 km, at depths of 100 m to 600 m below surface. The breccia bodies are associated with a series of north-south trending normal fault zones, forming a graben structure. The mineralisation occurs as breccia matrix surrounding unaltered limestone clasts, as veins filling steep fracture zones, and as

Jan 1, 1986

By J G. Webster-Brown

The Tui Mine is located near Te Aroha at the base of the Coromandel Peninsula. It was a lead-zinc mine, which closed in 1973 due to declining concentrate prices, high overheads, and high mercury levels in the ore. The site was abandoned, leaving behind an acid rock drainage generating system, including a sulfide-rich tailings dam which has since caused pollution of Tui Stream, as well as open adits and waste piles which drain predominantly into the neighbouring Tunakohoia Stream. At the AusIMM conference in 2003, Harvey and Webster-Brown presented water quality results from the Tui mine site and lower stream catchments in 2002. In April 2006, Environment Waikato undertook remediation works to stabilise the dam and reduce acid drainage entering Tui Stream. In this study, water quality results from the Tui mine site and lower stream catchments are again being determined, in order to compare with the pre-remediation results. Preliminary data collected for summer indicate a minor but consistent improvement in water quality in the lower stream catchments, although lower Tui Stream continues to exceed ANZECC (2000) aquatic life guidelines for Cd, Cu, Pb and Zn. This slight improvement may be due to a decrease in the flow of ARD into Tui Stream, as there does not appear to have been an improvement in quality of the contributing ARD waters.

Jan 1, 2007

By W Malone, J Garrett

FLSmidth (FLS) has spent the last 15 years, working with customers and engineering houses to deliver innovative improvements in crusher safety, coupled with the latest, maintenance friendly, crusher design. The key focus being to prevent service personnel from working underneath the crusher during maintenance and obviate the need for personnel to be exposed to suspended loads when performing tasks such as, main shaft installation, for example. Improvements include: full top-service capability to ensure the safest and fastest way to disassemble the crusher for maintenance purposes, which also removes the requirement for a service cart; a selfaligning main shaft which ensures remote assembly is now possible, keeping service personnel well out of harm’s way; And rotable shells, or the ability to perform relines off-station, allows for quick shell ‘swap-over’ without the downtime associated with removing, refitting and curing time associated with epoxy backing. The high flow spider improves large material entry into the crusher, reducing blockages and downtime and therefore maintains crusher capacity. Each size of crusher in the range comes with an option to increase the standard feed opening to a larger one if desired to compensate for ‘blocky’ or ‘elongated’ feed material, a common problem for Pilbara hematite iron ores. Power capability has also been increased with a maximum of 1500 kW, to match the higher throughput capacities being achieved. This due to uprated eccentric speeds and larger discharge annulus. Increased eccentric throws and mantle diameters are also now a reality, when compared to more traditional designed gyratory crushers. To keep up with the improved design features of the Mk V, digitalisation has also been upgraded to maximise performance capabilities to ensure that the most efficient reduction and throughput capacities are achieved, whilst utilising the higher powers now available as standard. Condition monitoring ensures that the crusher is at its optimum operating capability by monitoring and adjusting the crusher settings via feedback from additional sensors, ie main shaft spin, temperature and vibration. Camera monitoring capabilities are available as is an advanced oil contamination monitoring system. As a result of the above design improvements, it will be shown that the Mk V range offers benefits such as: enhanced safety features, increased availability, faster maintenance turnarounds, higher power utilisation, equivalent product size at higher throughput capacities and with Remote operation capabilities. All of which result in a gyratory crusher with higher levels of safety and a lower per tonne operating cost.

Sep 18, 2023

By Sans H

The geostatistical Discrete Gaussian (DG) model is demonstrated to be capable of providing an effective means of implementing change of support for Enterprise-style mineralisation and thus providing reliable global recoverable resource estimates. At Enterprise, sample grade distribution proves to be highly positively skewed, therefore significant deskewing of the histogram and reduction of variance occurs when going from sample to block support. The DG model was experimentally tested in'the Southern Primary Zone (SPZ) at Enterprise, where high anisotropy ratios and pronounced short range structures are observed in variograms. The experimental test was run for a change of support for which the variance reduction was. approximately 60 per cent. This reduction is similar to that predicted by Krige's Relationship ('the volume-variance relationship') for the practical situation of a change of support from 5 m vertical blasthole samples to 3 m x 8 m x 5 m selective mining unit (SMU) blocks. The DG model was found to correctly predict the grade tonnage relationships for a wide range of cut off grades. The experimental test indicated that, given a representative histogram and variogram, the DG change of support provides a computationally efficient and practical means of reliably assessing global mineable resources at the early stages of a mining project. Further, it allows a range of selectivity strategies to be meaningfully and comparatively considered prior to mining.

Jan 1, 1995

By Savage E. N

The porphyry copper minerals of Melanesia occur within a host of narrow veinlets in predominantly quartz diorite stocks or as contact metasomatic masses in skarns adjacent to the intrusion. Some 90 per cent of the constituent minerals comprise pyrite or marcasite, chalcopyrite, and magnetite with the remainder mainly bornite and hematite with accessory rutile and chalcocite together with several trace minerals. Gold is found mainly as inclusions in chalcopyrite, and minor molybdenite occurs likewise.Of particular significance is the persistent occurrence of accessory rutile of hydrothermal origin intimately intergrown with chalcopyrite. The rutile occurs relatively late in the hydrothermal sequence and upon weathering of the deposit may be released on a cumulative basis possibly in sufficient amounts to constitute a particulate pathfinder mineral which may aid in prospecting.Rutile is present in all the Melanesian occurrences studied and is also prominent in several American deposits.The porphyry copper mineralogy is characterized by the presence of accessory hydrothermal rutile intergrown with chalcopyrite.

Jan 1, 1975

This study is to compare reinforcement of rebar and spiral bolts using laboratory pull-out test. For this purpose, the pull-out test was performed in laboratory for a curing period of 7- and 28-days. Based on the results of the laboratory pull-out test, the pull-out load of two support members rapidly increased with displacement until the breakpoint and then gently increased with displacement. The maximum pull-out load of spiral bolt was larger than that of rebar bolt. This implies that a spiral bolt is more stable than a rebar bolt for securing the stability of a ground or rock mass when a support was installed in a ground or rock mass under the same condition. In addition, the maximum external pressure of two support members increased with pull-out load and with displacement and the distribution of external pressure was commonly larger at the upper part than at the lower part of specimen. This indicates that the bond failure location by pull-out load should be mainly occurred at the surface portion of specimen. In conclusion, the reinforcing effect of a support depends on a curing period and a type of support member, and reinforcement of a spiral bolt is more effective than that of a rebar bolt.

Dec 6, 2010

By Hinde J. S

The Fitzpatrick Orebody is a three and a half million tonne fault bounded portion of the early-middle Proterozoic Broken Hill Orebody.The Fitzpatrick Orebody was discovered in 1975 by diamond drilling from the 36 Level Exploratory Drive. This followed persistent geologically oriented exploration and a courageous decision by mine management to deepen No. 3 Shaft to provide exploratory development across the Globe Vauxhall Shear and allow effective drilling of the target area.The stratiforrn oebody consists of three lenses, the lead rich No. 2 and 3 Lenses and smaller zinc lode. They represent a down plunge extension and boudinaged, fault-bounded portion of the main Broken Hill ore lenses. The surrounding host rocks are extensively faulted and jointed due to complex history of movement on the bounding shears. This results in extremely poor ground conditions during mining. The ore was delineated for mining development using three dimensional fan drilling from exploratory and hanging wall drive drill sites.

Jan 1, 1990

By K McSweeney, A Marton

This paper discusses the development of a strategy for ensuring long-term geotechnical stability of final pit walls at AngloGold AustraliaÆs Sunrise Dam Gold Mine. The strategy makes use of improved blasting techniques, changes to the mining sequence and other geotechnical techniques. Only the blasting techniques will be discussed in this paper. These were developed from numerous trials over a period of several months from May 2003 through to November 2003. The focus was to reduce crest loss damage and thereby improve final wall integrity, maintain designed safe berm widths, and ensure long-term stability. Crest loss mechanisms are now understood and are explained in this paper. The preferred solution is outlined; which is a combination of improved blasting and changes in the mining sequence to cater for pre-existing ground conditions. These ground conditions include dynamic hyper saline water with sometimes intersecting steeply dipping discrete structures. Project requirements were defined as mitigating or eliminating crest loss using 127 mm diameter pre-splitting and targeting minimal production blasting vibration levels against the walls. Blast results were measured by post blast visual inspections and video. Blast design input utilised the predictive algorithms built into simulation software when attempting to minimise vibration levels against the walls. Protection of the already fired pre-split line is now achieved using small charges against the wall and timing sequences which form a mask for the later firing main charges. The pre-split spacing is now modified to suit the geology. There eight blast domains identified around the perimeter of the pit, each having varying joint orientation. In addition, blasting the bench adjacent to the berm crest has particular considerations not required by the middle and lower benches. The preferred solution was to purposefully translate this damaged top section of the pre-split bench into a planned subsequent dig zone. The design of this top æweightÆ is a direct response to the nature of the crest loss mechanism.

Jan 1, 2004

Mobile mining equipment presents only a small portion (ten per cent mining project costs but the selected technology will determine to a large extent the mining performance and mine profitability. The actual performance of the selected mobile equipment technology will rely on the support functions, infrastructure, user interface and user acceptance. Optimising the technology to match the circumstances is an increasingly important phase in a mine feasibility study. Smartly done feasibility studies include the possible future needs of changing or building-up of the selected technology. In massive mining applications the machinery faces quite different challenges than in selective or small-scale mining applications. In massive mining applications the efficient and continuous move of large amounts of material has led to the use of increasing degree of automation. This higher degree of automation in a mining application, on the other hand, will be best applied to a smooth and streamlined mining process and operation. Mining methods like block caving support automated operation. Automated mobile equipment needs supportive infrastructure, monitoring and information transfer systems as well as well established working procedures. Too often the user interface and human factor is disregarded during the consideration of automation. Through the available supplier programming tools it is possible to see how much the selected technology provides flexibility in changing production or economical situations, when major rebuilds or replacements are necessary, and view the effects of all these on the mine economy. When adequate technology is available from various sources, the difference becomes from preparing for the future, managing costs and combining the best layout with the most suitable technological solutions.

Jan 1, 2000

By A S. Lund

Optimisation of the underground mining production process benefits from informed decision making during the process of explosive rock fragmentation. Selection of the most appropriate bulk explosive products for underground production blasting is an area of endeavour that offers significant economic upside if correctly and thoroughly undertaken. The explosive selection process is facilitated by a clear understanding of:the physical and detonic properties of the alternative explosive options available; the response of different rock masses to these different explosive options; and the importance of maintaining a clear focus on desirable blast outcomes in order to enhance value creation aspects of the mining production process. The level of understanding of these issues is raised through the application of measurement and modelling technology, quantifying the effects of blast design (and implementation) on process outcomes. Homestake Darlot and DynoConsult applied a range of dynamic blast measurement and outcome modelling techniques in order to explore the relationship between rock properties, explosive properties and mining process efficiencies. A campaign of vibration and explosive Velocity of Detonation (VoD) measurement produced feed data for use in vibration and fragmentation modelling during the extraction of one of the major stoping blocks at Darlot Gold Mine. The paper describes the use of these tools and discusses the understanding gained concerning the limitations and capabilities of, and the reconciliation between, a selection of analysis and modelling approaches.

Jan 1, 2001

By J Rutter, D La Rosa, P Walters, M Scott, L Keeney

Bulk ore sorting technologies, whether surfaced based or penetrative, have seen an increased uptake by the mining industry for preconcentration application. As with all technologies, going through the technology validation process is key to de-risking the operationalisation of the technologies and to demonstrate and confirm predicted value propositions. The ability to laboratory calibrate cross-belt bulk sensors is standard practise for sensor vendors, however transitioning the technology from laboratory to real-world application is a non-trivial process. The industry has taken two main approaches to trialling and validating bulk sensing technologies in operational environments, namely:  Construct an off-line pilot facility at scale, or  Install bulk sensing systems on production conveyors Each of these two approaches have significant advantages and disadvantages and require different experimental design programs and analysis methodologies. Consideration of material movement, heterogeneity degradation, logistical requirements, and financial investment all factor into which approach is most suitable for an evaluation scenario. CRC ORE in partnership with mining companies, have conducted several bulk sensor pilot trials utilising different sensor technologies employing each of the two main approaches outlined above. This paper describes the challenges faced, learnings obtained and outlines a position on how to transition bulk sensing technologies from the laboratory into the operating environment. The case studies presented cover a range of commodity types in both open pit and underground operations.

Nov 10, 2020

This paper explores the use of a Process Safety Management (PSM) system to manage risk in the mineral processing and metallurgical refining industries. Important elements of a PSM system are described. International regulations and non-regulatory guidelines covering PSM for high hazard industries are reviewed. Case studies of incidents in the mineral processing and metallurgical refining industries are presented to understand the lessons learned from failure to manage risks using a PSM system. Conclusions are drawn to adopt PSM in the minerals and metals processing industry as a tool for loss prevention and risk management.

Jan 1, 2003

Among countries afflicted with insLantaneous outbursts of coal and gas, Australia is noteworthy because of lesser disturbances of the seams and of the occurrence of CO2 in the seam gas from place to place. Research sLarted with the 1954 occurrences at Collinsville and Metropolitan Collieries leading to early publications reviewing the problem, describing occurrences and assessing variations in proneness factors in the two affected coal basins.The basic requirements for proneness include coals of high gas sorptive capacity, high ground stress, use of a mining method which provides higher stress concentrations and limits emission of seam gas, including high rates of advance. With CO2 in the seam gas proneness is greater.The mechanism is complex and not fully understood, but involves the coal, the roof, the floor, the gas, the mine opening, the ventilation, the kind of work and the rate of work. Geological disturbances such as faults and dykes increase proneness and tend to localise occurrences. On-occurrence of outbursts in some mines is difficult to explain.Outbursts are seen as a continuing threat to modem deep Australian mining of high rank coal.The simplest contributory factor to reduce is gassiness - despite the low permeability of outbursting coals - and present practices are showing promise. The greatest challenges for the future are partial degasification to below a known threshold figure and confirmation that this reduction is achieved and identification of anomalous geological structures ahead, the most likely locations for instantaneous outbursts to occur. The advances made to date give promise of a future with reducing experiences of uncontrolled instantaneous outbursts. For the Bulli seam particularly, working to achieve prediction and prevention is most urgent.

Jan 1, 1993

By C N. Hatton, K Ward

Tailings operations are inherently reactive as operations personnel continuously contend with a concentrator reject feed (tailings) transient in physical and engineering properties, which places a constant constraint on capital and operational spending. It requires a unique skill set to manage the prescribed distribution of tailings under unenviable conditions. Enter the tailings operator, an oftenundervalued commodity and untapped resource that can provide benefits beyond the rigors of dayto- day operational support. Experience consistently demonstrates that skilled and committed operators can serve a vital function in the safe construction of a tailings storage facility. It takes a village to raise a tailings dam. An important part of this process is establishing a culture of operational accountability and ownership. Operator development training is nothing new. However, we find that many of the intrinsic operator skills are left unexploited, and an operator's experiential knowledge base and creativity are commonly overlooked and underutilized. With proper training and guidance, these skills can be harnessed, contributing to safe dam operations. Operator engagement, when properly facilitated, provides tangible benefits ranging from improved tailings engineering properties to reduced closure costs. One important benefit is helping transitioning tailings management from reactive to proactive. There are many processes involved in the reactive to proactive transition process. One element of that process includes engaging operators in the tailings management process and facilitating legacy ownership. The core of operational legacy ownership is measured and described using five-stage operator engagement rubrics. Levels of operator engagement are presented with a description of the incremental benefits of each stage. An important part of legacy engagement is providing the tools to operators necessary for managing the tailings. Therefore, the approach identifies specific methods used by operations personnel to control tailings distribution and in-place properties. The end goal of leveraging operator engagement is to facilitate committed ownership and transition tailings management from an inefficient, reactive process to an improved, cost-effective, proactive practice.

Jul 1, 2021

After a short theoretical comparison of various typical large bell tops with the bell-less top for segregation and other ,ffects on the material flowing through the equipment proper, a comparative analysis between classical and the new burdening in the furnace is given, showing the theoretical effects of distribution and segregation on the horizontal pressure variations, temperature values and gas composition in the stack. Then some typical theoretical charging patterns of the bell-less top for wall and centre temperature adjusting, pressure drop corrections, dissymmetric local action for blow-in and scaffolding are described. Finally the available practical results on furnaces equipped with the bell-less top are compared with the theoretical statements made before and conclusions indicate that the new approach to burdening blast furnaces is a real improvement.

Jan 1, 1975

Esso-BHP have installed a Production Supervisory Control System that is presently controlling the offshore oil and gas facilities on the Barracouta and Marlin platforms from an onshore master station. This control is achieved with a computerized master station onshore which uses a UHF radio system for telemetry and control. The system is designed to control, monitor, and gather data from a large number of oil and gas production platforms and has flexability to handle future variations in operating conditions. Thn -etom ..ill kn nvt,,ndnd to thn I-lalihn+ rJ,+f, rr , Into +hie -- -A +n the lei...,fieh .,lo+fnrmc A.,;- 1071

Jan 1, 1970