Search Documents

In a ætypicalÆ gold deposit each tonne of ore will contain tens of millions of very fine gold particles, whereas; at Bendigo the majority of gold in each tonne of ore is present in just five to 15 very coarse gold particles, a distribution more akin to diamond deposits. At Bendigo the minimum sample size required for good assay repeatability is estimated at 4.5 t for each assay. Drill core samples are several orders of magnitude too small to generate representative assays.The drilling data are characterised by a nugget effect approaching 90 per cent, a very skewed distribution and, on average, under-report in situ grade by 50 per cent to 75 per cent. Since 2002 Bendigo Mining NL has completed 47 000 m of diamond drilling, 1200 m of on reef development, collected and processed 100 bulk samples (150 t each), 800 mini bulk samples (50 kg each) and processed in excess of 25 000 t of ore through a pilot plant. The results of this work have provided the information required to develop and verify a robust grade estimation procedure. No standard geostatistical manipulation of the drilling assay data can generate an accurate grade estimate as the samples and associated assays are not representative of the ore being sampled. The recognition of this fact was critical as a radical transformation of the raw drill assay data was required to develop a workable methodology for grade estimation in such a high nugget environment. The aim of the transformation was to reduce the nugget effect and high variance and so approach a lognormal assay distribution. Ideally the average drill grade would approximate actual in situ grade and the assay distribution would reflect actual grade distribution within the reefs. Following the data transformation simple block modeling within the defined resources allows grade estimates to be made that can be used in the estimation of Indicated Resources and hence Probable Reserves. The grade estimates have been checked by extensive bulk sampling and processing of 25 000 t of ore (three per cent of total resource) through a pilot plant with planned full scale mining to provide the ultimate verification.

Jan 1, 2004

By S Hapugoda, H Han, L Lu

Charcoal produced from Syzygium Zeylanicum trees was widely used in ancient Sri Lankan iron smelting practices. Charcoal made from Syzygium Zeylanicum tree trunks, branches and leaves were analysed by optical mineralogy and SEM and found to contain unusually high concentrations of calcium oxalate (CaC2O4.H2O – CaOx) crystals in plant cells. Partial and full reduction tests of a high-P Brockman ore were conducted at several temperatures with coke and coke doped with CaOx and CaCO3. It was observed that CaOx promoted reduction and generated comparatively more metallic iron in reduced samples. Furthermore, CaOx encouraged phosphorous partition into slag phases than into the metallic iron, suggesting CaOx can a potential alternative fluxing material to calcium carbonate for treating high-P iron ores in ironmaking processes.

Sep 18, 2023

By V O’Brien

The suitability of magnetic surveys flown at low altitudes to identify buried heavy mineral (HM) strands has long been accepted. This is despite the low intensity magnetic response often obtained from such strands. The fundamentals of the magnetic survey method dictate that the closer the instrument is to the source the stronger the response. As such the optimal elevation for the magnetometer is at or near the surface. Iluka sought to use a ground based magnetometer to aid in the exploration target generation process and allow accurate targeting of exploration drill holes. Following the initial trial Iluka recognised the potential additional application of data obtained by a ground based magnetometer over known strand deposits. The detail of the ground magnetic images can confirm the assumed strand continuity between cross-sections of close spaced drilling and can aid in the definition of the geometry of different generations of mineralisation. The ability to confidently determine that the deposit has not been truncated by post emplacement erosion of the mineralised deposit may enable reductions in drilling requirements as well as assisting mine planning activities. Iluka intends to investigate advanced modelling of the magnetic data to determine the level of strand geometry and HM content resolution that can be achieved from the ground magnetic survey data and its potential application in the mining grade control process.It is anticipated that the surveying of Iluka’s known resource deposits will provide the ability to correlate the magnetic response from new exploration targets with those from known deposits for a given depth, HM grade and mineralogy suite.

Oct 5, 2011

By P Jere

Mechanically coupled rock bolts encapsulated in cementitious or polyester cartridge resin grouts have been widely adopted for various underground rock reinforcement applications. Resin grouts are considered a superior product, however, both systems have their advantages and limitations, with the relative performance, quality installation cost and cycle time as the most notable parameters. Both applications have optimal rock bolt combinations and preferred ground conditions. Cementitious grouts are favourable for use with secondary deep embedment anchors. These are installed using various equipment with a series of autonomous tasks required to complete the installation cycle. The cartridge resin system can be utilised by a bolting or face boring rock drill to complete the full support installation cycle. This reduction in equipment changeouts mid-cycle generally deems it the more practical application and popular choice for primary support. Self-drilling anchors (SDAs) and hollow bolts have been a viable alternative to traditional rock reinforcement in variable and challenging ground conditions. Using a pumpable post installation grouting system, SDAs have proven to aid the quality of installation, but due to the additional equipment and cycle steps associated with application, the cycle time is increased. In recent years, fully mechanised bolting equipment designed to utilise a combination of self-drilling anchors and a thixotropic pumpable resin installed in a single pass has entered the market. This innovation is anticipated to deliver the advantages described above, with fewer limitations, and significantly improved development and rehabilitation rates. St Barbara Mining and Byrnecut Australia, supported by Master Builders Solutions, were first to conduct extensive trials and implement this rock bolting approach in an Australian hard rock underground mine and record the actual performance.

Mar 29, 2023

By W J. Shaw

Mining operations must become more predictable to overcome the volatility that has characterised the mining industry. Comparisons of production against predictions will become more consistent as mining operations merge and expand, as personnel move from site to site, and as public reporting of reconciliations becomes more prevalent. More consistent approaches are already being seen in the industry using the terminology used in this paper and elsewhere.Examples are provided that show how use of the waterfall chart as a reconciliation management tool can provide objective analysis to improve practices.Geometallurgical modelling is becoming more useful and will continue to do so as we move from a few bulk samples to better interpretation of material properties from geological mapping and drill sampling. Reconciliation has evolved to the stage where predictions of geometallurgical properties to optimise mill performance, and of geotechnical properties derived from better 3D geological models, should also be reconciled.CITATION:Shaw, W J, 2014. Reconciliation – outcomes and expectations, in Proceedings Ninth International Mining Geology Conference 2014 , pp 123–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By A Vakili

Dilution is associated with considerable direct and indirect costs in underground open stoping operations. As shown in previous works, an improved ability to predict dilution enables the economic risks associated with unplanned dilution to be reduced. Depending on the width of the orebody and depth of mining, the economic performance of an open stoping operation can become even more sensitive to dilution. It is shown in several well-documented studies that as little as 1 per cent of additional dilution can impose millions of dollars of lost profits per annum. Optimisation of a stoping operation is therefore largely dependent on the ability of the operation to minimise dilution. This can only be achieved through sensible analysis of past and future performance of mined stopes using the most appropriate recent available technologies and tools. This article presents a new design process that utilises advanced geotechnical numerical modelling and various other analytical tools to assist with a more robust mine design of open stoping operations. The focus of this design process is on geotechnical factors affecting dilution during the life-of-mine. A recent application of this optimisation method for a mining operation is presented in this paper as a case study. Through the application of this method and various other operational improvements, the mine was able to deliver more consistent production and lower operating costs over its life-ofmine outlook and was able to reduce dilution by up to 50 per cent and achieve sustainable record high production rates.

Mar 29, 2023

By Stewart R. D, Lawrence W, Youl M. J

The trend towards contracting by major coal mining companies such as BHP Coal and MIM Ltd is examined. Reasons why this trend is occurring are discussed and the concept of partnering is examined. Two case studies are given: the Mt Owen Mine in the Hunter Valley, NSW and the South Walker Creek Mine in the Bowen Basin, Queensland.

Jan 1, 1997

By T Goswami, G Brent

In response to concerns over greenhouse gas (GHG) emissions and an imposed cost in some jurisdictions, many mining houses have committed to reductions in their GHG emissions. However, mining faces particular challenges in this regard, notably from increasing strip ratios. Furthermore, mining activity around the globe is not expected to decrease in the foreseeable future as mineral demand is driven up by the aspirations of rapidly-developing nations. Novel approaches will thus be needed if any reductions in energy consumption and GHG emissions of mining are to be achieved.This paper presents some directions for the mining industry to pursue in reducing their GHG impact, focusing on the difference that blasting methods can make. Importantly, large productivity and revenue gains can also be realised from these methods.Key directions considered here include optimising resource recovery and quality through:reducing coal damage and loss from throw blastingrecovering thin coal seamsproducing cleaner coal with less dilution.Blast design can also significantly improve the productivity of surface mining by:improving muck pile shapingimproving mine equipment productivityimproving scheduling.We show how a particular blasting method can eliminate coal loss in overburden throw blasting and can lead to large increases in coalmine profitability. Thin seams that were previously wasted can also be recovered with this method. Furthermore, the method has been implemented to combine several separate drill and blast cycles into a single cycle, leading to productivity gains.An illustrative example is given to show how increased coal recovery can increase revenues and more than offset any potential GHG emissions liabilities. Overall mine energy and GHG emission intensities can thus be reduced.CITATION:Goswami, T and Brent, G, 2015. Blasting approaches to increase mine productivity and reduce greenhouse gas emissions in surface coal mining, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 635–644 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By W Z. Liu, Q Q. Shi, H T. Yang, X L. Zhang

In order to improve the cutting blasting effect of dimension stone mining, the water coupling directional cutting blasting technology was put forward. Based on the test apparatus and special charge configuration, the mechanism of directional cutting blasting was analysed. Directional device changes the initial equilibrium of the total energy of shock wave effect on blasthole wall. The initial directional crack first appears in the blasthole wall that makes contact with the directional device. Then, two cracks are connected along the direction of the blasthole centre line under the action of detonation pressure and water wedge. The plexiglass tests showed that water coupling directional cutting blasting technology produced cracks along with the predetermined direction completely. The cutting surface was smooth and only a few short cracks appeared around the blastholes. It proved the validity of this technology.CITATION:Liu, W Z, Zhang, X L, Yang, H T and Shi, Q Q, 2015. Directional blasting rock cutting technology, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 815–818 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S Hapugoda, J Manuel, E Donskoi, L Lu

Sinter can constitute up to 80–85 per cent of the total ferrous burden in modern blast furnace ironmaking operations. The mineralogy and microstructure of iron ore sinter play an important role in determining its physical and metallurgical properties. As a result, characterisation of sinter phases is a cost-effective and complementary tool to conventional physical and metallurgical testing of iron ore sinter in evaluating and predicting sinter quality. Over the years, CSIRO has developed a scheme for characterising iron ore sinter that classifies primary sinter phases such as unreacted and partially reacted hematite and magnetite, and secondary phases, including prismatic high-temperature silico-ferrite of calcium and alumina (SFCA), microplaty SFCA (SFCA 1), dense SFCA, secondary hematite and magnetite, glass, larnite (dicalcium silicate; Ca2SiO4) and remnant fluxes. Quantification of these phases has traditionally been carried out by manual point counting under a petrographic microscope; however, new technologies based on automated optical image analysis, quantitative X-ray diffraction and scanning electron microscopy are now available for evaluation. In this study, two sinter samples of varying chemistry were prepared and characterised using both point counting and automated optical image analysis. The implication of the results obtained for the performance of different quantification methods is also assessed.CITATION:Hapugoda, S, Lu, L, Donskoi, E and Manuel, J, 2015. Mineralogical quantification of iron ore sinter, in Proceedings Iron Ore 2015, pp 35–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By F Djukic, T Fisher, G Irving

Questionnaires were sent to 12 underground metalliferous mines in Queensland to enquire how these mines control diesel emissions from mobile diesel engines used underground. Where responses or controls were absent, discussion has been provided. A significant finding concerns secondary ventilation design rates. Some mines were designing ventilation rates to meet the superseded Mines Regulation Act of 1989 which required 0.04 m3/s/kW. The current Queensland Mining and Quarrying Safety and Health Regulation (2001) is risk based. In line with other jurisdictions, including New South Wales (NSW) and most Provinces in Canada, a minimum ventilation rate of 0.06 m3/s/kW is acceptable. However, this design ventilation rate will vary in practice depending on the diesel engines and controls. Dedicated ventilation engineers and technicians should be appointed to evaluate the effectiveness of the ventilation system. Personal exposure monitoring is required to confirm that exposure standards are not being exceeded. The primary control practice should be to reduce the emission at source. This can be ensured by purchasing low emission (Tier 2, Tier 3) equipment. In addition, the use of ultra low sulfur fuel (et al, 2002). Diesel fuel with a low aromatic content such as Eromanga diesel fuel will also mean employees are exposed to lower levels of poly-cyclic aromatic hydrocarbons. These controls should be carried out in parallel with good maintenance practices. Preventative maintenance should be programmed and emissions be routinely tested, including both gaseous and particulate pollutants and compared against defined criteria. According to McGinn, 2002, there are a number of fundamental tools necessary to carry out preventative maintenance. These are outlined in maintenance guidelines and best practices for diesel engines in underground mining produced for the Diesel Emissions Evaluation Program (DEEP). An effective diesel emission management system needs to be fully integrated within the Safety and Health Management System. These requirements are further discussed in this paper.

Jan 1, 2007

By J Rowland

"Ventilation models are invaluable tools for both prediction of routine daily ventilation changesin an operating mine to circuit performance expectations at the mine in 20 yearsÆ time. Arguably ventilation offi cers are becoming increasingly reliant on maintaining an accurate ventilation model with which to do their work. This paper relates to the practical assessment of the accuracy and thus ability of a mine site ventilation model to be reliably utilised on such varied tasks. The author's experience shows that in some cases the incumbent model is found to be in a state of tune that demonstrates a mine wide detailed assessment of branch resistances is simply not required. The money spent on a detailed mine wide ventilation survey that is not required would be far bett er served purchasing much needed monitoring equipment, rather than fixing something that is possibly not even broken. The term ænot rocket scienceÆ has been incorporated into the title of this paper because it appears that many practitioners believe that circuit validation is diffi cult. As long as clear att ention to detail is paid to the actual data collection process then drawing an accuracy comparison between the circuit performance and the model performance at any particular point in time, is really very simple. This paper will show a manner in which a circuit can be analysed to determine its actual state of health by using various diagnostic tools and tips. It will help ensure that subsequent work scopes to address any highlighted model defi ciencies can be more effi ciently scoped and targeted. It will hopefully remind operational people that such self assessments can easily be done æin houseÆ if the appropriate steps are followed."

Jun 1, 2012

By B Waldon, M Valastro

A coal dust explosion is one of the most significant risks in the harsh and complex environment of an Underground Coal Mine (UCM). Reviewing literature, regulations and existing systems surrounding explosive dust management shows that there have been few advancements in managing this risk over the past 90 years. Legislation has remained relatively stagnant and minimal systems are implemented in the real world that can simplify, standardise and improve the effectiveness of UCM explosive dust management. To help bridge this gap, Corehesion, in collaboration with an UCM has designed, developed and implement an Explosive Dust Risk Mitigation System (EDRMS) utilising components of Business Intelligence (BI) that is capable of real-world use in industry. To do this the existing explosive dust management process at the associated research mine was evaluated to form high-level and detailed design requirements, focusing on digitally simplifying the procedure, not replicating it. The system was then iteratively and incrementally developed and implemented at the research mine to commence real-world use. The developed BI platform is compared with the existing process to highlight the advancements in performance transparency, efficiency and optimisation of UCM explosion mitigation. This comparison and evaluation of the real-world system implementation at the research mine demonstrate its success in automating procedure steps, providing a readily accessible source of data and enabling a proactive approach to planning and managing explosion risk mitigation. In addition to improvements just for the research mine, this EDRMS created directly address many Queensland regulatory audit findings. By finalising the total system and making the highlighted changes for standardisation, this BI system will have the adaptable capabilities for implementation across the UCM industry. As accurate data availability improves at UCMs, further work can be done to improve the systems’ optimisation techniques and integration of other risks.

Apr 16, 2024

By H Kurth

Mining geologists utilise many technologies to map, sample, measure, model and plan before and during the mining process. Predicted ore quality rarely corresponds with feed quality determined by process operators. Objectively measuring conveyed material quality accurately in real time avoids disagreements over mined ore quality and generates opportunities to improve mill feed quality.This paper discusses the well proven PGNAA (prompt gamma neutron activation analysis) technology used in the GEOSCAN-M elemental analyser that is ideally suited to measuring composition of primary crushed conveyed material in real time. Representative, continuous, fully penetrative measurements are unaffected by particle size, belt speed, mineralogy, dust or layering on the conveyor. Material can be directed to processes or stockpiles by utilising measurement increments of typically one to five minutes and then activating diverters to direct increments to the correct location. Waste, low-grade or deleterious material can be rejected to waste dumps or stockpiled for later processing. Material meeting a product specification can bypass unnecessary processing. Paybacks in weeks have been achieved for such applications. Process operators are able to control the blend of ores fed into the mill to improve processing performance and use measurements for ore reconciliation and metal accounting. Utilising the technology to upgrade ore quality after mining and before processing is beneficial in improving plant economics.The technology has been successfully utilised in base metals, ferrous metals and industrial minerals. Mining geologists can determine ore quality being produced in real time and modify the ore quality prior to milling. Ore feed quality measurements are also used by process operators in optimising plant performance. The elemental content can help identify geometallurgical domains as well as other major changes in quality, which may affect processing. This paper outlines proven applications and case studies and proposes some innovative applications.CITATION:Kurth, H, 2017. Measuring ore quality using real-time on-belt elemental analysis – more than grade control, in Proceedings Tenth International Mining Geology Conference 2017, pp 213–220 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By A I M Ritchie

The pyrite oxidation rate is a process central to both the performance of bio-oxidation heaps, used in the pre-treatment of some refractory gold ores, and to the levels of pollution in acid rock drainage (ARD) from pyritic waste rock dumps. A goal in bio-oxidation heaps is to achieve high oxidation rates in the heap as a whole. In comparison, one way to mitigate the environment impact of ARD, is to reduce the overall oxidation rate in the waste rock dump since pyrite oxidation is the primary pollutant generation process. In both bio-oxidation heaps and waste rock dumps the overall oxidation rate of the pyritic material (the intrinsic oxidation rate) at these sites. Much research has been conducted over the last 40 years or so on the oxidation rate of pyritic material with particular emphasis on the catalytic role played by bacteria. More recently mathematical models and field measurements have clarified the extent to which oxygen transport rates are rate limiting, what the dominant oxygen transport mechanisms are and the physical properties of the heaps which have most impact on these transport rates and on the overall oxidation rate. How the performance of bio-oxidation heaps can be optimised and how the pollution load in drainage from waste rock dumps depends on gas transport mechanisms is briefly reviewed. The sensitive of the overall oxidation rate in bio-oxidation heaps and waste rock dumps to details of the intrinsic oxidation rate is quantified.

Jan 1, 1994

By P Stewart, S Cowie, A Offer, J Carpenter, E Jones

The Ban Houayxai Gold-Silver Operation is a producing asset for Australian-based copper and gold producer, PanAust Limited. The Operation lies within PanAust’s 2600 square-kilometre Phu Bia Contract Area in northern Laos. Commencing production in 2012, Ban Houayxai is operated by PanAust’s Lao-registered company, Phu Bia Mining. PanAust owns a 90 per cent interest in Phu Bia Mining. The Government of Laos owns the remaining 10 per cent. The Operation mines an intermediate sulphidation epithermal gold-silver deposit and comprises an open-pit feeding ore to a conventional carbon-in-leach process plant. Metallurgical recoveries for gold and silver are approximately 75-85 per cent and 55 per cent respectively. To year-end 2017, the Operation had poured 0.65 million ounces (oz) of gold and 4.7 million oz of silver. The Ban Houayxai Ore Reserve supports a mine life of approximately four years from the end of 2017. The Ban Houayxai deposit is in an early Permian volcano-sedimentary unit which is part of a late Carboniferous to early Permian (310–270 million years ago) volcanic-plutonic sequence of the Truong Son Fold Belt. The deposit formed when hot saline (240–415°C, 2.7–13.0 weight per cent NaCl equivalent) fluids ascended from a geologically fertile island arc porphyry into overlying volcanics along a fault or faults in the early Permian (290–256 million years ago) (Manaka et al, 2014). CITATION: Carpenter, J, Cowie, S, Stewart, P, Jones E, and Offer, A, 2018. Machine learning at a gold-silver mine: a case study from the Ban Houayxai Gold-Silver Operation, in Proceedings Complex Orebodies Conference 2018, pp 82–85 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By J Dwyer, G Turner, D Pridmore, M Urosevic

Due to their ability to produce high-resolution images of the subsurface to great depths, seismic surveys provide critical inputs to almost all oil and gas exploration projects. However, with some notable exceptions, seismic surveys have rarely been used in mineral exploration. In the past, this was due to both technical and financial reasons. Significant developments on both fronts mean that seismic surveys can now offer substantial benefits to mineral exploration and mining, and surveys conducted for exploration can provide important data sets for mine planning over the life of a mining project.We present case history data that show that seismic surveys can greatly assist with mapping the 3D distribution of lithologies and alteration and, in favourable circumstances, directly detect mineralisation in and around mineral systems. As a result of their high spatial sampling density, seismic surveys are also highly effective at mapping structures that can remain undetected or poorly characterised by drilling alone. These structures may host or provide important vectors to mineralisation. They can also be particularly important when planning shafts, raise bores, declines, stopes and open pit walls. A further benefit of seismic surveys is that they can remotely provide information on geotechnical rock parameters that are used for rippability, slope stability, blasting and ground support.CITATION:Turner, G, Urosevic, M, Pridmore, D and Dwyer, J, 2015. Exploration and mining unified through seismic imaging, in Proceedings Third International Future Mining Conference, pp 117–122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By T Raynlyn, S Hapugoda, V Nunna

The predominant phase in most Marra Mamba, channel iron deposits and detrital iron ore deposits is goethite. Goethite abundant iron ore fines tend to have complex mineralogical associations and fine dissemination of gangue material. These ores are typically challenging to process using conventional beneficiation methods. With declining ore grades, there is a need to develop new processing routes for low-grade goethitic ores/fines.Comparative process amenability studies were carried out using two different processing options to recover iron with low alumina and silica content from a low-grade goethite-abundant iron ore fines (-2 mm) sample from the Pilbara region of Western Australia. The first option involved dehydroxylation at 350°C and 400°C, followed by grinding dehydroxylated samples to 100 per cent passing 106 µm and magnetic separation. The second option was processing raw sample by gravity separation using a Floatex density separator. The performances of the two processes are discussed in terms of the iron grade-recovery responses, and an optimal processing route is proposed based on the findings from these tests.CITATION:Nunna, V, Hapugoda, S and Raynlyn, T, 2015. Process amenability studies on goethite-abundant iron ore fines, in Proceedings Iron Ore 2015, pp 165–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By S Vearncombe

SpaDiSÖ is a revolutionary approach to the spatial analysis of point data using geometry to analyse geometry! SpaDiSÖ uses each and every spatial relationship and is not dependent on mathematical models. For n points there are n2 û n spatial relationships and, because of the square function, the method yields interpretable results for both small and large data sets. SpaDiSÖ is an alternative to variography for directional studies. At the regional scale, the analysis can assess distribution patterns of mineralisation and potential controlling structures. At the deposit scale, the characteristics of zones of mineralisation such as direction, spacing, high-grade ore direction and grade distribution can all be deduced.

Jan 1, 2000

By M Dietrich

The paper describes an efficient method for analysing the different attachment kinematics of excavators and other linkages by taking into account digging forces, the workspace and the stability of the machines. The different attachment kinematic systems of hydraulic excavators and a æclassical analysing methodÆ will be presented. The method was integrated as a plug-in for the multibody simulation (MBS) software MSC.ADAMS to create an easy to use solution for design engineers. A comparison of the new MBS-solution with the classical static analysis is a part of this paper and shows the advantages of the new method. This takes into account the manifold and new dynamic analysing opportunities, as well as more detailed models leading to more accurate results.

Sep 26, 2011