Search Documents

By Stevenson I, Dickinson W, Taylor R. N

Despite flash smelting's widespread use little is known about the actual processes taking place in flash furnace shafts and comparatively few reports of sampling campaigns have appeared in the published literature. his paper reviews the previous reports of the use of horizontal trough samplers and analyses their expected collection efficiency. In the light of the deficiencies revealed by this analysis an isokinetic sampler was produced and a vertical sampling technique was also developed to obtain samples from directly below the burners in the shaft of the flash furnace at the Kalgoorlie nickel smelter. Comparison of the sizing of the samples obtained with the horizontal trough and isokinetic samplers confirmed the theoretical analyses and showed that the trough samplers were not collecting the fine particles. Besides providing data to validate mathematical models of the burners and shaft, chemical analyses of the shaft samples showed that the coal in the charge was reacting preferentially and that the plume of at least one of the burners was being deflected from its axial position. In the region directly below the burner there was evidence that the disperser on the burner was imparting more momentum to the coarser particles and that these were concentrating in the outer regions of the particle plumes issuing from the burners.

Jan 1, 1992

By Laros T, Schoenbrunn F

Deep paste thickeners have been proven capable of consistently producing medium to low slump material for disposal without the need for filters. However, proper design of the entire system is critical for a paste project to he successful. Some of the factors that must be carefully considered in design of a paste system include thickener sizing, tailings inipoundineni design, underflow pumping, and control system.

Jan 1, 1998

By W Newns

This paper describes laboratory and in situ tests and determines a set of parameters for stiffness and strength properties for a weak sedimentary rock mass, the East Coast Bays Formation of Auckland. The parameters derived are discussed in relation to peak strength and in respect of deformation limits associated with sequential excavate and support (SEM) or conventional tunnelling.

Mar 8, 2011

By Moritz P

Thiourea has been recognised for a long time as an acid-stable complexant for gold. Generally, the use of thiourea has been shown to exhibit enhanced leaching kinetics compared to cyanide but suffers the disadvantage of excessive reagent consumption. Thiourea leaching is particularly com- patible with the extraction of gold from refractory ores. This is due to the need for an oxidative pretreatment to liberate the gold. Such pretreatments typically result in the production of an acidic residue. The application of novel thiourea leaching technologies to the extraction of gold from a bioleached pyrite concentrate was investigated. The interac- tion of leach variables with thiourea consumption and gold extraction was established. An economic assessment of thiourea leaching was compared with conventional cyanidation. The results indicated that gold leaching of the bioleached residue using thiourea compared very favourably with cyanidation.

Jan 1, 1991

By P J. Hawke, M F. Flis

The Hamersley Basin of Western Australia holds significant tonnages of detrital iron deposits. Formed by a cyclic weathering and eroding sequence of nominally barren banded iron formation, they may form rich proximal accumulations of iron cemented gravels distal from any obvious hard-rock iron mineralisation. While generally small, they nonetheless represent excellent economic targets as they are near surface and easy to mine. The relatively high density of iron detritals, when compared with their sedimentary hosts, makes the gravity method the primary method of exploring for these blind deposits. Identification of possible trap sites is used as a precursor to gravity surveying, with magnetics used as an ancillary method prior to drilling. Application of the gravity method in this terrain is not straightforward. Detrital trap sites are best developed next to the spectacular cliffs that form the range fronts to the Hamersley Ranges. Precise terrain corrections and use of first vertical derivatives are routinely applied to gravity data in an effort to map every possible gravity high that may reflect the presence of a detrital accumulation. Extensions to Hamersley Iron Pty LimitedÆs BS2D deposit were discovered by the routine application of gravity. This methodology has been used to create a model by which exploration for detrital deposits continue to the present day.

Jan 1, 2002

By J V. Mehrabani, A R. Sayadi

Adequate estimation of equipment costs is a key factor in a feasibility study and in evaluation of design alternatives for mining and mineral processing projects. Inaccurate early cost estimation could lead to the elimination of investment benefits. However, this estimation is complex and time consuming because of data accessibility problems and consequently access to a rapid, up-to-date and accurate tool is desirable for carrying out cost estimations.This paper describes the development of models for estimating capital and operating costs for a jaw crusher, which is used as the primary crusher for a wide variety of mineral beneficiation plants, applying single and multivariate regression analyses, together with the design of experiment approach, based on principal component analysis. Explanatory variables include gape size, length of feed opening and power as numeric (quantitative) variables and toggle type (single or double) and the existence of extra heavy duty construction as categorical (qualitative) variables. The performance of each model has been investigated and comparing the estimated R-squared (R2) of each model, the best was selected and its validity examined. The cost models include the capital and operating costs along with the operating cost components. The results indicate that the suggested best cost model is sufficiently accurate for use in feasibility studies.

Sep 26, 2011

By N J Welham

A commercial enargite concentrate was mechanically milled in inert and oxidising atmospheres for 10 hours. No substantial effect was observed in either an inert atmosphere or in air other than a broadening and weakening of the diffraction peaks. Milling dry in oxygen or wet in air was dramatic with a significant reaction occurring which formed arsenolite, As2O3 and CuSO4.5H2O, both of which are readily soluble.A small amount of SO2 was also formed. Dissolution in acid left CuS as the major phase implying incomplete oxidation. The small fraction of tennantite in the sample was comparatively resistant to oxidation.

Jan 1, 2001

Almost all the countries of the south-west Pacific and the Australian states have recently completed or have commissioned mineral royalty reviews. The prime reasons for this widespread and consistent action is the desire of the governments of these entities to redress perceived effi- ciency and equity imbalances and to ensure that the revenue raising motive does not override the necessity to maintain mineral exploration and development incentives. Governments are tending to adopt royalty systems comprising a com- bination of base royalty and a profit component. Resource rent royalty and royalty holidays have been introduced and anomalies, such as royalty free gold production, still exist but appear to have uncertain futures. Tasmania ranks as the Australian state with the lowest aggregate royalty levy/production value ratio whilst Papua New Guinea has the highest royalty objective achievement level in the south-west Pacific region.

Jan 1, 1988

By N Akizawa, A Tamura, S Arai

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Reaction products between high-temperature hydrothermal solution/uppermost mantle peridotite or lowermost crustal gabbro have been reported along Wadi Fizh of the northern Oman ophiolite; they are named as ‘mantle diopsidite’ and ‘crustal diopsidite’ respectively (Figure 1).The mantle diopsidite contains Cr-rich minerals like chromite, Cr-rich diopside (<2.5 wt per cent Cr2O3) and Cr-bearing grossular (<7.0 wt per cent Cr2O3). The chromites are varied in shape in the mantle diopsidite, euhedral to anhedral chromite grains contain globular inclusions of grossular and chlorite, and film-like chromite veinlets branch off from partially dissolved coarse chromite grains. In the crustal diopsidite, fine chromite grains are included in oscillatory-zoned skeletal uvarovite, especially in its high-Cr zones. The uvarovites are rich in rare earth elements (REEs). Direct laser ablation – inductively coupled plasma – mass spectrometer (LA-ICP-MS) analysis of the primary fluid inclusions detected Na, but not K.Our detailed studies of Wadi Fizh diopsidites clarify that the high-temperature hydrothermal solution dissolves chromite grains at the uppermost mantle section and precipitates hydrothermal chromite at the lowermost crust section. In addition, REEs were mobilised in the hydrothermal solution together with Cr. The hydrothermal solution involved in the diopsidite formation is assumed to have been rich in NaCl, and could mobilise appreciable amounts of Cr and REE.CITATION:Akizawa, N, Arai, S and Tamura, A, 2015. Chromium and rare earth elements mobility by sodium-bearing high-temperature hydrothermal solution – an example from mantle diopsidite and crustal diopsidite, in Proceedings PACRIM 2015 Congress, pp 291–296 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

During the 1950's there was a flurry of activity on the design of main ventilation shafts for mines. More recently, a new ana- lysis was commissioned in relation to the multi-shaft, nuclear waste isolation facili- ties currently under design in the United States. This paper presents the major find- ings of that study and should prove of value as a reference in the design of proposed new shafts. An overview of mine shaft resistance introduces the effects of the shaft walls, fittings, conveyances and shaft stations. Each of these is analyzed in turn. A com- pletely new technique is described, which facilitates the estimation of wall resis- tance. The effect of size of a conveyance is quantified and shown to be dominant when the cage occupies more than 30 per cent of the shaft cross-section. The dynamic effects of a moving conveyance are also analyzed.

Jan 1, 1988

The mining industry is quite often faced with declining selling prices for its products in the face of rising prices for the input cost resources that it uses. Blasting is a key activity within the mining system and has a vital role to play within the Mine to MillTM concept. It is therefore important that blasting makes a positive contribution to mine profit and productivity. There are several variables involved in considering the profitability and productivity of blasting. The rock types and structures, the bench height, the blast hole drill rig specifications, hole diameter, spacing and burden, explosive loading and initiation and blast size fragmentation. Productivity accounting is a methodology which is used elsewhere to give additional insights into the productivity and pricing factors that drive the financial performance of a business. Miners know intuitively that productivity and pricing influence costs and profit, but only with productivity accounting can the dollars involved be calculated. Drilling and blasting are part of a chain of unit operations in a mine. For an owner-miner, drilling and blasting would be considered as cost centres and a productivity accounting cost model approach would be relevant. On the other hand a contractor is likely to consider drilling and blasting as a profit centre, in which case a productivity accounting profit model approach would be appropriate. Both of these will be explained. The paper provides a basic outline of deterministic productivity accounting and demonstrates its application to blasting. Drilling and blasting data from a mine was obtained for a two-month period. The change in productivity and prices was calculated to obtain the dollar contributions from them towards the change in cost. It was determined that although there had been productivity dollar gains these were offset by larger pricing dollar losses, the net effect being that total drilling and blasting costs increased. The productivity accounting analysis gives the facts and the mine is in a position to establish priorities based on knowing the dollar contributions of each input used.

Jan 1, 2001

By C Swamydas

VV Mineral (VVM) group of companies is the largest and the first private producer and exporter of beach sand mineral products in India. During 2010, the company produced and marketed around 750 000 tons of saleable products. Their operations are mainly in the state of Tamil Nadu and Andhra Pradesh, India. Almost all the wet pre-concentration plants use sea water as the concentration medium, since there is no fresh water source available near the deposits. The mines are located along the south-east coast of India in the states of Tamilnadu and Andhra Pradesh. The orebody varies in terms of mineral assemblage, slime content, grain size, and surface coating resulting in different behaviour of the minerals. Three different deposits containing ilmenite of different TiO2 content were studied. The study shows that there is no significant impact of using sea water for wet concentration prior to high tension separation of ilmenite. There is no significant variation in recovery and purity of ilmenite produced from these deposits when wet concentration of the deposits were carried out with sea water as the concentration medium and whether the concentrates were washed with fresh water or not before dry separation using High Tension Roll Separators (HTRS).

Oct 5, 2011

By D Caffrey

To demonstrate the advantages of using electronic delay detonators over pyrotechnic detonators, a trial using the DNES Dynatronic System was conducted at the KCGM Mount Charlotte operation in 1998. The trial clearly demonstrated that accurate control over the firing delay time between blastholes can lead to fragmentation improvement and ground vibration energy control which are two important issues for the Mt Charlotte underground operation. Excellent fragmentation was achieved by employing a 12 ms delay sequence. Detailed fragmentation analysis has shown a 10 to 20 per cent passing increase for the rock fragment size from 0.1 to 0.4 m compared with the pyrotechnic detonator firing. There was no increase in ground vibration level on the surface with the electronic detonator firing even though the electronic detonator firing had a much shorter blast duration than the pyrotechnic detonator firing. In fact, our energy calculation has clearly shown that much less energy had been propagated to the surface from the blast using electronic detonator firing.

Jan 1, 1999

By I Canbulat, A Mcquillan

This paper presents a parametric analysis showing the impact of virgin in situ stresses on a shallow (less than 100 to 150 m) high slope in a jointed sedimentary rock environment. Slope stability is assessed at varying ratios of slope orientation and horizontal stresses. The results of this study indicate stress conditions should be included in stability assessments of excavated slopes, particularly where structure is orientated perpendicular to the direction of horizontal stress. Some consideration of stress state is applied in deep open cut pits (eg those with planned excavations of 400–1200 m) (Myrvang et al, 1993; Stacey et al, 2003; de Bruyn et al, 2014; Kozyrev et al, 2015). Dodd and Anderson (1972), Kalkani and Piteau (1976), Lee (1978), Coulthard et al (1992), Noorani et al (2011) have studied the effect or horizontal stress and its impact on slope stability, showing that tensile stresses tend to develop at the crest of the slope, with larger tensile zones for higher horizonal stresses and steeper slope angles (Stacey, 1970, 1973; Sjoberg, 2013). However, the consideration of virgin stresses on shallow slope stability is less frequent (Lynch et al, 2005; Dight, 2006; Lucas, 2006; Sjoberg, 2013). This has led many geotechnical engineers to believe the impact of virgin in situ stresses on open cut slope stability is minimal and not worth time or consideration in modelling, or their effects on slope stability are still poorly understood (Stacey et al, 2003; Sjoberg, 2013).

Nov 29, 2022

By A Lines

This paper addresses a gap in longwall multi-seam interactions and their predictions, providing a case study for future multi-seam operations for both anticipated conditions and a method for understanding the changes in stress regime. Multiple panels were modelled with the results analysed and compared to panel experiences to validate the parameters and properties. The software chosen (LaModel) is a numerical modelling package designed to model stresses and displacements on thin deposits. It utilises a displacement-discontinuity variation of the boundary-element method and has been used extensively throughout both the United States and Australia in multi-seam operations. Analysis of the results demonstrates a clear correlation with the above workings and regions of significant strata instability. This provides the opportunity going forward to analyse new models and incorporate into mine planning and geotechnical designs. Continuous site-based assessment should be undertaken at multi-seam operations to better understand and quantify likely vertical stress levels within the workings. With a detailed analysis of models prior to extraction and a review of models post extraction. Further research is required as LaModel is limited to vertical stress and it is likely that interactions impact both the horizontal and shear stress regime. 3-dimensional modelling could further assist in this understanding, combined with a thorough stress monitoring regime. CITATION:Lines, A, 2018. Modelling multi-seam interactions for longwall mining, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 185–195 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

This paper examines the complex interplay of deposit characteristics, mining plans, tailings disposal techniques and rehabilitation requirements on planning for mineral sands operations. All component parts of this mining cycle are interdependent and cannot be evaluated in isolation when optimising a mineral sands operation. This is most evident when projects are large-scale or involve resources that contain complexities such as high slimes content, consolidated hard band materials, acid forming materials and radioactive materials. Projects located in environmentally sensitive areas add further to the need for more stringent planning. This paper describes the analysis techniques adopted by Hatch to evaluate mining and tailings placement options for a dredging and floating concentrator system. The principles and methods used in the analysis are applicable to any mining system involving the complexities listed above. The focus of this paper is on the reconstitution of mined material as tailings and the impact of this process on mining schedules and tailings construction and placement options.

Jan 1, 2001

Samples weighing O·25 g are fused with 1 g potassium hydrogen sulphate, leached with 5 ml. of hydrochloric acid, and then diluted with another 5 ml. of acid. After settling, an aliquot of the clear solution is reduced with stannous chloride, and then a zinc dithiol solution is added to form a coloured tungsten complex which is extracted with petroleum spirit for comparison with standards.Concentrations down to 4 p.p.m. may be analysed at a rate of 100 determinations per man-day of 8 hr.

Jan 1, 1970

Operating metallurgists spend a significant part of their time running plant trials to compare two or more conditions in order to improve the process, such as a new reagent, flow sheet or piece of equipment. The best way to conduct such a trial is as a paired experiment when testing two conditions (eg 'old' and 'new') or a randomised block design when testing more than two conditions. These experimental designs should always be preferred over alternatives if their requirements can be met, because they block the effect of uncontrolled variables ('covariates') and are the most statistically efficient, ie they will lead to the required level of confidence in the outcome faster than other methods. Sometimes, however, it is not possible to switch condition easily, which is a prime requirement of these methods. In such cases the only option may be to switch condition once only, and compare the process performance before and after the switch. Examples are testing grinding media, large equipment, or long residence time processes such as leach trains or CCD thickeners. This paper considers some data analysis methods to deal with this situation. Modelling with intervention analysis (IA) uses regression models with a dummy variable to indicate the presence or absence of the test condition. IA with a time series model ensures that the residuals are uncorrelated. IA with a process model helps to deal with the problem of covariates. The reference distribution is a method free of any statistical assumptions but is less powerful than the other methods. Cusum charts are a helpful visual aid to interpreting time trends. A combination of these methods can help improve the confidence in the final decision. None are as good as a formal experimental design such as a paired trial.

Jan 1, 2008

By D Anderson, W Timms

"A geotechnical centrifuge can characterise and model the interaction of tailings and fluids over very long time periods by accelerating drainage and consolidation processes. This technology can be considered an environmental ‘time machine’ for designing and evaluating tailings storage projects and verifying numerical models. The Broadbent G-18 geotechnical centrifuge (2 m diameter, up to 875 rev/min) and associated equipment is a unique facility commissioned in 2011 at UNSW Australia for applied research in low-permeability materials such as mine tailings. Two centrifuge modules are available: the permeameter module for characterisation and physical modelling and the strongbox module for physical modelling.This paper presents examples of geotechnical centrifuge applications for the: consolidation of slurries and dewatering design of earthen barriers compatible with tailings chemistry prediction of contaminant mobility. The specifications and capability of the UNSW Australia geotechnical centrifuge and associated instrumentation is also presented, along with preliminary analysis of the confidence intervals associated with permeability testing of a set of samples of varying heterogeneity. Drainage velocity through a mine tailings sample increases linearly with g-level in the centrifuge permeameter until tailings consolidation occurs. Alternatively, geotechnical centrifuge experiments can be designed to limit consolidation so as to quantify permeability changes that may occur with geochemical interactions between fluids and mine tailings or earthen containments. Reactive solute transport through mine tailings can be simulated at realistic solid:liquid ratios when chemical equilibrium is maintained during geotechnical centrifuge testing. Carefully designed physical models of tailings disposal tested at accelerated gravity can therefore provide a realistic evaluation of tailings consolidation and drainage and the potential for subsurface migration of contaminants from mine tailings over long time periods.CITATION:Timms, W and Anderson, D, 2015. Geotechnical centrifuge technology for characterising the interaction of tailings and pore water over decadal time periods, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 247–252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By Canterford J. H, Sparrow G. J, Dyson N. F

Pressure leaching of a bulk flotation concentrate prepared from a complex Cu-Pb-Zn sulphide ore was carried out at 150 and 190¦C under 1050 kPa oxygen overpressure in 1 L and 4 L titanium autoclaves to extract zinc, and to obtain residues for smelting tests and leach liquors for purification and recovery of the zinc by electrowinning. Dissolution of 95% of the zinc was achieved at both temperatures. Copper and iron dissolution and the degree of oxidation of the sulphide sulphur to elemental sulphur or sulphate depended on the temperature of the leach. At 190¦C, a jarosite (a basic iron sulphate) was the major iron-containing material in a residue that contained 17% total sulphur. Its formation was associated with dissolution of 18% of the iron. At 150¦C, oxidation of the sulphide sulphur and dissolution of the iron were significantly less. Only 7% of the iron was dissolved and a residue containing 25% total sulphur, present as a lead jarosite, lead sulphate, and elemental sulphur, was obtained. The formation of small pellets of unreacted sulphides coated with elemental sulphur caused problems during the leaching at 150¦C, and also during scale-up from the 1 L to the 4 L autoclave at 190¦C. At 150¦C the concentrate required two stages of leaching to achieve dissolution of over 90% of the zinc. These problems are discussed.

Jan 1, 1989