Search Documents

By T B. T Nguyen, L Matthews, D O’Dea, T Honeyands, T Harvey

Productivity and fuel consumption of the blast furnace is driven by the quality of the iron ore sinter, which in turn is related to the sinter mineralogy. The sintering conditions including temperature and gas composition have a significant influence on the formation of melt and finally the mineralogy of the sinter. In this work, analogue sinter tablets were produced from iron ore fines in a laboratory furnace with tightly controlled temperature profile and oxygen partial pressure in the gas. The mineralogy of the sinters was analysed using reflected light microscopy. The results showed that increasing thermal enclosed area (area enclosed by heating and cooling curve above a reference temperature) reduces primary hematite and platy silico-ferrite of calcium and aluminium (SFCA) contents. This is attributed to increasing melt formation, leading to greater assimilation of the iron ore particles. Lower magnetite was found for tablets with greater median pore size, which is thought to be due to greater oxidation of magnetite to hematite during cooling in air. It was also found that higher alumina content was found to result in more SFCA formation under the same heating/cooling conditions, whereas tablets with higher goethite had higher assimilation and produced more secondary hematite on cooling. Finally, it is necessary to relate the enclosed area to the temperature at which the melt formation becomes significant which strongly depends on chemical composition of the ore studied.

Nov 8, 2021

By J Rostami, T Afshar, M Sharifzadeh

Accurate estimation of rock load and selection of types of ground reinforcement to match post-failure behaviour of rock mass are important issues to assure tunnel stability. This paper focuses on the main factors affecting rock load to evaluate the capabilities of the existing models for prediction of rock load. Rock mass properties, project features and excavation method, as well as ground conditions and stress condition were found to be the key factors affecting the magnitude of rock load. Field data from tunnels of about 37.5?km driven in several geological structures in non-squeezing ground was used in this study. An in depth statistical analysis was performed on data to find correlations between the input parameters and measured/observed rock load. A weighting system was proposed to obtain the proper contribution of each factor for estimation of rock load in tunnelling through various ground conditions. The new classification system offered predicted values for rock load that were in a good agreement with the actual field measurements. The high disturbance factor (D>0.4) was the prime factor which controlled the rock load. Rock mass quality was the second key factor influencing rock load, which could be estimated by GSI, GSIresidual , especially when combined with tunnel depth.CITATION:Afshar, T, Sharifzadeh, M and Rostami, J, 2014. Estimation of rock load for tunnels with different disturbance factors, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 3–8 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J G. Shellnutt, Y Iizuka, T W-Y Hsia, T-C Liu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The formation of magmatic oxide ore deposits hosted in chemically-evolved layered gabbroic intrusions is attributed to a variety of petrological processes, but there is little to no consensus on the general applicability of each model. Complicating the matter further is that many layered gabbroic intrusions are spatially and temporally associated with alkaline A-type granites, suggesting that there is a petrogenetic relationship between the two types of chemically different rocks. Our experimental results show that petrological modelling using a starting composition of high-Ti basalt from the Emeishan large igneous province can produce evolved silicic liquids that resemble the compositions of microgranular enclaves from the syenitic unit of the bimodal, oxide ore-bearing Baima igneous complex. The experimental results confirm that bimodal gabbro-granitoid complexes can form from a common parental magma and that early crystallisation of Ti-rich magnetite can explain the formation of the oxide ore deposits in the lower parts of the layered gabbroic intrusions. We conclude that crystallisation of a typical high-Ti basaltic parental magma can produce world-class giant magmatic oxide ore deposits and that the occurrence of some alkaline granites may be an indicator of their presence.CITATION:Shellnutt, J G, Hsia, T W-Y, Liu, T-C and Iizuka, Y, 2015. Cogenetic formation of the peralkaline syenite and oxide ore-bearing layered gabbroic intrusion of the Baima igneous complex, Emeishan large igneous province, south-west China , in Proceedings PACRIM 2015 Congress, pp 317–324 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By R M. Yanamandra, M Kumar, S K. Tripathy, N Mangadoddy, P Sudikondala

Spiral concentrators are one of the flowing film gravity concentration devices used to beneficiate coal and mineral ores. The aim of the current study is to understand the particulate flow and separation performance of an LD9 spiral concentrator using a multi-phase Computational Fluid Dynamics (CFD) model. The CFD model utilises the Algebraic slip mixture model to simulate particulate flows. The model employs the Renormalisation group (RNG) k-ɛ turbulence models to resolve the fluid turbulence. Initially, the volume of fluid method was adopted to track the water-air interface. Simulations were then carried out at low (0.3 and 3 wt.%) and moderate (15 wt.%) solids concentrations. Multiple particle-phase representing particles of poly sizes (75–1400 µm) and multi-densities (1450–2650 kg/m3 ) were simulated to study the particle segregation on the spiral trough surface. The numerical predictions are compared with the literature performance data at a diluted pulp flow rate of 6 m3 /hr. The results were found in close agreement. Further, the same CFD model is used to study the change in pulp velocity, streamflow rates, and separation performance at increasing solids concentration. For the same density particles, Fine particles mostly show higher volume concentration in the middle and outer trough regions, whereas coarse particles show higher volume concentration in the interior and central trough regions. It implies that the fine particles mostly segregate towards the outer region, and dense particles segregate towards the axial column.

Aug 24, 2022

At the beginning of the seventies pre- drainage of methane was introduced in West German coal mining in order to reduce the gas emission from the worked seam. After three pilot tests on the "Rheinland" Colliery (86 boreholes in seam "Prasident"), "Bergmannsgluck/ Westerholt" Colliery (23 boreholes in seam "Gustav") and "General Blumenthal" Colliery (27 boreholes in seam "Hugo" and 170 boreholes in seam "Karl") systematic large scale tests with extended investigations were carried out un the "Rheinland" Colliery (127 boreholes in the seams "Anna", "Blucher", Prasident"). During this time an analogous test was carried out on the "Consolidation" Colliery (21 bore- holes in seam "B"). In these studies and tests the technical feasibility, efficiency and economy could be proved, so that pre-drainage of methane starts spreading. On the "Rheinland" Colliery pre-drainage has become common practice in gassy seams. Mainly two points impede a faster spreading of method: 1. in many cases the necessary requirement, that one or both of the gate roads should ire driven 6 to 12 months before the face is worked, is missing. This is mainly due to the difficulty of retreat mining in passe seams.

Jan 1, 1982

THIS excellent volumetric method commends itself as a means of estimating the fineness of silver firstly, owing to the large number of possible impurities which do not affect its accuracy (these impurities include Cu-up to 70 % Au, Ph, Zn, Bi, Cd, Fe, Mn, Sb, and As); secondly, the method combines accuracy with speed. The above impurities are the only ones likely to be present in the B. H. A. S. Pty. Ltd. refined silver, and, with the exception of Cu and Au, the others, if present at all, would be well under 0.1 parts per 1000.Briefly stated, the method consists in the solution of the refined silver in HN03 , addition of ferric alum (indicator), and titration with an alkaline (either ammonium or potassium) thiocyanate solution until the brown ferric thiocyanate is formed, and gives a definite tint to the solution. The method is used at the Port Pirie smelters, and the outstanding feature in the method as there applied is the type of burette employed. This burette enables the operator to read 0.01 of a cc. with ease, whereas, with the ordinary burette fitted with a float, 0.05 of a cc., when a number of readings have to be taken, becomes very straining to the eyes. Moreover, waiting for the float to rise, and dislodging air bubbles from it, hinders rapid working.A description of the burette and fittings is appended with fig. 2. DETAILS OF THE METHODSolutions required are:a) Stock Solutions:(1) Ammonium thiocyanate, 40 grm. per litre of water; 30 litres are prepared and placed in a carboy with glass syphon attached.(2) Ferric alum, 250 grnl. per litre; two litres are prepared.

Jan 1, 1922

By R Thompson, J Miedecke, D Handel, E Tomicek, D Tulloch

"The Mine Haul Road Optimisation Alliance (HROA) is a unique Australian industry–academia collaboration that has been developed to support mine haul road operators. The alliance integrates industry, end-user service providers and academic research expertise in mine haul road design, construction and operation to identify, quantify, implement and monitor the various equipment, materials and road management strategies and solutions required to drive haulage productivity improvements.Initially, a broad overview of the university–industry collaborative landscape is presented, following which the current situation in the Australian mining sector is reviewed both nationally, and on a country-wide basis internationally. This insight places into context the opportunity that strategic collaborations present, to drive productivity and efficiency in mining, while also delivering innovative technology solutions.Following an overview of the HROA collaborative structure, aims and objectives, it is shown how academia and industry collaborations can deliver a more robust and needs-driven solution to mine haul road design, performance and management, especially where integrated solutions are needed. Critically in this approach, implementation and monitoring data provided by industry and service providers alike form the foundation on which to develop research knowledge and innovation that is more responsive to the end-user requirements, typically represented by ‘early goals’ and practical, implementable solutions.The paper concludes with examples of how the alliance collaborations work in practice to deliver focused mine haul road research outcomes, together with the mechanisms used to ensure industry needs are met through end-user driven research solutions for enhanced operational performance.Citation:Handel, D, Miedecke, J, Thompson, R, Tomicek, E and Tulloch, D, 2016. Driving Haulage Productivity Improvements through Industry–Academia Collaboration, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 243–252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

At the outset, I guess we should define what we mean by "com- modities". In the 20 minutes or so which I have for this paper, it is impossible to tackle all commodities -one would need to con- sider not only the base metals but also the ferrous iron and steel products as well as energy commodities such as coal, oil and even uranium. For the purpose of this address however, I would prefer to refer to the principal non-ferrous commodities: copper, lead, zinc, aluminium and nickel and, I would like to consider some of the changes which have taken place in the industry over the past 20 years-and the likely reasons for these changes. I would also like to dwell a little on the future and some of the key issues which-may influence the future path and direction of the metals industry.

Jan 1, 1988

By M Zanin, E Chan, D Xu

An experimental design has been developed to investigate the relative influence of distinct pulp and environmental properties on froth stability in the flotation of a typical porphyry copper ore. In particular, factors such as frother and collector type, feed particle size (P80), solids per cent, composition (chalcopyrite and pyrite content), as well as grinding environment (mild steel versus stainless steel, high and low pH) have been varied in a controlled manner, and the resulting froth stability evaluated. A previously developed froth stability column, based on the Bikerman approach, was used to measure the froth height and half-life in each test. The relative effect of each factor is presented here on a comparative basis. It is shown that frother type is the most important factor, with marked difference in froth stability when switching from methyl isobutyl carbinol (MIBC) to glycol based frothers. Solids per cent and particle size also play a significant role. The grinding environment had lesser effect on the resulting froth stability, although mild steel grinding gave higher froth stability compared to stainless steel grinding. The experimental evidence supports the hypothesis that in porphyry copper flotation the grinding environment influences surfaces oxidation, pyrite activation and the extent of hydrophobic particles reporting to the froth phase. This has an indirect effect on the resulting froth stability, which is however small if compared to the other factors. This work is still in progress, and extension to other mineral systems is planned. However, some insights are offered to operators on the parameters which are more likely to have an impact on froth stability in copper flotation plants.CITATION:Zanin, M, Chan, E and Xu, D, 2014. Empirical evaluation of factors affecting froth stability in copper flotation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 193–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By K J. Grohs

Martabe gold and silver mine is situated in northern Sumatra and comprises several deposits in steep terrain that are required to be developed in the optimal sequence for the best possible Net Present Value (NPV) return on the project. In addition, the waste from the excavations is a by-product to be scheduled and used for construction of the tailings storage facility (TSF). These plans need to be aligned to ensure the tailings can be contained relative to the production rate. The TSF embankment construction includes potentially acid forming (PAF) waste that needs to be progressively sealed and rehabilitated to meet the closure requirements of the future.The mine is situated approximately 3 kilometres north of the township of Batangtoru in a seismically active zone between the off-shore subduction zone and the trans Sumatran fault. The mining operation currently includes two open cut pits with a third in development stage, an integrated TSF and dualpurpose valley-fill type waste rock storage facility (WRSF) and TSF embankment. Mine waste is used in construction of the WRSF / TSF embankment, including PAF waste rock, which needs to be scheduled for optimal use in construction activities in a manner that mitigates future acidic and metalliferous drainage (AMD) risks (Pearce and O’Kane, 2017).The Life-of-Mine (LOM) plans must satisfy both optimal pit development to maximise NPV and suitable delivery of waste for effective TSF construction matching the rate of rise of tailings, and consider AMD management, progressive rehabilitation and ultimately effective sustainable mine closure. This paper outlines the methodology to optimise the system to deliver these potentially opposing objectives.CITATION:Grohs, K J, 2018. Martabe integrated life-of-mine optimisation, in Proceedings Life-of-Mine 2018, pp 83–86 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By B Murphy

Seeking to reduce the likelihood of uncontrolled personnel entry into the operating footprint of a dragline, Coronado Global Resources initiated a review of proximity detection systems currently available and equipment interactions in and around dragline operational areas. At the time of the assessment, there were no established personnel proximity detection systems in compliance with functional safety standards for large machinery in Australia. Our primary objective was to guarantee a functionally safe outcome, particularly by implementing a performance-level-rated system in accordance with AS4024 (Safety of Machinery series of Australian Standards). Applying appropriate detection technologies, the goal was to reduce the residual operating risk for machine-to-machine and machine-to-personnel interactions. A comprehensive analysis of available or in-development technologies was conducted, and a layered approach (demonstrated in Figure 1) was adopted to achieve the desired risk reduction by segregating the sensing zones into distinct areas using diverse and disparate technologies consisting of radar (short); light detection and ranging (LiDAR) (medium); and optical (long). To address the potential limitations of each technology, overlapping layered sensing zones were designed. With LIDAR and optical using two distinct artificial intelligence (AI) systems to classify detections, these were specifically trained to handle the unique environments of a mining operation.

Sep 1, 2024

By S J. Chen, N Jiang, Y S. Ding, F X. Li, D W. Yin, F Wang

This study assessed the deformation failure characteristics of rock-coal composites with different height ratios. Uniaxial compression tests were conducted using an acoustic emission monitoring system and XTDIC three-dimensional full-field strain measurement system. The results showed that with the increase in rock-coal height ratios, the uniaxial compressive strength of composite samples increased from 5.26 MPa to 14.61 MPa. The evolution of the deformation localisation zone of the composite samples is closely related to the initiation and propagation of the primary cracks in the coal samples. At the moment when the main fracture of the coal samples occurs, there is a large drop after the peak of the stress-strain curve of the composite samples, and the height of the rock samples increased to varying degrees, which indicated that the failure of the coal samples induced the rebound deformation of the rock samples. With the increase in rock-coal height ratios, the rebound deformation amount of the rock samples decreased from 0.042 mm to 0.008 mm, and the rebound deformation rate decreased from 0.210 per cent to 0.010 per cent. Meanwhile, the rock samples’ rebound deformation releases part of the elastic energy to act on the coal sample, further contributing to the destruction of the coal samples. Compared with single composite coal samples, the coal samples of the composite samples have much more failures. In addition, with the increase in rock-coal height ratio, the input energy density, elastic energy density, post-peak release energy density, and residual elastic energy density of the composite samples increased, the dissipation energy density decreased, and the percentage of pre-peak elastic energy density increased from 98.56 per cent to 99.86 per cent. These results revealed the deformation failure characteristics of rock-coal composite with different height ratios and provided a theoretical reference for understanding the underground dynamic rock failures.

Nov 29, 2022

By A Salama, J Greberg, B Skawina

In today’s underground mass mining, the orepass is an important part of the infrastructure as it connects two or more mine levels and is used for conveying or storing large amounts of material. One of the main risks related to an orepass is when operational or structural failure occurs, leading to long-term loss of functionality. Developing or rehabilitating an orepass when major failure has occurred is a time-consuming and expensive operation, and the risk of a long-term orepass loss motivates the development of alternative transportation strategies to ensure the continuation of smooth operations in large underground systems. The study presented in this paper has been done at the Loussavaara Kiirunavaara AB Malmberget mine in Sweden, where iron ore deposits are being extracted using sublevel caving. The study analyses the transportation system in one of the mine’s orebodies using discrete event simulation, with a focus on maintaining ore transportation in the event of the loss of an orepass.CITATION:Skawina, B, Greberg, J, Jonsson, K and Salama, A, 2016. Orepass loss mitigation approach in Malmberget mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 617–622 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Noller B. N, McGill R. A

The Alligator Rivers Region has been the scene of one of Australia's most intensive environmental monitoring efforts since the current generation of uranium mining was mooted in the 1970s. Prior to mining, the local environment and the nature of potential impacts were not well known. The initial monitoring programs therefore included large baseline characterisation and research components. After some 15 years, water, soil and sediment monitoring programs have been reduced to a fraction of their early size, as the mining and natural systems became better known and characterised, and the actual nature of the environmental impacts were established. Modem techniques allow much more rapid and thorough identification of chemical species and elements of concern, allowing much more focused monitoring programs to be designed. In the 1980s data collection was emphasised at the expense of interpretation, and monitoring programs were maintained at much higher levels than were in fact required. It is now clear that investigations are important and should be distinguished from monitoring programs, and that the timely interpretation of investigations and implementation of recommendations can greatly reduce the effort and expense that can be involved in a monitoring program. Monitoring programs based on a sound understanding of potential environmental impact may then be efficient and cost-effective, yet provide sufficient information to assess the environmental impact of mining, guide further environmental protection measures when problems are detected, and demonstrate compliance with regulatory requirements.

Jan 1, 1994

By K Baskaran, T McKenzie

Sustainability is becoming increasingly important in the mining and mineral processing industries and must incorporate the associated waste products. Acid mine drainage (AMD) is one such by-product and is one of the most serious environmental problems facing the minerals industry today. The oxidation of sulphidic mine wastes often continues for a substantial period of time after mine closure, resulting in difficult and costly remediation and rehabilitation works. Mining companies are often reluctant to spend increasing amounts of money on waste treatment when the mine life is limited or even finished. Hence a simple, low maintenance and low-cost method of treating AMD is required. Whilst this paper does not address the issue of AMD, it does propose methods for removal of individual species from AMD with potential benefits, including raising AMD pH. A novel concept of using biosolids as a biological adsorbent, or æbiosorbentÆ, of metals from AMD is being investigated at a laboratory/pilot scale level. Biosolids are a by-product resulting from the biological treatment of wastewater, and have been previously shown to adsorb metals from aqueous solutions. This could lead to an environmentally sustainable or ægreenÆ method for treating both AMD discharges and disposing/reusing the biosolids. The result of a laboratory-scale study of the biosorption of Zn(II) is presented in this paper. Physical parameters including reaction kinetics, mixing speed and solution pH were investigated. Solution pH also rose an average of 2 pH units over the 24 hour equilibrium time û a valuable side effect when treating acid mine drainage. The outcome of the study highlights the usefulness of biosolids as a biosorbent for the removal/recovery of metal ions from acid mine drainage. A simple, low-cost treatment technology requiring low maintenance would be beneficial to the mining industry to address some issues relating to AMD and would help integrate environmental and economic considerations into sustainable environmental management.

Jan 1, 2002

By D Connelly

High purity alumina (HPA) is a processed, premium non-metallurgical alumina product characterised by its purity level ie 99.99 per cent (4N) or 99.999 per cent (5N). The market price, application, and performance of HPA varies widely according to its degree of purity. High purity alumina is a form of aluminium oxide (Al2O3) with growing use in LED lighting and coating on the ceramic cathode separator sheets in lithium ion batteries. This paper describes a study on producing high purity alumina from feldspar to produce HPA and potash for use as a fertiliser. The project was positive for a number of reasons. High potassium extraction (>99 per cent) was achieved in the alkali leach using sodium hydroxide as the leaching agent and full dissolution of the alkali leach residue was achieved using hydrochloric and sulfuric acid. The potential to produce a high purity alumina product via a complex but promising emerging process was assessed. The potential to extract potassium as potassium sulfate to add value to the project was also demonstrated with the test work.

Sep 1, 2024

By Rowe J

The case study is based on the largest ore deposit at Mt. Lyell; the Prince Lyell deposit, comprising a regular lensoid mass of dissemina- ted and vein pyrite-chalcopyrite mineralisation. Reserve estimation employs conventional techniques, based on diamond drill hole and relevant development sampling data. Probable ore reserves are estimated using the contouring (isoline) method an longitudinal projections for ore thickness and accumulation (m %Cu) at a '0.8% Cu' cutoff. Final stope and pillar res- erve estimates (proved ore) are derived from designed ring tonnages and contoured accumula- tion for individual mining units, following more intensive sampling. Systematic grade control procedures have been adopted and individual stopes and pillars reconciled against mill production. The proved ore estimates have been found to com- pare favourably with the reconciled production.

Jan 1, 1979

By H Sichani-Teimouri, B N. Noller, J C. Ng, R N. Alsaadi, P L. Breuer, S Shini

Cyanide has been used for over a century worldwide for gold extraction. However, the presence of several metals and metalloids in ore requires greater amount of cyanide for an efficient gold recovery due to their solubilisation in conjunction with gold. The extraction residues are discharged into tailing storage facilities (TSFs) and may cause bird mortality if there is exposure to cyanide-bearing wastewater exceeding the toxic threshold. The toxicity arises from free cyanide released from weak acid dissociable (WAD) cyanide complexes. The International Cyanide Management Code (ICMC) has deemed 50 mg/L of WAD cyanide released into TSFs to be safe for wildlife protection. However, this concentration is based on observations of an apparent lack of toxicity rather than a toxicological approach. The National Industrial Chemicals Notification and Assessment Scheme (NICNAS) identified in 2010 that there is a lack of toxicity data to properly assess the environmental significance of cyanide levels at gold mines. Lack of knowledge for the toxicity of free cyanide and metal cyanide complexes to wildlife led to consider alternative direct assessment techniques for designating safe levels. Whilst toxicity may be assessed by using young chickens with animal ethics approval, the traditional bioassay approach to assess cyanide toxicity is impractical for gold mine TSFs. Bioassays using algal species such as Euglena gracilis, a unicellular alga, are widely used for ecotoxicological studies. A unique feature is that the Euglena gracilis Z cell has plant-like while SMZ cell has animal-like characteristics. The aims of this project are to evaluate the suitability of Euglena gracilis Z and SMZ strains to assess the toxicity of free cyanide and both strong (cobalt) and weak (zinc, copper and nickel) acid dissociable metal-cyanide complexes that may be present in TSFs.CITATION:Noller, B N, Ng, J C, Shini, S, Breuer, P L, Sichani-Teimouri, H and Alsaadi, R N, 2014. Development of a toxicity approach to evaluate free cyanide and metal cyanide complexes in waters associated with gold and other mining, in Proceedings Life-of-Mine 2014 , pp 573–590 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By A Karrech, C Schrank, O Gaede, I Canbulat

Strain-based failure criteria have several advantages over stress-based failure criteria: they can account for elastic and inelastic strains; they utilise direct, observable effects instead of inferred effects (strain gauges versus stress estimates) and they model complete stress-strain curves, including prepeak, non-linear elasticity and post-peak strain weakening. In this study, a strain-based failure criterion derived from thermodynamic first principles utilising the concepts of continuum damage mechanics is presented. Furthermore, implementation of this failure criterion into a finite element simulation is demonstrated and applied to the stability of underground mining coal pillars.In numerical studies, pillar strength is usually expressed in terms of critical stresses or stress-based failure criteria where scaling with pillar width and height is common. Previous publications have employed the finite element method for pillar stability analysis using stress-based failure criterion, such as Mohr-Coulomb and Hoek-Brown, or stress-based scalar damage models.A novel constitutive material model, which takes into consideration anisotropy as well as elastic strain and damage as state variables, has been developed and is presented in this paper. The damage threshold and its evolution are strain-controlled, and coupling of the state variables is achieved through the damage-induced degradation of the elasticity tensor. This material model is implemented into the finite element software Abaqus and can be applied to 3D problems.Initial results show that this new material model is capable of describing the non-linear behaviour of geomaterials commonly observed before peak strength is reached as well as post-peak strain softening. Furthermore, it is demonstrated that the model can account for directional dependency of failure behaviour (ie anisotropy) and has the potential to be expanded to environmental controls such as temperature or moisture.CITATION:Gaede, O, Schrank, C, Canbulat, I and Karrech, A, 2014. A strain-based failure criterion for pillar stability analysis, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 393–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Klenowski G, Gilmour G. A

The Metropolitan Water Supply, Sewerage and Drainage Board, Perth, has recently con- structed two major sewerage tunnels in the metropolitan area and a further one is under construction. These tunnels were constructed in sand, sandstone and limestone. The Tamala Limestone is a Pleistocene calcareous dune sand which now varies in com position from loose sand to cemented rock. Investigation techniques included surface mapping, auger and diamond core drilling, seismic refraction geophysics and mechanical testing. The variable nature of the ground caused difficulties in all aspects of the investigation, particularly in core recovery and seismic work. The Beenyup Tunnel, 2.25m in diameter and 3440m long was excavated with a Dosco TBM 1800 machine and shield with precast concrete Charcon Universal bolted segment lining. The Burns Beach Sewer Tunnel, 1.27m in diameter and 860m long was hand excavated with precast reinforced concrete lining pipes jacked continuously behind an excavation

Jan 1, 1981