Search Documents

Roof bolting with resin bonded bolts has been developed extensively in French coal mines. There are three aspects of this development: 1. The reason for and the care used in the development of roof bolting from use as a reinforcement in a classical arched roadway to use as the only support in roadways in ad- vance of the working face (the roadway being reinforced behind the face); 2. The problems encountered and studied, such as choice of boltable roadways and determination of the technical data in designing a roof bolting pattern; 3. Only because roof bolting has been controlled by safety rules, and especially by accurate measurement of strata behaviour, has this system of support been expanded aapidly in France since 1967.

Jan 1, 1971

By Lynch AJ, Musgrove NH

The behaviour of chalcopyrite and pyrite in the rougher-scavenger and regrind-retreatment circuits in the Warrego concentrator is discussed. The effects of change in xanthate addition on the separation of chalcopyrite and pyrite is described. The effect of the regrind mill on the (flotation rate of particles containing chalcopyrite and pyrite is discussed with particular reference to the importance of removing sub-mesh particles from the feed to the regrind mill.

Jan 1, 1975

By Wood P. D, Pettifer G. R

In the upper coal surface in the Latrobe Valley, craters known locally as fireholes have developed due to prehistoric coal fires. They can be several hundred metres across and up to fifty metres deep, and are now filled with overburden materials varying from hard baked clays to very soft lacustrine clays. In addition to reducing coal reserves, continuous mining operations are seriously affected by fireholes. Large undulations in the upper coal surface result in a mixture of coal and overburden on the upper mining levels. The very soft lacustrine clays are unstable in the mine batters and the overburden dump, are difficult to handle on the bucket wheel excavator/conveyer system, and have insufficient bearing capacity for the large bucket wheel excavators. Early identification is essen- tial and both drilling and dynamic core penetrometer have been exten- sively used. However, this has not proved adequate in locating and defining the extent of all fireholes, due largely to their irregular shape. To overcome this a range of geophysical techniques has been trialled with very promising results. A trial area has been covered on a twenty metre grid using gravity and Geonics EM34 conductivity measurements and the same area has been covered at a closer spacing with high resolution magnetics. Image processing of contoured magnetic, EM34 conductivity and residual gravity data has resulted in very good correlation with drilling data.

Jan 1, 1989

In the late 1970's Western Mining Corporation, Exploration Division considered the purchase of a major multi-element spectrometer as an adjunct to our existing atomic absorption spectrophotometers. The analytical work proposed for the unit included barium, uranium and rare earth elements from Olympic Dam, uranium, sulphur, vanadium and strontium on Yeelirrie type deposits, major element and whole rock analysis, multi-element analysis of samples from the laterite, chromium and manganese exploration programmes and tin and arsenic analysis. These were all analyses that were not readily or easily performed by flame atomic absorption or were where we expected that a simultaneous multi-element instrument would be an advantage. Also the turnaround times for the commercial laboratories was considered unacceptably long for some determinations. Other factors, important when considering the spectrometer were the ability to ensure confidentiality of results and the ability to assign our own priorities and not to have to rely on commercial laboratories. The two techniques considered were X-ray Fluorescence Spectrometry and Inductively Coupled Plasma Optical Emission Spectrometry. The decision was made in favour of the ICP unit for several reasons. The ICP fitted in with our existing methodology, ie samples digested for atomic absorption or colorimetric techniques would also be suitable for ICP analysis and vice versa. The technique was suitable for water samples and for major element analyses and for rare earth elements. X-ray fluorescence spectrometers were installed at the Kambalda and Belmont laboratories and would be available to us for routine checking and for elements not suitable for ICP analysis. The final consideration was price. ICP was considerably cheaper than XRF.

Jan 1, 1987

By Barnett J. C

The arid and semi-arid region of Western Australia occupies about two-thirds of the State equivalent to an area of about 1.8 million sqkm. Groundwater demand in this area has historically been linked to the pastoral andmining industries commencing with the gold discoveries in the Eastern Goldfields some 100 years ago. Substantial increases in demand have occurred in the past two decades initially as a result of nickel discoveriesin the early 1970's and more recently the rapid resurgence of the gold mining industry. Mineral exploration and development in the Great Sandy Desert at Telfer (gold) and Kintyre (uranium) and in the Great Victoria Desert at MulgaRocks (uranium) has also been accompanied by detailed groundwater investigations.

Jan 1, 1988

By Hang G, Hongtian X

In this paper, it is briefly introduced that China's Ordovician limestone confined-water menaces coal mining and Ordovician water is prevented and cured to secure the safety of coal mining. The theory of "Down-Three-Zones" is presented on the basis of research and practice in recent ten years. The concept of "Down-Three-Zones" of floor water-eruption is described clearly. Finally, the principle and method of applying the theory of "Down-Three-Zones" are discussed. 1. An Introduction of Damage: China is rich in coal resources. The conditions of coal field geology are quite complicated. There is an area of two million square kilometre of Karst limestone in nine million six thousand square kilometres of territory. The resources of underground water are rather plentiful, but this menaces coal exploration. Sixty percent of coal mines in China are damaged by limestone confined-water in different scales, particularly coal mines located the Carboniferous-Permian coal fields of the Ordovician limestone distribution area of Northern China. Because there is the 500-800 metre thickness of Ordovocian limestone and the well developed Karst containsl plentiful water, Karst water can have more than 100 Kg/cm pressure. Limestone aquifers have only distances of several metres or several decade metres to coal seam, Karst water can enter the aquituge and even the coal seam, large eruptions often occur. For example, a mine of 3 million ton production capacity had an eruption of 2053 cubic metres per minute. This is the largest confined-water eruption which has brought enormous economic damage and threatened the safe production of coal mining. Therefore, the prevention and cure of Ordovician water has immense advantage to the development of the coal industry. There are several decades experience in the prevention of Ordovician water-eruption in China. The prevention of Ordovician water-eruption has two kinds of plans. 1) dewatering and depression: it refers to dewatering of aquifers as roofs of seam and depression of aquifers as floors of seam in mining areas. 2) comprehensive prevention under the condition of having water pressure in aquiters. Due to enormous water, electricity, equipment and lots of other factors, the former isn't used extensively, the latter tits to China's actual conditions and is used widely. So-called comprehensive prevention under the condition of

Jan 1, 1988

Types of structure found in 'Jest Australian beach sands are described. Their recognition by geostatistical methods follows nth a discussion of the effectiveness of sampling patterns. Examples of structures are given, and an account of their effect on valuation procedures.

Jan 1, 1977

Drag pick roadheaders and continuous miners have been applied in the coal mining industry for several decades, having replaced drill-blast methods as the primary means of excavating coal and coal-measures strata. The generally harder rock types associated with metalliferous mining have precluded the use of such machines in the past, however, developments in machine technology and increasing labour costs and environmental constraints suggest that there are now likely to be applications suited to the method. Metalliferous mining engineers are generally unfamiliar with the machines themselves and with the fundamental criteria controlling rock cuttability. This paper gives an introduction to the machines and the controlling factors.

Jan 1, 1987

By Walker K, Burton RC

An outline of the ventilation and refrigeration requirements of deep South African gold mines is presented. This is followed by a brief description of the history of controlled recirculation in mines and the practical and economic benefits such schemes can offer. The potential hazard of a fire in a recirculation system is discussed.The major part of the paper describes the first large-scale field trial of controlled recirculation to be conducted in South Africa. Emphasis is placed on the monitoring system that was used for data acquisition during the trial, and also on a safety system designed to shut off the recirculation fans in the event of a fire.The paper concludes with a review of the latest development work taking place on recirc-ulation safety systems.

Jan 1, 1985

The application of methods using large diameter down holes has become an important facet in both the development and stoping operations of mines within the Aberfoyle group. Holes of up to 98 metres (vertical) and 78 metres (inclined) have been successfully used in stoping operations. A number of rises have been developed to meet ventilation, servicing and escape-way requirements. The most ambitious rise to date has been a..vertical 93 metre long by 4.50 metre square ventilation rise. Although some early problems were experienced, the ultimate successful completion of this rise has enabled the technique to be incorporated with confidence in future mining plans. This paper summarises experience in long hole rising techniques, their evolution from the original cratering concepts, and the approach to further development of these techniques.

Jan 1, 1982

By Seneviratne SP

The excessive displacement of the seam floor in headings (i.e. roadways) called 'floor-heave' is often experienced in the underground mines of the Southern Coalfield of New South Wales. Apart from interfering with the mining operations, the phenomenon could be detrimental to the stability of the pillars left for support leading to an unpredictable increase in the subsidence of the overlying strata. The latter could pose a serious problem, particularly in the design of partial extraction layouts of mining for areas where subsidence is to be controlled. The susceptibility of the floor of different rock materials and thicknesses in a given `panel and pillar' partial extraction geometry was examined by two- dimensional Finite Element Modelling of the displacements, stresses and failure zones around the excavations. The modelling, assuming elastic behaviour of the materials, indicated that the maximum vertical displacements of the floor increased substantially as the Young's Modulus of the material decreased to less than 7GPa and the thickness of the layer increased. The results also discount the possibility of a properly designed panel and pillar geometry in the Southern Coalfield of New South Wales being unable to adequately control surface subsidence through the pillar, or its core independently of the yielded ribs, penetrating the floor.

Jan 1, 1992

By Denholm W. T

The SMELT-2 package is specifically designed to perform on-line simulation of smelting processes. This paper describes its application to the simulation of continuous matte converting followed by reductive slag cleaning in SIROSMELT reactors. The matte, containing 50% Cu is assumed to be produced at the rate of 20 tph in a continuous matte smelting furnace such as an Outokumpu Flash Furnace, Noranda or Sirosmelt reactor. Two alternative fluxing strategies in the converter are examined, namely: ò conventional silicate slags, ò calcium ferrite slags, and the flow sheets associated with each strategy are discussed. A regular solution model is used in the present study to account for the variations in the activity coefficients of components in the slag.

Jan 1, 1989

By Webster SS

This paper uses computer modelling tech- niques to compare and contrast anomaly patterns obtained with fluxgate (vertical field) and proton precession (total field) magnetometers at typical latitudes in northern and southern Australia. The use of these modelling tech- niques is suggested as an aid to magnetic interpretation and field examples are included from Tasmania and the Northern Territory.

Jan 1, 1975

When lying over 200-250m depth, many seams and surrounding strata are gassy enough to create mining difficulties , particularly in highly productive longwalls as well as in their development headings. In addition to the gassiness of seams or stra- ta in the outgassing volume around working, the shape expansion and limits of this one influences much the intensity of gas emission. These charac- teristics of outgassing volume differ very much ac- cording to the permeabilities of the seams and strata encountered by their fracturation due to mi- ning. Moreover, the shape of the outgassing volume is very much modified by the rate of advance of the face. In nearly impermeable deposits, gas flows from a limited outgassing volume. When the rates of advance of a face are medium or low, the shape and dimensions of this volume do not change very much and outgassing volume is translated progressi- vely with the face advance. This explains why, in the past, it was observed that there was for each seam an average steady specific emission of gas, round which the volume of gas evolved per mined ton or per mined unit area, calculated over a cer- tain time, was oscillating. Combined with a statisti- cal irregularity coefficient, this allowed prediction gas of emission and thus to take decisions for air ventilation, drainage, and eventually production.

Jan 1, 1988

Underground space can be defined as space below natural ground level which can be used as an alternative to an above ground location. While many of our above ground structures inherently involve underground excavation for foundations and services, the term underground space specifically refers to organised development of underground openings and of the underground domain. For example, the services to a city such as power, gas, sewerage, water and communications are installed in a congested array which usually requires roads to be dug up when the services need to be accessed. An underground space installation of services would involve a well planned conduit which is easily accessed without any excavation. The concept of using this virtually untapped land resource to the advantage of our expanding cities is gaining considerable interest in Australia. Overseas, in the Scandinavian countries and some Asian countries, underground space has been used for centuries; in Great Britain, France and the United States of America over the last century and in Japan for over a decade. This paper focusses on the types of underground space usage which should be competitive with above ground use and suggests areas in which the competitive edge may be improved in favour of underground space. In particular, considerable advantage is seen by using well-planned underground space developments in major cities, where the strategic central location of the development takes advantage of proximity to potential users. However, the largest single factor affecting the acceptance of underground space is the high capital cost of construction, even though an underground space development may result in lower operating costs and reduced long-term maintenance costs. While excavation methods and associated costs are very much site-specific, the importance of applying the latest technology in rock breakage, with consideration of ground vibration, excavation rates and ground support, remains a major challenge to the development of underground space.

Jan 1, 1995

This paper outlines the manner in which legislative control for tunnelling and allied operations has evolved, detailing Victorian experience. It examines the concept of mine managers as it relates to the industry and attemps to illustrate its benefits. The Victorian experience in relation to fatal and serious accidents is examined in detail, particularly in the allied art of trenching and examines the Krings system of trench lining support which is hoped will catalyse an increase of engineering expertise in this area. The paper concludes by demonstrating that safety awareness is not incompatible with production efficiency or economic viability.

Jan 1, 1981

Both safety and productivity in underground gassy coal mines can be improved substantially if an appropriate gas management system is introduced. A strong direct relationship exists between the gas emission rate, roof and floor strata relaxation zones characteristic, mining activities and gas drainage practices. Detailed knowledge of geological factors, gas and coal-rock properties, as well as mining systems are necessary for the methodology used in predicting overall underground gassiness, and planning gas capture and ventilation systems. Early gas emission calculations for various mining activities, particularly for the longwall mining system are essential. A reasonably accurate prediction of gas make as well as the design of ventilation, gas recovery (drainage holes) techniques can be made using 'Floorgas' and 'Roofgas' computer simulations, provided sufficient geological, mining, and gas data are made available.

Jan 1, 1998

Dartbrook mine is a new greenfields thermal coal longwall mine located n the Upper Hunter Valley ten kilometres north of Muswellbrook Figure 1). Construction began in April 1993 with coal extraction starting n October 1994. Longwall production is scheduled to commence in the first quarter of 1996 with production expected to exceed 3.5 million onnes per annum. The permanent workforce will number 150 full-time ,mployees and productivity rates will be 22 000 per employee per annum m a ROM basis. Being a greenfield site Dartbrook has had the opportunity to develop and operate the mine using the best practices and latest technology available to meet high standards of safety, quality and production.

Jan 1, 1995

By Mitchell D

In recent years the need to provide increased ventilation to improve environmental conditions rather than to dilute firedamp has led to increasing interest in the use of recirculation. Present UK mining law prohibits recirculation in ventilation, but it has been permitted selectively by exemption granted by Hm Inspectorate of Mines and Quarries. The conditions of use imposed by these exemptions to safeguard the safety and health of miners are examined in detail, dealing separately with primary and auxiliary recirculation systems.

Jan 1, 1988

By Sandvik

Fine grinding in an air-swept ball mill working in closed circuit with a forced vortex air classifier has been investigated first in continuous laboratory and then in industrial scale. Results from the laboratory circuit have shown significant influence of mill load (powder filling) on the capacity of the circuit. In laboratory scale the mill load was measured and controlled by a weighing platform placed under the complete mill set-up. The mill load of the industrial air-swept ball mill has till now been controlled by measuring the power consumption of the mill motor. Thus, it was necessary to operate far from the range of optimal mill filling. To improve the circuit performance, alternative ways of mill load measurement were investigated. An important factor was investment cost, as many fine grinding mills operate in relatively small circuits that do not wan-ant large investment. In this case the task was accomplished by using a piezoelectric strain transducer, which detected strain changes in the mill shell. It was installed in the midpoint of the shell, where the highest deformation was obtained. As the transducer was on the top position, it indicated compression, and on the bottom position it measured tension. By taking the difference between the readings, it was possible to calculate total strain variations, directly proportional to the mill load. The signal from the transducer was sent to a control room via a cordless infrared communication system, employing a microprocessor control card, which could further regulate other operating parameters of the circuit according to the software model. The installation required very low investment cost and provided simplicity of application as well as stability and reliability of characteristics under severe industrial condition. The measurement system made it possible to optimise the mill load and thus increase the production from 3.2 to 3.7 dh (15 per cent), and stabilise the circuit operation.

Jan 1, 1995