Search Documents

By Robins R. G

The dissolution of metallic copper powder in aqueous solutions of cupric sulphate under the influence of ethylene gas was investigated. The dissolution reaction stoichiometry obtained was: Cue+(aq) + Cu(s) + 2C2H4(g) = 2(CuC2H4)+(aq) The rate of formation of the copper (I)-ethylene complex in the above reaction was studied in a laboratory autoclave and the effect pH, temperature, ethylene partial pressure and initial concentration on the dissolution rate was measured experimentally and expressed theoretically in terms of several simple conceptual kinetic models. The results led to the selection of optimum conditions for the reaction and the suggestion of an "ion-molecule reaction" mechanism to explain the very low activation energies for the reaction system. The area of application of this reaction lies in the direction of refining impure copper such as cement copper. Several experiments were performed in which an acidified solution of cupric sulphate under ethylene pressure was used to dissolve copper from the cement copper powder in the form of the copper (I)-ethylene complex, followed by the release of gas pressure to disproportionate the complex and precipitate a purer metallic copper.

Jan 1, 1987

Mineral exploration is the business of finding and defining ore deposits. Ore bodies are developed into mines and mines supply every mineral and metal upon which our society is built. Whether it be steel for our bridges, cement and aggregate for our concrete, coal for our power stations, copper for our wire, phosphate for our fertiliser or gold for our jewellery it first must he found, then mined and processed before we can use it. There is no other way.

Jan 1, 1993

By C J. Moran

The Gladstone region, as one of the most industrially intense regions in Australia, uses significant quantities of fresh water. Awoonga Dam, situated on the Boyne River, is the only major source of water in the region. The current typical annual usage is 53 GL (Porteous, 2006) and approximately 80 per cent of the water is used by heavy industry (Gladstone Area Water Board, 2004). Until relatively recently, there has been ready and easy access to raw water for industrial use. The recent drought, which resulted in severe water restrictions in 2002 and 2003, emphasised the importance of water for a dominant industrial region like Gladstone. Although now in the process of changing, the typical contractual arrangements in the past have provided little financial incentive for efficient water use. From research undertaken on potential water reuse opportunities, several key questions have emerged related to water management in an industrial region such as Gladstone. This paper highlights these key questions, presents findings from recent regional strategies and assesses the potential for water reuse. Even though there is no clear-cut financial incentive for reusing water, there could be stronger regional and risk mitigation drivers for doing so. Initiatives to incorporate adaptive capacity through collaborative industrial synergies would allow for robustness and resilience in water security, leading to long-term sustainable water management across the Gladstone region.

Jan 1, 2006

HAPPENING to be in Cue recently the writer was unexpectedly called upon to make surveys of some diamond drill bores on the Big Bell mine on the Murchison goldfield. The owner of the mine Mr Herman Mandelstam. had brought such apparatus with himas he could lay his hands on. and no other was available without prohibitive delay.The usual method of making these surveys as is well known is by putting a glass tube half filled with gelatine or glue in a melted state down the hole with a small magnet freely suspended in the glue and having it there till the glue sets solid. When this tubeis withdrawn (its depth down the bore being noted) the bearing and inclination of the borehole at this particular point can be read - the bearing by the compass and the inclination by the angle between the tube and the surface of the glue which of course ishorizontal. By taking a number of these observations according to the degree of accuracy required the course of the bore can be fairly accurately plotted.In dealing with dry holes there is little trouble but when the holes are full of water great difficulty is experienced. In the case in point the first observation was made in water 300 ft. deep, corresponding to a pressure of 130 lb. per sq. in. The tube containing the gelatine and glue (a mixture was used) was found, when hauled to the surface, to be completely filled with a weak mixture of water, gelatine, and glue and there was no horizontal surface from which to measure the angle of inclination of the bore. The water had been forced through the corks and sealing wax with which the tube had been closed. After several attempts it became obvious that no method available would keep the water from getting into the air-space in the tube, and to a pressure-proof metal container was impossible, nothing remained but to do away with the air-space and this was accomplished by using two liquids of different specific gravity - mercury and melted glue. The tube...

Jan 1, 1930

The effectiveness of three different types of longwall chock under the three different types of geological conditions worked recently is outlined. Some provisional analyses of the variation of chock load under the shale roof con- dition are briefly discussed and some problems and solutions of gateway and road- head support outlined.

Jan 1, 1974

Many problems result when coal mine shafts are built in complicated geological conditions and serious shaft lining ruptures have often occurred in the eastern part of China since 1987. Grouting is applied as one of the major measurements for shaft lining ruptures. However, as the general location of reinforcement grouting for shaft lining is deep in or near the bottom aquifer, while using cement grout as the grouting material, the grouting mostly belongs to fracturing grouting in deep alluvium. In these conditions, the mechanism and behavior of fracturing grouting has not yet been understood. From these points of view, this paper describes the mechanism of shaft lining rupture and fracturing grouting and then discusses the effect of grout injection on the stability of shaft lining by means of numerical analysis and field data obtained so far.

Dec 6, 2010

By Hart J. G, Anderson J. S

The presence of platinum metals in the nickeliferous copper ore of the Thomson River Copper Mine near Walhalla, Victoria, was first revealed in 1905 by assays made in the laboratory of the Department of Mines (1).These disclosed the presence in the ore of 5 dwt. platinum metals, 1 dwt. gold and 13 dwt. silver per ton. Attempts to isolate the platinum-bearing mineral were unsuccessful, and the absence of obvious native platinum led the assayer, Mr. P. G. W. Bayley, to suspect that the platinum might be present as sperrylite. Subsequently, Mr. C. M. Lyons, then metallurgist to the Long Tunnel Gold Mining Company, Walhalla, tried to isolate the platinum mineral from samples of ore containing as much as 7 dwt. platinum metals, but again without success.In 1912, a sample of copper matte from this ore was submitted to Messrs. Johnson, Matthey and Company, Limited of London, for analysis. The analysis, which is quoted below by their courtesy, revealed tnat a large proportion of the metal pi'eviously reported as platinum was palladium, there being about two parts of palladium in the matte to one part of platinum.

Jan 1, 1942

By Stone AM, Romensky G

The requirement for economic operation of unit trains carrying bulk materials has dictated that rapid and accurate bulk loading methods be provided. The train loading station at Phosphate Hill, built for Queensland Phosphate Ltd. to load rock phosphate, provides this facility and whilst the concept used is not unique, it contains a number of novel features that are considered to advance the "state of the art'' in this field. This paper briefly reviews some alternative concepts evaluated, and describes the design and operation of the scheme ultimately selected as being most appropriate to the project requirements. it is one which utilises a variable speed belt feeder whose speed is controlled in proportion to the weight rate of material moving on the belt as measured against a set point

Jan 1, 1978

By R Morrison, P Walters, B Adair, V Jokovic

‘Grade Engineering<sub>®</sub> is an integrated approach to coarse rejection that matches a suite of separation technologies to ore specific characteristics and compares the net value of rejecting low value components in current feed streams to existing mine plans as part of a system-view’ (Walters, 2017). Two of these technologies are directly recoverable through screening stages: Natural Deportment and Induced Deportment. The potential for taking advantage of “Natural Deportment” by size following blasting and crushing has been demonstrated for a range of ore types. Simple and low cost screening can in some cases generate a fine product with improved grade and a lower grade oversize which can be directed to leach or to waste. Where an ore body consists of many different ore types, the traditional approach of blending to metal grade will often add to complexity of treatment, which will reduce the effect of “natural deportment” by size.CITATION: Jokovic, V, Walters, P, Adair, B and Morrison, R, 2018. Applying enhanced grade engineering to complex ore bodies, in Proceedings Complex Orebodies Conference 2018, pp 21–23 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By D J. Robinson, L L. Kuhar

In-situ recovery (ISR) is accepted and applied across many geographies, and approximately 50% of the world’s uranium is currently extracted by using an ISR method (World Nuclear Association, 2014). The low environmental impact, the elimination of risk for mine workers and the fact that all of the lowest-cost producers of uranium use an ISR approach should raise interest from traditional miners (IAEA, 2014). However, the broader application of ISR to other commodities and mineral systems remains limited. A number of demonstration (experimental) copper projects have been undertaken (Sinclair and Thompson, 2015) with a few copper projects in Arizona being close to demonstration (Florence, 2018 and Gunnison, 2018). Evidence of very few economically operating ISR copper projects can be found (for example, the Russian, Uralgidromed OAO, built by the Russian Copper Company in 2005 and operated as an ISR facility from the Gumeshevskoye deposit (Russia Mining, 2018). A number of gold deposits, particularly paleochannel deposits, have also been considered for ISR, but, to the best of our knowledge, only limited demonstration and no commercial operations have been established, yet (Kuhar et al, 2018 and references therein).CITATION:Robinson, D J and Kuhar, L L, 2018. Extending mine life through application of an in situ recovery approach, in Proceedings Life-of-Mine 2018, pp 56–57 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

The story of the rise, progress, and development of our modern railway system is a long but an exceedingly interesting one. The phases it has passed through, the discussions that have arisen from time to time on the most economic modes of construction and working, and the final result these various discussions have led to, are full of importance and interest to the engineer. It is not my intention to deal historically with the subject. I desire simply to speak to the requirements of the hour in Australia. It will not be disputed, I think, that these colonies have reached a point in railway construction and management when, if additional lines to any extent are still to be built, a different principle must be adopted. There are yet large tracts and areas of country to be tapped by the rail and the locomotive, which for years to come must remain untouched if the same expensive gauges and modes of construction are continued. We have yet to see clearly the necessity of introducing a system of light lines that will pay their own way and at the same time augment the traffic of our main lines. This question really no longer remains an unsolved problem. It lies, in a few words, in the acceptance of the, narrowest gauge and the simplest mode of construction that can constitute a pacticable railway. I fear it is hopeless to suggest that private companies should be legally permitted to construct such lines. It seems as if it were next to impossible to move official authorities to enter upon the construction of lines on this principle. It is, all the same an undoubted fact that if private companies could obtain Acts of Parliament, that in several of the colonies a new impetus would be given to railway construction.I may point out that not only has the principle of narrow gauge light railways been adopted in India but private companies are obtaining power to build them. Outside of :England many narrow gauge lines have been made, and in France, Denmark, Italy, and Sweden they have been highly successful.

By R Berry

This paper looks at two ways to estimate the bulk mineralogy of the rocks for assay intervals. The aim is to find an efficient indicator of the most common minerals in the rock. Phase (modal) analysis has traditionally been done using visual methods such as point counting and image analysis. A modern version of this process is the X-ray point counting routine using the SEM-EDS based software. These methods are too slow and expensive for routine analysis of bulk sample mineralogy at the normal assay spacing.Two sources of data were considered that provide information that can be used to determine the mineral abundance in assay samples. The most widely applied method is (semi-) quantitative X-ray diffraction (QXRD). The QXRD method is most applicable to major minerals and has limited application to minerals at low abundance. The nominal detection limit is 0.5 per cent. Values below five per cent have large errors. A second, less common, method is calculation of mineralogy from chemical assay data. Conversion of chemical analyses to mineralogical analyses depends on the unique chemical composition of each mineral. Elements only found in one mineral are easily accounted for, but many compositions are ambiguous. Deciding on the actual mineralogy is not simple. Recalculation of mineral mode from chemical analyses is more accurate than QXRD when the correct minerals, and mineral compositions, are known.Where only a few QXRD analyses are available they can be used to setup a protocol for calculation of mineralogy from assay data. Linear programming works well in this environment. The best results are obtained when both H2O and CO2 are directly measured. Loss-on-ignition (LOI) should be included if these are not available.Where both QXRD and chemical analysis are available for all samples, the best results are obtained using the least squared method to merge the data sets assuming QXRD has much higher analytical errors than chemical assays. The combined method provides more robust results because the high abundance minerals are controlled by the QXRD measurements while the chemical assays improve the precision for low abundance minerals

Sep 5, 2011

By H R. Watli, K L. Davies, J A. Johnson

Novel microbial isolates that readily oxidise iron and sulfur were recovered from samples collected from a spent chalcopyrite/pyrite test heap. Methods were developed to enrich and isolate microbes that thrive in low pH environments and utilise iron and/or sulfur as sources of energy. Screening of these isolates revealed diverse substrate utilization (sulfur, ferrous ion, chalcopyrite, pyrite, glucose) as well as growth at temperatures between 30 - 50¦C. When native isolates were employed, shake flask leaching tests of chalcopyrite concentrate resulted in higher copper yields in comparison to laboratory reference strains Acidithiobacillus ferrooxidans (DSM 583) and Sulfobacillus thermosulfidooxidans (DSM 9293). After 700 hours several native isolates had leached between 20 - 30 per cent more copper than laboratory reference strains during experiments conducted at 45¦C. This research has established a unique culture collection of mining microbes that readily adapt to Australian conditions. Exploitation of these microbes may result in improved leaching kinetics and copper recovery from Australian chalcopyrite ores as demonstrated from shake flask leaching tests. Whilst this research provides a capability for Australian mineral sulfide ores, this technology can be easily adapted to suit ores of any origin resulting in more effective and efficient microbial leaching.

Jan 1, 2004

By R Steinhaus, D M. Frantois-Bongarton, P W. Cleary, G K. Robinson, M D. Sinnott

Multotec Process Equipment and Dominique Frantois-Bongarton have a patent for a mineral sampling device, which they call a æTrue-Belt SamplerÆ. This uses a plough, which is rotated about an axis parallel to a conveyor belt to throw material off the belt. A fixed sample cutter takes a sample from the material thrown off the belt.Discrete element modelling has been used to consider a range of plough designs, plough speeds, positions for the cutter relative to the plough, cutter apertures, cutter designs and frictional properties, prior to the building of a physical prototype. This modelling work will be discussed, both as an illustration of the role of modelling in the development of new materials-handling devices and in order to explain the likely strengths and weaknesses of this new type of sampling device.CITATION:Robinson, G K, Sinnott, M D, Cleary, P W, Steinhaus, R and Frantois-Bongarton, D M, 2012. Modelling of a ætrue-belt samplerÆ - A new device for sampling from a conveyor belt, in Proceedings Sampling 2012 , pp 33-40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By Daziel M, Corke P

Unit cycles in mining have not changed for many years. Productivity increases over the past three decades have mainly been achieved by using larger and heavier machines. This investment in size has probably reached the point of diminishing returns and increased productivity in the future will have to be generated by other means. One way of achieving this is through automation of selected unit operations, eg dragline overburden removal, truck haulage, ground support installation and secondary breakage. Although, in the past few years, there has been significant progress in this direction, we are still a long way away from even partial automation - especially in hard rock mines. This paper addresses the technical obstacles facing mining automation; suggests ways by which these obstacles may be overcome and identifies the role of industry groups and research providers in this process.

Jan 1, 1997

By J King, T Hunter, R Coleman

"The industry that supports operations and new projects is suffering a rapid decline in the currently severely curtailed capital investment environment. This is evidenced by a decline in the number of skilled teams, who are now centred in fewer locations. Other features are an aging and retiring ‘Baby Boomer’ generation, coupled with a low uptake of new graduates and the uncertainty in predicting future capital expenditure programs and requirements. Combine this with a reluctance of cash-poor operations to modernise and adapt in an environment of low metal prices, and there is a real uncertainty in how service providers will meet industry needs as they evolve.The industry that supports operations and new projects is suffering a rapid decline in the currently severely curtailed capital investment environment. This is evidenced by a decline in the number of skilled teams, who are now centred in fewer locations. Other features are an aging and retiring ‘Baby Boomer’ generation, coupled with a low uptake of new graduates and the uncertainty in predicting future capital expenditure programs and requirements. Combine this with a reluctance of cash-poor operations to modernise and adapt in an environment of low metal prices, and there is a real uncertainty in how service providers will meet industry needs as they evolve.Trends amongst service providers will be put forward as well as developing options and alternatives. These embrace a whole gamut of agile alternatives in the areas of partnering, alliances, commercial and shared risk models and mutual innovations. These will be discussed with some case studies and suggested approaches.Particular emphasis will be upon brownfield expansions and upgrades which have emerged recently as a preferred lower capital and focused way to achieve best practical outcome at lowest cost. There are a number of specific features of such brownfields projects including the requirement for very close cooperation between the execution team, operators, maintenance and suppliers and a maximum usage of site resources and ingenuity. Often, required investment hurdle rates are high, downtime allowed is minimal and site resources usage is maximised. This requires mutual trust, good planning and high health, safety, environment and community (HSEC) standards and practice. In many ways the practices and skills needed are the exact opposite of the historical ‘big greenfields’ project with which the industry has been geared for more recently.Another developing area has been with innovative commercial models and practices. These have been as a direct result of the more challenging investment criteria being adopted and the relative hunger of service providers. It has become more common to look at these commercial/costing alternatives very early in the project cycle as an essential project tool and not just as a possible option. These commercial solutions cover such alternatives as leasing and rental, deferred payments, build–own–operate–transfer (BOOT) and build–own–operate (BOO), whole-of-mine preferred spares and maintenance terms, and aggressive performance targets with real assurance penalties. Once again this requires very close mutual dealings and trust, and sufficient time allocation compared to a conventional approach.Citation:Coleman, R, King, J and Hunter, T, 2016. Upgrades, Modernisations and Expansions... Where Will the Expertise, Capability and Skills Come from in the Future?, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 69–76 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

This address is set deliberately in the broadest possible terms. A review of the place of mining in Australian life today will serve to point up the changes that we can see in the life of people in the industry. Some of the influences on the future welfare of mining people bear also on the progress of this Institute, now approaching its 90th year. As mining becomes more and more dependent on higher technology and therefore, on the higher skills of the people in the industry, the role of The Institute, I suggest, becomes more and more significant.With investment per employee in mining generally continuing to rise, our ability to handle problems of manpower and human relations becomes a matter of greater importance.Questions that flow from these general thoughts form the substance of what I have to say.

Jan 1, 1982

By P Audet, D R. Mulligan, D Doley

This analysis attempts to reconcile existing ecological theories, rehabilitation planning goals and implementation constraints in the form of a rehabilitation paradigm that considers potential and pragmatic ecosystem transformation pathways. The framework prioritises multiple developmental scenarios for post-disturbed landscapes within a continuum of ecological outcomes. A feature of the framework is that ænovelÆ ecosystems and agro-ecosystems, having a range of commercial and societal values, are valid outcomes spanning the conceptual divide between the ecological functions of under-rehabilitated versus re-instated ænaturalÆ landscapes, especially in a changing environment. Landscape suitability analyses are considered to be fundamental to the incorporation of regional landscape and climate in the implementation of land rehabilitation and management strategies. Altogether, the paradigm could facilitate the identification of widely pertinent rehabilitation goals having direct implications at the regional scale of restoration ecology and acceptance of the need for ongoing commitment to the management of disturbed environments.CITATION:Audet, P, Doley, D and Mulligan, D R, 2012. Can ænovelÆ ecosystems offer suitable rehabilitation alternatives for post-mined landscapes?, in Proceedings Life-of-Mine 2012 , pp 135-142 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

To explain in any depth the industrial relations of Broken Hill I believe that it is necessary to trace some of the many happenings that created the present industrial climate. While appreciating that our relations with the local industry are relatively good, it must be pointed out that to preserve and improve this present situation a duty is owed to everyone connected with the industry (workers, share- holders, etc.) by management and unions to see that just and reasonable agreements are found for any disputes. If the companies ever take the local position for granted it would soon die, killed by someone who may get some short term benefit, but who would lose something of incalculable worth in the long run. Similar- ly if the unions were to adopt some of the "wild cat" methods adopted in other parts of

Jan 1, 1975

By J Centofanti, D Conti, R Riske, C Morley, A Cook

Why is it so difficult? Why are there differences throughout the resources industry in how reconciliation factors are reported and calculated? Why is there no standard formula to use? These are common questions asked when mining companies try to compare reconciliation results across operations or attempt to undertake internal or corporate governance reporting processes. For many mining companies the calculation of reconciliation factors is often a very time and resource intensive part of mandatory reconciliation reporting. Some major mining companies, that move millions of tonnes of material per annum, dedicate full time resources to the calculation of reconciliation factors. The willingness of these companies to set aside resources demonstrates the value that operations place on good reconciliation reporting. Reconciliation is about measuring the variance between two like measures at different points along the mining sequence. It can be undertaken between predictive models, forecast plans and actual measured performance. Calculations are used to derive a variance between two sections within the mining sequence, with the result being commonly known in the resources industry as a æfactorÆ. Mining companies use the calculation of reconciliation factors as key performance indices (KPIs) to provide a æhealth checkÆ of their operation, with variances often pointing to issues either with the accuracy of the original estimate or the quality of the measurement being used in the comparison. There are many reconciliation factors that can be calculated and reported. This paper will set out, clarify and provide a recommended standard means of calculating each specific factor that, where adopted by a company, will ensure compliance with the international reporting codes, such as JORC. Using case studies from Rio Tinto Group (Rio Tinto) and BHP Billiton Mitsubishi Alliance (æBMAÆ), and the authors experience across a wide range of mine sites, the outline of a generic solution for tracking a parcel of material from the pit through to the port along with appropriate reconciliation factors is provided. The intention of proposing standardised reconciliation factor terminology and methodology is to provide the foundations of a system to enable communication and comparison across different commodities, companies and mines sites.

Jan 1, 2009