Search Documents

By Ueki S

Underground coal gasification (UCG) is a promising process for obtai- ning energy from coal, which is either unmineable with current mining techno- logy or uneconomic to recover, using conventional methods, in the present energy market situation. There are several coal fields, which could become new coal reserves, if the UCG process were successfully applied. In the 1960's Japanese researchers made a number of basic studies and field tests into UCG, although not all of them produced favourable results. This paper reviews Japanese research on UCG. This includs basic studies into coal gasification using a small, tube reactor fed by air and oxygen, and also large scale model stu- dies(reactor size of 8.Om x 2.4m x 1.5 m). Field test results from Akabira colliery in Hokkaido and a feasibility study of power generation using UCG from a coal field in Hokkaido are also Presented.

Jan 1, 1987

An established method exists for the computation of rope lifetimes for shaft hoisting applications in the mining industry. In an earlier study, during the 1990s, an initial comparison of the calculated and actual rope life for various types of hoisting plants showed reasonably good correlation. In the meantime the calculation method has been developed further. The rotation behaviour of the rope during hoisting and the effects of multilayer spooling on drums are now considered in the assessment of expected rope lifetimes. The ability to determine an estimate of rope life in advance is particularly useful for mining companies. Such analysis allows them to predict the effects of rope choice in their particular application and thereby reduce the total cost of rope ownership. Such calculation techniques also allow designers of winding plants to identify aspects of the hoisting configuration that may negatively affect rope life. Often small (low-cost) changes, like increasing the diameter of head sheaves, can result in considerable improvements in rope performance. This paper describes the extended lifetime calculation method and gives further examples of the comparison between actual and calculated rope lives for operational double-drum mine hoists.

Jan 1, 2005

By J E. Eberhardt

Ore sorting has long been used to raise the efficiency and thus lower the environmental impact of mineral processing operations. It was first instituted as hand sorting, according to a humanly perceived difference in the ore, but is now automated using large mechanical sorters in order to meet the high tonnage throughput required in most minerals processing applications. In the past, ore sorting was generally used as a niche processing route when other approaches failed, and in this context, consequential environmental benefits are often not the first consideration in adopting sorting. When applicable, ore sorting offers environmental benefits in reductions in fines waste, reagent usage and energy consumption in milling. Although there are significant opportunities for the use of ore sorting technology in many minerals processing operations, industry applications, to date, have been limited mainly to the processing of diamonds, magnesite, talc and uranium ores. This limitation has principally been due to a lack of suitable sensing technologies for a wide range of ore types. The authors report on a wide-ranging review of the automated sorting of mineral ores, and in particular, on methods for discrimination of ore characteristics prior to mechanical sorting.

Jan 1, 2002

This paper documents the relationship between material handling and processing costs compared to blasting cost. The old adage, 'The cheapest crushing is done in the pit', appears accurate in this case study. Comparison of the accumulated cost of powder, selected wear materials and electricity, indicate a strong, inverse correlation with powder factor (lbs powder/long ton of rock). In this case, the increased powder cost is more than offset by electrical savings alone. Measurable, overall costs decline while shovel and crusher productivity rise by about five per cent when powder factor rises by 15 per cent. These trends were previously masked by the effects of weather, ore grade fluctuations and accounting practices.

Jan 1, 1995

The conventional approach to the disposal of fine coal mine tailings, which involves piping the tailings as an aqueous slurry to a storage where they remain in the form of a permanent wet deposit, is becoming unacceptable. This approach is a legacy of a "contain and forget" mentality, which has economic advantages only in the short term. In the longer term, wet tailings deposits occupy large areas of land and present extreme rehabilitation difficulties. Alternative tailings disposal systems, which are sustainable and which facilitate rehabilitation, are required. The possible alternatives include the mechanical dewatering of fine tailings prior to disposal in combination with coarse reject, tailings disposal into spoil pile valleys, and the combined pumping to disposal of tailings and coarse reject. The most appropriate choice of fine tailings disposal strategy will vary from mine site to mine site. The chosen strategy should be optimised to meet increasingly stringent environmental requirements, within the constraints imposed by each mine. The alternative approaches represent significant departures from past practices, and require considerable industry driven research and development before they can be adopted with confidence. All three alternatives involve mixing of the fine tailings and coarse waste streams, aimed at creating a mixture of reasonable engineering properties. Understanding the engineering behaviour of such mixtures is central to the success of these alternative disposal strategies.

Jan 1, 1991

By S La Brooy, C Fountain

Throughout its history the mining industry has focused on the highest-grade deposits sited in the most convenient locations. The burgeoning global population and higher standards of living not only increase the demand for mineral products but also make it harder to mine and process them. The future will include the development of lower-grade, more complex orebodies, and orebodies in difficult locations. The industry will be expected to provide for humanityÆs needs while reducing its environmental footprint and maintaining profitability. This paper reviews some of the likely adaptations in mineral processing that will occur over the next 20 years. The challenges inherent in adapting to lower grade and more complex materials might be exacerbated by such factors as the availability of water and low-cost energy. In underground mining, higher energy costs are likely to foster further developments in underground preconcentration, especially for ores that can be upgraded at relatively coarse sizes. The adoption of underground crushing could also render material amenable to semi-dry preconcentration options such as might be achieved by the rotary classifier developed by CSIRO and being commercialised by RCR Tomlinson, or more modern versions of the hand-sorting of ore that use sensors based on colour or other suitable rock properties. The cement industry and some gold roasters have used the alternative of dry grinding and classification, which might also have a part to play in dry processing. There is also likely to be increased interest in options such as in situ leaching that further minimise the surface disturbance. Underground operations will have to balance the energy savings from reducing the amount of material brought to the surface and reduced surface disturbance against the practical limitations of installing and maintaining processing equipment underground. On the other hand, surface disturbance and energy issues in open cut operations will be balanced by potentially lower mining costs and higher overall recovery from the deposit.

Jan 1, 2008

Copper refining electrolytes are maintained in the range 60-65¦C to ensure an efficient operation. The heat energy required to meet these temperatures has been traditionally derived from the electrical energy required for the electrolytic process and supplementary steam energy. In 1983, experiments were conducted at Copper Refineries Pty. Ltd. (CRL) to determine the effects of insulating the Tank House cells, and fully covering the cells. The results of these experiments showed conclusively that greatly reduced steam consumption would be required to maintain electrolyte temperatures. These positive results led to an Energy Conservation Programme for the Tank House, and this was implemented in 1984. A computerised cell cover monitoring system was developed, and is used to control cell coverage and fluid balance. The experimental work and the benefits obtained since implementation of the programme are discussed.

Jan 1, 1985

By Hatherly P, Dunn P

There are- several in-seam coal research projects currently under investigation by the Cooperative Research Centre for Mining Technology and Equipment (CMTE). The overall aim of the projects is to produce new technologies to enhance safety and the efficiency of in-seam gas drainage drilling. Results from high pressure waterjet rotary drilling trials indicate that by applying high pressure water to a rotary drill bit, the hole can be drilled to follow the planned trajectory very closely. Steerable drill bits for drilling long holes (>1 km) have been produced and trialed. A flexible high speed drilling system provides a capacity for rapid in-seam drilling, particularly suited to cross panel drainage. Geophysical tools are being developed to provide a geological steering capability and a better understanding of potential gas outbursts zones.

Jan 1, 1998

Faced with rising costs and lower metal prices, several Ontario base metal sulphide mines have changed their method of mining to vertical crater retreat mining. This is a bulk mining method that utilises large diameter holes and mines successive cuts remotely by blasting and cratering the bottom of the drill holes. The orebody is mined from the bottom up. The method in turn has required a change in materials handling to cope with the greatly increased productivity.   This paper presents an overview of vertical crater retreat mining in the Sudbury area using examples from several producing mines. The paper reviews the history of vertical crater retreat mining, various methods of applying vertical crater retreat layouts, the development of in-the-hole drills capable of drilling the large diameter holes required, methods of explosives loading and blasting to achieve the required cratering effect, methods of ground support including backfill placement, and the ore loading equipment presently being utilised including remote control load-haul-dump units and continuous loaders.   The safety aspect of vertical crater retreat mining has been of concern, and was the focus of a provincial inquiry. The benefits in improved safety are demonstrated through an analysis of various records kept by the mines and provincial agencies.   Future trends can now be envisaged, particularly in relation to deep mining. Some experimental work which could have practical applications, is described.

Jan 1, 1989

The introduction of on-stream analysis in flotation circuits has raised the possibility of automatic control of flotation performance by digital computers. The development of control strategies for an industrial zinc cir- cuit is discussed with reference to identifi- cation of the major disturbances, investigation into the performance of the circuit, the design of the control algorithms, the testing of their performance and their implementation in a production environment.

Jan 1, 1983

By J Szymanski, Y Hu

Excavation engineering involves complex processes for primary and secondary extraction of materials. The shovel excavators bear varying mechanical energy input and stress loading across the working bench during excavation. These varying mechanical energy input and stress loading effects cause significant wear and tear and fatigue failure in equipment components. These effects further result in unplanned downtimes, reduced efficiency and high production costs. In addition, the mechanical and electrical control systems must be operated in efficient profiles to generate maximum outputs and efficiency from these excavators. Efficient technologies are therefore required to solve these problems in order to reduce production costs and increase efficiency. In this paper, the authors develop a rigorous simulator for a hydraulic shovel in a surface mining environment. The finite element model is used to capture the stress profile within the shovel components during excavation, such as, the bucket, stick and boom assemblies. The profiles are classified into normal, critical and extreme ranges, with appropriate corrective measures to avoid extreme loading conditions. The loading capability of shovel excavators can be examined by assessing its structural strength against all possible maximum loads working on the equipment. The dynamic model is used to define efficient profiles of the critical structural components of hydraulic shovels during digging operation. This assessment is used to locate the maximum possible loads and the critical sections of the structures. The method presented in this paper forms the basis for developing comprehensive simulator models for efficient shovel operations in constrained mining environments.

Jan 1, 2003

It is well known that in most areas of Central Europe it is not difficult to find water - usually at shallow depths - and to recover and use this water. What is much more difficult, however, is to find water sources that offer both sufficient in quantity and qual- ity. Far too often, there are sources that offer abundant quantities but of poor quality or vice versa, i.e. high quality water but insufficient volumes. In the former case where water quality is not adequate - which is more often than not due to anthropogenic factors and only very rarely a result of geogenic effects - the application of treatment techniques can help to turn such water into potable water that is suitable for human con sumption.

Jan 1, 1988

By K Luthbom, A Lagerkvist

According to the Swedish Environmental Protection Agency, the number of potentially contaminated sites in Sweden is approximately 40 000. The funding for remediation from the Swedish Government alone amounts to $A 60 - 80 M (300 - 400 MSEK) annually for the period 2003 - 2006. Uncertainties will arise when obtaining samples in field, preparing them in laboratories and analysing them. Different procedures give rise to varying errors. Using data for decision-making that does not truly represent the site could be fatal. Misclassification of soil could lead to unnecessary costs or to risks to human health and the environment. The total uncertainty of an environmental sample can be split into analytical uncertainty and sampling uncertainty. The analytical uncertainty is usually known and reported from routine analysis. The size of the sampling uncertainty is less well known. Hence, the question is how big are the sampling uncertainties for contaminated soil and how big is the analytical error compared to the total sampling error? A scrap yard and two landfills within a workshop area were investigated. An excavator dug trial pits and samples were taken with a trowel from the walls of the trial pits. Samples were put into plastic bags and taken off site for preparation and analysis using XRF. Sample preparation included drying and sieving. The samples were homogenised by kneading the sample bags prior to analysis. The sampling and sample handling were performed in an intuitively way without knowledge of sampling theory. However, Pierre GyÆs sampling theory was used for subsequent evaluation of the data from the site investigation. The theory defines seven sampling errors, which can be applied to sampling of soil. Some errors have a variance that can be calculated or at least estimated, while other errors can give some idea whether the bias is positive or negative. The total sampling error varied over three orders of magnitudes from sample to sample. The single largest contributor to the large variation in error was the contaminant level. When comparing the analytical error and the total sampling error the ratio varies more than three orders of magnitude.

Jan 1, 2005

It is commonly accepted that govern ments have a role in the financing of mineral development. The reasons for government involve- ment are examined in general and in the light of the current situation in Aust- ralia, particularly having regard to the ownership of resources. A brief introduction is given to the new Australian Government bodies, the Petroleum and Minerals Authority and the Australian Industry Development Cor- poration, designed to fill a new role in mineral development, and to the basic changes brought about by the Australian Government's decision to become involved in the future development of the country's mineral resources. It is generally accepted that governments do have a role in financing mineral development. This acceptance does not seem to be confined to Aust- ralia alone but is more a worldwide phenomenon. Mineral development has traditionally been regarded as the pre- serve of private enterprise and there- fore is presumed-to be profitable, and so it is instructive to ask why there is this special role for governments.

Jan 1, 1974

By C F. Prins, C LantuTjoul

Mineralisation in alluvial diamond or vein gold deposits is often hosted in trapping mechanisms. For instance, diamonds are nested in bedrock depressions such as gullies and potholes which were carved out by the sea long before the diamond deposition took place. Similarly, gold mineralisation can precipitate in the necks of a boudinage structure. In such deposits, the spatial distribution of the mineralisation is governed by the mutual arrangement of the trapsites and by the grade variations within each trapsite. Reliable estimates can be obtained only if they rest on a proper knowledge of both degrees of variability. This creates a challenging sampling problem, as during the exploration phase it is important to have a good global mean estimate to enable decision making towards the future. A similar problem occurs for local estimates at a later stage of development. To understand and manage the sampling for global means, specific sampling procedures are required based on an appropriate choice of sample support size and spacing. Estimates from such sampling campaigns should be unbiased, and the less variability they display, the better the sampling parameters. The performance and impact of sampling parameters are tested and compared on different simulated deposits.

Jan 1, 2005

By R S. Suglo, G-K Er

Mineral processing is an essential component of a mine production chain and it accounts for significant proportion of the production cost. Over the past decade, significant research progress has been made in processing plant efficiency using theoretical, experimental and simulation modelling techniques. However, these studies are limited to process plant system as stand-alone units with no interactions with the mining units. In order to maximise the total mining system efficiency and more accurately simulate the system, the processing plant must be modelled as part of an integrated mining system. This becomes increasingly important in continuous surface mining systems, with limited ore processing capacity. In addition, plant efficiency is roughly estimated with known parameters or with simplistic statistical data, without regards to the stochastic processes governing these parameters, such as processing plant feed introduction. In this paper, a comprehensive model of the ore processing plant system is given and the object-oriented design (OOD) of the system is briefly introduced. The joint operation of ore processing plant system and haulage system is analysed. Numerical modelling is used to analyse the ore processing plant system under different conditions. Analysis of the results show that the optimum plant capacity is 0.7 tons/sec (2520 tons/hour). The results also show that the plant system resources cannot be fully utilised because the production rate is always less than the plant capacity. When plant capacity reaches an optimum value 0.7 tons/sec, the production rate is about 0.64 tons/sec. The underlying stochastic processes associated with plant and mine capacities cause this variability. In order to reduce this variability, there is the need to tightly set tolerances for the function variables.

Jan 1, 2003

By H Rose, T J. Sheer, M Dumka

Whenever rock is tipped from above, severe eruptions of airborne dust occur into the airways connected to tipping stations of rock passes (ore and waste) on the lower levels of a gold mine in the North West Province of South Africa. An investigation was undertaken to understand the nature of the physical phenomenon, in order to propose possible solutions. Accordingly, measurements were taken underground, involving the simultaneous logging at two levels of the transient pressures produced in the orepass by tipping from various levels. Two portable data loggers with associated transducers were custom-built for this purpose. Measurements were taken during a tipping program in which rock quantities and levels were controlled. Pressure pulses that are generated by the falling rock drive the airborne-dust eruptions. When tipping from a specified level, recorded pressure pulse waveforms were found to be repeatable on any given level, irrespective of the amount of rock falling, but measurements were conspicuously different on different levels. It was recognised that a pressure pulse is generated as the falling rock passes through the constricted region û a relatively narrow neck û at each tipping station. In passing through the constricted areas the mass of falling rock acts as a æleaky piston in a cylinderÆ and compresses the length of the air column in the orepass below that level. Once the rock has passed through the constriction, the pressure is released and this behaviour causes a regular train of pressure pulses that are separated by the time taken for the rock to move from one level to the next. Based on this physical understanding of the dust eruptions, a computational model has been developed that can reproduce all the main features of the measured phenomena. The model has been verified adequately against the measurements and can now form the basis for simulating a range of possible engineering solutions.

Jan 1, 2005

By Ö Aydan

Rock dynamics is one of the most important topics in the field of rock mechanics and rock engineering. The spectrum of rock dynamics is very wide and it includes the failure of rocks, rock masses and rock engineering structures such as rock bursting, spalling, popping, collapse, toppling, sliding, blasting, non-destructive testing, geophysical explorations, science and engineering of rocks, earthquakes, and impacts. Undoubtedly, the rock dynamics issues in Mars would remain to be the same. Although mankind has no direct access to Mars yet, the Mars exploration rovers (Opportunity, Sprit, Curiosity and Perseverance), Mars Reconnaissance Orbiter and InSight Lander provided very valuable data so that some rock dynamics issues can be recognised. The author reports his considerations on rock dynamics issues in Mars from very careful examination of images and data provided from MERs and MRO and discusses their implications.

Nov 29, 2022

Not so many years ago the reason for an inadequate result from a geophysical survey was insufficient data or poor quality data. In many instances such as gravity, magnetic and radiometric surveys, both these constraints are vanishing or have vanished. High quality sensors, improved data storage, accurate differential GPS and top quality interpretive software now enable the interpreter to understand not just the cause of the anomaly but the host environment in which it resides. Examples of potential field data and also data provided by the more complex electromagnetic systems, from Australia Ghana, West Africa, are used as illustrations.

Jan 1, 1997

The Circum-Pacific is defined to include back arcs and continental areas of volcanism. Volcanoes must be regarded as dormant, if the time since their last eruption is less than about ten times the average interval between eruptions, even if they have not erupted for tens of thousands of years or longer. It is important to establish a complete history, over as long a period as possible, for varying volumes of eruptions. In order to assess risk, the average interval between eruptions should be calculated for each range of erupted vo4ume~, in orders of magnitude from about 10 m up to the maximum volume possible at each volcano. Eruptions are considered to consist of individual explosions, and are grouped into eruptive sequences, with the sequences grouped into overall cycles of activity. Frequency of eruption versus volume erupted is a linear relationship for most andesitic and basaltic volcanoes, but is often bimodal at rhyolitic volcanoes, 3 with a slower eruption rate above about 10 km. Worldwide, during the last 7000 years, there have been three known e~uptions with volumes of ejecta of > 100 km , a9d, since 1638 A.D., 7 with volumes > 10 km , and 48 with volumes > 1 km . Average recurrence intervals are about 71 years for eruptions of > 20 km , 39 years for those of > 10 km , and 7 years for those of > 1 km . Rough esti- mates can be made for larger volumes erupted. Mean intervals in the Circum-Pacific are about twice the length of those for the world as a whole. During the last 400 years, about 61% of the world's eruptions of > 1 km3 have taken place in this region.

Jan 1, 1987