Search Documents

By Graham JW, Cullen GV

edicted increase in, Aluminium production and the possibility of a diminishing supply of petroleum coke for anode electrodes in alumina reduction cells makes it desirable to find alternative electrode materials. Brown coal char, with a lower ash content and with an elemental purity similar to petroleum coke, has been produced by leaching in hydrochloric acid, washing with water and charring at 115000. The cost of processing is estimated to be competitive with petroleum coke. Without further processing the bulk density and real density were undesirably low, but. by briquetting the coal before charring and crushing, the bulk density was improved to 92 per cent of the petroleum coke value and the Particle density was improved to 92 per cent of the density of petroleum coke by water-displacement or 75 per cent by mercury displacement. Pre-baked electrodes were prepared from the char alone, mixtures of petroleum coke and char and from petroleum coke alone, all bonded with coal tar pitch. The electrodes were tested for the usual physical properties and were, evaluated for performance in a laboratory size alumina reduction cell. Electrodes based on brown coal char alone were found to be inferior in physical properties, and performance, but mixtures of the char and petroleum coke, despite poorer density, electrical resistivity and carbon consumption on a theoretical basis, in performance tests gave up to 17 per cent better carbon consumption per weight of aluminium produced and 21 percent better electrical current efficiency than the electrodes based on petroleum coke alone. It is suggested that larger scale tests are warranted.

Jan 1, 1970

By M H. Mian

Much has been published on resuspension of sediments in lakes and estuaries. In general, resuspension has implications on transport and release of contaminants from the sediments. It has been shown that wind-induced waves contribute to erosion of sediments, which are then distributed to various sections of the water body by currents. Empirical equations formulated on the basis of cohesionless sediment behaviour have been applied to the design of a few tailings ponds in different parts of the world, especially in the selection of the necessary depth of water to minimise negative environmental impacts. The paper highlights the shortcomings inherent in these equations using field-measured data from a tailings site in Canada. Laboratory measured tailings properties are used to identify critical shear stresses required to initiate tailings erosion. The influence of cohesion on resuspension of fine-textured tailings is discussed.

Jan 1, 2003

The Australian gold industry has in recent years experienced a tremendous growth period, though not to levels prevailing at the turn of the century. There are, however, a number of dynamic factors at play which collectively indicate that it would be unwise to assume that this growth will be maintained; indeed the future discovery of viable new deposits may be insufficient to prevent an industry decline in Australia.The higher gold prices of the 1980's together with technological advances, made previously worked mining centres areas of excellent prospectivity. These resources, signposted for us by the oldtimers, are being rapidly depleted. Whilst there can be no doubt that these resources can be replaced the real question is whether it is economic to explore for new deposits when it is likely that:The cost of future exploration will increase as exploration must focus on grassroot areas with few signposts. Almost by definition this primary exploration effort will be subject to a lower success ratio.The cost of future exploration will increase as new deposits will be located in more remote areas and at depth.

Jan 1, 1986

By Downs M

The use of a cutting machine designed to allow simultaneous cutting and setting of roof supports has numerous advantages few development roads in coalmines. The use of such a machine with the added ability to cut a curved roof profile is of considerable interest for longwall development in thick coal.

Jan 1, 1998

By P Commander

Western Australia is a major exporter of minerals, which places significant economic and environmental responsibility on Government and the stateÆs mining industry. Moving into the 21st century, mineral production in Western Australia is $14 billion accounting for 50 per cent of the stateÆs export income. There are over 60 large-scale mining operations distributed throughout the arid regions of the state (less than 300 mm/year rainfall). There are four key mineral provinces in arid Western Australia including the Pilbara (iron ore), Murchison (gold), Northern and Southern Goldfields (gold and nickel). These provinces have significant differences, particularly in respect to groundwater demand from mining and mineral processing, aquifer systems that are utilised, and approaches to groundwater management. The arid nature of the stateÆs interior and subsequent lack of surface water resources has required substantial groundwater resource development by the mining industry. A variety of aquifers have been explored and utilised ranging from shallow alluvium and calcrete, discrete fractured zones in bedrock, concealed palaeochannels and inland sedimentary basins. Groundwater usage by the mining industry is about 150 GL/year with most abstraction related to mine dewatering, mineral processing and dust suppression. Groundwater abstraction in Western Australia is regulated by the Water and Rivers Commission. In the Goldfields, the depletion of brackish (>2000 mg/L) and saline groundwater from storage is permissible, as mining is considered the beneficial use for groundwater which may be as much as 200 000 mg/L. In contrast, the low salinity groundwater of the Murchison and Pilbara is allocated on a sustainable basis. The role of monitoring and ongoing aquifer reassessment is crucial in water management, in evaluating the condition and performance of stressed aquifer systems. Mining operations face a variety of water resource issues ranging from insufficient availability for processing to excessive mine dewatering. These issues also change as a mine operation proceeds through its development, commonly starting with a deficiency and moving into surplus as deeper pits require more dewatering. Operating mines have to contend with three main issues: water supply, wastewater disposal and contamination of local water resources. In contrast, post closure issues are related to aquifer recovery or re-establishment of groundwater equilibrium, development of pit lakes in mine voids and isolation of waste products and associated seepage or run-off.

Jan 1, 2003

By E Werner, J J. Donovan, A J. Morris

Coal mining in the Pittsburgh coal seam, in the eastern United States, began in the late-1700s. Since that time numerous mining technologies have been used throughout the basin. Environmental concerns, particularly mine discharge quality, have only been considered since the early-1970s. During the last 20 years, many of the larger underground mines have closed and are now either flooding or already flooded. In order to understand the consequences and potential future effects of this flooding, mine mapping of the basin has been compiled utilising a geographic information system (GIS) with an emphasis on locating barrier pillars between mines. Mine flooding has been monitored at numerous sites utilising pressure transducers and data loggers. These data have been combined with historical data from mining companies and structure contour maps to yield chronological flooding maps of the basin from 1980 to present. Utilising these maps and the indicated flooding rates, future discharge locations have been identified along with estimates of when these discharges are likely to occur. Related work has identified barrier pillar hydraulic conductivities and vertical infiltration rates as a function of overburden thickness. All of this information has been integrated into a groundwater flow model that simulates mine flooding. This model is useful in defining mine to mine interactions as the various mines fill with water, and the testing of various flooding scenarios. The model will be used in evaluating mine discharge rates and evaluating the options for regional mine drainage treatment.

Jan 1, 2003

By Hall T. P, Taylor R. N

Fluid flow in a 1:14 scale water model of the shaft and settler of the Kalgoorlie Nickel flash smelter has been investigated by flow visualisation and numerical modelling. Detailed flow fields through the reaction shaft, settling chamber and uptake are presented for flow rates up to 800 Vm and a number of burner configurations. The predicted flow fields were compared with experimental data obtained from streak photographs and video recordings. The effects of cessation of flow through individual burners and changes in shaft dimensions were also Investigated.

Jan 1, 1992

By Muir DM

In recent years, significant improvements have been made in the design and operation of carbon-in-pulp plants. Some of the major developments in plant operation and technology are reviewed together with an outline of the research being undertaken in Western Australia. The main problems facing operators include the understanding and control of carbon fouling and regeneration, and the recovery of gold from the carbon. It is shown that carbon fouling by a variety of agents, particularly cyanide, calcium carbonate and silica, cause a significant loss of kinetic activity which in turn leads to poor plant performance. The importance of acid washing and adequate thermal reactivation is discussed. Although the Anglo elution procedure is commonly used in South Africa its use in Australia in preference to the conventional Zadra elution procedure is likely to be re- stricted because of its demand for high quality water. Solvent elution by the recently developed Micron procedure using refluxing methanol, ethanol or acetonitrile vapours is an attractive alternative. This elutes gold in 4-6 hours and provides concentrated gold solutions suitable for simplified gold recovery steps.

Jan 1, 1984

By Perry JH, King RL

The Bureau of Mines in cooperation with Kaiser Steel Corporation conducted two methane drainage studies in an advancing section of the Sunnyside No. I Mine where production was being severely hampered by methane emissions. A total of six horizontal aoreholes were completed during the studies to an average length of 291 meters. Total gas production from the boreholes as of December 1981 has exceeded 6,088,800 m3. Methane emissions into the section were reduced by 40 pct as a result of the first drainage system. The second drainage system is currently producing 11,328 m3/day from four Doreholes. Mining of the section and cementing of the horizontal horeholes is expected to begin within 2 Years.

Jan 1, 1982

Exposure to respirable contaminants in mine atmospheres has long posed a serious hazard to miners. The control of these hazards, some of which can have sudden and catastrophic effects and some others, slow and long enduring consequences, has been a major concern for labor, management and government alike. This concern has manifested itself in four primary mechanisms of control -- (1) regulatory control through minimum standard setting by the passage of mine health and safety laws, (2) engineering control through design and operation of mines according to the best recommended practices, (3) medical control through periodic physical examinations, wearing personal protection devices, etc., and (4) legal and social control through workmen's compensation laws for occupation related health rleterinratinn_

Jan 1, 1988

Market forces, particularly iron ore prices, demand that plant operators achieve higher throughput in the worldÆs iron ore beneficiation plants without compromising yields or efficiency. This means that production cost per ton is of paramount importance and that all major pieces of Processing Equipment have come under close scrutiny to improve throughput at their most efficient performance levels and for the longest possible continuous running time. Without doubt the use of modern engineering standards and materials of construction has contributed to matching these throughput, efficiency and availability demands. However, often not enough attention is paid to the so called æinsignificant elementsÆ connecting this metallurgical equipment, such as chutes, pipes or other conveying systems, and particularly to the sufficient protection of their wearing surfaces. The result can be an unplanned and expensive outage caused by the wear related failure of such components. This paper will discuss:the theory of wear and the multiple factors of material and design that contribute to a reduction in wear; and the combinations of modern wear resistant materials available to todayÆs engineer and how, by intelligent selection and correct application, plant availability can be optimised. Examples outlining how these principles have been applied in South Africa showing some improvements leading to increased plant availability.

Jan 1, 2002

By Dorricott M. G

Rock bolt installation is generally carried out in two steps. First the hole is drilled and the drill steel is extracted, then the bolt is inserted into the hole and tightened or grouted. With single pass bolting (SPB), however, these two steps can be carried out at the same time. This kind of bolting system has at least three advantages, (1) the time used for the bolt installation could be reduced, (2) the condition of safety for the operators could be improved, and (3) the degree of automation of the rock bolting practice could be increased. The study presented in this paper is concerned with the development of the SPB system. The current state of the system is discussed, and further improvement of the technique is explored.

Jan 1, 1992

The prime requirement is market, which for NZ inevitably means overseas markets. In order to be internationally competitive, the economies of scale and mechanical handling are essential. Since significant markets have not been sought, the full extent of our industrial mineral potential is not known. In general the technology exists to impart the desired quality, but at a price. Price is the main constraint, which may confine truly competitive operations to coastal situations to avoid high internal freight charges. Some commercial deposits of construction materials are being sterilised by zoning, making the costs to the consumer and country unnecessarily high. Unless management is enlightened and marketing is forceful, it can restrict growth. There is a good case to mount a search for phosphate minerals. The main growth areas are likely to be direct shipping ores like limestone, silica sand, and olivine, but in particular pumice.

Jan 1, 1978

By Bowdler RJ, Lowson RT, Sarbutt JV

There have been few long-term studies of sulphide oxidation under controlled conditions. The object of this study was to investigate the oxidation and leaching characteristics of pyritic mine material under conditions that were commensurate with field conditions but which could be controlled and monitored on a long term basis. The test material - overburden from Woodlawn Mines Pty Ltd - was packed into a 300 cm high column and leached with water at an infiltration rate of 256 mm y-1 for 5 years. Chemical conditions within the column were continuously monitored by sensors embedded in the overburden and leachate from the base of the column was analysed weekly. The study examined the relationships between heavy metal release and gas, moisture, and chemical conditions in the column.

Jan 1, 1988

By Towsey C. A

Significant advances in regional geochemical exploration techniques have been made over the last 5 years in the search for gold deposits. This has occurred largely by the development of the bulk cyanide ex- tractable gold (BLEG) also known as the Bulk Cyanide Leach (BCL) tech- nique. The technique has been developed and designed for Australian conditions and has two main ad- vantages over the pan concentrate technique preferred by many ex- plorationalists, viz:,. 1. It is designed to collect ultra fine gold common to epithermal and other north Queensland types of gold deposits. 2. The large sample (approx.5 kg) allows very low detection levels, ranging between 0.1 and 0.05 ppb Au. The use of the BLEG technique in exploration has led to the discovery of the Wirralie gold deposit and numerous other epithermal gold prospects previously undetected by pan concentrate and minus 80 mesh (pathfinder elements) surveys in the Drummond Basin.

Jan 1, 1989

By Blair J. R

In the Bayer process, bauxite is leached with caustic soda, forming a solution of sodium aluminate, from which hydrated alumina is precipitated. The efficient operation of the continuous form of this process requires that the concentration of caustic soda be controlled. A computer simulation of the concentration of caustic soda has been conducted to provide information, regarding the dynamic behaviour of caustic concentration, which is not available from normal plant data. The basis of the simulation is a state- space model of an alumina refinery, linearized about the normal operating condition. The formulation of the model, with the relevant approximations and assumptions, is outlined. The simulation of the mudwash section of the. plant is described in detail. A continuous model of the mudwash, having time-varying coefficients, was driven using operating data from an alumina refinery. The modelled response showed reasonable agreement with the recorded plant response.

Jan 1, 1977

There was a time, in the memory of some here tonight, when the annual meeting of The Institute was a nostalgic occasion. Often, in the 1920s, there was comment on the decline of Australian mining and on the lack of new mineral discoveries. When some of our Presidents prayed then for a new Bendigo, and instead were given a Mount Isa, they were justifiably disappointed because of the vastly different capital requirements.In 1967 the mining picture is very different. The recent mining developments in Australia are certainly as important as several Bendigos and several Kalgoorlies. The mining industry in Australia has never been more dynamic than today (Table 1). And if we ask why it is so dynamic, the answer lies in the role which overseas capital is playing in the industry. The contribution of overseas capital should concern us not only because we are members of the mining and metallurgical profession, but also because we have a duty to make our profession contribute as much as possible to the well-being of Australians. It is not sufficient to argue that overseas capital is good for the mining industry; we must also examine whether it is good for the economy and the nation. In this context the current criticism of the inflow of overseas capital into Australian mining is useful, for it gives us an opportunity to see what has resulted from the inflow.In discussing this question I do not suggest that we emulate Captain Hancock, that legendary Moonta mine manager who, according to Oswald Pryor's cartoon, used to say to his miners: "When I say a thing is, it is, even if it isn't". The question can only be discussed on a factual basis; and I would submit that many of the important facts relating to overseas capital in our mining industry are often overlooked or ignored. I would further submit, on the basis of these facts, that Australia's present day mining industry has been largely built on overseas capital and that the overall benefits of that capital to Australia have been enormous.

Jan 1, 1967

A comprehensive understanding of the rocks associated with coal seams, and also of the coal itself, is essential in assessing the likely behaviour of the materials before, during and after the mining process. The nature of the rock materials involved in coal mining can give rise to risks from adverse geomechanical properties, create problems in coal quality control and produce difficulties with environmental impacts, all of which may affect the profitability, impact and safety of the operation. Examples of issues associated with rock composition include slaking and degradation leading to roof, floor, pit wall or spoil pile instability, ignition of methane in mine atmospheres by frictional processes, liberation of quartz-rich dusts into ventilation systems, production of coal with unfavourable preparation or marketing characteristics, and escape of suspended solids or potentially toxic leachates from spoil piles and other types of emplacements. Methods for evaluating rock composition include microscopic examination, chemical analysis and X-ray diffraction, with the latter being especially useful for fine-grained rocks or for clay-bearing materials. Other techniques, such as geomechanical testing and down-hole geophysical logging, are also useful, but give less direct information about the actual composition of the materials involved. Indeed, understanding of rock composition, through microscope or quantitative X-ray diffraction studies, provides a basis for checking information from other sources, explaining different aspects of rock behaviour, and an essential link in relating geophysical or geotechnical data to broader-based geological models as part of the risk assessment process.

Jan 1, 2003

During 1979 the writer had the privilege of interviewing about 50 people with varying degrees of involvement in the industrial arena and all of them in one way and another, had a part to play in the huge and intricate saga of Australian employee relations. They fell into the following' categories Industrial Relations Officers/Managers Academics Politicians Union Officials Representatives of Employer Associations Senior Industrialists Commission Members (State and Federal) Sundry (Journalists, Government Officials). This paper seeks to give an account of their views on various aspects of industrial relations. The interviews conducted were all on a personal and confidential basis so it can be expected that sources will not be identified. Suffice it to say that this account represents, albeit in "potted" form, the opinions of some of the most experienced individuals in the country. It will be seen that in most of the vital areas there is a remarkable lack of consensus. It should be noted that this lack of consensus existed within each of the groups mentioned.

Jan 1, 1980

Separation in magnetic fluids is one of the modern techniques that offer a unique approach to material manipulation in a broad spectrum of industries. Its wide-scale application has been restricted so far for a variety of reasons, including limited throughput, inefficient recovery of magnetic fluids and the cost of commercially available magnetic fluids. This situation has changed recently. Very selective separators, with automated density control, capable of treating a variety of materials in a wide spectrum of densities and particle sizes have been built by DebTech and applied in the diamond industry. Technology for the recovery of magnetic fluids has been developed and low-cost magnetic fluids, with high magnetisation and low viscosity are being produced on a production scale. Scale-up of the technology has been addressed and units capable of treating large tonnages of material have been designed. Such a development thus offers the minerals industry a technology that surpasses the existing technologies in selectivity, efficiency and versatility

Jan 1, 2000