Search Documents

Aluminium in Australia, and in fact all round the world, is made virtually exclusively by the Hall-Heroult process, whereby the metal is derived from the electrolysis of alumina dissolved in an electrolyte comprising fluoride salts. It is the distribution and control of these inorganic fluorides during and after the reduction process which go to make up the bulk of environmental problems associated with aluminium reduction smelters. The emission characteristics of fluorides from the process, the occurrence and effects of fluorides in the environment, and the control techniques wnich are applied in industry, all need to be taken into account in assessing the overall environmental aspects of aluminium Production.

Jan 1, 1977

Coal is of tremendous importance for the Czechoslovak econ- omy. The current annual primary energy demand being about 109 million tons of standard fuel (1 ton of standard fuel - 7,000 coal = 29,308 GJ), coal satisfies almost two thirds of our fuel consumption. If compared with the distribution of resources in the world's fuel and energy pattern, the situation in Czechos- lovakia is significantly different, as shown in Fig. I. One of the causes behind the difference is that the Czechoslo- vak oil and natural gas reserves and, hence, their production are insignificant, so that it is necessary to import them. Brown coal will continue to play an important role as a prin- cipal domestic source of primary energy even in the future. While the share of nuclear power is increasing, brown coal represents strategic reserves in the fuel and energy balance.

Jan 1, 1989

By Bogar D. V

Often dewatering of coal tailings is inhibited by the presence of clays, making it difficult to obtain a high concentration, handleable coal tailings. The net result can be a low concentration, chocolate mousse-like tailings which poses significant sedimentation problems in a tailings dam and represents a significant environmental problem. This paper examines the coal tailings from a Hunter Valley colliery where the tailings properties are influenced significantly by the presence of montmorillonite clay. The influence of the calcium ion on the rheology and sedimentation/compression behaviour of coal tailings . containing montmorillonite already dispersed in water was investigated and revealed that very little improvement in the properties is achieved through the coagulation. The preliminary investigations also indicated that the properties of the tailings were dominated by the presence of the montmorillonite clay. Thus investigations were carried out on the clay alone in water. Investigations into the effect of dispersing samples of the clay alone in water and then coagulating with calcium compared with dispersing the clay directly into calcium ion solutions at the same calcium concentration showed huge improvements in the rheology, compressibility, sedimentation rates and sediment solids concentrations for the second dispersion method, which can be called controlled dispersion. The sediment volume fraction solids improved by more than a factor of two by controlling the dispersion of the clay. The reason for the improved properties lies in the suppression of the initial swelling of the clay, which is initially in the sodium form, thus maintaining the parallel orientation of the platelets that is present before wetting. While swelling is being suppressed, ion exchange occurs with the calcium which results in permanent swelling suppression. In the uncontrolled dispersion case where swelling is uninhibited, the clay is allowed to break up and despite the powerful coagulating nature of the calcium ion, the random orientation of the high aspect ratio clay platelets inhibits effective coagulation. Results indicate that the initial electrolyte concentration of the washwater in a coal washery is the critical factor controlling the dewaterability of clay tailings and the handleability of the dewatered product rather than the actual act of coagulating with the calcium ion. The results presented are of clear practical significance and indicate how coal tailings problems where clay dominates the rheology can be improved considerably by knowledge of the surface chemistry.

Jan 1, 1995

Basic premises for evaluating special characteristics of gold-bearing porphyry metal systems stem from their contrasts with properties of the class as a whole. Included features are differences in geologic, thus tectonic, environments, subtle but real differences in the proportions of accessory metals Mo-Ag-Au that are regionally and within some regions, tempo-rally distinct, contrasts in the Ag:Au ratios, petrological-geo-chemical as well as isotopic differences between intrusive suites, the age and nature of host terranes, contrasts in alter-ation style, and zoning variations of mineralogical and physical properties of rocks. These properties are linked in various ways in different regions and suggest that in large gold-bearing systems where gold may be uniformly distributed, environ-ments of emplacement, and compositions or sources of igneous "progenitors" may dominate in importance over processes, and that systems in which gold is zoned are processes-dominant.

Jan 1, 1990

Comparison of the Zadra, Anglo-American and organic solvent procedures for desorption of gold from activated carbon loaded in carbon-in-pulp gold circuits indicates that the Anglo American and the organic solvent procedures are considerably more effective than the commonly used Zadra procedure. Organic solvent elution procedures, particularly those using acetonitrile and acetone, can provide effective gold elution and very high concentrations of gold in eluate solutions. The operational simplicity and effectiveness of the Anglo American procedure would appear to make it the most satisfactory procedure available at the present time but this may change as the solvent elution procedures become better developed. INTRODUCTION The carbon-in-pulp technique has been introduced into the gold processing industry to by-pass the often lengthy CCD and filtration steps required in the conventional Merrill Crowe cyanidation procedure for gold recovery. Adsorption of gold on to carbon is also a valuable technique for recovering trace amounts of gold from low level waste streams from conventional processing procedures.

Jan 1, 1982

Standard petrographic profiles for many Permian seams from New South Wales and Queensland have been drawn up. The standard profiles of seams of the same age and from one or more coalfields were used to compile an idealized or type seam sequence for those coals in which more than half the seam profiles were similar to one another. A marked similarity existed between at least 7 of the 10 type seam sequences formed. The configurations of the vitrite-plus-clarite contents of the plies of 95 per cent of the seams could be formed from different arrangements of 3 basic sequences: (i) a two-ply sequence with a lower vitrite-rich and an upper vitrite-poor ply; (ii) a two-ply sequence with a lower vitrite-poor and an upper vitrite-rich ply; and (iii) a four-ply sequence of 3 plies with vitrite-plus- clarite decreasing upwards, terminating in a vitrite- rich ply. The third basic sequence was very similar to a succession described for some British Carboniferous coals. Eighty per cent of the Australian Permian coal seams studied began with the first (i) basic type of sequence and are interpreted as originating in peat- forming areas which became progressively drier. More than half the seams were formed in an area with a stable depositional surface level which was subject to oscillations of small amplitude.. Many (30%) were formed in an area with a steadily rising depositional surface level.

Jan 1, 1969

SINCE 1900, five underground fires of consequence have beenrecorded in the Broken Hill mines. These occurred at the Junction(1906), Proprietary (1906 and 1916), Block 14 (1906), and Centralmines (1923). All have been extinguished, but at an enormouscost; e.g., in the eleven months following on the 1923 Central mine fire the sum of £187,123 was expended in fire-fighting operations.To this series may be added others, as the South (1925) and British mine (1918) fires, which were extinguished before serious damage had resulted. All, however, have occurred within a period of 28 years, and in a district where spontaneous combustion, a prolific source of fire in the U.S.A., has been practically nonexistent. Therefore, definite fire risks exist in the underground workings of the Broken Hill mines, and, as a consequence, an active fire prevention policy is a necessity...

Jan 1, 1929

By Watson DF

Calculation of the amount of metal in an ore deposit or mining block should be approached by multiplication and integration of appropriate numerical manifolds describing the spatial distribution of the relevant variables, viz. grade, specific gravity and also thickness for bivariate data. Construction of a numerical manifold necessarily involves some form of interpolation but detailed characteristics of this are often not specified in various automatic methods, some of which even provide manifolds with discontinuities. A manifold used in calculations should describe in a geologically plausible way the spatial distribution of the variable of interest. Different approaches to the problem are discussed and compared. Particular computational inconsistencies emerge when "accumulation" is used as a variable in calculations of average grade. If an ore deposit is variable in relation to its sampling and especially if selection of mining blocks according to grade cut-off is a necessary operational decision, the biases introduced by accumulation methods can bring about serious problems of over-evaluation. Modern computational techniques make unnecessary the use of accumulations; because of potential inconsistencies it would seem unwise to use them in any ore reserve computation.

Jan 1, 1987

Intensive exploration for iron ore in the banded iron-formations (BIF) of the Pilbara region of Western Australia began in the early sixties and almost immediately established the Hamersley area as a major iron province. The early genetic models for the BIF-hosted ores were based mainly on macroscopic examinations of ores from the "hardcap" zone, and generally accepted a direct relationship with weathering effects on a Mesozoic to Tertiary land surface. Brandt (1964) was the first to suggest a difference in age between the high-grade hematite ores and the more common hematite-goethite types. He initially accepted a supergene origin for both, but later opted for a hydrothermal origin for the hematite ores. Apart from MacLeod (1966), the published views of the next decade reflect a largely parochial interpretation of individual ore bodies, centred mainly on supergene models but with some support for hydrothermal concepts. Except for Ayres (1971), none of the models were backed by detailed mineragraphic data. In 1976, an AMIRA-sponsored CSIRO group began a Province-wide investigation of the wide variety of ore types and BIF, with emphasis on geochemical and textural studies. The resulting conceptual model for a world-wide unified supergene and supergene-metamorphic hypothesis is generally accepted in the Hamersleys.

Jan 1, 1986

By Ainslie LC, Toens PD, Andreoli MAG

The geological and economic aspects of the known deposits of uranium in southern Africa are described. Processes influencing uranium mineralisation in the relevant geological environments are elaborated upon in order to define fundamental characteristics of mineralisation in the sub-continent and identify potential areas for the location of new deposits. Several areas, namely the Damara orogenic belt and its extension in Zambia and Zaire, the Bushveld zone, and the terrains of uranium fertilisation from the mantle have a high probability of hosting uranium deposits which are yet to be discovered. Uranium resources of the southern African region have been estimated and production forecasted to the year 2000. This geographic region contains one quarter of WOCA's resources in the Reasonably Assured Resources and Estimated Additional Resources - Category I exploitable at less than 130/kg U. On this resource base, it has the potential to maintain its position as the leading exporter of uranium in the world with a production of 13 350 t U308 by the end of the century. Zambia and Zaire are expected to join South Africa and Namibia as uranium producers in the next decade, with their combined share of projected production being in the order of 10%.

Jan 1, 1986

The Olympic Dam mining operation is some 520 kilometres NNW of Adelaide on the Roxby Downs Pastoral lease. The deposit containing copper, uranium, gold and silver was discovered in 1975 by Western Mining Corporation (WMC). A joint venture was formed in mid-1979 between WMC (51 per cent) and British Petroleum (BP, 49 per cent) for the development and exploitation of the deposit. WMC assumed 100 per cent ownership after acquiring BP's share in early-1993. Ore is won from a highly mechanised underground mining operation and processed to refined products. Current annual output from the mining of 3.0 Mt of ore is approximately 83 500 t of refined copper, 1400 t of uranium oxide, 750 kg of gold and 12 000 kg of silver. Conventional long hole, open stoping techniques are used to extract the production ore. Since stope production began in April 1988, full surveys and appraisals of stopes have been carried out to evaluate the integrity of the design and blasting techniques. This evaluation included the determination of the degree of dilution or non break that had occurred. Performance information also made it possible to re-design any adjacent stopes to retrieve remaining ore and conversely, avoid the chances of targeting backfilled material in the future. Performing stope surveys proved not only to be a time-consuming process but one fraught with access and line-of-sight problems. Occasionally it was not possible to obtain any stope survey data, and as was often the case with the mine pass system, rarely. In 1992 the sudden failure of the pillar between the fine ore and mullock passes and the subsequent delays to production, emphasised the need to effectively monitor pass wear. Initial information regarding the development of the Cavity Measurement System (CMS) prototype (Figure 1) indicated that it had the potential to solve these problems by the introduction of a remote scanning device into a cavity. Following a great deal of investigation, Olympic Dam Operations purchased the first CMS in Australia. This paper discusses its application for all underground void surveys and the procedures developed to manage both field and office requirements.

Jan 1, 1995

The Quioma Mine is located along the axis of the Cordillera Oriental, 130 km southeast of Cochabamba, South Central Bolivia. Silver, lead, zinc, antimony, and gold have been intermittently produced from veins in the Quioma area since Colonial times. Mineralization occurs within steeply dipping fissure veins transecting moderately folded Lower Ordovician sediments. Tectonic activity is early to mid-Tertiary and the vein system parallels the fold axis of a major northwest-southeast striking, doubly plunging anticline. Vein sets occur within a 2 km wide band over a strike distance of 13 km along the northeast limb of the anticline. Economic mineralization occupies syntectonic pre-mineral fault zones developed in more competent stratigraphis units of Lower Ordovician clastic sediments. Veins average 55 cm in width, although mineralized structures up to 3 m wide with a known strike length of several hundred meters have been mined. Mineralization consists of siderite, argentifferous galena, sphalerite, and quartz, with minor amounts of chalcopyrite, barite, and bournonite. Pyrite is rare except at the Boston vein where it occurs with stibnite that contains trace amounts of gold. A marked characteristic of veins in the district is evidence of repeated stages of movement during mineralization. Intrusive rocks are rare in the Quioma area. Narrow porphyritic dikes of Andesitic composition averaging 1 m in thickness have been observed. These dikes occasionally show a close spatial relationship to the veins and are often kaolinized and carbonitized. Vein and dike contacts are sharp and alteration does not appear to extend into the wall rock. Mineral zoning is suggested by antimony mineralization observed in peripheral areas of the anticline.

Jan 1, 1987

By Rienks, Wyborn D

The Ravenswood Batholith in the Charters Towers -Ravenswood area of north Queensland, was formed by three main episodes of granitoid emplacement between the Early Ordovician and the Early Permian. Granite to granodiorite plutons of the first phase of intrusions in the Early to Middle Ordovician, probably formed by partial melting of a thin continental crust as a result of the emplacement of mafic material derived from the mantle. Some of this mafic material subsequently intruded the Ordovician granitoids as gabbro to diorite complexes. The early granitoids were deformed and metamorphosed prior to emplacement of second phase granodiorite to tonalite plutons in the Late Silurian to Early Devonian. These later plutons have generally not been deformed or recrystallised. Geochemical and isotopic data suggest the Siluro-Devonian plutonism may have been generated by a partial melting of the tholeiitic material emplaced in the lower crust during the Ordovician. A third intrusive phase consists principally off Late Carboniferous to Early Permian gabbro-granite complexes, high level granite to granodiorite complexes, and rhyolitic plugs and diatremes near the batholith margin. Gold mineralisation in the batholith is associated with two major events: mesothermal vein formation in the Early Devonian and porphyry types in the Late Carboniferous to Early Permian.

Jan 1, 1990

In the current climate, there is a real need to bridge the gap between theory and the real world mining considerations, and develop viable, cost-effective, high performance thickeners. With a greater need to extract profits from both difficult-to-process ores and lower grade orebodies, coupled with the necessity to produce 'greener', less water intensive technologies, suppliers need to take current thickener designs to the next level and into the 21st century. The complexity of 'getting it right' within a thickenerÆs feedwell, the 'nerve centre' of the thickener, is no small task. Delivering dilution water and mixing this water with incoming feed slurry, addition of flocculant, maximising flocculant-slurry interaction to build aggregate size, minimising unabsorbed flocculant percentage, volume average of solids volume fraction, momentum dissipation ratio, dilution recycle ratio, volume average shear, maximum shear rate at exit, aggregate size on exit, uniform discharge profile and more ù all of these need to occur in the right order and in the right proportions within the feedwell. This paper discusses the genesis and evolution of a new feedwell design, the first major innovation in the thickening industry in over 15 years.

Jan 1, 2008

Working thick coal seams in Poland is a very serious problem. Nearly 40 per cent of all coal is extracted from seams more than 3 m. thick. In absolute figures this represents about 70 million tons of coal per year. Working seams with thicknesses up to 3.5 m. does not present, at present, major difficul- ties. Working thicker seams calls for a steady improvement in order to increase the degree of utilization of the deposit and to enlarge the concentration of output. The problem is sometimes more difficult because, in many cases, the seams are worked under protected surface structures which compels the mines to use hydraulic stowing with all its advantages and disadvantages. Rock burst hazard, the control of which is the basic problem hindering the mining, is a further problem. The mining systems used in Poland are adapted to these natural and technical conditions.

Jan 1, 1976

By Peck RC

The ore body at Elura contains fine grained galena and sphalerite in a matrix which is mostly pyrite. A differential flotation circuit concentrates lead and silver in the first section and zinc in the second. The lead section, shown in figure 1, was sampled in detail previously and the metallurgical performance assessed on a size by size basis. That assessment took no account of liberation and given the fine grained nature of the ore body, this could lead to an incomplete picture of the flotation performance. Liberation measurements were made using the QEM*SEM system on four size fractions of samples taken from seven different streams in the lead section. Using the mineral flows obtained from the mass balance around the lead section an excellent liberation balance was obtained which enabled the effect of liberation on the flotation performance to be assessed. The measurements indicated that only 17 per cent of the galena and 28 per cent of the sphalerite in the flotation feed was liberated. On the other hand 31 per cent of the gangue iron sulphides were liberated. The final concentrate was largely composed of locked galena and locked iron sulphides with 85 per cent of the product being locked. There was a small but significant fraction of liberated pyrite.

Jan 1, 1991

By OÆBrien D, Priddle D

In order to avoid costly moisture penalties on coal shipments and to minimise rail freight costs, screen bowl centrifuges were selected and installed in the Mount Thorley Coal Preparation Plant for dewatering fine coal product. The Mount Thorley fine coal circuit consists of desliming the -0.5 mm (ww) fine coal in two stages of classifying cyclones prior to recovery by froth flotation. Provision has been made to bypass the flotation circuit with the classified flotation feed reporting directly to product and the centrifuge dewatering circuit has been designed to handle either flotation feed or flotation product. Major mechanical failures of the gearboxes and the ceramic tiling occurred early in the operation life of the machines which led to design changes being made to achieve satisfactory operation. This paper discusses the operating experience at Mount Thorley with respect to both mechanical and metallurgical performance of the screen bowl centrifuges since their installation in 1985.

Jan 1, 1989

Historical exploration of the Ballarat East goldfield defined two primary quartz vein lode types. Tracking the intersection of these lodes with vertical lines of enrichment (or so-called æindicatorsÆ) was the basic practice for historical mining. This strategy proved highly successful in terms of identifying quartz veins associated with mineralisation. However, it provides little understanding of the timing or processes involved in the formation of these veins, or the associated emplacement of gold. Current underground mapping shows the Ballarat East gold deposit can be subdivided into four stages of vein formation. The earliest veins (V1 and V2) strike north-south and formed during bedding flexural slip and limb thrust fault propagation in parasitic chevron folds. V3 veins are subhorizontal and relate to further fold tightening involving a transition from east-west compression to north-south extension that initiated re-shear of bedded slip surfaces and additional strike-slip faults. Sporadic V4 veins overprint the shallow-dipping sections of V2 and V3 veins and are associated with weak north-south compression. The V4 veins mineralogy is distinguished by a high carbonate content and sphalerite-galena sulfide assemblage. Vein sampling indicates a significant increase in gold mineralisation where overprinting by the later deformation/veining has occurred. As a result of these observations, a new model is emerging that identifies the chronology, structural control and spatial distribution of respective quartz vein types. This is a major advance in terms of exploration targeting, resource modelling and mine planning.

Jan 1, 2008

The major incentives for developing continuous processes for the production of formcoke are to achieve a wider range of coals which can be used, greater operating flexibility enabling the production of various coke qualities, and environmental improvements. The characteristics of a formcoke which must be considered when assessing its performance in the blast furnace are compressive strength, abrasion resistance, volatile matter, reac- tivity, porosity, density, size, shape, ash yield and sulphur content. Lurgi's development work in attempting to pro- duce a formcoke which meets the specified requirements has resulted in most current efforts being concentrated on the Bergbauforschung/Lurgi hot briquetting process. This process blends hot char produced from a non-caking coal with small quantities of caking coal in a special mixer in the plastic range of the caking coal. The material is subsequently briquetted hot, then subjected to a thermal after-treatment to produce a strong abrasion resistant formcoke. A 650 tonne per day plant for British Steel Corporation is now under construction. A study of the equipment requirements and the operating costs indicate that the economics of large scale formcoke plants compare favourably with those of conventional coke-making plants.

Jan 1, 1975

By Mozley R

Contaminated sediments are a multinational problem. A crucial factor in solving an environmental problem is knowledge of, not only the amounts of polluted soil, the contaminants involved and their concentration, but also the historical background of the problem. Processing polluted soil is a tailor made activity based on rational decisions resulting from a detailed treatability study. Lack of information about characteristic properties of a specific sludge/pollution combination is the main obstacle in the route from first ascertaining that a particular harbour subsoil is polluted, to final identification of the full scale treatment plant. In the first instance, information must be generated regarding the distribution of pollutants in relation to the distribution of the original geophysical components. Based on this information rational decisions can be made on separation at a particular cutpoint and what sequential techniques should be involved for a certain fraction. For this purpose a `fingerprint method' is presented especially developed for investigation of polluted soil and sediments. The heart of the fingerprint method is a series of sequential hydrocyclone separations, by which a series of products is generated. The objective of the fingerprint method is to select an optimised treatment procedure in which the pollutants are concentrated in as small a volume of material as possible, leaving the bulk of the material clean. The pollutants can then readily be destroyed or isolated from the environment. The philosophy and advantages of the fingerprint method are demonstrated for a harbour sludge containing heavy metals as main pollutants. Hydrocyclone separation combined with flotation of both the coarse and fine fraction resulted in reusable and dischargeable products. Flotation of the fraction of fines was carried out by means of an experimental flotation cyclone enabling the selective recovery of mineral particles with diameters less than 10 microns. The overall conclusion is that design and engineering of treatment flow schemes for polluted dredged materials is a tailor made activity based on rational decisions resulting from the fingerprint information.

Jan 1, 1993