Search Documents

By Ramsay WRH

The Mount Stavely Volcanic Complex compri- ses one of a number of northerly trending fault bounded greenstone occurrences in Western Vict- oria, of probable Cambrian or older age. The greenstone belt is coincident with several linear positive aeromagnetic anomalies, which outline the surface and subsurface extensions of these greenstones. Mapping at Mount Stavely has identified serpentinite, variolitic basalt, two-pyroxene and pyroxene-hornblende andesite, dacite, rhyodacite and their pyroclastic equiv- alents. Chemically and mineralogically the volcanics constitute a calc-alkaline assemblage. The mineral potential of the region has been enhanced following a discovery by Pennzoil of Australia Limited near Ararat, of sulphide min- eralisation containing approximately 1 million tonnes at 2.7 percent copper. The volcanic environment of the Mount Stavely Volcanic Complex is discussed in terms of similar environments found in Canada.

Jan 1, 1982

The impulsive loading tests under confining pressure were performed to investigate the dynamic fracture properties of rocks in a triaxial stress state. The apparatus in this study consists of the Split Hopkinson pressure bar, a pressure vessel and hydraulic actuator. Magnetite-quartzite and limestone were selected for the test. The stress-strain curves and fracture strength under confining pressure obtaind in the tests were compared with those of the conventional triaxial tests. Finally it is concluded that on the effect of dynamic that on the effect of dynamic compressive strength of rock, dynamic elastic coefficient of rock and confining pressure etc. on the blasting result

Jan 1, 1990

The Mobile Miner MM130 was delivered to Broken Hill in February 1992. During March the machine was extensively trialled on the surface to test manoeuvrability, climbing ability and muck handling prior to being trammed underground in April. The first cutting test on 30 April 1992 provided promising results. The machine has undergone continual development since it arrived in Broken Hill with aims of ensuring reliability and achieving performance goals. The paper gives a detailed account of recent performance comparing this with the predicted Performance.

Jan 1, 1993

By Scott SD

The 1986 PACLARK Expedition established that propagation of a seafloor spreading zone into continental crust has created a complex series of volcanic basins on the floor of the Western Woodlark Basin. In addition to abyssal basalts, felsic volcanic rocks were recovered - especially at the leading edge in the extreme west. A recent deposit of hydrothermal Fe-Mn oxides was discovered on an axial seamount of basaltic andesite, and seawater plume anomalies suggest current hydrothermal venting elsewhere. As a modern analogue for the settings in which ancient volcanogenic massive sulfide orebodies probably formed, the Western Woodlark Basin warrants further investigation.

Jan 1, 1987

Projections of metal requirements for Japan and the United States indicate growing competit- ion for Australia's mineral output and a critical need for continuing discovery of new reserves. These projections may be modified by economic, social and political controls - the most import- ant factor probably being a shortage and the high cost of risk and development capital. Changing ownership patterns toward joint ventures and increased state participation are anticipated. New developments in global tectonics and metallogeny delineate favourable zones for ex- ploration and permit establishment of priority search areas even in regions of poorly known geology. Declining ore grades and special character- istics to meet technological requirements may modify identification and evaluation criteria. A broad approach considering all environments of concentration within the geochemical cycle is re- quired within any metallogenic province. The exploration geologist must be able to integrate geological theory, mining technology and financial analysis to establish well defined exploration objectives, in terms of economic and geologic models, in concept-oriented programmes.

Jan 1, 1973

The reasons for selecting two stage pebble milling in preference to conventional methods of grinding are discussed. Commissioning of the first section was completed in October, 1969. Improvements in both the operating and engineering aspects were then incorporated in the section commiss ioned in March, 1971.

Jan 1, 1975

By Glastonbury J. R

The kinetics of the direct chlorination of, zircon in the presence of carbon was studied at temperatures between 9000C and 12000 C. From the experimental data it is prop- osed that the most likely mechanism for metal oxide (MeO2) chlorination is as follows: At I Surfaceon zMeO2+ZMeCl - MeOC12 (1) At Carbon MeOC12+C+Cl MeC14+CO (2) Surface It.is envisaged that this type of mechan- ism would occur for both the zirconium and, silicon. constituents of the ore. In the above mechanism; the surface re- actions appear to be fast and not rate controll- ing. In a carbon surface deficient bed the diff- usion of oxychloride intermediate through the boundary layer to the carbon surface becomes the rate controlling step. In a zircon surface deficient bed the diffusion of oxychloride away from the zircon surface controls the reaction. This postulated mechanism can be used to ex-, plain the observed experimental effects.

Jan 1, 1973

By J R. Robinson

Prior to mine development, exploration drilling within the Luise Caldera on Niolam Island encountered gold mineralisation to the northwest of the main Minifie and Lienetz orebodies. This mineralisation was referred to as the Kapit orebody, and ten diamond drill holes were subsequently completed over the area to investigate its economic potential. Several significant mineralised intercepts were returned. These were interpreted using the orebody model developed for Lihir at that time which invoked a strong horizontal control to mineralisation. Additional consideration was given to the elevated geothermal temperatures encountered, the proximity of the mineralisation to the ocean, and its perceived depth below sea level, resulting in the Kapit area being given a low priority for follow up investigation. As a result, no further work was completed over Kapit until recently. The Kapit orebody was the target of an intense diamond drilling programme during 2002/2003. Data from this latest round of drilling has significantly improved understanding of the mineralisation and associated geology. The significant orebody now delineated at Kapit substantially differs from past interpretations, and the latest data has upgraded its economic potential. A resource estimate and other critical studies completed in 2003 enabled an updated reserve statement to be issued in February 2004 including the Kapit mineralisation for the first time. Total Probable Reserves at Kapit stand at 25.2 million tonnes (Mt) at 5.28 grams of gold per tonne (g Au/t), for a total of 4.3 million ounces (Moz) of contained gold.

Jan 1, 2004

By Mckenzie CK

Delay scatter, although widely recognised, has rarely been studied with the aim of critically reviewing blast designs. With current trends towards increased deck charging, and the effect on the number of separate delays in blast designs, delay scatter is shown to have a rather profound influence on the control of initiation sequence and the ability to successfully con- duct pre-splitting and smooth blasting. Determination of realistic delay scatter distributions is the first step towards application to blast design. Delay scatter must be evaluated in terms of deviation from the nominal time, not in terms of deviation from the batch mean, since the latter is not usually known without specific testing, requiring accurate timing instrumentation. Computer programs using Monte Carlo simulation can then be developed to investigate the probabilities of out-of-sequence initi- ation or near-simultaneous initiation within any specified interval. The procedures have been applied to both production and development blast designs in Australia and Chile to improve initiation sequence control and to rationalise and simplify blast designs.

Jan 1, 1988

By Kitzinger F

The economic climate of the Canadian mining industry forced an increased interest in rapid, continuous excavation techniques for hard rock formations. The potential applications and advantages of continuous mining over the present drill- blast-muck labour intensive cyclical methods are considerable. Noranda investigated an electrical technique, Plasma Blasting showing considerable promise for mining hard rock. The background of the technology and the theory of blasting rock with electricity is described. The Plasma Blasting process is based on the fast discharge of stored electrical energy into a small amount of electrolyte, suitably located in the rock. The electrical energy converts the electrolyte into high pressure plasma, which expands very quickly, thereby, generating a shock wave. This shock wave produces a stress field inside the rock, resulting in a blast similar to that made by chemical explosives, but without the deleterious fumes. Noranda is currently blasting boulders of 4-5 tonnes and is at present constructing a mobile, autonomous secondary rock breaker for underground and open pit applications. Tests on in situ hard rock formations will lead to the development of a continuous mining machine. Production rates of 500 tonnes per man-shift could be obtained with such a machine.

Jan 1, 1990

By Zamel GI

The utilisation of fossil fuels, including coal (of which Australia is a large producer and exporter) is a significant contributor to the emission of greenhouse gases. Methane gas, formed during the coalification process, is present in coal seams to varying levels depending on the rank and depth of the deposit. This gas usually escapes to the atmosphere during mining operations without prior conversion to C02 or utilisation as fuel. The quantity of methane released can represent from less than one percent to more than five percent of the carbon content of the coal mined. Per unit of carbon, methane has a greenhouse impact many times that of C02. The emission of uncombusted methane to the atmosphere can therefore represent a greenhouse impact of similar porportions to that of the CO2 formed by combusting the mined coal. However, greenhouse emissions from coal can be minimised by collecting the coal seam methane and converting it to water vapour and the less damaging form, CO2. If such conversion is carried out while performing useful work, the methane can further reduce greenhouse emissions by displacing other fossil fuels. Technology has been developed to allow coal seam methane gas to be economically collected in a pure form, uncontaminated with air. This pure methane can be used to supplement natural gas supplies, to generate power or for the production of chemicals or substitute transport fuels. By collecting and utilising coal seam methane, the greenhouse impact from the mining and use of coal can be minimised, with significant reductions possible in the case of gassy deposits.

Jan 1, 1989

Gravity concentration of tin at Renison Limited uses tables and spirals to treat the various coarser fractions produced from sulphide flotation tailing. An acceptable final tailing cannot be made from one pass over the tables and spirals and therefore the tailing from these separators is reground and combined with the sulphide flotation tailing as the feed to the classification section. The gravity section became increasingly overloaded in the years preceding 1976 due to efforts to maximize tin recovery to the gravity concentrate. In April, 1976, two 2DSV Reichert cone concentrators in series were installed to treat the table and spiral tail- ing stream, prior to regrind, to scavenge a small tonnage of hard, coarse low tin grade material for rejection to final tailing. Gravity section loadings were decreased markedly, allowing operator attention to be directed more to table performance than to spillage collection. An increase in mill throughput of approximately 15% was possible following the commissioning of the Reichert cones. The cones are currently operated to make the minimum tonnage of tailing consistent with reasonable- gravity section loadings.

Jan 1, 1978

By Hayward P. G

Complex ores, characterised by intimate intergrowths between minerals, have previously been treated by flotation with limited success. The most common problem has been that the liberation size is often finer than the lower size limit for selection flotation. A technique has been developed in which the problem is overcome by the use of a selective agglomeration procedure in which the values are coalesced with oil to a size suitable for flotation prior to introduction into the flotation machine. A complex lead ore was characterised by QEM*SEM mineralogy as having a mean galena liberation size of 15 ¦m. The best recovery of lead at 50 per cent Pb grade by standard flotation was 53 per cent. After application of the procedure, 86 per cent recovery was obtained after a single cleaner step. The oil functions as a bridging liquid in the presence of conventional collectors which render the mineral oleophillic.

Jan 1, 1991

An investigation was performed to determine the sequence of events which caused the 1987 surface subsidence and related damage to several homes in Walker County, Alabama, USA (see Figure 1). Surface affects compared to mine maps indicated the subsidence to be mine related. However, two coal seams had been worked under this area. The upper seam, the American seam ranged from 250 to 280 feet beneath the surface in the area in question. It was mined-out before 1955 by room-and-pillar method leaving in place narrow-long pillars to support the overburden strata, and abandoned in 1955. The lower seam, the Mary Lee seam, ranged from 650 to 700 feet beneath the surface. The Mary Lee seam had been abandoned in 1966 and subsequently became flooded. The dewatering of the Mary Lee seam workings in 1986 caused the submerged pillars to be exposed to the atmosphere. Due to multiple seam mining and the fact that workings had been inundated then dewatered, a subsurface investigation ensued to determine the sequence and ultimate cause of surface subsidence. Core sample tests with fracture analysis in conjunction with "down-the-hole" TV camera inspections provided necessary information to determine that the subsidence started in the lower seam and progressed through the upper coal seam to the surface. Evidence from the investigation program established that dewatering of the lower seam workings caused the marginally stable support pillars and the roof to collapse. This failure triggered additional subsidence in the upper seam which broadened the area of the influence at the surface.

Jan 1, 1992

Drum winders have now been built to attain depths of 3000 m and more in a single lift in accordance with the South African Code of Practice SABS 0294, which was introduced at the time of the last hoisting conference in 2000. Since then, this code has not only been followed for several winders in South Africa but was also followed in deep mines in Canada. Design of winders and their braking systems are described in the paper. Koepe winders are in use for high payloads of up to 50 t and to hoisting depths of around 2100 m. As known, the stress range of the hoisting ropes is the key parameter for rope fatigue. However, as per the SABS Code of Practice 0294, relying on static design is not the answer to the question of where the limits are for Koepe installation. The paper describes factors that are recognised to have influence in rope life and suggests definition of new design criteria for friction winders in order to get viable solutions for high-capacity hoisting from deep mines similar to drum hoisting.

Jan 1, 2005

By Benson CD

Increasing numbers of Australian gold companies are active in the United States, due to the great untapped gold potential, which is currently undervalued by traditional U.S. companies. The differences in technical, cultural and financial character between the two mining industries provide the Australian companies with a relatively unique blend of strengths (and weaknesses) that can be used to advantage in the U.S.

Jan 1, 1987

By P Benjamin, H Bohannan, C Farr

Geoffrey Blainey's historical account of the mining activity on the west coast of Tasmania, æThe Peaks of LyellÆ documents the changes over 130 years of activity in the region. Commissioned by the Mount Lyell Mining and Railway Company, emphasis is placed upon the development of the Mount Lyell Mine in Queenstown. Chapter 19 æWidening HorizonsÆ details the review the Mount Lyell Company undertook in 1904/05 to ensure the future of the operation, following the pessimistic outlook regarding diminishing reserves and poor grade ore. The analogies documented between the Mount Lyell Company at that time, and Gold Mines of Australia 90 years on are remarkable, with both companies demonstrating a commitment to the Mount Lyell area through active exploration, the proactive search for alternative technology and the recognition of the valuable human resource. As Blainey writes (Blainey, 1993), æwith its expanding chemical works, its huge Tasmanian mines, its railways and smelter, its coke works and its mine crusade, Mount Lyell was probably one of the nation's five great industrial companies in 1906 or 1907. This brief phase of industrial and mining expansion had its seed in the threat of extinction . . .Æ After a number of reprieves, the Mount Lyell mine did stop production in 1994, but that only provided an impetus for a review and rebirth.

Jan 1, 1998

By Klenowski

Rational design of layouts for longwall operations is greatly facilitated by use of an accurate and economical method for predicting stresses and displacements. The displacement discontinuity method (a form of boundary element method) is based on replacing actual excavation geometries by thin slits of the same plan area. This approach allows three-dimensional stress- analysis at a fraction of the cost of alternative methods. The analyses can be readily performed on economical microcomputers, putting the analysis capability within the reach of mine-site personnel. This paper describes investigations associated with the German Creek Central Colliery, the first longwall operation in Queensland's Bowen Basin. The material properties used in the model, in particular the rock mass and goaf properties, have been 'tuned' to fit stress measurements obtained during extraction of the first and second longwall panels at the mine. The study shows that model predictions based on suitably scaled anisotropic rock strata properties are in good agreement with the stress measurements made to date. This model predicts average chain pillar loads significantly higher than predicted by models based on United Kingdom conditions. A working chain pillar design method is proposed using average pillar loads predicted by the numerical model and ultimate strength characteristics given by Bieniawski's formula.

Jan 1, 1988

By Lawrence L. J

The Australian Broken Hill Consols Mine, situated some 600 yd east of the main Broken Hill line of lode, is noted for its rich ores of silver. In contrast to the vast conformable orebodies of the Broken Hill field, the Consols lode occupies a narrow fissure dipping to the south west at angles increasing from 240 through to vertical and transgressing the strike of the metamorphosed country rock at an oblique angle. This feature, together with the abundance of calcite and siderite and the virtual absence of silicate minerals in the gangue, has led to its classification as an orebody of the Thackeringa type (King, 1953). Recorded production during the period 1890 to 1903 is given as 845,000 oz of silver and 20 tons of lead.The unusually rich silver values of the Consols lode were concentrated at the intersection of the fissure with beds of amphibolite, whereas in the adjacent schists and gneisses the lode became markedly impoverished. From the surface to a depth of some 120 ft extensive surface oxidation had occurred, resulting in the breakdown of siderite and its replacement by limonite and associated manganese oxides.Silver halides, dyscrasite, acanthite and partly oxidised tetrahedrite were the main silver minerals in this zone. With increasing depth the lode material gradually reverted to minerals representative of the hypogene zone.The only previous work specifically on the mineralogy of the Consols lode is that by Smith (1922), one time manager of the mine. His zeal as a mineral collector resulted in much valuable information being available on the distribution of the minerals. More recently, Garretty (1943) noted the...

Jan 1, 1962

Seven papers included in Session 8 of the Third International Mine Water Congress under the heading "Achievements in Mine Water Management & Research" have been reviewed. Only one paper, a case study by Masters on biological treatment of inorganically polluted effluent, has any connection with research in the sense of seeking new, generally applicable knowledge which would advance the frontiers of mine water management. The remainder deal with various aspects of the management of mine water ranging from investigation of the geology of a specific aquifer system through operating dewatering systems to the management of specific effluent disposal problems.

Jan 1, 1988