Search Documents

By D. H. Ryan, J. T. Graham, A. Navarra, J. A. Finch, S. Somot

Pyrrhotite (Po) is widely considered to be the most significant mineral in the self-heating of sulphides. It is therefore desirable to determine the amount of Po in mineral samples. This is commonly accomplished through x-ray diffraction (XRD) or quantitative evaluation of materials by scanning electron microscopy (QEM-SEM). This paper introduces another quantitative method based on Mossbauer analysis that requires limited sample preparation and has the additional potential to detect the sulphur/iron ratio within Po. The technique is explored using pentlandite/pyrrhotite mixtures.

Jan 1, 2009

By Robert D. Brown, Robert B. Parsons

"The mining industry may have survived the October 28 federal budget relatively unscathed, but the same certainly cannot be said of the petroleum sector-and many mining men are left wondering if their industry will be the next one to be singled out for special attention, as federal and provincial governments seek additional revenues and pursue nationalistic or provincial policies.Higher taxes, higher prices, a potpourri of ""incentives"", and a -""Canadianization"" policy mark the principal features of the new National Energy Program released by the government along with Finance Minister MacEachen's budget address.This month, Tax Notes examines the federal budget. with appropriate emphasis on the National Energy Program and its possible future implications forthe Canadian resource industries.IntroductionMost of the Canadian mining industry (tar sands miners excepted) heaved a sigh of relief on the evening of October 28, 1980, as Finance Minister MacEachen confounded the prophets in his budget address by not raising personal or corporation taxes and by making only relatively modest changes in the general tax system. Instead, he concentrated on a sweeping new energy policy. Unfortunately for that important sector of Canada's mining industry which is involved in mining the country's vast tar sands reserves, either now or in the future, the National Energy Program that was introduced along with the budget 'has serious implications."

Jan 1, 1981

By Andrew J. Freyman, George S. Barry

"Mineral endowment in northern British Columbia and the Yukon Territory was assessed on the basis of geological opinion which was gathered in a quantitative framework of subjective probabilities. The survey area encompassed 364,000 square miles and was divided into 310 cells having dimensions of one degree of longitude by one-half degree of latitude. The response solicited related to tonnage, grade and number of deposits of a particular mineral in each cell. The questionnaire sought an expression of mineral endowment down to mine-able depth as distinct from economic expectations. Details on the questionnaire and responses are presented in a series of contour maps on individual commooities, which illustrate the collective occurrence picture of the respondents. The approach is largely dependent on the cooperation of an adequate number of geologists familiar with the region being examined. This approach to an assessment of the mineral endowment of a region has a wide range of applicability, from the focusing of exploration effort to aiding government and development bodies in the formulation of regional strategies and the planning, for example, of road, rail and power facilities."

Jan 1, 1970

By M. Courtin, D. Berthelot, M. Haggis, D. McClarty, R. Payne

Over forty years of uranium mining in the Elliot Lake region of Ontario (1956–1996) has resulted in the production of over 300 million pounds of uranium. With the completion of mining activity, Rio Algom Limited and Denison Mines Limited are utilizing progressive environmental technologies and management systems to reduce and manage the environmental risks associated with the 150 million tonnes of potentially acid-generating tailings in nine regional waste management areas. Water covers designed to reduce oxygen entry and, thereby, significantly inhibit acid generation, have been applied at six of the sites with the Quirke site serving as a demonstration site for the Mine Environmental Neutral Drainage program. All five of Rio Algom Limited’s effluent treatment plants are monitored and controlled from a central control station utilizing a Supervisory Control and Data Acquisition (SCADA) system based on “Fix Dmacs” technology. Scheduling, auditing and reporting of plant operating and environmental monitoring programs for the entire watershed are controlled utilizing the Regional Environmental Information Management System (REIMS). Proper application of these technologies and management systems facilitates delivery of cost-effective environmental monitoring, care and maintenance programs at these sites and provides tools to demonstrate compliance with all environmental performance criteria.

Jan 1, 1999

By Philip W. Johnson, Charles D. Haynes

"Abstract - The coalbed methane industry has become a prominent source of domestic natural gas, with its technology having evolved over the past 30 years. Whereas most coalbed methane wells are able to produce without major interruption over their economic lives, wells operating in an underground mining area are subject to being mined-through. If mine-through occurs, the productivity of the well is at least compromised, and may even be terminated. The economic consequences of mine-through may be relatively simple if mineral ownership and extraction rights are common for the coal and coalbed methane. However, if ownership is not common and a superior coalbed methane lease exists, the coalbed methane ownership must be compensated for lost production caused by mine-through. This paper presents a relatively straightforward method to calculate the value of the lost production caused by the mine-through. It uses technology from mining and petroleum engineering, as well as simple economics and financial management techniques.Sommaire - L’industrie de la production de méthane houiller est aujourd’hui une source importante de gaz naturel domestique dont la technologie a considérablement évolué au cours des trente dernières années. Bien que la plupart des puits de méthane houiller peuvent être mis en production durant l’entièreté de leur vie utile sans interruption majeure, les puits implantés en périphérie de mines souterraines sont sujets à être recoupés par ces dernières. Un tel recoupement peut compromettre, ou même mettre fin à la production d'un tel puits. Les conséquences économiques du recoupement par une mine souterraine peuvent être relativement simples quand les droits miniers et les droits d’extraction sont détenus en commun pour le charbon et le méthane houiller. Si toutefois ces droits ne sont pas détenus en commun et qu’il y a eu octroi d’une concession de méthane houiller de qualité supérieure, les détenteurs du méthane houiller doivent être compensés pour la perte de production résultant du recoupement par une mine souterraine. Cet article présente une méthode relativement simple pour calculer la valeur des pertes de production suite au recoupement par une mine souterraine. Cette méthode fait appel aux technologies de l’industrie minière et pétrolière ainsi qu’à des techniques simples d’économie et de gestion financière."

Jan 1, 2006

By G. A. Brown

"Mining executives are becoming increasingly involved with decisions of the ""What would happen if ... "" variety. Potential changes in government policy, such as tax incentives, E.G.M.A. allowances, etc. affect the economic future of present and proposed mining ventures.This paper will discuss various measures of effectiveness normally used in assessing this future, such as discounted cash flow, etc., and will describe means of introducing uncertainty into the computations. As the recognition of risk and attitudes toward accepting it are very important in the life of a mine executive, there will be a brief discussion of utility theory and its application to risk analysis.Risk models are usually of a size to warrant the use of an electronic computer. Therefore, to demonstrate the simple interaction necessary between a financial analyst and such a model, data will be read into a remote computer from a time-sharing terminal in the meeting room. It will be shown that changes may be rapidly made and alternative policies investigated ""on line"" to a computer."

Jan 1, 1970

By J. D. Clucas, D. B. Dreisinger

"The Starved Acid Leach Technology (SALT) has been developed by Search Minerals to extract nickel and cobalt VALUES (from nickel laterite ores (saprolites) and Caron plant residues. The technology consists of sulfuric acid atmospheric leaching of the ores or residues followed by neutralization and recovery of nickel and cobalt. The acid addition is carefully controlled to maximize nickel and cobalt extraction while minimizing overall consumption of acid by various gangue reactions. The final recovery processes can be tailored for maximum economic benefit. The use of resin-in-pulp processing is advocated as the most cost effective method for initial recovery of nickel and cobalt from lower grade materials. INTRODUCTIONCommercial processes for laterite ore treatment vary according to laterite type and local conditions. The two general categories of laterite ore are saprolites and limonites.Saprolites are generally treated by pyrometallurgical processes for reduction of nickel to matte or ferro nickel alloys. The high cost of drying, chemical reduction and electric furnace smelting requires that the saprolite grade for economic processing is of the order of 1.8% nickel or higher. There are of course large amounts of saprolite that fall below this “cut-off” grade that are not currently economic.Limonites can be treated by the Caron Process which involves drying of the ore, a reduction roast of the whole ore to reduce nickel and cobalt (and some iron) to the metallic state followed by ammonium – ammonium carbonate solution to leach nickel and cobalt. Nickel and cobalt recovery are low (70-85% for Ni and 20-50% for Co). The Caron plant tailings therefore contain high levels of unrecovered nickel and cobalt. Relatively few plants have used the Caron Process and new installations are not anticipated due to the high energy cost of drying and reduction roasting. Nevertheless, plants in Brazil (Niquelandia), Australia (Yabulu) and Cuba continue to operate.The high pressure acid leach (HPAL) process was pioneered at Moa Bay in Cuba in the 1960’s in the treatment of limonites. In the 1990’s the HPAL process was touted to revolutionize the nickel industry with low capital and operating costs for new installations. Murrin Murrin, Cawse and Bulong in Australia were started and in each case the technical difficulties of operating at extreme temperature and pressure conditions and the challenges in “ramping up” a complex hydrometallurgical facility conspired to cause these plants to fail economically. At present, Cawse and Bulong are closed and Murrin Murrin continues to operate after undergoing a financial restructuring."

Jan 1, 2012

By Michael Zurowski

This paper traces the history of International Mogul's assessment program on the Lake Ainslie barite-fluorite deposits of Cape Breton Island. The geology of the area is outlined, and the main vein systems described. The geophysical and geochemical exploration techniques employed are explained, the metallurgy of the ore is covered, and the market prices and economics of operation are described.

Jan 1, 1972

By G. R. Elliott

Foreword The office of the Supervisory Mining Engineer, a branch of the l. Federal Government, is financially interested in no oil company and has no stock to sell. This office, however, is deeply interested in the proper and efficient development of Canada's natural resources. The people of Canada are interested in the petroleum development in Turner Valley for two principal reasons: As represented by the Department of the Interior, they are the largest owners of petroleum and natural-gas rights in the field; As a nation, they are vitally interested in the development of petroleum and natural gas as a national asset, and therefore, also, in all productive property, no matter who directly controls the leases. As has been stated by Mr. Charles C. Ross, Supervisory Mining Engineer, "The Department, being responsible for the administration of these public resources, necessarily requires regulations to protect them from abuse by lessees. Our portion of this responsibility is to record a complete history of all drilling operations and to see that proper drilling methods are adopted to prevent damage and wanton waste of the valuable natural resources under discussion." Not only does our position necessitate an impartial and a judicial viewpoint, but, being day by day in touch with all operations in the western provinces, we are uniquely situated to comprehend both individual and general problems.

Jan 1, 1930

By A. D. Huffman

This paper covers the major salt deposits of Canada, with a brief summary of the early history of the industry and a more extended outline of progress since the second world war. Both dry mining and solution mining are covered, and the future of salt mining in Canada is discussed.

Jan 1, 1968

By S. Downing, T. Grammatikopoulos, N. Hoffmann, C. Gunning

"Most deposits display a high degree of geological and mineralogical complexity that can affect metallurgical processing. Therefore, the proper characterization of the ore and gangue minerals requires a multi disciplinary approach combining geology, mineralogy, geochemistry and processing. However, mineralogy to a large extent informs the metallurgical process. Automated methods can be used throughout the mining chain from advanced exploration through to production.In this presentation we discuss actual case studies where automated mineralogy has been applied in a geometallurgical framework at a pre-feasibility to feasibility level. These include examples from a strongly serpentinized magmatic Ni deposit (Dumont) and a magmatic Cu-Ni deposit (Maturi). Mineral speciation and ratios, e.g., chalcopyrite, cubanite, and pentlandite/pyrrhotite are critical to model the Cu-Ni magmatic deposit. In the serpentinized Ni ore, automated mineralogy is used to speciate the Ni minerals into sulphides, alloys and refractory Ni in the silicate matrix.The mineralogical results are linked to the metallurgical test work in order to model the geometallurgical domains. These case studies will illustrate how mineral quantification and improved understanding of inherent mineralogical parameters in relation to metallurgy reduce technical risk in both exploration and flowsheet development.INTRODUCTIONGeometallurgy is a cross-discipline approach combining geology, metallurgy and mine planning (e.g., Dunham et al., 2011). It is aimed to improve the understanding of geological, mineralogical and metallurgical parameters of an ore. Informational gaps among the different disciplines are often apparent. Automated mineralogy is shown in many studies (e.g., Eppinger et al., 2013, Philander and Rozendaal, 2013) to constitute the link between geology and metallurgy. The geometallurgical approach can provide specific data to geology, mining and mineral processing development and plant operations. The scope of the automated mineralogy is to illustrate how mineral quantification can improve the understanding of inherent mineralogical parameters in relation to metallurgy, and reduce the technical risk in both exploration and flowsheet development."

Jan 1, 2016

By Andrew Dobson, Cheryl Allen, Enrique Acuña

"Totten Mine return air raise was designed with two parallel fans equipped with silencers to reduce the noise emitted from the outlets into the environment. As development and production of the mine progressed through the past years, the silencer system needed to be upgraded, and additional maintenance strategies have been necessary to meet the regulatory noise limits enforced by the province of Ontario. The current mine plan will require the fans to reach the upper limit of their capacity by Q1 2019. To achieve this operational target, additional silencing capability has been required and Totten Mine has explored alternatives to further extend the noise silencing capacity available considering the current constraints at the mine site. The alternatives included a new silencer baffle design and a new layout that have allowed doubling the length of the silencer system. Using acoustic measurement data collected on several occasions, this paper presents and discusses the performance of the various silencing systems which have been installed on the return air fans at Totten Mine.INTRODUCTION Vale Canada Limited’s Totten Mine is a base metal, underground mine extracting nickel and copper, situated in the Sudbury Basin of Ontario. The mine initiated operations at the end of 2013, and is equipped with two main return air fans and two main fresh air fans located on surface. Both fresh air and return air fans are set in a parallel arrangement to operate as integrated units and are equipped with variable frequency drives (VFDs) to allow for the remote modification of their operating set point, usually between 600 to 880 rpm, depending on the mine’s requirements. The main return air raise (RAR) fans are also equipped with dissipative baffle silencers to attenuate the noise emitted to the environment. Approximately four years ago, acoustical measurements conducted to verify compliance with the applicable regulatory criteria, and respond to noise concerns from neighboring residents, concluded that the sound emissions of the main return air raise exceeded the noise design parameters. The acoustic tones of the fans were audible offsite, at a residential location, approximately 9 km northeast of the mine site. The elevated sound levels and offsite audibility was due to degradation of the original discharge silencers from moisture and particulate being drawn from underground workings and passing through the silencer baffles. The audibility was also due to an outlet directivity pattern which directed noise towards the residential location."

Jan 1, 2019

By C E. Gordon Brown

Aircraft utilization, weather and cost data are given for three separate projects north of the sixtieth parallel in the Northwest Territories and the Yukon Territory. These operations, carried out by helicopter-equipped geological and prospecting parties, have cost $24 to $30 per square mile, depending principally on the distance from the base. They provide adequate surface exploration of areas with 40 to 50 per cent rock outcrop. A good one-inch-to-one-mile geological map can be made. T HE exploration of the Canadian northland has been given increasing attention by the mining industry during recent years. In many cases, the initial problem is to make an adequate reconnaissance of a large area where existing geological information is meagre. The Geological Survey of Canada pioneered the use of helicopter-equipped geological parties for mapping at a scale of eight miles to the inch.

Jan 1, 1964

By Robert Strachanm

The East Kootenay coal-field, situated close to the boundary between the provinces of Alberta and British Columbia, is composed of four small areas locally called the Crow's Nest Pass, the Upper Elk, the Flathead and Crown Mountain, and comprises an area of about 3 78 square miles. From eleven to twenty-five seams have been exposed of two feet and over in thickness, with a total thickness of about 200 feet of coal, and reckoning about one hundred feet to be workable, gives an estimate of coal available of about thirty-seven billion tons. The coal is a high-grade bituminous, occasionally tending towards anthracite, and the majority of the seams furnish a. very good quality of coking coal as well as an excellent steam coal. The coal-field is found in the mountain ranges in long narrow strips. The age of the fonnation and the thickness of the covering beds have had considerable influence on the character of the coal, and lateral pressure and disturbances in the process of mountain-building have wrought great changes. With such an abundance of coal, it has been a disappointment that the East Kootenay field has not figured larger industrially. So far only one portion of the coal-field has been utilized. This is the Crow's Nest, where, in 1898, the Crow's Nest Pass Coal Company commenced development. Access to the coal seams was easily obtained, the mountain creeks having eroded away the covering, and mines were driven into the coal seams. In that year about ten thousand tons of coal were produced from the mine at Coal Creek.

Jan 1, 1924

By P. Rosario

"Industry practice for high-pressure grinding roll (HPGR) assessment and sizing relies on tests using pilot-scale machines with 0.7–1.0 m roll diameters. Typically 1–10 t of sample are required, depending on the level of study and resource complexity. This is challenging during early-stage development, which hinders incorporating HPGR into designs. With support from the Canadian Mining Industry Research Organization, researchers at the Norman B. Keevil Institute of Mining Engineering at The University of British Columbia developed bench-scale piston–die press tests (PPTs) that correlate to pilot- and full-scale HPGRs. This paper describes a new regression model to estimate the HPGR-specific throughput rate using both PPT results and an HPGR database. A case study is presented to show how the current PPT method is used for engineering studies. ¦ KEYWORDS Empirical modelling, High-pressure grinding roll (HPGR), Piston–die press test (PPT), Sizing and scale upRÉSUMÉ La pratique en vigueur dans l’industrie concernant l’évaluation et le calibrage d’un cylindre de broyage à haute pression (HPGR, de l’anglais high-pressure grinding roll) dépend d’essais menés à l’aide de machines à l’échelle pilote dont les diamètres de bobine sont de 0,7 à 0,10 mètre. On a généralement besoin de 1 à 10 tonnes d’échantillons en fonction du niveau de complexité de l’étude et des ressources. C’est une pratique difficile durant les premières phases de développement, qui empêche l’intégration du HPGR dans les plans. Bénéficiant du soutien de la Canadian Mining Industry Research Organization (CAMIRO, l’organisation de recherche de l’industrie minière canadienne), des chercheurs du Norman B. Keevil Institute of Mining Engineering (l’institut Norman B. Keevil de génie minier) de l’université de la Colombie-Britannique (UBC) ont mis au point des essais en laboratoire sur des presses à matricer à pis¬ton (PPT, de l’anglais piston–die press tests), qui mettent en corrélation les HPGR aux échelles pilote et réelle. Cet article décrit un nouveau modèle de régression qui évalue le taux de production spécifique aux HPGR à l’aide des résultats tirés des PPT et d’une base de données dédiée aux HPGR. Une étude de cas est présentée afin de décrire l’utilisation de la méthode actuelle des PPT dans les études techniques. ¦ MOTS CLÉS calibrage et mise à l’échelle, cylindre de broyage à haute pression (HPGR), essai sur presses à matricer à piston (PPT), modélisation empiriqueINTRODUCTION It is widely accepted that high-pressure grinding rolls (HPGRs) are a viable, energy-efficient solution for modern comminution flowsheet design. Table 1 summarizes select examples of HPGR applications in the mining industry. The main benefits of HPGRs are energy savings, which leads to lower operating costs, and stable operating characteristics that can better cope with variations in ore hardness compared to the conventional autogenous (AG) or semi-autogenous (SAG) mill-based comminution circuits."

Jan 1, 2019

By Y. Okita

The Goro Nickel Process, developed over a ten-year period, uses a number of novel processing steps and treats two ore types, limonite and saprolite, together. Nickel and cobalt are solubilized using a 270°C pressure acid leach in sulphuric acid, which rejects the bulk of the Fe into the leach residue as hematite particles. The leach liquor, after CCD, is aerated to oxidize any ferrous iron to the ferric form and is neutralized with limestone to precipitate iron as hydroxides together with gypsum from the neutralization of the free acid. Further neutralization with lime, together with steps to remove suspended solids, reduces the iron to trace concentrations. Nickel and cobalt are directly recovered from the low-iron leach solution by primary solvent extraction using Cyanex 301® (SXl) in a high-strength hydrochloric acid solution. Nickel is subsequently separated from cobalt in a secondary solvent extraction circuit using tri-isooctylamine. A granular nickel oxide is made by pyrohydrolysis, and this allows the recycling of hydrochloric acid to SXl. The process is currently being commercialized to produce approximately 60,000 t/y of nickel as nickel oxide granules and approximately 5,400 t/y of cobalt as cobalt carbonate. This paper describes the process development to control the Fe concentration in the SX1 feed solution.

Jan 1, 2006

By C. Edwards

"The processes for rare earth (RE) extraction include the decomposition of RE ore concentrate minerals, and the concurrent or subsequent leaching of the rare earth elements (REEs) from the decomposed minerals. Ore beneficiation concentrate can be decomposed by, for example, acid roasting, caustic cracking, and chlorination. The REEs can be selectively extracted. The nature of the REE extraction process depends on the concentrate mineralogy and the targeted products. Based on the experience of the Saskatchewan Research Council (SRC) in RE processing, this paper reviews REE extraction from the major RE minerals, including bastnaesite, monazite, xenotime, ion-adsorption clay, allanite, cerite, and eudialyte. An update on the development of RE extraction processes is also provided.INTRODUCTIONRE processing usually involves two operation stages, physical processing and chemical processing. Physical processing, also known as ore beneficiation, separates the RE minerals from gangue minerals to produce an RE mineral concentrate. Chemical processing, which includes extraction and separation processes, converts the RE mineral concentrate to an RE compound which is either an end product or an intermediate product for the subsequent production of individual REEs or other compounds. The RE extraction process uses one or more reagents to decompose the RE minerals and to leach the REEs into solution. The RE separation process uses solvent extraction, ion-exchange, or chemical precipitation to produce either rare earth oxides (REOs) or individual REEs. The authors have previously reviewed RE ore beneficiation processes (Zhang & Edwards, 2012). This paper focuses on extraction processes for a variety of RE minerals. Table 1 gives the chemical compositions of the RE minerals mentioned in this paper. The varieties of RE extraction methods use many different reagents. These reagents are mainly inorganic acids, alkalis, salts, and chlorine gas. The commonly used acids include sulfuric acid (H2SO4), hydrochloric acid (HCl), and nitric acid (HNO3). Sodium hydroxide (NaOH) and sodium carbonate (Na2CO3) are the most common alkalis. Salts include ammonium sulphate ((NH4)2SO4), ammonium chloride (NH4Cl), and sodium chloride (NaCl). HCl is normally used to extract RE from silicate ore minerals such as allanite and gadolinite. The alkalis and H2SO4 are mainly used to leach REs from phosphate ores minerals like monazite and xenotime. The carbonate ore RE minerals such as bastnaesite can be treated using either acids or alkalis. HNO3 is mainly used to leach eudialyte and apatite. The extraction of REs from ionadsorption clay deposits uses salt solutions. Chlorine gas (Cl2) is exclusively used in the RE chlorination process which can be used to treat any RE minerals."

Jan 1, 2012

By Shawn Healey, Ray Norcross

"Site IdentificationNew Britannia MineA 50/50 WX Gold Inc. - High River Gold Mines Ltd. Joint VentureTVX Gold Inc. is the OperatorLocationThe New Britannia Mine is located in the town of Snow Lake, Manitoba, which is situated between Flin Flon and Thompson, 420 miles north of Winnipeg.Brief Description of OperationNew Britannia Mine processes 2000 tonnes per day at an average grade of 4.5 g/t. Mill recoveries are currently 91 YO, accounting for forecast of 98,000 ounces for 1998.New Britannia Mine's mill complex incorporates conventional crushing, grinding and carbon-in-pulp technology. The design capacity of the New Britannia Mine mill is 1850 tonnes per day. The mill has processed upwards of 2300 tonnes per day, with no required upgrades.Gold recovery averaged 89.8% for 1997 compared to the planned 87% recovery expected from projected metallurgical test work. Year to date recovery mid December 1998 stands at 91.1 %Cash costs for the 1998 year to date were down to U.S. $221.49 per ounce, down 12% from the 3rd quarter of 1997. Milling costs for 1998 YTD were at Cdn. $9.38 per tonne and Cdn. $73.50 per ounce.Geology - (Orebody Description)The Snow Lake gold deposit is located within the Aphebian Flin Flon / Snow Lake Greenstone belt. This belt is composed of an assemblage of poly-deformed volcanosedimentary supercrustal sequences intruded by pre and sin tectonic ultra mafic and mafic intrusions and sin to post tectonic granitoid.The principal gold bearing rock at the New Britannia Mine is made up of quartzcarbonate material in sequence of basic and acidic volcanic rocks contained within a shear zone. The ore itself is gold associated with the sulphide mineral arsenopyrite and contains some pyrite, pyrotite, plus chalcopyrite. Proven and probable reserves at December 31, 1997 were at 4.04 million tonnes at 4.6 g/t and underground exploration continues to confirm the extension of the ore zones to depth."

Jan 1, 1999

By Reno Pressacco

Abstract- Agrium Inc. is a world leader in the production, distribution, and marketing of agricultural products and services in both North America and Argentina. The new phosphate mine and mill complex located southwest of Kapuskasing, Ontario, was constructed to replace an offshore supply of phosphate rock, and produces a high-grade phosphate concentrate. The Cargill Township Carbonatite Complex is one of a series of carbonatite complexes in the region that are hosted by the 1.9 Ga aged Kapuskasing Structural Zone. The carbonatites in the mine area have intruded Archean gneissic granodiorite rocks of the Wawa Subprovince, and metasedimentary rocks of the Quetico Subprovince. The Cargill Carbonatite Complex displays a typical concentric zonation pattern from an outer ring of alkalic pyroxenites, through an inner ring of sövite-carbonatite, to a central core of rauhaugite-carbonatite. The initial carbonatite intrusion and subsequent residual orebody have been modified by faulting such that the northwestern third of the complex has been displaced approximately 2.5 km northeast. The phosphate ores are composed principally of residual apatite sands that were formed by the weathering and dissolution of the soluble minerals of the carbonatite protolith. These ores are subdivided by their iron content into high grade (A ores) and lower grade (B1 and B2) ores. They are separated from the primary unweathered carbonatite by a layer of saprolite, whose thickness varies depending upon the composition of the underlying carbonatite. Cretaceous waste materials consisting of well-sorted silica/kaolinite sand and peat deposits are typically found to stratigraphically overlie the ores. A minor amount of the ore feed comes from cemented phosphate ores. All rock types are covered by Pleistocene glacial tills and clays.

Jan 1, 2001

ONE of the morning sessions at the recent Annual Meeting was devoted to a Symposium on ways and means to expedite geological investigation, and also to promote greater prospecting activity, in Canada. It will be recalled that at the 1940 Annual Meeting, held in Winnipeg, a paper(l) prepared by Dr. G. A. Young, Chief Geologist of the Geological Survey, was presented, and was followed by a Symposium on Geological Investigations in Canada(2). On that occasion, the participants were in the main geologists, and they included the directors or other officials of each of the Provincial departments or bureaus of mines. At the Montreal meeting, the subject was discussed mainly from the point of view of the mining industry. The following pages present, in somewhat summarized form, the several contributions to that discussion.-ED. DR. J. J. O'NEILL(3), who was to have opened the Symposium, was unfortunately prevented through illness from attending the meeting. He had intended outlining the main features of his paper on The Exploitation and Conservation of Mineral Resources in a Balanced Development of Canada, presented at the last annual meeting of the Royal Society of Canada( 4). In his absence, DR.J. A. DRESSER presented a summary of the paper.

Jan 1, 1941