Search Documents

By Manqiu Xu, Glen Robertson, Steve Wilson, Pete Quinn

"The middlings circuit, once called the pyrrhotite rejection circuit, at Inco’s Clarabelle mill was a single flotation stage. It used to process a combined feed consisting of the main flotation scavenger concentrate and the non-magnetic portion of the magnetics flotation circuit tails. The typical circuit metallurgy was 55% nickel recovery at 6.5% Cu+Ni concentrate grade. In the past few years, a research project with the objective of improving the circuit metallurgy was initiated between Inco’s research laboratory and the Mill’s Process Technology group. This project has gone through three steps: a) initial laboratory studies, b) on-site pilot plant investigation, and finally c) full plant implementation.The present paper describes the initial laboratory test work. The development of a two-stage circuit consisting of separate rock and pyrrhotite rejection stages to replace the simultaneous rejection of both rock and pyrrhotite in a single stage is discussed. A two-stage circuit simulation based on batch laboratory flotation data is also presented. Further development work, including the on-site pilot plant test work and the plant implementation of the new circuit design, will be described in a later publication.INTRODUCTIONThe milling operation at Inco’s Clarabelle mill, Copper Cliff, Ontario processes a rich complex sulfide ore from several large production mines around the Sudbury basin (Agar, 199 1). The sulfide mineralization is simple, consisting of chalcopyrite (Cp), pentlandite (Pn) and pyrrhotite (Po). The main gangue minerals are pyroxene, feldspar and quartz with minor amphibole and talc. Estimates of mineral composition are routinely calculated from Cu, Ni and S assays. In the mineralogical calculations, all gangue minerals are conveniently grouped and treated as rock (Rk)."

Jan 1, 2000

By A. M. McKim, J. S. Ambler

"The iron ore of the Scully Mine is upgraded from 36 per cent Fe to 66 per cent Fe through single-stage crushing, wet autogenous milling, sizing by vibrating screens and two-stage spiral separation, followed by a process in which the concentrate is dried and then further improved by high-tension separators. The capacity of the concentrator is 17,000 long tons of concentrate per day. Discussion of the operation will recognize the special problems encountered in handling preponderantly fine ore, relate issues of interest regarding wear and review mechanical innovations found to be advantageous at Wabush. The modern trend toward big equipment, thoroughly instrumented, has been the theme of design. Effects on availability must be a consideration in this choice, and sectionalizing of circuits to minimize these consequences is as important as streamlined maintenance."

Jan 1, 1969

By Atul Bhatnagar, M. P. Sinha, Md Zahid Ahmad, Pallav Garg, Sanjay Kumar Singh, Shashi Ranjan, An Ecolab Company Nalco Water

"Froth Flotation is undoubtedly one of the most critical processes in coking coal washing plants. This work was carried out at Bhelatand Coal Preparation Plant of Tata Steel was with an objective of cost optimization in fine coal processing. The sources of raw coal for the plant include coal from underground mines of Jharia coalfield and procured open-cast raw coal. Coal from different sources vary in quality and possess different floatability characteristics.Synthetic collector is being used in plant as a flotation reagent. An alternate collector with new chemistry was developed for reducing total treatment cost without compromising product yield and quality. A series of laboratory tests were conducted to assess the performance of various sources of raw coal and plant scale trial was started. At first, the new generation coal collector was entirely substituted with the existing collector in the laboratory scale. However the plant scale trial data was not in accordance with laboratory results and indicated inferior flotation performanceThe issue was studied and data based conclusions were drawn that the new generation collector aids faster and uncontrollable kinetics. A decision was taken for co-dosing of the synthetic and new collector for the second phase of the trial. A detailed laboratory analysis was done again and few dosing ratios that predicted optimum results were selected for plant trial. The dosing ratio was optimised as per flotation yield and product ashes during the plant trial. The results showed significant improvement from the first phase and optimum dosing rates were decided based on plant observations and data collection. The influence of various process indicators including water quality, feed and product ashes and process yield was studied during all the trials and promising results were established. The co-dosing of both the collectors conferred cost advantage and enabled to achieve superior performance."

Jan 1, 2016

By A. S. Gendron

A brief description of Inco's ORC copper refinery tankhouse and the electrowinning tankhouse is followed by a comparison of the requirements for the production of the high-quality copper in both systems. The description will focus on both tankhouses, with emphasis on experience to date in the electrowinning tankhouse. Particular attention will be paid to sensitivities of each tankhouse to process upsets which can. significantly afject the quality of the product cathodes.

Jan 1, 1977

By J. A. Herbst

Professor Klaus Schönert and his students used fundamental physics to develop many of the principles required for the design and scale-up of "Gutt Bett Zerkleinern" devices such as the high pressure grinding roll (HPGR) or the high pressure roll crusher (HPRC). As the equipment evolved so have the tools used for its selection and analysis. In the current paper discrete element modeling (DEM), Metso's proprietary Fast Breakage simulations, and Schönert's packed bed piston test are combined with energy based population balance models (PBM) to yield an alternative to ore characterization and equipment selection by pilot plant testing. The resulting methodology is used to take the next step in understanding these devices with a view toward predicting plant performance. This paper describes a journey beginning with precise modeling of a small HPGR including stud geometry and system hydraulics. A key to predicting performance is the accurate modeling of individual particles, their motion in the machine, the probability of breakage and redistribution of fragments, and the inter-particle breakage events that occur between the rolls at different pressures, speeds and moisture levels. Advanced DEM simulations and particle breakage characterization methods provide the necessary technology. The resulting combined models were validated using a small diameter laboratory scale unit. The validated physics based model was used then used to predict the performance of plant scale units using a specific energy based scale-up method. Scale-up results are analyzed in terms of power draw, throughput, and discharge product size distribution.

Jan 1, 2012

By Namavari. H., M. Ashouri, M. R. Sarhadi, S. H. Mansouri, A. Sarrafi

The splash phenomenon and its effective parameters in metallurgical converters have been studied thoroughly for decades. The detailed studies of processes such as tuyere blockage, wave formation during air injection, entrapped phases, and also processes which control the formation of bubbles in viscous fluids are not feasible yet. In this research, we have used a converter-shaped vessel made of flexi-glass. Water and oil have been used as matte and slag phases respectively. The effective operational factors responsible for creation of splashing have been studied such as air flow rate, tuyere angles, depth of tuyere submergence, tuyere blockage, density and viscosity of liquids, liquids heights, etc. The results have been found as follows: the amount of splashing increases slowly as air flow rate increases. However, as the air flow rate reaches a critical value (depending on the physical specification of converter) the amount of splashing rises sharply, because the flow of air inside the liquid changes from bubbling into a jet stream; and most of the splashed materials are in the form of filaments instead of droplets. Changing tuyere angle from horizontal towards vertical position will increase the turbulence level on the fluid surface and causes an increase in the amount of splashing. The effect of tuyere submergence is related to the converter opening angle. As the converter opening angle is shifted towards the hood position, the amount of tuyere submergence and splashing will increase. As density of the liquid increases, the number of droplets splashing increases with a decrease in drop size. Therefore, the total amount of splashing decreases. However, as viscosity of the liquid increases, the splashing material increases due to the changes in the splashed material from droplet shape into filament form. The height of liquid inside the converter, depending on the relative height of heavy phase and light phase, is an important parameter regarding splashing. As the relative height of heavy phase to light phase increases the splashing will decrease. The tuyere blockage will cause the pressure in the inlet manifold to increase; and in real cases will increase the splashing. Finally, we have development a model based on dimensional analysis to relate the above parameters in order to calculate the amount of splashed material.

Jan 1, 2007

By A Hitchen

A general outline is given for the determination of copper, nickel, cobalt, zinc, lead, cadmium, bismuth, manganese, uranium, molybdenum, vanadium, sulphate and fluoride by polarographic or amperometric methods in a variety of ores or metallurgical products. The detection of oxygen in gas mixtures by an amperometric method used as a safety device is also discussed. Introduction I N this paper, a general outline will be given of the polarographic and amperometric methods used for the chemical analysis of various ores and metallurgical products in the Chemical Analysis Section of the Extraction Metallurgy Division of the Mines Branch. The methods to be discussed will be confined to those based on the use of normal D.C. polarography and will not include those methods which utilize a cathode-ray, square wave, pulse or A.C. type of polarograph. For the sake of convenience, ? the polarographic methods will be discussed according to the type of supporting electrolyte employed, as the same electrolyte may serve to determine more than one element in more than one type of ore. Amperometric methods will be discussed according to the element to be determined rather than

Jan 1, 1965

By J. Ambrose, R. W. Zimmerman

"Shales are highly anisotropic in their mechanical behavior. The strength ( ??1) of anisotropic shales depends not only on the magnitude of the other two principal stresses ( ??2, ??3), but also on the bedding plane orientations (?) relative to the principal stresses. In this study, the role of the intermediate stress ( ??2) on the strength of shale is evaluated using new data from triaxial compression and extension tests. To understand the failure behavior of shales, we have carried out triaxial compression tests ( ??1 > ??2 = ??3) on two organic rich mudstones, at different confining stresses and loading angles. We first fit the triaxial compression data with Jaeger’s plane-of-weakness model, and find that the model is able to represent the strength behavior of anisotropic shales reasonably well. We then carried out five triaxial extension tests ( ??1 = ??2 > ??3) for a high strength-anisotropy shale, and two extension tests for a low strength-anisotropy shale. Results from the compression and extension tests for failure along the weak plane shows that the role of ??2 is not significant for weak plane failure. However, for the low strength-anisotropy shale, the failure strength of the intact rock (i.e., at ??= 0o and 90o) for compression and extension tests were significantly different. This indicates that for intact rock failure, the role of ??2 is important and cannot be ignored.INTRODUCTIONFor many years, various researchers have studied the roles of ??2 for failure of isotropic rocks. (Mogi, 1967 and 2007; Colmenares and Zoback, 2002; Al-Ajmi and Zimmerman, 2005 and 2006; Haimson, 2009; Ma and Haimson, 2012). The findings from these studies show that the effect of ??2 on the strength of isotropic rocks is generally significant, and cannot be ignored.Since the role of ??2 in the failure of isotropic rocks was recognized, other researchers attempted to extend some of these isotropic failure criteria to anisotropic rocks, but with limited success (e.g., Tiwari & Rao, 2007; Singh et al., 1998; Zhang and Zhu, 2007; Pei, 2008). Smith and Cheatham (1980), on the other hand, conducted true-triaxial experiments on the Green River Shale and used a J2-I1 type relationship to predict the strength behavior, but without considering the effect of the three-dimensional orientation of the weak plane on strength. Therefore, unlike for the case of isotropic rocks, additional studies need to be done to determine the role of 2 on the failure of anisotropic rocks."

Jan 1, 2015

By Eurípides do Amaral Vargas Jr., J. A. de Mello Franco

"It is frequently necessary to excavate a tunnel for Civil Engineering purposes, or wells for petroleum exploitation, in laminated rock mass like schists or phyllites or in highly foliated gneisses. The determination of the pre-existing in situ stresses is essential, in order to assure the stability of these excavations. In most cases, the pre-existing triaxial stress field is arbitrary in relation to the tunnel or well axis. For these rock masses the concept of Generalised Plane Strain can be correctly utilized.There are closed form solutions for the calculation of stresses in anisotropic rock masses under Generalised Plane Strain conditions (Lehknitskii, 1981 and Hong , 1994). Based on these analytical solutions, established for the cases of Generalised Plane Strain, a synthetic problem will be formulated: the theoretical in situ stress tensor acting on this rock mass will be determined, with the aid of Bayesian Inverse Problem Techniques, as developed by de Mello Franco (2009). Additionally, the reliability of results obtained will be evaluated, in accordance with the research performed by this author. INTRODUCTIONThe Inverse Problem Technique, as developed in the paper, is based on the definitions and concepts obtained from the current literature and used for the solution of Inverse Problems, but the innovation to be presented is the utilisation of Bayesian Techniques and the determination of the reliability of the results obtained. This will be shown in a synthetic example where the determination of the in situ stress tensor, from strain measurements in a drill hole is supposedly performed. It is assumed that this drill has its axis arbitrarily placed in relation to the rock mass. Generalised Plane Strain conditions will hold for use with problem. The equations of Beltrami – Mitchel, in agreement to Lekhnitskii (1981) and Ong (1994), will be used in this synthetic case, for calculating strains, hypothetically measured in the hole before the final excavations. Finally a synthetic example for the determination of the in situ stress in a fully anisotropic rock mass, based on Bayesian Techniques and its reliability, developed in de Mello Franco (2009) is presented."

Jan 1, 2015

Risk management has taken on renewed vigor since the economic crisis of the late 2000s. The resources of governments, individuals, and corporations are being stretched to a point where only the most promising projects move forward. Risk management is a crucial part of the decision making process, yet it remains a broad term that includes disciplines from engineering to finance. A collaborative effort will be necessary to ensure that the most auspicious and appropriate projects are the ones moving forward. Risk management can be quantified to an extent by comparing the likelihood of an instance with the result of consequence of the instance occurring. In this manner it is possible to assign risk factors to instances and ultimately, begin to associate monetary value to the instance. Carbon sequestration is an emerging field that has a number of unique challenges. Risk management and mitigation must be an integral part of the overall picture. This begins with the planning and design phase, continues through implementation and production, site closure, and does not cease until termination of liability. The ability of carbon sequestration projects to successfully assess, mitigate, and recover from leaks will be a decisive characteristic of overall success. The costs of mitigation and failure will need to be analyzed on a test level, but will still need to be reliable enough to extrapolate to a commercial level operation. This paper will build a risk management profile based on case studies and field tests in Tennessee and Virginia. These tests are scheduled to commence in late 2013 and consist of small-scale injection tests in unconventional storage reservoirs with an emphasis on enhanced coalbed methane (ECBM) recovery and enhanced gas recovery. The ultimate goal will be to provide a clear and concise direction to move carbon sequestration from the test phase to commercial scale. While it is necessary from a risk management perspective to analyze all risk points, the scope of this paper will focus on pre-injection risk assessment for carbon dioxide (CO2) leakage potential. Despite the differences between the two tests, CBM compared to shale among other differences, a framework for analysis and mitigation can be developed pertaining to leakage risk. The probability of each type of failure will be assessed and analyzed, and plans to mitigate or reduce these risks will be reviewed.

Aug 1, 2013

By Peter Hood

Data on world-wide geophysical activity in mining exploration programs are collected annually by the Society of Exploration Geophysicists' Geo-physical Activity Committee as part of a continuing service to the industry. The data are obtained by sending out questionnaires to all organizations which are known to be carrying out mining geophysical work; the organizations canvassed include mining companies, contractors, government departments and universities. The questionnaire is divided into three sections; namely, ground methods, airborne methods and research. The data compiled from the questionnaires show that world-wide utilization of mining geophysical methods reached a new high in 1967 with total expenditures of (U .S.) $32,323,240. This was divided as follows: ground methods, $18,106,785; airborne methods, $10,-123,405; and research, $4,093,050. For the ground methods, most money was spent on the induced polarization technique ($5,681,780); electromagne-tic methods were second in reported expenditures ($2,010,900). The total reported geophysical line mileage flown was 1,275,072 line miles, with aeromagnetic surveying being the most popular airborne method. The total amount spent on aeromagnetic surveys was $5,832,564 for 895,420 line miles. This gives an average cost of (U.S.)$6.50 per line mile.

Jan 1, 1968

By E. Rezazadeh Azar

Dump trucks are the main mean for hauling earth material within and outside of the construction and open-pit mining jobsites. The real-time monitoring of the material transportation trips is beneficial for proactive equipment management, volume estimation, and productivity measurement. The traditional manual observation is tedious, non-real-time, and expensive; therefore remote sensing technologies, namely GPS and RFID, have been employed for this reason. Ordinary construction videos are another costeffective alternative to monitor dirt loading and hauling operations in real-time. A vision-based system has been developed to recognize and count hauling trips. This system has three modules including object detection, tracking, and action recognition. This system processes videos taken from access roads in which it recognizes dump trucks and then tracks them throughout the viewfinder. The action recognition module is designed to reject false alarms and also terminate tracking. This way, the system is able to count the number of hauling trips and also record the time between each trip. Several state of the art computer vision algorithms were employed to develop this system. Some of these algorithms were modified using spatiotemporal information to minimize the inherent errors of the vision-based methods. The experimental results showed considerable performance of the system for practical application in the construction and mining sectors.

Aug 1, 2013

By Z. Huda

The effect of various percentages of cold-working and recrystallization on the microstructure and hardness of commercially-pure aluminum plate, has been studied. The 'A critical deformation for the aluminum, has been determined. Experimentation involved cold rolling and recrystallization processes followed by quantitative metallographic practice and the hardness measurements. The raw material chosen was a plate of commercial aluminum which was cold rolled to different percentage of cold-work and then recrystallized by heat treatment at 150°C. The critical deformation percentage of aluminum was computed to be around 30% of cold-worked.

Jan 1, 2007

By E. R. Hughes

Introduction Situated 182 miles east of Vancouver, on the Kettle Valley branch of the Canadian Pacific railway, the Princeton coal field is readily accessible to the Coast markets. The area covers approximately forty square miles and present indications are that the deposits should contain at least 300,000,000 tons of coal. Comparatively little development has yet taken place in this coal field. Since the commencement of recorded output, the collieries operating in this area have produced 1,640,518 tons of coal. The coal field proper includes only the Tertiary deposits adjacent to the town of Princeton and does not include the Coalmont or Nicola deposits. Production has never been on a large scale. The largest annual output from any property was 81, 780 long tons mined at the Granby colliery in 1940. Coal output was first recorded in 1909 and since that time fifteen properties are reported to have either mined coal or to have done prospecting or development work; of these, only two are presently active. However, none of the properties now inactive were closed because their coal resources were exhausted. The accompanying key map shows the extent of the Princeton coal field, and the location of the coal mines and prospects in this field General Geology The Princeton field is underlain by rocks of Oligocene age and is one of the series of more or less isolated Tertiary lake basins in which coal, or lignite, has been found in the interior of British Columbia. Resting on the Nicola group rocks of Triassic age, the Princeton sedimentaries consist of sandstones, conglomerates, shales, bentonite, bentonitic clays, and several seams of coal. Tertiary volcanics occur both above and below the stratified rocks and in places they have been thrust through the overlying measures. In some areas, the coal has been burned to a red ash as the result of vulcanism, while in other parts some of the moisture has been driven from the coal, thus improving the grade. The field can best be described by dividing it into two areas: the Southern area, lying to the south of the town of Princeton, where most of the mining has been done; and the Northern area, to the north of Princeton, where very little development has taken place.

Jan 1, 1947

By W. G. Hubler

It has been within only the last two or three years that enough progress has been made in preferential flotation to warrant metallurgists in recommending the installation of commercial-sized plants for the treatment of copper-zinc-iron ores. Until the new processes had been worked out successfully, the treatment of this type of ore had proved a stumbling block in the path of metallurgical progress. Separation of lead-zinc ore is comparatively simple. A lead-zinc ore low in iron may be separated and concentrated by gravity con-centration, provided it is not necessary to grind too fine. Owing to the specific gravity of chalcopyrite and sphalerite being so nearly the same, however, their separation by gravity concentration is out of the question. Complex lead-zinc-iron ores in which the several minerals are intimately associated, requiring fine grinding to free them, have been successfully treated by flotation for the past fifteen years. Galena is easily floated, and its flotation, unlike that of chal¬copyrite, is not affected by the reagents used to inhibit the flotation of sphalerite and iron sulphides. When an attempt was made to use the methods of lead-zinc se-paration on copper-zinc ores, it was found that the depressant re-agents added to inhibit the flotation of the iron and zinc minerals would, under certain conditions, depress a large part of the copper. It was also recognized that, in the grinding of copper-zinc ore, soluble salts were generated which were detrimental to flotation unless properly controlled. The main part of this paper will be a discussion of solutions in the grinding circuit in relation to the pro¬duction of soluble salts and their effect on flotation.

Jan 1, 1931

By Peter Wells, Gordon Marrs, Dominic Fragomeni, Warren Holmes, Daryl Macnamara

"LocationThe Strathcona mill ofFalconbridge Limited is located in Onaping, Ontario, 50 km northwest of Sudbury.GeneralOre from the Falconbridge mines in the Sudbury Basin (Strathcona, Fraser, Onaping, Craig and Thayer Lindsley mines) is processed through the Strathcona mill with 8500 t of nickel ore and 1500 t of copper ore being treated daily. Current capacity is -3 Mt of ore at 1.8% Ni, 1.9% Cu combined grade. Custom feeds are also processed. The valuable minerals in the ore are pentlandite (FeNi)9S8, chalcopyrite (CuFeS2) with some cubanite (CuFe2S3) and very minor nickel sulphides/ arsenides. Cobalt is present mainly in solid solution in pentlandite. There are small but economically important concentrations of precious metals including platinum, palladium gold, and silver. The common non-sulphide gangue minerals are feldspar, quartz, mica, talc, and chlorite while pyrrhotite (Fe7S8) is the major gangue sulphide. The pyrrhotite contains between 0.6% and 1.2% nickel in solid solution and additional nickel as exsolved pentlandite in micron sized blebs. The nickel and copper ores are batch-crushed in a two stage dry crushing plant and then ground in separate circuits. Concentration by flotation and magnetic separation produces a nickel concentrate assaying approximately 16% nickel plus copper and a copper concentrate assaying 30% copper and 0.4% nickel. The nickel concentrate is trucked as a slurry to the Falconbridge smelter while the copper concentrate is trucked as filter cake to the Kidd Division of Falcon bridge"

Jan 1, 2000

By T. E. Wakefield

"Final Galloway (stage) designs for vertical drill and blast shaft sinking projects evolve from complex thought patterns which integrate operational processes, systems and methods of communication, power supply, drilling, blasting, ventilating, mucking, supporting, surveying, dewatering, sealing, concrete lining and shaft furnishing. Attention to ergonomic design detail at the shaftsman / structure interface is at the heart of safe and successful multi-deck working platforms. For economy the end product must have a low mass to reduce suspension rope end loads to be able to use smaller suspension hoists and have lighter headframe structures, be robust to withstand concussion damage, be easily constructible on site, be maintainable in the shaft barrel, and comply with safety and legislated standards. This paper’s ambition is to describe a systematic design framework and sequenced thought process that delivers a product that is engineered with excellence, illustrated by making use of two designs that evolved during recent Galloway projects, one destined for a large diameter man/material shaft, the other for a ventilation shaft. The stage engineering iterative process starts with mapping permanent and sinking hoisting layouts, followed by laying out horizontal deck plans, mostly constrained by the permanent shaft purpose and configuration, whilst maximizing openings to enable muck to be removed rapidly for the best sinking cycles. Concurrently the designer needs to understand the chosen sinking methodologies in conjunction with crewing to determine the number of decks and fix their spacing. Insufficient access to move and line up formwork, set reinforcing rods and pour concrete in the confined spaces of the stage is an inherent major risk to be mitigated. An iterative and integrative process follows for the primary configuration which delves into increasing design detail, accommodating all other methodology influences, resulting in 3D layouts for further risk assessment, review and fine tuning by seasoned shaftsmen. INTRODUCTION Documented colliery shaft sinking practice from the late 1800’s makes reference to purpose built walling (bricked lining) cribs with floors suspended in sinking shafts, thereby allowing shaft lining to proceed concurrently with the excavation. Improvements were made by Sir William Galloway who introduced two decks supported at the corners by angle irons. The sinking stage, or Galloway, has developed substantially over time to be the in-barrel heart of the sinking operation, with overwhelming complexity for those who have to design one for the first time."

Jan 1, 2019

By M. Tiedtke, T. Crary, P. MacPhail, M. Ounpuu

"The SGS carbon-in-pulp (CIP) / carbon-in-leach (CIL) model was used to evaluate and optimize the carbon circuit at Alamos Gold’s Young-Davidson Mine. Plants samples (pulp and carbon) were tested in a series of small scale batch experiments to determine rates of gold leaching and adsorption on carbon from a combined flotation concentrate/tailing product. The testwork data, along with existing plant data were then used to model the performance of the existing CIL plant and optimize the circuit to improve performance and overall recovery. The primary purpose of the modelling exercise was to determine the most cost effective way to lower solution losses at the plant. The modelling was also used to learn how the various parameters in the CIL circuit affect solution losses and the gold inventory tied up on the carbon. This resulted in recommendations for minor changes in the CIL flowsheet, which were successfully implemented in the plant. The approach, results and plant changes are presented.INTRODUCTION This paper presents the details from testwork conducted on samples from Alamos Gold’s Young- Davidson gold mine which is located near the town of Matachewan, approximately 60 km west of Kirkland Lake in Northern Ontario, within the southwestern part of the Abitibi Greenstone Belt. The objective of the test program (completed by SGS Canada in 2013) was to investigate and model the combined flotation concentrate / tailing carbon-in-leach (CIL) circuit and suggest ways to improve gold recovery. The metallurgical test program included mineralogy, rheology, and carbon modelling testwork. Plant information was provided during the test program and used in the optimization process. Upon completion of the testwork, plant changes were recommended and implemented at site (October 2014). Plant results from 2014 to 2017 confirmed the modelling results."

Jan 1, 2018

By J. Bouchard, A. Desbiens, M. Maldonado, R. del Villar

ABSTRACT: Despite many years of practical applications in mineral processing plants, the potential of column flotation has still not been fully exploited. The challenge in measuring some key variables is certainly an important contributing factor to this situation. Reliable online measurement of varibles, such as the froth depth, bias, gas hold-up, frother concentration, bubble surface area flux, and bubble size distribution, provides opportunities for the application of various advanced control strategies and real-time optimization based on an economic criterion. For several years, Université Laval’sLaboratoire d’observation et d’optimisation des procédés researchers have been working on these opportunities. This paper describes the most recent advances and current research trends.

Jan 1, 2011

By F. Vahdatikhaki

Simulation techniques have offered significant boosts toward a cost-and-time-optimized planning of construction projects by enabling project managers to effectively comprehend the behavior of projects. Using historic data from projects of like nature, simulation considers uncertainties involved in a project through accommodating the stochastic modeling parameters. However, the heavy reliance on the statistical data and not taking into account the context-specific features of the project cause the degradation in the realism and accuracy of the simulation models. Similarly, the extent to which a historic pattern could be retrofitted to new projects will decrease in line with the growing uniqueness of the projects and the novelty of construction methods. Furthermore, the existing real-time simulation frameworks are not capable of distinguishing the transient environmental changes, with minimal long-term impacts on the productivity, from the influential changes that will greatly impact an operation. In addition, existing simulation tools are devoid of location awareness, resulting in the inability to consider safety threats in their representation of the project. To address these issues, this research proposes a framework based on the integration of new tracking technologies used in Automated Machine Guidance (AMG) with simulation-driven 4D modeling methods. The proposed framework automates the adjustment of the simulation model based on the updated data from the site, and thus transforms simulation from a predictive tool used at the planning phase to a proactive monitoring platform usable throughout the planning and construction phases. A prototype is developed to test and demonstrate the effectiveness of the proposed approach.

Aug 1, 2013