Search Documents

By Y. Shu, A. R. Laplante

"A laboratory Knelson Concentrator (LKC), 7.5 cm in diameter, was used to study the performance of a similar unit at plant scale, 76 cm in diameter, This paper reports on sampling and assaying procedures and problems, and discusses the performance of the plant unit.The sampling procedure was based on the extraction of large samples, 5-15 kg, and their complete processing with a LKC, to characterize size-by-size performance. The procedure yielded reliable estimates of overall gold assays, after blatant assaying errors were corrected. The plant centrifugal unit concentrate was sampled in situ, which yielded very erratic grades, with a large overall negative bias. Due to the very heterogeneous nature of the concentrate, which can be linked to flow patterns in the riffles of the unit, it is recommended that for future testwork, the concentrate be recovered separately, blended and then sampled.The plant centrifugal separator, when operated at a feed rate of 25 t/h, yielded total and free gold recoveries of 41 % and 62%, respectively. This is much lower than previously reported data, and suggest that at 25 t/h, the unit is overloaded. However, recovery did not decrease with time over a loading cycle of 2 hours, which suggests that present loading cycles, generally 1 hour, can be significantly increased. INTRODUCTIONThe study of gold gravity circuits is plagued with the statistical problem of determining the behaviour of particles occurring with a very low frequency. This problem becomes particularly acute with increasing particle size. For example, considering the average weight of a gold flake in the 840-1200 µm (20/28 mesh) to be about 5 mg (Banisi et al, 1991), a reasonably high grade feed of 10 git would require, for a relative error (standard deviation) of 10% on grade, 100 particles, that is 0.5 g of gold, or 50 kg of 840-1200 µm material (a Poisson distribution is assumed). Gy's formula, for the same data, yields a weight of 33 kg, with a shape factor of 0.1 and a size distribution factor of 0.5. Both results are comparable; to obtain the suggested weight of material, a stream containing 5% weight in the 840-1200 µm would require 1 tonne samples (of unsized material). The problem rapidly disappears with decreasing particle size. Still with Banisi et al's data, a gold flake in the 300-420 µm range averages 0.5 mg in weight; the same 10% error on grade corresponds to a weight of 5 kg. Gy's formula for the same size distribution and particle shape factors as above predicts a required mass of 1.4 kg. This would correspond to an unsized sample weight of 10 kg with 14% weight in the 300-420 µm, for example."

Jan 1, 1992

By Louis J. Cabri

"Mineralogical evaluation of ores containing platinum-group elements (PGE) is fraught with difficulties because of the low grades (often 1-3 g/t PGE), dispersal of PGE (usually as finegrained platinum-group minerals [PGM]), as well as occurring in solid solution in some base metal sulphides (BMS) such as pentlandite and pyrrhotite. Mineral processors not only need to know how the PGE are distributed, that is, their mineralogical distribution, but the grain sizes of the PGM, and especially the associated minerals.After obtaining a representative ground sample, common approaches include studying a large number of polished or polished thin sections, concentration of the PGM and sulphides by different gravity methods (e.g., heavy liquids, elutriation, micro-panning) and study of the produced concentrates. Unfortunately, these methods often do not produce concentrations that are sufficiently representative of a particular ore. The newly developed patented technology of hydroseparation (Rudashevsky et al., 2002) is especially effective at making concentrations of PGM over a wide range of concentrations (down to <300 ppb Pt+Pd+Au) and size fractions, including <45µm (down to a few micrometres in size), a size range not possible by other techniques. This water-based environmentally friendly laboratory technique provides a large amount of data from samples, which can range from 5 to 1000g, giving confidence to extrapolation of results to bench-scale and larger test work, especially when combined with quantitative image analysis to determine modal percent of major minerals and mineral liberation data, needed to predict the minimum (K80) and optimum (K40) grinds. INTRODUCTIONThe invention of the electron microprobe in the early 1960’s and scanning electron microscopes (SEM) with energy dispersive spectrometers (EDS) in the 1970’s presented mineralogists with powerful tools permitting them to obtain chemical and surface area data on minute amounts of minerals in situ, in a non-destructive manner. An area of process mineralogy that has very much benefited from this new technology was the characterization and understanding of PGM species, resulting in rapid growth of newly characterized species (Figure 1). Recognition of the first PGM may be ascribed to the Spanish explorer Ulloa in 1748, who described native platinum from South America. The second PGM (laurite, RuS2) was only recognised in 1866 by Wöhler in placer samples from Borneo (now Kalimantan) and the third (sperrylite, PtAs2) by Wells in 1889 from the Sudbury Ni-Cu sulphide deposits. The discovery of the important Pt-Pd deposits in the Bushveld Igneous Complex led to the characterization of the important Pt-Pd sulphides (cooperite, PtS2 in 1928 and braggite, (Pt,Pd)S2 in 1932). By the early 1960’s, only about 20 PGM were recognised, and many later proved to be poorly or incompletely characterized. Thus, the introduction of electron probe microanalysis (EPMA) led to a 50% increase of known PGM, as shown in a 1972 review on PGM (Cabri, 1972). At the time of the next review in 1981 (Cabri, 1981) the number of known PGM had grown to 75 and as of 2002, it had increased to 109 (Cabri, 2002). However, it is the author’s experience that less than about 25 PGM may be considered to be “common”, i.e., found in many different deposit types, as shown in Table 1, but usually only some of these occur in any one particular deposit."

Jan 1, 2004

By K. D. Mills, R. G. Robins, C. G. Anderson, L. G. Twidwell

Arsenic is a metalloid which has attracted great environmental scrutiny in recent decades. Moreover, its control and deportment is becoming increasingly important in the metallurgical processing of modern complex ores and concentrates. As such the authors of this publication have a combined professional experience of well over 100 years in the study and hydrometallurgical treatment of arsenic. Hence, this paper will cover arsenic fundamentals along with a review of technology for removal, fixation and stabilization. Finally, an application of industrial Alkaline Sulfide Leaching (ASL) of a copper enargite concentrate will be elucidated.

Jan 1, 2014

By Chris Fleming, John R. Goode, James Brown

"Data will be produced from two uranium feasibility studies that were conducted in 2008, both involving uranium recovery from leached slurry by resin-in-pulp (RIP) with strong base resins. Excellent metallurgical results were produced in RIP pilot plants in both studies, and the loaded resins were eluted with strong sulphuric acid and recycled to RIP in an integrated process. Resin losses by either abrasion or mechanical breakage were immeasurably low.Metallurgical results from these two campaigns will be presented, along with an economic analysis of RIP versus the alternative process of CCD or filtration and solvent extraction.INTRODUCTIONThe recovery of uranium directly from pulp with strong base resins in RIP contactors was practiced commercially in the USA in the 1960s, but the process never established itself as a viable alternative to solid/liquid separation and solvent extraction. This was due mainly to the necessity to do a sand-slime separation partially resulting from the unavailability of coarse resin beads, inadequacies in the design of the RIP contactors and screens to separate resin from pulp, as well as problems with the strength and durability of resins in agitated pulps.There have been significant advances in the last 30 years in each of these areas. All the commercial resin manufacturers are now producing very tough, durable, strong base resins, and are manufacturing them in a large bead size that is better suited to RIP applications. In addition, with the emergence and wide spread implementation of the carbon in pulp process in the gold industry in the 1980s, many innovative techniques for preparing leached slurries and separating carbon from pulp have become firmly established. These techniques have proven to be equally applicable to resin separation from pulps in RIP contactors."

Jan 1, 2010

By J. Reinhardt, R. Uken, S. S. Chinnasamy

Au mineralization in the Kilpwal Gold Mine is confined to laminated quartz-carbonate lodes and associated alteration along the Klipwal Shear Zone (KSZ) in the upper Mozaan Group of the Mesoarchaean Pongola Supergroup. The brittle-ductile shear zone is characterized by inner and proximal hydrothermal alteration domains that are comprised of chlorite, epidote, sericite, pyrite, arsenopyrite and gold. Possible sources of gold are: (i) paleo-placer U-Au rich conglomerates from the lower Mozaan Group; (ii) the underlying mafic volcanics of the Nsuze Group; (iii) greenstone belts in the basement to the Pongola basin. Post-Pongola granites probably provided the heat to mobilize auriferous fluids into the KSZ.

Jan 1, 2011

By Y. M. Jubeli

"Gamma-ray spectrometry, an effective tool in geological mapping, was used to de?ne boundaries between various lithological formations in three adjacent areas of Central Syria, namely, the Syrian Desert, Ar Rassafeh Badiayat and the Northern Palmyrides mountains.This paper describes the role of an airborne gamma spectrometric survey which was originally undertaken to assist uranium exploration. Interpretation of the total count data obtained through the survey has led to signi?cant modi?cations and corrections to the previously published distribution map of the palaeogene phosphate rocks.Another important result of the survey is the discovery of four previously unknown phosphorite horizons in the Rasm Al-Aawabed area of the Northern Palmyrides. In addition, previously unknown phosphatic horizons are outlined in the other study areas. The importance of this technique as an effective prospecting method, not only for U but also for exploring for the economically important phosphorite formations in Syria, is emphasized. Furthermore, its role in geological mapping is stressed, especially in areas that lack suf?cient geological data."

Jan 1, 1997

By Philip J. Guerney, S. O’ Leary, André R. Laplante

"Concentration of dense mineral phases (s.g. greater than 7) for characterisation of individual particles and mineral grains by electron microscopy is a well established technique for the detection and characterisation of valuable mineral phases. This presentation describes the type of data that can be generated when both the concentration and characterisation steps are carried to higher levels than typical. The concentration step is the gravity recoverable gold (GRG) protocol that has been used for over 100 ore samples. This protocol yields three concentrates that represent three progressive degrees of grinding and liberation. Three ore samples were subjected to the GRG protocol and three size classes of each concentrate were characterised using the mineral liberation analyser (MLA), an automated, EDX-based tool. This presentation briefly presents GRG and MLA technology, and then focuses on the results obtained: photos, images and databank, the latter used to evaluate the extent of particle liberation and particle shape.INTRODUCTIONThe practice of gravity concentration prior to characterization of mineral samples using electron beam microscopy is solidly established. Typically, a dense liquid such as tetrabromoethane (density: 2.97 g/cm3) is used to reject the light phase, typically carbonates and silicates. The heavy phase, mostly sulphides, oxides and precious metals, is then mounted in a polymer matrix and examined using beam microscopy.Both the pre-concentration and the sample preparation/examination steps have seen significant advances over the past ten years, but are not without problems. A major issue of preconcentration is that most dense liquids used are toxic, tetrabromoethane being a prime example. More recently, a dense liquid with little or no toxicity (sodium polytungstate, distributed by Sometu Inc.) has become commercially available, but its use is limited to relatively low s.g. splits around 3 g/cm3. Dense liquids are viscous, and their use is limited to particles coarser than 37 µm, although centrifuge separation can probably lower this limit to around 10 µm. Magnetogravimetric separators can achieve much higher specific density cuts, but upgrading below 100 µm or in the presence of magnetic minerals remains a problem. The use of centrifuge separators such as the 3-in Knelson Concentrator (KC MD3) or the Falcon 4-in SB (SB4) is particularly attractive since these units can easily process large masses (by laboratory standards) and achieve a cut density well above those of dense liquids."

Jan 1, 2003

By Gilles Landry, Mohamed Ourriban, Pierre Pelletier, Ahmed Bouajila, Claude Gagnon

"This paper summarizes the work carried out to develop and implement the gold cyanidation by size class (CSC) process, a novel concept aiming to reduce cyanide consumption.First, the authors will present the methodology and results of laboratory tests conducted to evaluate the response and the expected gains for the selected ore when submitted to the CSC processing. In the second part, focus will be on the methodology behind the CSC scheme development prior to its implementation at Sleeping Giant Mine concentrator. Finally, the evaluation of the modified circuit performance (operating since July 2007) will be addressed as a reduction of cyanide consumption by more than 30% and of free NaCN in the tailings by more than 50% is confirmed.INTRODUCTIONCyanidation is the most widely used technique to extract gold from hard rock ore. Its use of oxygen as an oxidant still makes it the cheapest process available after more than a hundred years. Unfortunately, gold cyanidation is known to be a slow process that requires high consumption of cyanide. In fact, cyanidation plants are designed with very long residence times (Habashi, F., 1967). Drawbacks of long cyanidation times are, among others, loss of gold in tailings, high reagent consumption and high capital investment and maintenance costs.Responding to their members expectations for the improvement of cyanidation process, COREM undertook a challenging R&D program covering the development of alternative concepts (processes) and the understanding and solving of mass transfer, gold passivation and process water chemistry problems. One of the interesting findings of the R&D program is a patent pending process technology based on the cyanidation by size class (CSC) concept (Côté and Ourriban, 2004; Gagnon and Ourriban, 2007; Gagnon and Ourriban, 2004).The new technology was tested at the Sleeping Giant concentrator, a plant member of COREM. The existing flowsheet was modified in order to implement the CSC process in the full-scale plant. The plant has been operated using the modified CSC based process since August 2007. Laboratory testwork was conducted prior to the industrial application in order to properly design the new process scheme. The modifications included:1) Reclassification of the grinding circuit product through an hydrocyclone2) Leaching of the coarse size fraction3) Addition of the fine fraction to the coarse leaching circuit tails."

Jan 1, 2009

By Dave Bulled

"This paper describes the design of a molybdenite flotation circuit using FLEET technology applied to kinetics data produced from laboratory flotation testing and distributed across the blocks of a mine plan using a geostatistical approach. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the kinetics estimates of each block of ore in the mine plan. The final design then included a quantification of risk based on the accuracy of the block flotation kinetics and model fitting. The design made reference to the extensive technical reports describing earlier metallurgical test work including some pilot plant work over thirty years ago.The testing involved conducting MinnovEX Flotation Tests (MFT) to determine the rougher flotation kinetics at the specified reagent conditions and rougher-cleaner tests to determine the change in kinetics resulting from regrind. These flotation kinetics were used within FLEET simulations to create a full-scale flowsheet and plant design including recommended equipment sizes and the forecast of operating results. Measurement of detailed flotation kinetics for a wide range of samples allowed the effect of size of grind and efficiency of classification (i.e. width of size distribution) to be predicted for the whole ore body.INTRODUCTIONAdanac Moly Corp. proposed to develop a 20,000 ton per day mill to produce high quality molybdenite concentrate from its Ruby Creek resource in north-western British Columbia. It is a relatively clean low grade porphyry-monzonite occurrence containing minimal quantities of other sulphides such as chalcopyrite, pyrite, sphalerite and galena. Molybdenite occurs mainly as coarse flakes with lesser amounts of finer sized values. An optimum plant design was required to can achieve the predicted operating results, at a known level of risk, while treating the variability inherent in the ore body."

Jan 1, 2007

By Hongfei Li, JianLong Wang

This paper introduces the technical characteristics, transformation scheme and production practice of the project in which Copper P-S Converter was replaced by Bottom Blowing Continuous converting for the first time, and introduces the technical achievements obtained by the project. The application practice proves that bottom blowing copper continuous converting technology can completely solve the problems of fugitive off-gas pollution in the ladle transportation, large amount of flue gas and fluctuation of flue gas caused by P-S converting. Comprehensive energy consumption and operating costs of producing blister copper, safety and environmental risks are greatly reduced, and economic, environmental and social benefits are significant. It is one of the preferred technologies for upgrade and to replace P-S converting technology. INTRODUCTION At present, more than 80% of copper production capacity is still using the P-S converting technology with a history of more than 100 years. During P-S converting process, melted copper matte needs to be transported by ladle, and it needs to rotate the furnace body several times, causing a lot of serious environmental and safety risks such as SO2 flue gas emission and low-altitude SO2 pollution. In addition, the high operating cost caused by low rate of air blowing, the short life of the refractory materials and high energy consumption during P-S converting become big problems. Other problems such as large amount of flue gas, low SO2 concentration, large fluctuation of flue gas volume and SO2 concentration, and discontinuous flue gas cause high cost of subsequent flue gas treatment are also needing to be solved. In order to solve these problems during the P-S converting, metallurgical engineer in various countries has spared a lot of efforts to develop continuous blowing process for decades. The continuous converting that have been industrially applied are flash continuous converting, Mitsubishi continuous converting, Noranda continuous converting, Bottom Blowing Continuous converting and multi-lance top blowing continuous converting

Jan 1, 2019

By Andre L. De Vegt, Cees J. N. Buisman

"For the past eight years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Metal and sulfate can be removed from mine waters using two biological steps:1. Sulfate reducing bacteria convert sulfate to hydrogen sulfide (H2S). The H2S reacts with the dissolved metals to form insoluble metal sulfide precipitates.2. Sulfide oxidizing bacteria convert excess H2S to elemental sulfur.Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove metals and sulfate as described above. The system has been operating since May 1992 treating a flow of 5000 m3/d. A test program, utilizing a large scale pilot plant, will commence in November 1995 at a copper mine in the U.S.A. to remediate groundwater contaminated with sulfate and heavy metals. Biological reactor performance and selective metal recovery will be studied. Sulfur dioxide (S02) can be removed from fluegas using a combination of scrubber technology and the two biological steps. The end product is elemental sulfur. A commercial size biological desulfurization plant has been in operation since July 1994 treating 50,000 Nm3/h of fluegas. Sulfide can be removed from mining waters or anaerobic wetlands using a THIOPAQ® Sulfide Oxidizing reactor.lntroductionSulfur can be present in various water and gaseous streams in a mining operation. In many cases the sulfur compounds have to be removed because of toxicity, corrosive properties and contribution to acid rain. Mine waters can contain dissolved heavy metals. An efficient way to remove dissolved metals removal is the precipitation as metal sulfides. Paques has developed and installed treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. These treatment systems biologically convert sulfate to hydrogen sulfide (H2S) which can be used in heavy metal precipitation. Excess H2S is biologically converted to elemental sulfur. This paper provides an overview of these newly developed biotechnological treatment systems."

Jan 1, 1997

Stress induced, gravity-assisted failure processes typically dominate long before stress levels approach the strength of the intact rock (at approximately smax > 0.4UCS where smax = 3s1 ? s3 and UCS is the Unconfined Compressive Strength of the intact rock (Martin et al. 1999)). Under these conditions, discontinuities typically become clamped and the failure process becomes brittle. This brittle failure process is dominated by new stress induced fractures growing subparallel to the excavation boundary. While it is possible to identify areas with the potential for brittle failure, for example, using the general assumption that brittle failure will occur in areas at right angles to the major principal stress (Hoek et al., 1995), when the threshold smax > 0.4UCS is reached in areas around the tunnel boundary, or elastic modelling and the Hoek-Brown brittle parameters proposed by Martin et al., (1999) (i.e. m? 0 and s ? 0.11), amongst others, recent observations discussed by Everitt & Lajtai (2004), and Kaiser (2005; 2006) suggest that brittle failure processes are enhanced when structural features such as joints, weakness zones, bedding planes or foliations are preferentially orientated around the excavation boundary creating stress raisers which in turn facilitate the stress-driven rock mass disintegration process (e.g., as illustrated by Everitt & Lajtai (2004) on Figure 1b). Such weaknesses induce stress heterogeneities that thus promote tensile-spalling failure processes (Diederichs 2000). The observations suggest that stress induced damage can occur ?prematurely? depending on the orientation of micro and macro structures in situations where the known stress conditions should not yet initiate brittle failure processes. In general, when structural features (micro and/or macro), especially foliations, are present in a rock mass, the strength is effectively reduced, largely due to tensile strength heterogeneity in areas depending on the orientation of the structural features with respect to the excavation boundary. As a result, stress induced damage could occur in areas not normally considered due to the influence of anisotropy (Figure 1).

May 1, 2009

By Jonas Olsson

"The picture of China as an antiquated continent is changing rapidly and fast-forwarding progress is a fact in most infrastructural fields. Mining is not an exception. China is today the largest producer of aluminum, coal, steel, zinc, tin, lead and manganese and the country’s mineral resources comprising approximately 12% of the global reserves ranks them number three in the world after US and Russia.In order to feed the growth industry is needed to take extra ordinary strides to improve supply of raw material and Chinese mines are continuously being upgraded with the latest western technology to meet the increasing domestic demand of base metals.In Anshan located in China’s northeast province Liaoning we find one of the fastest developing mining companies, Angang Iron & Steel Group Co. Ltd. With their six mines that together process approximately 60 M ton iron ore/year Angang Iron & Steel Group Co. Ltd is the largest iron ore company in China. The group’s thorough pre-studies and technical evaluations over the past five years have made them very successful in both plant upgrades of existing operations and green field projects.INTRODUCTIONWe live in a time when the world market is gradually acclimatising to the global consequences of “The China effect”. An effect caused by a formerly sleeping giant nation that during the last years has awakened and developed beyond comparison, primarily because of booming infrastructure projects and demand for capital and consumer goods"

Jan 1, 2006

By T. H. Patching, D. F. Coates

The Sub-Committee on Rock Classification, Canadian Advisory Committee on Rock Mechanics, has evolved a classification of rocks which should prove useful in studies of rock mechanics. Considered in two stages -actual rock substance and rock mass -the five-point classification involves the geological name of the rock, the rock strength and rock deformation, and, in the second stage, the gross homogeneity of the rock mass and the formation continuity.

Jan 1, 1968

By A. K. Watt

"The availability of fresh water to meet present and future needs in Ontario is of concern to an increasing number of people. Rain and snow are the source of our potable water and provide, on the average, some 180,-000 billion gallons of water annually. This amount is reduced to 94 billion gallons a day as a result of the evaporation and transpiration of water and our inability to construct the necessary reservoirs for capturing surplus stream flow.The water used for domestic, irrigation, public supply and industrial purposes amounts to some 7 billion gallons daily at present and will reach 21 billion gallons daily by the year 2000; however, only about one-fifth of the water used is actually consumed, and this, along with the possibilities of water re-use, improves the water supply picture still further.The need for adequate pollution control has accompanied industrial and urban expansion and is an important factor in the extent to which our surplus water is used. In the 10-year period since the formation of the Ontario Water Resources Commission, the cost of water and sewage works constructed in the Province has exceeded one billion dollars. A special effort is now being made to control the industrial pollution situation.Numerous federal and provincial agencies are engaged in hydrologie studies in the Province, providing in-formation of benefit to those involved with water resources management."

Jan 1, 1967

By R. D. Prettie

Wood preservation may be defined as the art of protecting wood from decay. In its broadest sense, however, it includes a much wider field. It might be more properly de-fined as the art of protecting wood from destructive agents, such as decay, insects, marine borers, mechanical wear, etc. The earliest data on record for the preservation of organic bodies is found in Egyptian manuscripts. The bodies which we call mummies were impregnated with antiseptics, of which the principal were natrum (sodium sesqui-carbonate), sodium chloride, and sodium sulphate. After being steeped in the solution, they were subjected to either a boiling or baking process in a bituminous preparation. The first attempts in Europe to preserve timber were made by the Greeks and Romans. They extracted essential oils from the juniper and cypress trees, and either rubbed these oils into the wood they wished to preserve, or bored thousands of small holes in the wood and poured the preservative oil into the holes. The famous statues of Jupiter and Diana were carved out of wood. The ceremony of pouring in the preservative oil by the High Priests was a religious pageant of great importance, of which there are many records.

Jan 1, 1926

By John B. Phillips

The mine is entered by a central vertical shaft, strongly timbered, and containing two compartments-one for the passenger cage, the other for the large skips bringing the ore to the surface. A man-way, for emergencies, is also provided, parallel to the shaft. The cage is a single-deck steel box, carrying about thirty persons; by means of arrangements above and below, it can also hoist and lower materials needed in the workings. Levels are run at intervals of 100 feet. In special cases, where the ore conditions warrant, sub-levels are operated, such as those at 1,113 feet and 1,123 feet (Fig. 7), which are connected by winzes with the 11 th level. One of these was pushed for 40 feet, and then abandoned because it was unprofitable to take up ore of the grade encountered. The ore between levels is removed by stoping. The drifts follow the course of the veins as much as possible, with numerous cross-cuts. Winzes, raises, connections, etc., are blasted out where needed. The main drifts are at least 8 ft. high by about 9 ft. wide. All former narrow drifts had to be widened some time ago, by ruling of the Ontario Department of Mines, to lessen the danger of accidents with cars in the small passages. Accurate plans of the under-ground workings are kept in the office, and extensive surveying is always being done underground to keep the maps up to date, measure the cubical contents of stopes, and so forth. Timber is extensively used in the construction of supports and chutes, and in the sinking of the shaft. Steel and concrete are too ex pensive to compete with timber, which 1s abundant in such sections as have escaped forest tires.

Jan 1, 1926

By James A. Finch, Jason S. Doucet, Cesar O. Gomez

"Exercising control over the physical environment of flotation as a step towards process optimization is the driving force for characterizing gas dispersion in flotation cells, a subject of considerable research and still not fully understood. From an operational standpoint, however, there are just a few variables that can be manipulated to manage gas dispersion on a cell-to-cell basis, the most important being gas rate (superficial gas velocity Jg). Measurements in eight plants demonstrate there is often no strategy for distribution of gas to cells in a bank, i.e., there is no particular Jg profile. Two exercises where Jg profiles were set allowed metallurgical performance to be manipulated and an optimum Jg profile to be selected. To facilitate setting Jg profiles, a multi-unit device based on McGill Jg sensor technology is introduced. Possible directions for gas dispersion management are discussed.INTRODUCTIONThe earliest patents regarding the flotation process ignored the importance of air and in certain cases, steps were taken to eliminate bubbles from the system (Nelson and Smit, 2005). Rickard (1916) described a keen metallurgist who observed better than expected performance and hypothesized that entrained air was enhancing the process. Within a few years of this observation, the basic concept of modern froth flotation was developed whereby air is dispersed into slurry to induce bubble particle contact.As research into flotation advanced, the link between performance and the flow-rate of air entering the cell was established. In the first volume of the International Journal of Mineral Processing, Harris (1974) described the importance of airflow-rate and derived parameters such as the superficial gas velocity (then called the superficial airflow velocity) as being important parameters for cell design and scale-up. Mehrotra and Kapur (1974) presented research suggesting that the rate of flotation was strongly correlated to the aeration rate. McKee et al. (1976) continued to demonstrate the importance of airflow-rate linking it to the entrainment rate of hydrophilic gangue material."

Jan 1, 2006

By D. Wolfe, K. Reid, T. Nunn

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. In order to minimize front-end rejects, and to allow for high throughput, the ore top size at Aurora has been set at a nominal 125 mm. These relatively large lumps have a significant effect on both pump performance and pipeline pressure gradient. Current design methods underestimate the solids de-rating effect of lumpy slurries in pumps, and do not accurately describe the distribution or magnitude of the lump effect on pipeline pressure gradient. Data from the Aurora hydrotransport systems has been compiled, to quantify the effect of lumps on the pump head ratio and pipeline pressure gradient, and how this effect changes as lump ablation occurs along the length of the pipeline. A model has been built, using a logarithmic curve, which predicts the effect of 125 mm lumps on pipeline pressure gradient as a function of velocity and the distance from the start of a hydrotransport pipeline. This model is applicable only to Aurora hydrotransport operation, but similar models could be developed for other operations using the same methods. Using accurate pipeline pressure gradients and pump head ratios when designing future hydrotransport pipeline systems will help improve their reliability and operability."

Jan 1, 2014

By J. S. Edwards

The ISASMELT? process is recognized worldwide as a modem, flexible, environmentally-friendly and low capital cost smelting technology. Due to the inherent simplicity, and the advanced process control that has been developed, personnel become competent within weeks of being introduced to the ISASMELT? technology. This compares with the years required to become proficient with alternative technologies. Copper smelters in Australia, USA, India, China, Peru and Zambia have installed ISASMELT? technology under licence from Xstrata Technology. In the secondary copper business, plants in Belgium and Germany are processing copper and/or lead materials in ISASMELT? furnaces in a two stage process. In a single furnace smelting is followed by converting. Both plants have exceeded design capacities and are continuously improving their performance. The next evolutionary step for the technology is the implementation of the continuous copper converting process on a commercial scale. The present work describes the design status of the continuous converting process - ISACONVERT?.

Jan 1, 2007