Search Documents

By V. I. Lakshmanan, D. A. Mackie

"1. INTRODUCTIONIn the past two decades, low-grade gold and silver ore bodies in the United States have been exploited by heap leaching, primarily with sodium cyanide solutions. This method has proven to be a viable alternative to conventional milling due to its low capital and operating costs. Successes have been made, particularly in Nevada, where ores are well oxidized and the climate is conducive to this method. in recent years, heap leaching has been tried in northern latitudes with some success, however, in using this method, operators face more severe limitations than do their neighbours to the south.This paper evaluates the limitations of heap leaching with particular emphasis on northern climates and introduces an alternative method to recover precious metal values in a continuous vat. This proprietory technology, known as the Mackie Vat Leaching Jig, shows promise, with improved gold recovery and potential to operate in cold climates.2. WHAT ARE THE LIMITATIONS TO HEAP LEACHING?Heap leaching of non-refractory ores is subject to the following limitations:1. Minimum amount of free gold and nuggets in the ore.?. Minerology of the ore--accessibility of gold to lixiviant.3. Minimum particle size and size distribution of crushed product to allow percolation of lixiviant through the heap.4. Minimum amount of clays or clay-like slimes that can cause coating of ore particles and channelling of lixiviant.5. Minimum strength of ore particles or agglomerations to allow economic height of heaps to be built.6. Amount and suitability of real estate.7. Amount and type of precipitation.8. Ambient temperatures.9. Possible poorer lixiviant diffusion.10. Possible lower oxygen content in dissolved cyanide solution with higher heaps, particularly with ice and snow cover."

Jan 1, 1989

By Joseph J. Mgumbwa

Pillars are any structures left between two or more underground openings. The stability of pillars is normally considered to depend on shape (defined by width to height ratio), rock mass strength, extraction ratio, in situ stresses and the gross structural features (i.e. joints, contacts, faults etc). Recent experience has shown that pillar stability is also controlled by the relative orientation of the orebody with respect to the in situ principal stress. In inclined orebodies, pillars are loaded in compression and shear, thus creating unsymmetrical stress distribution. Failure mechanisms of these pillars are little known. This paper investigates the failure mechanisms of pillars under shear loading. Two dimensional elastic numerical modeling was used to examine the behavior of pillars in different orebody inclinations relative to the major farfield stress orientation. First, the paper reviews pillar design approaches including the empirical pillar design chart and uses numerical modeling to investigate the effect of the major farfield stress orientation on pillar stability. It is concluded that the empirical pillar design chart be used with caution, and that for orebodies under shear loading mine planning and design should take this into consideration since such geometrical orebody/stress relations put mine structures at higher risk of instability.

Oct 1, 2010

By R. E. Whitehead

"Alkali/alumina and MgO/alumina molar ratio plots graphically portray both chemical and mineralogical changes accompanying potassic, phyllic, argillic, chloritic, and alunitic alteration of quartz monzonites and granodiorites hosting porphyry (as well as lode and greisen) ore deposits. The molar ratio plots can be used to identify different types of alteration. In most cases, the identification based on molar ratios coincides with petrographic data. In those instances where the molar ratio and petrographic identifications do not agree, the mineralogy might need to be re-examined. Hydrothermal alteration studies using trace elements could benefit from the application of complementary alkali/alumina molar ratio plots.Le diagramme des rapports molaires alkali/alumine et MgO/alumine illustre clairement les changements chimiques et minéralogiques qui accompagnent les altérations potassique, phyllique, argillique, chloritique, and alunitique des monzonites à quartz et des granodiorites encaissant les gîtes de type porphyrique, ainsi que des veines et des greisens qui leur sont associés. Les diagrammes de rapports molaires peuvent être utilisés pour identifier divers types d’altération. Dans la plupart des cas, l’identification basée sur les rapports molaires est en accord avec celle basée sur les données pétrographiques. Là ou il y a désaccord entre les rapports molaires et les données pétro-graphiques, il peut être nécessaire de réexaminer la minéralogie. Les études de l’altération hydro-thermale accompagnées d’une étude des éléments traces auraient avantage à utiliser un diagramme des rapports molaires alkali/alumine."

Jan 1, 2009

"INTRODUCTIONThe Kidd Creek Concentrator is located 28 kilometers east of the city of Timmins, Ontario. Two types of ore are treated; 'A' type, a copper-zinc-low silver ore producing copper and zinc concentrates, and 'C' type, a copper-lead-zinc-high silver ore producing copper, lead and zinc concentrates.The ore is processed at a combined rate of 12,400 metric tonnes per day through four parallel grinding and flotation divisions. Three divisions treat the 'A' type ore and the fourth treats the 'C' ore. Each division is fed from its own fine ore bin.This paper reviews the grinding section with specific emphasis on grinding media consumption and the factors affecting it as related to 'A' type ore. At Kidd Creek there was an awareness that grinding media consumption varied on a weekly and monthly basis. The reasons for this variation was usually attributed to ore hardness as evidenced by short term variations in the circuit feedrate and head assays. However, there has been a diversity of opinion published in recent years regarding the factors contributing to steel consumption. This initiated a study of historical Kidd Creek operating data, from the period 1970 to 1986 inclusive, to determine the effect of various operating parameters on media consumption. The results of the study could then be used as a baseline for future media consumption testwork."

Jan 1, 1988

By Jr. Blanchette, Claude Bazin, Paul Blatter

"Reporting of the gold production during a month implies to estimate the mass of gold that is processed by a mill, recovered as dorés, lost to the tailings and the change of gold inventory within the plant equipments. Carbon in pulp and/or carbon in leach tanks may contain gold inventory as large as 72 000 g (2 200 troy oz) of gold which needs to be estimated from measurements obtained from sampling the material contained in a tank. Sampling and analysis introduce measurement errors that could be systematic and/or random. This paper examines the effect of measurement errors on the estimation of the gold inventory and on the variation of the inventory in the carbon in leach tanks of the Agnico-Eagle Mines Limited Lapa concentrator. Results of the analysis demonstrate that the inventory is measured with ±10% reproducibility, while the variation of inventory used for mass balance is known with ±300% reproducibility.INTRODUCTIONThe preparation of a production report implies to reconcile measured data with the constraint of material balance over the considered period of production. The sampling and data reconciliation problems were recently reviewed by Morrison (2008) and Jansen (2009a; 2009b). Typically a production report is prepared to cover a period over which the mass conservation hypothesis can be considered valid. In gold processing plants, the change of inventory can seldom be neglected and plays a significant role in material balance calculations. This is particularly true for circuits using carbon adsorption, where the complete cycle of carbon is measured in days.In a 2000 t/d gold ore processing plant, the inventory can be as large as 140 000 g of gold in gravity concentrator bins, carbon in pulp tanks and in the electrolysis circuit. This is equivalent to the mass of gold that fed the circuit during 10 days of operation with 7 g/t feed assays. The change of inventory may therefore strongly impact the production figures and especially the plant recovery at the end of a week or a month. Despite the financial impact associated with gold inventory, few publications are devoted to the subject. Bruington (1991) and Morrison (2008) discussed the problem and stressed the need for the development of reliable methods to estimate the gold inventory in carbon in pulp or carbon in leach circuits."

Jan 1, 2011

By R. Jolicoeur, J. F. Jackson, M. A. Green

"The design, construction and commissioning of Kiena Gold Mines Limited's new mill was completed in 15 months ending in September 1984. Rated at 1250 tonnes per day the mill incorporates the latest innovative technology such as semi-autogenous grinding, carbon in pulp, pressure stripping and induction furnace refining. The mill is housed in a pre-engineered building with the leach tanks and thickeners located outdoors in spite of the intense winter cold. 1.0 INTRODUCTION AND HISTORYThe operations or Kiena Gold Mines Limited are located in Dubw1sson Township, approximately 10 Km west of Val d'Or, in the Abitibi region northwestern Quebec. Comprised of 59 mining claims covering 1214 hectares, a large portion of the mining property is overlain by the waters of Lac de Montigny. Sometime between 1911 and 1914 Barney Parker discovered gold in a shear zone on an island in Lac de Montigny that now bears his name. The first shaft the Parker Shaft, was sunk in 1936 from the island to a depth of 136 meters but owing to the known veins being of limited extent and the onset of the Second World War operations were terminated in 1940. In the early l960 1 s exploration drilling indicated an orebody of 4,500.000 tonnes at 6.3 grams of gold per tonne. A causeway was built to link the island to the mainland in 1963 and a new 3 compartment shaft was sunk to 403 metres. The orebody was further delineated and the ground conditions within the orebody and surrounds were evaluated.At the end of 1965 the property was placed on a care and maintenance basis as a mining operation would be marginal with gold selling at $35 per ounce."

Jan 1, 1986

By Gregory A. Johnson

Operations and Maintenance departments have long had an adversarial relationship. The widespread evolution and adoption of modern management techniques such as Reliability Centered Maintenance (RCM) and Lean Production however has driven interest in working co-operatively to optimize overall plant performance. Mining and minerals operations have long adopted RCM in maintenance, and are now adopting Lean throughout the organization. Modern management initiatives like these explicitly call for co-operation between the two disciplines of maintenance and production and many advances have been made in the realms of people and methodology. One area that has lagged behind in supporting these developments however is information systems. Enterprise Asset Management (EAM) systems in maintenance and newer Manufacturing Execution Systems (MES) in operations have not been truly integrated in the way needed. Complicated plants, different software architectures, continually changing conditions and many variables have lead to systems problems which have contributed to the maintenance/operations divide. Master data synchronization (the ?plant tree?) and integrated reporting of real-time data with transactional data are just two of the issues that are being solved by new approaches in information technology including web services and service orientated architectures. New technologies are coming on-stream to enable the final ?bridging of the gap?.

Feb 1, 2008

By G. A. Kosick, G. S. Dobby, O. Matwijenko

"A 100 kg/hr portable flotation pilot plant has been operated at Kidd Creek Mines with the objectives of:(a) determining performance expected by column flotation circuits on primary zinc and copper cleaning, and (b) evaluating column flotation circuit configurations.The self-supporting pilot plant, owned by Minnovex Technologies Inc. and operated by Minnovex and the University of Toronto, consisted of three 16 cm diameter by 6.5 m high columns and a bank of four Denver No. 7 cells. It was configurable to any arrangement using these four (or fewer) units. The columns were controlled through the use of multiple pressure transducer measurements. This paper presents the approach to testing and the results of more than 70 circuit tests. INTRODUCTIONThe integration and retrofitting of flotation columns within existing mechanical cell flotation circuits is becoming a common occurrence. The correct approach to this integration, however, is often difficult to define, due to a scarcity of previous experience and the difficulty in predicting column circuit performance. In most cases, the effect of column implementation has been experimentally assessed using a single pilot column, with the consequence that selection of an appropriate circuit to implement is difficult. Important considerations are the impact that column water addition will have on the existing operations, and the differences between mechanical cell and column performance in integrated cleaning circuits.To address the problem of circuit selection a portable flotation pilot plant, consisting of both columns and mechanical cells, was designed and constructed by Minnovex Technologies. The pilot plant was structured for complete flexibility of circuit configuration, with the intent to provide a means by which both research and plant personnel could determine the best possible column circuit configuration for a given application."

Jan 1, 1990

By Andy Fortin, André Vien, Christophe Bouché, Jeff McKay

"The technology and equipment design of the Twenty-first Century permit us to exploit low-grade ore bodies with milled tonnages reaching 300,000 tpd. Because of their substantial operational costs (energy, wear parts, etc) and precarious economic situations, the operations of today must maximize their metallurgical performance.The implementation of an Expert System becomes a logical avenue to pursue in view of increasing plant performance.Many operations, following the implementation of an Expert System, meet the objectives they determined before its integration; such as increased tonnage, stability, decreased costs, etc. However, they often cannot develop the full potential of the system due to certain factors that have been neglected or omitted during the implementation of the system.Three main elements have been identified during the implementation phase at INMET Mining Troilus Concentrator: 1- Instrumentation & Control 2- Software 3- Integration. Even though they have been clearly identified, these elements are often neglected due to lack of resources or lack of comprehension on the part of the operations personnel. This document will demonstrate, based upon our experience at Troilus and that of Metso Minerals, that we can identify and handle many factors which influence the profitability of the Expert System, for both short and long-term process control improvements.INTRODUCTIONThe Inmet Troilus Mine is an open pit mine, situated 175 km north of Chibougamau in the province of Québec, Canada. The mill, which started production in November of 1996, was originally designed to treat a gold – copper ore at a rate of 10,000 tpd.In early 1998, the mine plan called for a pit pushback and decreasing head grades for the following two years. With the price of gold nearing decade lows, the Troilus project was facing a major economical setback. There was a sense of urgency to reduce operating costs below the market price of gold. The mill team presented a project to management calling for an increase in mill throughput while minimizing capital expenditures and operating costs. This idea was supported by the existing mine plan, which called for a mine cut-off of 0.7 g/t Au and stockpiling low grade 0.5 g/t material for future milling."

Jan 1, 2003

By Michel Brissette

"To recover more valuable ore and considering the complexity of minerals, the needs to grind finer is increasing. To reach the desired fine grinding targets, using the existing grinding media size, the energy consumption is increasing exponentially. As already proved at this conference, small grinding media represents the best potential to improve grinding efficiency. How do the small grinding media perform in industrial grinding mills?The use of small grinding media in regrind mills proved that finer grinding can be achieved at lower energy consumption. In ball mills, smaller grinding media versus 25 mm media generate a power saving from 10% to 44%. In vertical stirred mills, the power saving increases from 20% to 60%. More potential savings have been identified.For the same operating conditions, how a vertical stirred mill is performing compared to ball milling? In regrind application, a vertical stirred mill with small media (5-12 mm Millpebs) will require at least 62% less energy than a ball mill charged with 25 mm grinding media.INTRODUCTIONIn some mining applications, fine grinding is needed to liberate further the valuable ore. The purpose of regrind mills is to achieve the last stage of grinding before final flotation stage: the cleaners. In part because of high prices of small grinding media as well as availability, the most widely used size of grinding media is 25 mm.When calculating the recommended ball top size from Bond’s formula (Bond, 1961), the size for regrind applications is much lower than 25 mm. Today, the barrier for small grinding media is broken. They are best suited in regrind application. The size of grinding media is one of the most important variables affecting the mill efficiency (McIvor, R., 1997; Nesset, J.E., Radziszewski, P., Hardie, C. & Leroux, D.P., 2006).Conventional ball milling was discarded for fine grinding because of its very poor energy efficiency (Zheng, J., Harris, C.C. & Somasundaran, P., 1994; Yan, D.S., Freeman, M. & Dunne, R., 1995). Therefore, new technologies as stirred mills were developed to grind finer more effectively. Three fundamental questions should be asked. What is the best fine grinding technology? What should be the best media size to use? Is it possible to grind finer by using less energy with the existing regrind equipment?"

Jan 1, 2009

By Frédéric Flament, Luc Lachance

"The important task of metallurgical accounting that used to be done manually is being more and more automated. Currently available solutions can generate accounting reports without human intervention or almost. However, the practical conditions for fully delivering the promised benefits of those solutions are sometimes overlooked either by end-users or by integrators. The mere fact of filling reports with values satisfying several constraints such as mass conservation constraints does not, by itself, ensure a high quality metallurgical balance. Since managers make decisions based on these reports, it is logical that the metallurgical balance performance be monitored and retrofits be made if necessary. Such retrofits may involve modifications to the measurement strategy or the reduction of the spatial resolution of the material balance model. This requires an estimability and redundancy analysis (ERA) tool to assess the feasibility of the modified model. Since determining by hand the estimability and redundancy of a set of non measured and measured variables is not trivial, even for a medium-sized mineral processing plant, a dedicated ERA tool brings valuable assistance to the metallurgist in charge. The present paper aims first at explaining how a state of the art metallurgical balance is a key enabler for the adoption of a smart process plants paradigm (SPPP) in mineral processing. Then, the fundamentals behind the building of an ERA algorithm are introduced and illustrated by two examples. Finally, the role of an ERA tool in achieving state of the art metallurgical accounting and how it contributes to delivering additional value are discussed.INTRODUCTIONThe Smart Process Plants Paradigm (SPPP)Mineral processors have seen an increase lately in external pressures toward operating performance improvements. Indeed, the globalization of the mining business is a key driver to becoming more productive, more responsive to market changes, to improving corporate governance and reporting standards. Furthermore, mineral processors are also expected by their neighbouring communities to continuously improve their sustainability score. These current pressures differ somewhat from the past ones in leading to a larger than ever number of conflicting constraints that plant managers must concurrently satisfy while maximizing plant profitability. It is in turn not surprising that this context requires actions involving more real-time collaborative actions between more people in more places than ever before."

Jan 1, 2011

By J. P. Sancho, L. F. Verdeja, J. I. Verdeja

"This paper analyzes the present state of the different processes competing to keep their market shares within the future iron and steel business sector.The continuous transformations in the steel making process are also studied here. These transformations have happened especially during the two last decades obviously favouring steel price, properties, quality and environmental compatibility in the new millennium. IntroductionIn the early 1980s, world steel production reached a historic figure; specifically in 1982, the amount was 645 Mt (Verdeja et al., 1993). This might have been one of the reasons why the United States, Japan and the European Community drew up a declaration of principles after which the leading industries and sectors in the following century’s development would be: advanced materials, also known by the very diffuse term of new materials; information technologies; and biotechnology (Eager, 1998).On the threshold of the 21st century, it can be inferred that information technologies (computers and telecommunications) have progressed spectacularly. Nevertheless, there have been downsides too; technology develops so quickly that after a few months the products are obsolete. Environmental problems may also appear in a few years due to storing so many useless devices. At the same time, the achievements of biotechnology did not meet the optimistic forecasts made in the early 1980s.On the other hand, it is also curious that some solutions for the environmental problems generated by star technologies of the new millennium, such as computers and biotechnology, are closely linked to the iron and steel industry. For example, blast furnaces in Germany and Japan are prepared for burning residua by introducing polymer materials from computers and other electronic prepared devices through their tuyeres, while cement tube furnaces can destroy any organic residua from different origins."

Jan 1, 2002

By DALE MacGREGOR, VERA TUREK

lndusmin Limited acquired the St. Donat quartzite deposit in 1967 to produce high-quality silica for use in the sandblasting and silicon carbide industries. The quartzite, of Grenville age, is highly friable and porous. This is due to numerous small, kaolinite-coated cavities in the quartzite; the cavities were formed through leaching, probably by rising hot solutions.

Jan 1, 1984

"It is projected that the reactivity of acid generating tailings and waste rock can be minimized by reducing the access of oxygen by placing these materials under water in natural or manmade lakes. A project under the MEND and B.C. AMO Task Forces has been in progress for four years to evaluate active and historic tailing sites in B.C. and Manitoba. The sophisticated geochemistry studies conducted on the interstitial pore water has illustrated encouraging results which are discussed. The additional studies which are needed to complete the scientific database for the study sites, for achieving regulatory and public approval and for the engineering of application of this method of control are outlined.IntroductionWorld wide research effort is in progress to find the solution to the acid mine drainage problem. A great deal is known about acid mine drainage but much work is required to find economic and effective approaches to the problem. Two coordinated programs have been initiated recently in Canada: the National Mine Environment Neutral Drainage (MEND) program and the British Columbia Acid Drainage Task Force.Disposal of tailings materials under a water barrier such as a natural lake, is thought to be one solution to prevent acid generation by preventing oxygen and bacterial action on the sulphide surfaces. The deposition of reactive tailings materials under water in natural lakes has been used historically at various mines in Canada. However, there has never been a thorough review of the long and short term impacts of historic sites which may provide crucial information to understand the physical, chemical and biological processes which are taking place.This paper provides a general overview of a series of studies which examine the general biophysical characteristics and the sediment geochemistry of four lakes where subaqueous disposal has been or is currently being used for acid generating tailings. The subaqueous disposal studies have been conducted from 1989 through 1991 and were initiated and supported by both research task forces. The objectives of this paper are to summarize the history and the background information of the studies conducted, the general results obtained from each lake, an overview of the major collective results and the additional work which is required to achieve the final objective of developing criteria for applying this technology in the industry."

Jan 1, 1992

By R. E. McElvain

"Hydraulic transportation of solids in suspension with water or other carriers, such as oil is becoming more practical as economic situations develop with respect to the railroads and other carriers. Of significant importance, is also the increased size of the major operations and the total impact of larg- er tonnages and more critical sources of supply.There are several means of imparting energy into the solids and directing the material down a pipeline, but the centrifugal pump is emerging as the most practical piece of equipment when considering relatively large flows and recent development. We can now handle relatively high densities without interruptions. This provides the mining and transportation fields a more economical means of lifting and transporting coal and other mineral products.Equipment & MethodsWarman International has developed several methods of alternate PDP against high heads. We have, at least for the present time, shelved our pump which uses clear water to slurry method and have placed our major emphasis on the full development of the centrifugal pump. I personally see several similarities on the alternate reciprocating devices as compared with the steam piston type engine versus steam turbines. The centrifugal pump comes into its most advantageous position at about 2000 GPM and can also show advantages by means of increased mobility, when driving tunnels and in other difficult operations when considering the total economic results. We now have some interesting d<:ta on one 5 mile raw silica sand line designed for pumping at 200-400 tons per h:mr. This is a separate subject on a ""simplified approach to slurry transport"" and paper has been prepared for the Hydrotransport 5 proceedings in Germany this Spring. Reference 1 may be of interest to those who want to delve into the subject further, and I also have some advance copies of this paper."

Jan 1, 1978

By Y. O. Fortier

"ForewordTHE Arctic Archipelago and northern Greenland contain an orogenic region that is as much as 300 miles wide and over 1,400 miles long. It occupies much of what was formerly classified with the Arctic Plains and grouped with other plains and lowlands of Canada as one main geological division. It is proposed that this folded region be designated the Innuitian Region and be recognized as one of the main geological divisions of Canada.Canada's main geological divisions (see Geological Survey of Canada, 1947) have been considered as consisting of a central shield, largely surrounded by plains that separate it from eastern and western mountains. The plains include the Interior Plains, the St. Lawrence Lowlands, the Arctic Plains or Low-lands, and the Hudson Bay Lowland, which is in the central part of the Shield. Plains and mountains are, strictly speaking, physiographic terms, but because mountains are generally folded regions and plains are generally made of undisturbed strata, such terms are useful vehicles to express the fundamental make-up of the land. Nevertheless, it is preferable to use the terms Appalachian and Cordilleran 'Regions' rather than 'Mountains', as those geological divisions are not exclusively made of mountains.Because of the lack of more definite information, the 'Arctic Plains' have included, in the past, regions with plateaux two to four thousand feet above the nearby sea, mountain ranges reaching approximately 10,000 feet above sea level, and regions of folded strata."

Jan 1, 1955

By S. Pinard, J. MacLellan, G. Ehlert

"The Kidd Creek concentrator is looking actively for alternative technology as means of reducing operating costs in their concentrate handling section. The use of pressure and vacuum filters to eliminate the multiple hearth dryers would have the most beneficial effect. The dryers which constitute the greater portion of concentrate drying costs consume about 35,000 m3 per day of natural gas.After the evaluation of various filters by Kidd's technology group, it was clear that, because of the low final moisture requirements of 5.5 to 6% H20, few filters were able to achieve this target economically. Lately attention has focused on the Andritz hyperbaric filter. Testwork has shown that target moistures can be achieved with an appreciable reduction in operating cost.1.0 INTRODUCTIONThe Kidd Creek Concentrator is located 28 kilometers east of Timmins, Ontario. The ore is hauled by the Kidd Creek Railroad to the concentrator where it is milled to produce separate copper and zinc concentrates.Projected concentrator feed for 1991 is 3,750,000 tonnes of ore grading 3.3 % Cu and 4.7 % Zn. The concentrate production is expected to be 458,080 dry tonnes of copper concentrate at a grade of 25.7 % Cu and 265,020 dry tonnes of zinc concentrate at a grade of 54 % Zn.Currently, there is active investigation toward cost reduction through implementation of new technologies. One area which has been extensively evaluated is the concentrate dewatering and drying section. In that section, the multiple hearth concentrate dryers represent the largest source of operating costs, mainly through maintenance and energy costs (electricity and natural gas). The replacement of these dryers with filtration technology that could produce the required concentrate dryness would represent substantial savings.In September of 1990 filtration testwork carried out by Andritz Ruthner showed that Kidd Creek copper and zinc concentrates could be filtered to below 6 and 8 % moisture respectively. In late May 1991 the laboratory testwork was duplicated on siteand one month later a 5 m2 pilot filter was tested on site. Based on the pilot test results, an economic evaluation was performed. It indicated that a reasonable payback could be realized if hyperbaric filters were to replace the existing concentrate drying section."

Jan 1, 1992

The Stability Graph Method is widely used in Canadian underground hard rock mines for open stope support design and is frequently used in the mine planning phase to assess the viability of stope geometries and to determine maximum permissible spans. The Method is well accepted due to its simplicity and suitability to a wide range of mining methods requiring the use of sublevels to access and extract the mining blocks. While this Method is reliable in situations where the maximum induced tangential stress creates adequate compressive stress keeping the face in a state of confinement, the Method fails to reflect the effect of low confinement caused by lower compressive stresses and instances where tensile stresses are developed. In this paper, a new Rock Stress Factor, A?, an update to the original Rock Stress Factor, A, is proposed, which will reflect the impact of low confinement or overstress regime on critical face stability. Two case studies, based on two Canadian operating gold mine shows that using the new Rock Stress Factor A? to predict the stability of stope hanging-wall and footwall gives better agreement with the CMS survey results, compared with the prediction using the original rock stress factor.

May 1, 2011

By R. Haecker, S. Bajic, R. Thorpe, A. Palko, M. Kalstrom

"Historically, mineral processors have used inferential data like plant instrumentation, assays, and grind sizes to monitor the performance of their plants. The ability to monitor the minerals themselves on a daily basis has eluded all but the very largest and richest of operations. The advent of a new generation of compact, robust, and user-friendly SEM-based automated mineralogy systems looks set to accomplish this, aiming to bring daily mineral monitoring of plant performance within the reach of all mills from mid-size upwards. This paper describes the use of this machine at Greens Creek Mine, a 2.5 ktpd Ag-Au-Pb-Zn operation with a complex flotation flowsheet. During the trial, the machine provided turnaround from sample collection to reporting averaging 24-36 h for key daily samples. All equipment was located within the compact mill, and proved highly reliable despite the challenging environment. Turnaround time was fast enough for metallurgists to understand, and, where possible, respond to ore and process changes while they were still happening. The plethora of data generated was filtered to a simple report whereby mill management could quickly absorb key daily mineral-based performance indicators. This paper will describe how the data was used to understand the key drivers behind metallurgical efficiency at Greens Creek, and how metallurgists began using the information to enhance daily mill performance."

Jan 1, 2014

By T. Schmidt, J. Merza

"This study considers two lead/zinc/silver orebodies which have historically had a problem with pyrite, pyrrhotite and sphalerite contamination in the lead circuit. The problem was previously addressed with high dosages of sodium cyanide as the primary depressant. However, large amounts of cyanide led to environmental problems in the effluent, especially during winter months. The objective was to reduce cyanide consumption while maintaining or improving overall lead grade and recovery via the reduction of the undesirable sulphides.Extensive laboratory and mill testing was necessary to determine the optimal operating parameters for continuous plant application. Evaluation of data received from this testing has shown that selective addition and optimization of the dosage of Unimax SD100 to specific areas of the flotation and grinding circuits has resulted in improved Pb grade and recovery. Parameters such as pH control, regrind operation, the cyanide/Unimax ratio and sulphide mineral content may also affect the performance of the depressant. Each factor is discussed and optimal operating conditions were determined based on the testing.Results are presented for two case studies. Both indicate that Unimax SD100 improves the lead grade/recovery curve by increasing iron and zinc rejection while reducing cyanide consumption and the resulting environmental concerns. 1. Hart"

Jan 1, 1992