Search Documents

By Donald L. Mordell

Introduction A very large part of the world's fuel resources are in solid form, as various grades of ?coal, but an increasing proportion of fuel demands on this Continent and else-where are having to be met by liquid fuels. Convenience and, in many cases, cost weigh heavily in favour of the liquid: fuels, and there are many fuel burning applications where the use of coal would be impractical, such as for automotive or air transport. By extrapolating the present trends one might conclude that, in future years in Canada and the United States, coal will be used only in a few power stations close to coal fields. If such a state of affairs should arise, it will obviously prove embarrassing to those accustomed to make their livelihood from the winning and marketing of coal, but it is perhaps not so obvious that it must also prove an embarrassment to the nation. The major reasons for this are two in number. Firstly, if present coal production is to be replaced by oil production, a large capital expenditure is necessary, which must inevitably be paid by the consumer; and secondly, in times of emergency, large amounts of oil fuels are required for military purposes which cannot be achieved with solid fuels. It is obviously unwise, therefore, to discontinue the use of coal for those non-military jobs that it can do. If we examine the major fuel markets we find that there are three: Domestic heating Steam generation Transport by air, sea, and land For domestic heating, the extreme convenience of oil, in spite of its greater cost, has captured much of the coal market.

Jan 1, 1952

By B. Chambers, M. Yunovich

"Corrosion monitoring is commonly used in a variety of industries as a means of effective corrosion control programs to extend the life of the asset and ensure safe operation of the facilities. The majority of the monitoring tools have limitations and tradeoffs – e.g., sacrificing the longevity of the probe for higher measurement resolution. Linear polarization resistance (LPR) probes have the advantage of providing the operator with accurate, real-time corrosion rate data; however, the probes can only be deployed in conditions where the measured environment possesses certain minimal conductivity. In many instances, utilization of LPR probes in conditions with intermittent wetting (for example, conditions where the temperature fluctuates above and below the dew point) presents a challenge. To address this limitation, a special-design cooled corrosion probe has been developed, commercialized and integrated into the distributed control system in the plants. In addition to high-accuracy measurement of corrosion rates, the probe allows for monitoring of pitting corrosion. The most innovative feature of the probe is the cooling circuit, which brings the temperature of the sensors below the dew point, forcing precipitation of moisture and thus permitting corrosion measurements. Additionally, the probe was found to be well-suited for monitoring corrosion in crude distillation unit (CDU) overhead space, where condensation of hydrochloric acid may take place at relatively high temperatures, which would require relatively moderate amount of cooling to be imparted to the probe sensors. This paper presents laboratory-based data from a test simulating CDU refinery environment. A case study is presented to demonstrate how the cooling probe can be effectively used in the plants for corrosion monitoring.INTRODUCTIONConventional corrosion-monitoring techniques such as weight-loss coupons to assess corrosion damage are commonly used in plants1. However, the use of coupons is not only labor-intensive, but also does not deliver real-time corrosion data, thus effectively serving as a “backwards-looking” monitoring tool. Linear polarization resistance (LPR) probes have the advantage of providing the operator with accurate, real-time corrosion rate data; however, the probes can only be deployed in conditions where the measured environment possesses certain minimal conductivity."

Jan 1, 2012

By D. W. Li

Due to the ultrasonic testing and mechanical wind speed sensor have high requirement for the environmental of the coal mine, the charge induction wind speed detection method based on wavelet analysis is proposed. The same wavelet disturbance detection method is used at a fixed distance to obtain an induction signal to obtain a pass time, and then calculate the magnitude and speed of the wind. Simulation and verification experiments show that the method has application across a wide range of test speeds (up to 60 m/s). The metal probe causes little pipeline flow field interference. The method is particularly well-suited to dusty environment, and does not cause dust deposition through long-term operation. It can be widely used in coal mines for point wind speed continuous online testing.

Aug 1, 2013

By A. L. Irwin

THE problem of compensation for labour is probably the oldest and most complicated one in history. The wage that a man receives is possibly the most concrete thing he gets out of his job and, rightly or wrongly, is generally considered by him to be the most important item in connection with his daily work. How today workers in an equitable way has been the study of industrialists for many years, and a great number of ideas have been tried out in an effort to arrive at a reasonable solution of the question. The idea of establishing a measuring stick for various types of work has intrigued industrial management for a long time and, after considerable study, the principle of Job Evaluation has taken form unti1, at the present time, it is becoming increasingly useful to industry at large. Job evaluation is a plan which is used to determine the relative worth of occupations by means of arbitrary measuring scales. These scales are developed for individual industries and are generally 'tailor made' for each particular case. There are as yet no absolute methods of measuring the work done by human beings and, as a result, one has to depend on comparative values to arrive at conclusions. However, job evaluation has provided us with a basis of negotiation for wage rates which is more satisfactory than mere guess work or persona! opinion. It supplies a common ground for discussion which is understandable by all taking part and ensures that thinking with regard to wage setting is carried out along standard lines.

Jan 1, 1943

Mercapto organic compound SDMP was used as a depressant for separation of copper activated marmatite from pyrrhotite in the presence of butyl xanthate. Flotation results show that SDMP has strong depressing effect on pyrrhotite recovery in the absence and presence of copper ion, but has promotional effect on marmatite recovery when added together with copper ion. The flotation test of mineral mixtures shows that copper-activated marmatite could be separated efficiently from pyrrhotite using SDMP as depressant. Infrared adsorption spectra demonstrate that SDMP has a strong adsorption on pyrrhotite surface through its functional groups such as ?SH, -S03.

Jan 1, 2006

By Tom Gaines, G. S. Brant, J. G. Debanne

"AbstractThe Bonnie Glen oil field, one of Canada's largest, lies about fifty miles southwest of Edmonton, Alberta. One hundred and thirty-eight wells have been completed in this field since its discovery in January, 1952. Five different procedures have been used in completing the producing wells.The reservoir is an Upper Devonian biohermal reef with good porosity and uniformly high permeability. The top of the reef is quite flat but the flanks slope at angles approaching 20 degrees from the horizontal. The reservoir has a gas cap with a maximum thickness of 400 feet, an oil column of 300 feet, and a :porcus aquifer of over 300 feet. The reservoir pressure is now 2,400 pounds per square inch gauge at datum ( -4100 M.S.L.).Because of the high permeability and the high •pressure, lost circulation and resultant blowouts are a particular hazard in drilling at Bonnie :Glen field. To reduce the dangers of blowouts, it is general practice to run casing to the top of the reef. If the reef is encountered 'high' it was usual practice to run a liner and perforate for completion. Wells penetrating the •reef below the gas/oil interface were either completed in open hole or through casing perforated opposite the oil pay, with the former method more frequently used. Eight wells were completed by the Humble-Otis permanent-type completion, and recently five high wells were completed open hole with the gas •cap exposed. This latter completion, 'tubing submergence', has proved highly satisfactory thus far.The open-hole type of completion is cheaper than the liner perforation method and results in better well performance. More experimentation and data are needed before the tubing submergence method can be recommended unqualifiedly. but all evidence thus far favours its use in reef reservoirs."

Jan 1, 1955

By P. D. R. Maltby

"The Canadian Institute of Mining and Metallurgy has undertaken to host the XIV International Mineral Processing Congress to be held in Toronto at the Royal York Hotel from October 10 to 16, 1982. The theme of the Congress will be ""Worldwide Industrial Application of Mineral Processing Technology."" The program will include 10 sessions and numerous field trips to the different mining areas of Canada.For prospective authors, the preliminary program includes sessions on,1. Flotation - plant practice, equipment design, simulation, control and economics.2. Comminution - plant practice, equipment, design, simulation, control, wear, energy consideration and economics.3. Round table seminar on large grinding mills.4. Round table seminar on modern and future plant design.5. Mineral processes to recover precious metals.6. Mineral processes to recover energy minerals (coal, uranium).7. Mineral processes to recover industrial minerals.8. Round table seminar on the environment and ecology and how the different countries cope with associated problems.9. Materials handling with an emphasis on agglomeration techniques ereconentration methods, solid-liquid separation.10. Open session to deal with topic emerging from general demand."

Jan 1, 1980

By M. A. Halim, V. I. Lakshmanan

Recycling is one of the key elements for sustainable process development for the recovery of value-added products and reducing environmental impact. Process Research ORTECH Inc. has developed several innovative and sustainable technologies, which minimizes the use of water, and chemicals for the recovery of gold, vanadium and gallium from secondary sources by maximizing the recycling of reagents, and reuse of water from process effluents.

Jan 1, 2015

By D. V. Dorling, J. T. Bowker, J. A. Gianetto

Over the last few years, interest in the development and construction of large diameter, high pressure pipelines from the Mackenzie Delta in northern Canada and Alaska's North Slope has steadily increased as a result of the projected decline in recoverable natural gas from existing reserves in western Canada. The success of such enormous pipeline projects, which will require utilization of a strain-based design approach, is largely based on successful application of high strength line pipe steels, such as X80 and X100. To fully realize the economic benefits of high strength steels, welding processes and procedures must be developed to ensure that the requirements for high strength and good low temperature toughness are confidently obtainable in field girth welds used in the construction of such pipelines. This study aims to provide a better understanding of the factors that control weld metal strength and toughness for a series of mechanized X100 girth welds produced using a range of narrow-gap gas-metal arc welding procedures. The attainment of high yield strength (> 810 MPa) is considered to be an important target to ensure overmatching strength relative to the longitudinal property distribution of X100 line pipe steel. Some factors that have been considered in this evaluation include influences of gas-metal arc welding process variants (single and multi-wire) and changes in welding procedure specifications, including joint preparation. Key components of this work relate to the reliable measurement of weld metal strength variation through-thickness and as a function of position around the circumference of a given girth weld.

Jan 1, 2005

By W W. Moorhouse

A survey of recent literature indicates that sulphides occur in the volcanic rocks of the Archean, or in sedimentary rocks intercalated with the volcanic rocks. The thick sedimentary sections are generally poor in sulphides. Thus, the widespread pyrite and pyrrhotite mineralization in the Archean may be largely of volcanic origin. Introduction I N this paper, commercial base-metal deposits will not be considered, as they are dealt with in other papers of the Symposium. Instead, attention will be focused on those sulphides, often associated with graphitic argillites or tuffs, which have appeared in such embarrassing abundance in electromagnetic surveys of Archean areas. The data on which the paper is based are drawn from recent reports of the Ontario Department of Mines, the Quebec Department of Natural Resources and the Geological Survey of Canada. The information available from these sources is unfortunately limited, because sulphides commonly occur in sheared rocks, such as black argillites and tuffs, which rarely form conspicuous outcrops, and may not be exposed at all. Thus, in the absence of geophysical information, even detailed mapping may fail to reveal the presence of sulphide-rich rocks.

Jan 1, 1965

By John Steele

The goal of this project is to detect the presence of objects behind haul trucks and to provide an alarm to the driver if such objects are detected. Objects of interest include people, pickups, other equipment, and large rocks. Another goal is to see if the system can identify the existence of a berm and determine the distance from the truck to that berm, so a safe backup distance can be computed and used as a reference. This paper presents results that demonstrate that such a system is feasible and includes results from work at a local quarry. Architecture of the system is provided and the various subsystems are discussed. Details of the algorthims are included and discussion of the issues involved in developing a fieldable system are also included.

May 1, 2003

By J. Girard, V. Aubé, M. Barakate, S. Bellec, M. R. Eddahabi, Y. Chaik, M. Deshaies

"The activated carbon used in the carbon-in-leach (CIL) process to absorb gold is subject to breakage. This carbon breakage can be minimized, but it will always be necessary to deal with fine carbon particles, known as carbon fines. These fines contain a significant amount of gold and mining operations generally struggle with the treatment of this product. Since IAMGOLD’s Essakane mine is located in Burkina Faso, shipping carbon fines out of the country was not considered a viable solution due to the logistical burden and legal procedures in place. A benchmarking study demonstrated the complexity of treating carbon fines on site. IAMGOLD partnered with the host government to find an innovative approach to economically recover the gold locked in these fines. This paper describes the new circuits commissioned in July 2016 built to improve carbon fines collection, incinerate the carbon fines and leach the gold in the ashes produced by incineration. These new circuits successfully demonstrate that it is possible to extract more than 94% of the gold content in the carbon fines. This is profitable for the company as it improves the overall mill recovery rate by 1.0% to 1.5% and significantly decreases gold inventory build-up on site.INTRODUCTION The activated carbon used in the carbon-in-leach (CIL) to absorb gold is subject to breakage. This breakage can occur in the CIL tanks, the stripping circuit, the regeneration process or anywhere throughout the pumping and handling processes of carbon through the circuit. Fine carbon particles are invariably created and, because of their small size, present a large specific surface which favors gold absorption (Hilsher et al., 2014). At the very beginning of operations at Essakane, the carbon fines were recovered by means of a thickener and a filter press, but the circuit was undersized and inefficient. Subsequently, a decantation basin was used to settle the fines before the thickener. The settled fines were shovelled from the basin into bags. All these bags were stored in the backyard of the plant. The average tonnage of carbon fines recovered monthly was 23.5 tons with a gold grade at 1938 g/t."

Jan 1, 2017

By M. W. Bates, A. L. Mular

This paper, based on work carried out at Queen's University, describes the development and use of mathematical models of the parallel cyclone classifiers being used in the Strathcona mill of Falconbridge Nickel Min.es Ltd.

Jan 1, 1971

By M. A. Hararah, T. Neesse, M. G. Farghaly, G. Proellss, P. Kaniut, W. Rubarth

ABSTRACT: This paper presents two new options for hydrocyclone control. Volume split control using a control valve in the overflow is applied for the stabilization of separation results at changing feed conditions. Controlled water injection to the conical part of the cyclone leads to the reduction of fine particles in the underflow. Hydrocyclone monitoring in both cases is performed by optical sensors that indicate the spray angle of the underflow. Applications in mineral processing for desliming, classification in closed-circuit grinding, and dewatering are demonstrated.

Jan 1, 2011

By M. Bryson, S. Broom-Fendley, A. E. Brady, W. Dawes, G. Beer, N. Sehlotho, S. Al-Ali, F. Wall

The Songwe Hill Rare Earth Element (REE) Project in Malawi is a near surface carbonatite-hosted deposit with synchysite and apatite as the key REE bearing minerals. A strong focus has been placed on understanding the REE mineralogy of the Songwe Hill carbonatite as REE mineralogical characterization is a crucial component at all steps, ranging from exploration to production, in the development of REE deposits. Extensive mineralogical work has been completed at Camborne School of Mines (CSM), Natural History Museum (NHM) London, British Geological Survey (BGS), Nottingham, Aberystwyth University, Wales, Mintek, South Africa, and SGS Inc. Canada (SGS). The following analytical techniques were used: scanning electron microscopy (SEM), electron microprobe analysis (EMPA), laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS), and QEMSCAN®. The detailed studies have demonstrated that while synchysite is light-REE enriched as expected, apatite, abundant in all stages of carbonatite emplacement at Songwe, is anomalously enriched in mid- to heavy-REE relative to apatite in other carbonatite deposits. The distribution of REE within synchysite and apatite at Songwe has had important implications for the direction of the metallurgical work with respect to the behaviour of light and heavy REE through the flotation and hydrometallurgical stages of the flow sheet.

Jan 1, 2014

By H. H. Bleakney

THIS paper presents evidence that in 3 1/2% nickel steel, the published temperature for the Ac1 transformation, l,275°F., represents the completion of that transformation, and that its inception occurs approximately 275°F. lower, at about l,000°F. The formation of austenite within this range, especially at the higher temperatures, and its subsequent decomposition to martensite, results in considerable impairment of the properties of the steel. That the solid solution found to occur below l,275°F. is austenite has been questioned, but the evidence herewith presented, while not decisive, appears to be reasonably convincing. INTRODUCTION The February, 1939, issue of Metals Technology contains a very interesting paper by I. N. Zavarine, Associate Professor of Metallurgical Engineering at the Massachusetts Institute of Technology. In that paper, Professor Zavarine presented photomicrographs illustrative of the microstructures produced by heating nickel steels to a temperature slightly below the carbon change point, and holding them at that temperature for various lengths of time. His illustrations show that the structures found after such treatment do not consist merely of ferrite and carbides, but are characterized by the presence of a third phase, which he describes as a' 'sub-critical solid solution'. The occurrence of this third phase in increasing amounts is accompanied by an increase in strength and a loss of ductility and impairment of elastic ratio of the steel. Some years ago, one of the authors encountered the above-mentioned phenomenon in treating large forgings of 3.5% nickel steel. After normalizing and then drawing at l,250°F., very poor mechanical properties were obtained. Investigation of the steel disclosed no inferiority in quality. Eventually, after considerable waste of time and money, a draw temperature of l,150°F. was tried. This treatment resulted in a very great increase in elastic ratio, over 5 per cent increase in percentage elongation, and proportionate improvement in reduction of area.

Jan 1, 1941

By R. Simon, A. Khosravi

"Tensile strength of rock samples is measured by direct and indirect tensile tests in accordance with standard guidelines. Due to the difficulties in performing direct tensile test, the indirect tensile (Brazilian) test is conventionally carried out to obtain the ultimate tensile strength. A limited number of studies have been conducted to investigate the role of sample size (length to diameter ratio = L/D) in the stress distribution of the Brazilian test using numerical and analytical methods. These investigations showed that the tensile stress distribution along the loading diameter is not uniform. They also indicated that the difference between the tensile stress at the middle part and at the sides of the sample with higher L/D ratio is greater than that in the other samples.The objective of this study is to show the effect of tensile stress distribution on the fracture surface created by the Brazilian test from a morphological point of view on the samples with different L/D ratio. Hence, a series of fracture surfaces created using the Brazilian tests on the rock samples with L/D of 0.5, 0.75, 1, 1.25 and 1.5 were investigated.In this study, all fracture surfaces were scanned by a 3D laser profilommeter. A number of roughness profiles parallel and perpendicular to loading axis have been selected from the samples with different L/D ratio and spacing of 1 mm. The results show that the roughness of the profiles perpendicular to the loading axis increases with an increase of L/D ratio, while the roughness of the profiles parallel to the loading axis decreases. Furthermore, some roughness profiles parallel to the loading axis were chosen and divided into three segments. The results revealed that the segment in adjacent to the upper loading platen possesses higher roughness than the other segments."

Jan 1, 2015

Lonmin RoM ball mills are treating two types of feed ore produced by conventional mining and mechanised mining methods. It was reported that reduction in mill throughput was observed when treating the mechanised mining ore. Detailed grinding surveys were conducted for troubleshooting. Ore samples were collected for breakage characterisation using a JKRBT based on different particle density components. XRD analysis was conducted to investigate the association of minerals with density components. The plant surveys and the breakage characterisation tests all suggested that the two mining methods did not significantly affect either the ore breakage properties or the RoM mill performance. Instead, the mill discharge open area exerted a remarkable influence on mill throughput. The RoM ball mill operated at Lonmin K4 Concentrator has been proven to be a versatile mill that performed stably with variations in feed size distribution and feed ore changes by different mining techniques. The reasons are elucidated by the multi-component breakage characterisation and the plant surveys data.

Jan 1, 2012

By D. P. Ziegler

Formulas relating economic optimum busbar cross sectional areas to busbar cost, electric price and financial parameters are reviewed and revised. Application of the formulas is illustrated with discussion of the appropriate choice of parameter values and the sensitivity of the optimum to the parameters. The extension of the single busbar concept to optimization of more complicated arrangements of bus for smelting pots is complicated by the constraint of obtaining a specified current distribution. An example problem illustrates the optimization of a section of a bus network containing a fork, with the imposed limitation of achieving a specified uniformity in the current. In cases where the current in the individual conductors may vary, Kelvin's law does not apply. Further extension of the technique to a full pot set of conductors poses additional problems which are discussed, but whose solution has not yet been accomplished. Aluminium 2006 45th Annual Conference of Metallurgists ofCIM Montreal, Quebec, Canada Edited by

Jan 1, 2006

By N. Musee, N. Kornelius

This study presents a neural network approach to modelling the liberation of gold bearing ores. A complete mineralogical analysis of unmilled and milled ores, including gold deportment and gangue content are used as inputs to a self-organising neural net which generates order preserving topological maps. The arrangement and shapes of these clusters are coupled to unmilled free gold data to predict gold liberation in milled ores (absolute error: 4.2%). Moreover, the self-organising maps were diagnostic of the quality of data used, indicating that the relationship between particle size and gangue material content requires further investigation.

Jan 1, 2005