Search Documents

By Janice Zinck

?Past? Images of Mining ?Historic practices have been poor ?Mining still widely perceived as environmental ?spoiler? ?Public only hears the bad news stories. Lessons Learned from the Past ?Sustainability matters ?Recognition of social and environmental responsibilities ?Recognition of importance of public concerns and perceptions ?Community engagement

May 1, 2009

By L. A. Mells

"A laboratory test program was initiated by the Department of Energy, Mines and Resources as part of the National Uranium Tailings Program to investigate the applicability of a radium selective ion exchange complexer for removing radium from Canadian uranium mining effluents. The test program was carried out by Melis Consulting Engineers Ltd. under contract to the Department of Supply and Services using the Saskatchewan Research Council facilities located in Saskatoon, Saskatchewan.The results of this work showed the ion exchange complexer, Dowex XFS 43230.00, to be efficient in removing radium from contaminated water of uranium mining operations with the ultimate loading capacity of the resin on one type of water treated being determined as approximately 1,600 Bq/cm3 of new resin. Although this resin has potential application for treatment of effluent streams in uranium operations it has been identified that the resin efficiency and capacity is directly related to the chemistry of the water being treated and site-specific testwork is required in order to establish reliable design data for full-scale operations.IntroductionThe possible applicability of a radium-selective ion exchange complexer for removing radium from Canadian uranium mining effluents had been identified and discussed as a possible alternative to present radium removal methods during a review of disposal technology options for the National Uranium Tailings Program of the Department of Energy, Mines and Resources(1). Work by other workers(2.3) had shown the complexer to be very efficient in removing radium from contaminated water. Also, plant trials on contaminated minewater at the Mt. Taylor uranium mine in New Mexico is reported to have shown the resin complexer to be efficient under plant operating conditions.As a result, a laboratory test program was initiated by the Department of Energy, Mines and Resources as part of the National Uranium Tailings Program to investigate the suitability of this resin for Canadian uranium mining effluents. The test program was carried out by Melis Consulting Engineers Ltd. (MCEL) under contract to the Department of Supply and Services using the Saskatchewan Research Council (SRC) facilities located in Saskatoon, Saskatchewan."

Jan 1, 1985

By L. Mohammadi

Outline ?Background on the accident at the Sullivan Mine No.1 Waste Dump ?Holistic approach to understand the reason for accidents (Atmospheric) ?Specific hazards at reclamation sites ?Regular atmospheric risk assessment at reclamation sites ?Fuzzy risk assessment ?Managing risk at legacy sites

May 1, 2010

By S. Dessureault, M. Yildirim

More mining companies are now investing in IT, including updating one of the traditional IT process control tools used in the mining industry: real time in-pit truck allocation control and monitoring systems, or fleet management systems (FMS). These systems have been used to maximize the overall mine production by improving equipment utilization and reducing production costs. Most modern operations monitor the in-pit operations using GPS and wireless communications to produce data. Improvements in bandwidth, sensors, and computing power are causing modern systems to become more complex and generate more data. However, human analysis by simple regression or table generation in spreadsheets of the data is becoming impossible. Data mining solves this data management problem. Data mining finds patterns and relationships in very large data sets. This paper describes the application of modern data mining techniques on truck dispatching systems in a real open pit hard-rock copper mine. The analyses conducted included determining how the trucks performed under particular conditions and allocation systems. The long-term benefits of this work are to identify strengths and improvement opportunities in truck assignment systems and establish the skill sets and IT infrastructure needed in undertaking more complex datadriven technology such as a truck dispatcher trainer.

Jan 1, 2007

By Rocky (Yaokun) Wu

Rock burst is one of the biggest challenges to ground control in the mining industry. With increasing mining depth and mining scale, there are more and more industry requirements on yielding rock support. Since 2008, Jennmar has been conducting large scale research and development works to develop a technically reliable and cost effective yielding rock bolt. This paper introduces a new yielding rock support - Yield-Lok bolt. The bolt is characterized by the designed yielding ability to produce 150 ~ 250 mm of deflection at 8 ~ 10 metric tons (Mt) loads for every 16.4kJ energy input. Its performance characteristics are consistent through multiple and varying amplitude of impacts. In this paper, the design criteria of the bolt and the principle of performance are described, the dynamic testing results are discussed; and the features and application of the bolt are presented.

Oct 1, 2010

By C. J. Newman, D. J. Kemp, R. M. Sweetin

"The smelter is described by area; feed preparation, continuous furnace line, gas handling and auxiliary systems, blister refining, Hazelett casting of thin anodes, and scrap remelting. Early smelter campaign data is presented and compared to design. Some modifications to the basic design of the furnaces and gas trains are indicated, with their respective impacts on improving smelter performance.Plant compactness, the use of jumbo tanks, and a highly automated electrode handling system are featured in the refinery description, with brief coverage of the liberator and slimes leaching sections. Early experience in refining thin regular Hazelett anodes, and submersible pump recovery of raw slimes are relayed, together with automatic stripping from titanium blanks.Refinery tonnages and operating parameters are given showing the relatively trouble-free attainment of refinery design performance.IntroductionPrevious papers and articles ( 1), (2) ,(3 ) have described the metallurgical facilities serving the copper-zinc-silver Kidd Creek orebody located near Timmins, Ontario. For convenience a brief review of their mid-1983 operating status is presented.The concentrator, originally designed for 9,000 short tons, was commissioned in late 1966. It can now comfortably process over 13,000 metric tonnes per day largely as a result of the addition of a fourth circuit in 1978."

Jan 1, 1984

By William W. Shilts

"In carrying out a geotechnical survey of a proposed gas pipeline route from the Arctic Islands south to Longlac, Ontario, the Polar Gas Consortium contracted the drilling of several hundred 2- to 2D-m-deep boreholes in drift and bedrock. Samples from these holes were made available to the Geological Survey of Canada, where they were subjected to stratigraphic and trace-element geochemical analyses. The geochemical characteristics of the clay and sand-sized heavy mineral fractions of till samples from these boreholes have been summarized in a series of geochemical profiles.From the proposed pipeline terminus at Longlac northward to the vicinity of God's River in Manitoba, tills contain significant amounts of Paleozoic carbonate rocks and Proterozoic sedimentary rocks derived from the Hudson Bay basin and lowlands. Within this section, two sites were enriched in base metals, indicating the possibility of local mineralization of possible economic interest.From God's River northward to Seal River, Manitoba, no evidence of local mineralization was noted. The heavy mineral fractions of the tills are universally enriched in Mn-rich siderite thought to originate on or in the Paleozoic section of the Hudson Bay lowlands.From Seal River northward to Thelon River, near Baker Lake, tills contain only components originating west of the Hudson Bay sedimentary basin. Near the Keewatin-Manitoba border, all till is enriched in uranium, which probably originates in the ""young"" porphyritic granites underlying much of the region, and produces a distinctive airborne radiometric anomaly.At the Thelon River, multiple till sections are variously enriched in Cr, Ni, U, Cu and Mo in the vicinity of a distinctive aeromagnetic anomaly.From Thelon River northward, several coincident zones of chromium and uranium enrichment are found where the line of boreholes crosses east-west-striking belts of volcanic, ultramafic and sedimentary rocks of the Prince Albert Group.The results of this study indicate that till tends to have characteristic element associations or concentrations over each of several broad regions along the pipeline route. These are related both to large-scale bedrock associations and to largescale effects of glacial dispersal. In addition, the samples, collected more or less at random with respect to local bedrock geology, have intersected several small-scale geochemical anomalies that appear to be related to zones of mineralization of possible economic interest."

Jan 1, 1980

By P. R. Cook

Thunder Bay Terminals' plant, now in operation, cost about 70 million dollars and was completed on time and under budget. The paper is the project manager's account of this accomplishment. From site selection through feasibility, engineering and construction to realization, he emphasizes the necessary philosophies for the control of time and money. The computer as a tool is discussed, as well as techniques for procurement.

Jan 1, 1979

By J. L. Jambor, E. J. Reardon, E. C. Appleyard, J. A. Cherry

Since the 1957 initiation of deposition of mill tailings at the Heath Steele mine, New Brunswick, periodic detailed studies of the tailings geochemistry and mineralogy have been conducted, thereby providing a unique opportunity to examine the geochemical evolution of a sulfide rich mine>tailings impoundment. When deposited, the tailings contained about 85 wt% sulfide minerals, 1 wt% to 3 wt% carbonate minerals, and 12 wt% to 14 wt% alumino silicate minerals. Mineralogical examination of samples of the tailings from deep in the impoundment indicates that little oxidation occurred prior to tailings deposition. The mill process-water deposited with the tailings was neutral to slightly basic and contained low concentrations of Cu, Pb, Zn and As. Sampling of the tailings five years after deposition indicated that sulfide-oxidation reactions, occurring near the tailings surface, had decreased the tailings-water pH and increased the concentrations of Fe, S042-, Cu, Zn and Pb (up to 10 000 mglL, 25 000 mg/L, 2.5 mg/L, 200 mg/L, and 4.5 mg/L, respectively). In 1975, ten years after decommissioning, the tailings could be divided into three zones: an upper oxidation zone in which sulfide oxidation is actively occurring, a hardpan layer, 15 cm to 20 cm thick, composed of tailings cemented by secondary Fe minerals, and an underlying reduction zone in which the tailings are relatively tin oxidized (Boorman and Watson, 1976). Chemical analyses indicated the presence of low-pH waters containing very high concentrations of SOi-, Fe, and other metals (up to 63 600 mg/L SO42-, 28 600 mg/L Fe, 10 mg/L Pb, 600 mg/L Cu and 4000 mg/L Zn), suggesting that there was a period of intense sulfide oxidation between five and ten years after tailings deposition. More recent sampling, conducted some 20 years after the end of tailings deposition, indicates that relatively little change has occurred in the last ten years, thereby suggesting that the hardpan layer has provided an impediment to the downward movement of dissolved constituents. Analyses of the tailings solids show increased accumulations of many metals at or near the depth of the hardpan layer. Evaluations of the long-term evolution of the tailings can be enhanced by comparison of descriptions of the tailings with descriptions of the gossan that overlay the massivesulfide orebody prior to mining. At Heath Steele, this comparison suggests that many of the mechanisms controlling the distribution of metals in the tailings will probably persist over geologic time.

Jan 1, 1992

By G. W. Neumann

"In order to avoid pollution of water in Flemming Brook and Little River, which drain the area in which the Brunswick No. 12 Mine and Concentrator are located, the company has gone to considerable expense in preparing tailings storage and effluent setting ponds. The attached drawing gives a plan of the six settling ponds together with elevations of the dikes and the effluent weirs.All original dikes for the six ponds were constructed from humus-free clay and rock material, which was obtained, preferentially, by excavating from within the dike area. Run-off water, precipitated on the outside slopes of the dams will drain off without contacting the tailing material. A ditch was made north of the dam site to deflect surface run-off to the east into a branch of Flemming Brook.A secondary dike, made from tailings, has recently been erected on No. 1 and No. 2 tailings pond inside and above the earth-filled dike which serves as a roadway. Run-off from the tailings dikes will be retained inside the ponds by ditching between the roadway and tailings dike into ponds 4 and 6."

Jan 1, 1969

By J. Carr

This paper discusses: (1) the need for Western Canadian coal in eastern Ontario Hydro plants; (2) design parameters-unit trains, year- 'round receiving from trains, and shipping (Great Lakes season); (3) equipment chosen-dumper-indexer, outhaul conveyor, yard belt, stacker, reclaimer, surge-bin feeders, shiploader, docking system and dust control; (4) foundation and soil conditions-dumper house, yard belt, surge bin and dock-piling-runway; (5) winter conditions- thaw shed, feeder, lump breaker, beltings (oil), and dust control and disposal; and (6) operations to date.

Jan 1, 1979

By K. Blower

"Since there was no representative from Wesfrob Mines Limited, the information on their infra-red concentrate drying operation, which had been prepared by Mr. K. Blower, was presented by Mr, Dorland. Mr. Blower, in submitting the information, emphasized that their objectives in this operation were (a) to guarantee less than 90%, of flow-moisture in their copper concentrates and thus satisfy marine shipping regulation• and (b) to minimize capital costs, The infra-red dryers have satisfied these objectives.To control final moisture in the copper concentrate, current practice is to preheat the filter cake with steam in the disc filter hood and then conveyor-0r7 the concentrate with infra-red calrod heaters. The application of steam aids the system as follows:1) Improves vacuum pump efficiency.2) Lowers viscosity of filtrate (increased temperature},3) Preheats the cake prior to radiant heating. (150°F)The hot cake discharging from the filter ranges from 10.6 to 10.9% moisture. After radiant heating the moisture level is reduced to 8.5% - 9.7% depending on production rate. Further moisture loss occurs during conveying and transferring to the stockpile for a final shipment moisture ranging from 8.1% to 9.5%. Production rate is frail J to 5 dry short tons per hour.1) #23 Conveyor 18"" flat belt covered from filter discharge to transfer point with 7 heaters end-to-end. Drive - Reeves Vari-Speed, 31:4 ratio, type 332-10-18, class ""D"", driving through a 24:1 ratio Dodge reducer. Speed of Conveyor - 3,9 feet per minute to 19.6 feet per minute. (Speed has been established and is not changed as a rule from the present level of a1:out 15.)2) #23 Conveyor 24"" wide, 20° troughed belt covered with 21 heaters, end-to-end from loading point, Speed - Constant at 54,2 feet per minute."

Jan 1, 1972

By Garston Blackwell

Abstract - During geostatistical estimation of block grades, the kriging process produces a measure of error, the kriging variance or the kriging standard deviation. Estimation of the block error depends on the semi-variogram model for a deposit, which reflects fundamental characteristics of a deposit such as (1) nugget effect, (2) range of influence of grades, (3) different local spreads of data as a function of average grade (proportional effect), (4) nested structures, and (5) underlying anisotropies in the data; this model may be affected by sampling or assaying limitations, however. Because the kriging error incorporates so many features of both the deposit and data to be used for estimation, it may offer a substantial improvement on block classification over traditional procedures such as data density. Practice indicates that the relative kriging standard deviation (RKSD) is particularly useful for block classification in measured, indicated and inferred categories. Plots of RKSD in plan and section also can be used to demonstrate where extra drilling and sampling would be most advantageous for upgrading the class of some blocks. Moreover, the use of grade and RKSD filters can show where material near cut-off grade is poorly defined, indicating sampling target areas to improve block classification in the vicinity of the ore-waste boundary.

Jan 1, 1998

By J .. R. Brown, G. Deschenes

X-ray Photoelectron Spectroscopy (XPS), X-ray Diffraction (XRD) and Electron Probe Micro-Analysis (EPMA) were used to characterize chemically the gold complex adsorbed on activatedcarbon from a solution containing 102mglL Au and 0.5 giL thiourea. This paper also considers the gold chloride and the gold cyanide systems. The results indicate gold is adsorbed on activated carbon from the thiourea solution as the gold (I) thiourea complex, i.e. Au [CS (NH) 2];' Other gold species such as metallic gold were not detected on the carbon support. These results also suggest the elution of the gold (I) thiourea complex can be performed with high recovery.

Jan 1, 1993

By R. D. Brown

Higher metal prices have resulted not only in increased exploration and production, but also increased activity in the purchase of mining properties and mines. This article discusses some of the basic income tax considerations to be taken into account on the disposal of an interest in a mining claim or an active mining operation. It notes the importance ofan appropriate allocation of the purchase price amongst the various categories of assets, and discusses the tax implications to both vendor and purchaser of the transfer of the comm on types ofassets involved in mining operations. In the space available, the article can only outline the basic tax considerations, and point to areas where both vendor and purchaser need to be o

Jan 1, 1980

By J. H. Archibald

"In mines employing cut-and-fill stoping (sand fill), ore passes are built as mining progresses upward. These ore pass raises are generally made from timber and form a vertical ""chimney"", like a very tall log cabin. Traditionally the chimney, or raise, is square in shape and is constructed from square timbers with stepped ends as shown in Figure I. The timbered raise is thus surrounded by sandfill on its outside, leaving the centre open for passing ore down through it. Each layer consists of four timbers and rests flush on the layer below. The corners are frequently pinned or spiked.Under certain conditions in sandfilled stopes large horizontal loads may be transmined to the raise cribbing timbers, or the ""chimney's"" walls. In deep mines, where rock bursts are a problem, it can be shown that one of the conditions for rockbursts to occur is that the burst zone be stiffer and weaker than the surrounding rock(l). This allows a strain energy build-Up in the rock surrounding the burst zone, and the rate of release of this strain energy is known to be related directly to the over-all strength and stiffness of the rock in the burst zone. In stopes that are sandfilled, attempts are, therefore, usually made to increase the strength of the sandfill by the addition of large-sized waste rock and Portland cement. These measures usually achieve the desired strength of the sandfill and, consequently, the severity and frequency of rockbursts can be reduced.Problems may arise when the now chunky sandfill transmits high loads to the raise cribbing along with relatively large move- merits. This leads to heavily stressed and strained cribbing timbers the Coeur d'Alene district in Idaho, raise cribbing failures are common. A typical mode of cribbing failure is shown in Figure 2. One learns in statics that a structure shaped like the crib in Figure I is inherently unstable , at least from a structural standpoint. The crib has pivoted, in Figure 2, into a rhombi c shape and supports very little load. Soon the four-foot square raise cribbing made from 5 in. by 5 in. timbers will no longer pass ore."

Jan 1, 1991

By J. Bruce See

INTRODUCTION This symposium at Cu 2019 has been organised to honour and celebrate the career and achievements of Dr Phillip John Mackey, an internationally recognised expert in the production of non-ferrous metals, especially copper and nickel smelting and refining. Phillip was born in Epping, a suburb of Sydney, New South Wales, Australia on 19 April 1941 and is one of 4 children of Gilbert and Philomena (nee Bartlett) Mackey. After completing Primary School in Epping, he attended Marist Brothers High School in Eastwood, Sydney and graduated in 1957 as the Dux of the School. Phillip’s father, being on the staff of the Sydney Technical College, in Ultimo, Sydney had the opportunity in the early 1950s to meet the late Professor Sir Rupert Myers, Foundation Professor of the School of Metallurgy at the New South Wales University of Technology (later called the University of New South Wales or UNSW). Gilbert Mackey was impressed by the new young Professor of Metallurgy and encouraged his son to study metallurgy - at the time an expanding industry in post-war Australia. EDUCATION AT THE UNIVERSITY OF NEW SOUTH WALES Phillip commenced at UNSW in 1958, graduating with honours in 1963. His undergraduate education and training included a few years of part-time study while working at British Motor Corporation on sheet metal forming of car bodies. At University Phillip developed his talent for teamwork. He was a contributing writer to the University newspaper, Secretary of the UNSW Students’ Union and was active in the UNSW Metallurgical Society and co-editor in 1963 of “Metallurgical Review,” the annual journal of the UNSW Metallurgical Society. His diverse interests and curiosity about the world around him were likely nourished while at University. Upon completing his Bachelor’s degree, Phillip was awarded a Commonwealth of Australia Postgraduate Research Scholarship. He began his PhD in 1964 on the thesis topic “Studies in Heat Transfer between Dispersed Liquid Metals and Gaseous Atmospheres” working under the supervision of then Associate Professor Noel Warner, an outstanding Professor at the University. Professor Warner is now an Emeritus Professor at the University of Birmingham and is internationally respected for his pioneering theoretical and practical work on established and innovative smelting processes.

Jan 1, 2019

By Margaret Armstrong, Chris Roth

Abstract -Estimating ore reserves for vein type deposits is a two-stage procedure: first, calculate the geometry of the vein system, and second, estimate the grades within this system. The grade estimation can only be consistently performed if the vein geometry - its size, shape and orientation - has been correctly characterized. Getting the size and shape of the different veins right means that the ore tonnages will not be artificially inflated, e.g., by falsely classifying host rock as veins. Similarly, correctly estimating their orientation and location helps mine management decide on the appropriate mining technique, selective or not. When applying geostatistics to estimate the vein geometry all available information needs to be used and not just the standard lithologic indicator of being or not being in a vein.

Jan 1, 1998

By H. Y. Sun, Q. Y. Tan, X. P. Niu, L. Li, Y. Jia, R. M. Ruan

During bioleaching processes of sulfide minerals, the sulfide minerals act as the natural habitats for acidophiles, of which, most are autotrophic iron and sulfur oxidizing microbes. These microbes acquire energy by oxidation of sulfide minerals, and play crucial role in bioleaching processes. In the industrial bioleaching heaps, microbial community and their activity are highly related to engineering configurations, while the optimized industrial operation can help to fast dissolution of aim minerals and acid/iron balance under optimized microbial condition. Microbial community succession and activity formation, the function of microbes to mineral dissolution, the mechanisms to promotion and inhibition of sulfide minerals oxidation, and the industrial instances for microbial community regulation were reviewed. For these instances, promoted microbial activity helped to fast pyrite oxidation for sulfuric acid generation, which realized zero sulfur acid addition to the irrigation solution in the initiation of a bioleaching heaps. High microbial activity by optimized operation parameters improved Cu leaching efficiency during the heap bioleaching process. And also by inhibition of microbial activity, especially the iron oxidizing microbes, the excessive pyrite oxidation can be inhibited, which helped to the acid/iron balance during heap bioleaching. INTRODUCTION Around the world, high grade copper ore are exploited, while barely new high-grade deposits are succeeded, the copper grade of ore deposit is constantly decreasing. The increasing copper demands worldwide requests to process these low-grade ore deposits. Processing of low-grade ores are not economical by usual extraction processes. Heap leaching is a cheaper process for recovery of low-grade ores, and has been applied to extract valuable metals from sulfide minerals worldwide, such as copper, gold, uranium and nickel (Gericke et al., 2009). Heap leaching process has greatly decreased the economic grade and expanded the recoverable ore reserve worldwide (Brierley, 2008). It is usually carried out in the open environments, and could process huge amount of ore (usually in millions of tonnes in one reactor) in the heap reactor (Gericke et al., 2009). For copper sulfide, especially the secondary copper sulfides, heap (dump) bioleaching is successfully applied. Heap bioleaching process is cost saving, and sometimes can be achieved without adding chemical into heaps, by microbial fixing of the atmospheric N2 and CO2, and generating oxidant Fe3+ and sulfuric acid in heaps from oxidation of sulfide minerals. Also heap bioleaching is environment friendly by cycling use of the leaching solution, and without exhaust emission.

Jan 1, 2019

By John D. Smith, Robert J. Mitchell

"There is a world-wide trend toward underground bulk mining methods employing hydraulically placed backfill. This trend is recent and therefore there is little in the literature to assist an operator in the design of backfill properties, the design of drainage facilities, the calculation of the operating forces on a bulkhead, and the control procedures considered necessary before, during and after pouring. This paper presents recommended procedures that are based on over to years of experience in the various aspects of backfilling large openings. Free-draining timber or concrete block bulkheads are shown to be a viable alternative to massive reinforced concrete bulkheads for the containment of backfill pours. Hydrostatic pressures cannot develop in backfills provided adquate drainage facilities are installed.IntroductionThe increasingly adverse relationship between mining costs and mineral values has led mining companies to develop more productive, lower-cost, bulk mining methods. This has led to the increasing use of large, more or less continuous, hydraulically placed backfill pours to enable the recovery of a higher proportion of pillar ore. The success of any bulk mining method depends on the degree of stability maintained during the stoping operations with reference to the mining rate, the performance of the backfill with respect to the per cent extraction of pillar ore, and the control of the mine structure with respect to safety and productivity. One such method has been previously described(I) where a steeply dipping orebody is being mined with a sub-level method that employs large, hydraulically placed tailings pours for delayed pillar recovery. The paper describes the rock mechanics analysis undertaken to establish the stope and pillar geometry and the approach taken to establish backfill strength requirements to prevent dilution during pillar recovery. Production with this method started in 1970 and because few, if any, large bulk pours had previously been used in- this way (judging by the lack of information in the literature), design data and criteria were needed for several aspects of the work. Methods to establish backfill quantities and pertinent ""in-place"" fill properties are described in 2, 3 and 4 in the list of references. Results of field measurements taken to establish fill pressures for bulkhead design purposes are described in 5 and 6. Laboratory large-scale model tests undertaken to confirm a fill strength design equation, which takes into account fill arching, have recently been completed. A paper describing these tests and the results will be forthcoming in the near future."

Jan 1, 1982