Search Documents

By H. Wotruba, K. Neubert

Dual-energy X-ray transmission (DE-XRT) imaging is known from safety luggage inspections at airports. The use of DE-XRT technology for sorting applications in the primary raw materials industry has been the subject of numerous investigations. Beside other metal ores, X-ray transmission sorting is already used for the preconcentration of tungsten ore, gold ore and coal. The applicability of DE-XRT sorting is limited to ore types where differences in metal concentrations are measurable, based on an interpretation of X-ray images. Metal contents in particles occur in large varieties in terms of concentration, grain sizes, spatial distribution and mineralogy and therefore influence the X-ray absorption. As a result, each ore has to be tested individually for its suitability for DE-XRT sorting. The objective of current research at the Department of Mineral Processing (AMR) at RWTH Aachen University is to assess parameters influencing the detectability of rare earth oxides. Two approaches were followed: (1) Practical test work, based on artificial ore samples of defined compositions and (2) Computer-based simulation of absorption features of identical particle compositions. In total, more than 300 artificial samples of various compositions and metal grades were produced and X-ray images from DE-XRT sorting were analyzed. Results from the DE-XRT sensor were put into correlation with metal grades and particle sizes, to analyze influences and limits on the detectability of rare earth oxides. In addition, a new approach was tested in which the X-ray absorption of particles of various compositions was determined based on a Monte Carlo (MCNP) simulation. During the simulation, similar compositions, as used for the artificial samples, were tested and the X-ray absorption behavior during DE-XRT sorting was determined. A comparison of results from both approaches is used to assess the applicability of the MCNP-simulation for the prediction of the X-ray attenuation behavior during DE-XRT sorting.

Jan 1, 2016

The recovery of fine hydrophilic gangue in flotation is related to the recovery of water. Water is carried by bubbles as a film and wake into the froth. The amount carried (entrained) depends on bubble size, gas rate and the subject of this paper, frother type. To isolate the effect of frother type from that of bubble size and gas rate, gas holdup is used as the correlating variable. Measurements were made using a bubble column (no solids) operated continuously with the overflow recycled. Continuous operation meant some foam depth was required to ensure only entrained water is recovered. Using an automatically controlled 7cm foam depth the overflow rate of water is used as a measure of 'water carrying rate'. It is shown that the common frothers can be grouped into four families based on the water carrying rate-gas holdup relationship.

Jan 1, 2006

By M. du Plessis, G. More O’Ferrall, A. Hartzenberg

"Lonmin Platinum has experienced several cases of large-scale hangingwall instabilities during the extraction of the Upper Group 2 Chromitite Layer (UG2) at a number of the Marikana operations along the Western Limb of the Bushveld Complex. These instabilities were all attributed to the presence and interaction of prominent geological features and highlighted that assumptions made in the design of the stable pillars and stable span were potentially overly simplistic in these areas. Investigations into the various case studies over the past ten years have resulted in the identification and classification of the rock mass characteristics of the geological structures causing the instabilities.In order to get a better understanding of these instabilities, it is important to understand the structural geology in general, and the sequence of events that led to the formation of the Bushveld Complex in particular. The tectonics involved in the formation of the various layers around the economic mineralized layers has been investigated, and the influence of these tectonic events on the stability of the UG2 stopes hypothesized.Following this investigation, the behaviour of the various layers in the hangingwall of the UG2 is better understood. This paper presents a description of the ground conditions being experienced in the underground stoping environment, the possible source of the associated structures and the resultant behavioural mechanism of these structures causing the rock mass instabilities."

Jan 1, 2015

By Frank Ebbutt

Introduction The property of the Britannia Mining and Smelting Company, Limited, is situated on the east side of Howe sound, about six miles from its head. It is roughly thirty miles by water from Vancouver, one of the important ports of the Pacific and the industrial and financial centre of British Columbia. Howe sound is navigable for ocean-going vessels and Britannia Beach is a daily port of call for the commodious boats of the Union Steam-ship Company, sailing from Vancouver. Few mines are so ideally situated or have so many or varied natural advantages. Copper was first found on Britannia mountain in 1888, by Forbes, but it was not until 1898 that five claims were staked here by Oliver Furry, a trapper. It is from these claims that the major production during the past thirty years has come. In 1900 the Britannia Copper Syndicate was formed and development of the property was commenced. In 1903 the late Grant B. Schley obtained control, and through his efforts the Britannia Mining and Smelting Company was organized in 1908 as a subsidiary of the Howe Sound Company. Since that time, a persistent and progressive policy has been followed, which has resulted in a prolonged and profitable operation. The country in the immediate vicinity of the mine is marked by strong relief, with mountains rising abruptly from tide-water to elevations of 5,000 feet and more. Two broad transverse valleys deeply dissect the area. These are the valleys of Britannia creek and Furry creek. The region has under-gone prolonged and relatively recent glaciation. Over much of the surface there is deep overburden and dense vegetation. The geology of the mine and vicinity has been described in reports by S. J. Schofield (1), H. T. James (2), J. G. Barry, and others (3). The present writer is in accord with much of this literature on Britannia, but during recent years, extended observations made underground have shown that the 'quartz porphyry', or 'mine porphyry', of several of the earlier writers is not the host rock to the commercial mineralization; and he contends that the mineralization occurs in highly altered phases of a complex series of ruffs, flows, and pyroclastics and their autoclastic metamorphosed products.

Jan 1, 1935

By J. R. del Castillo, J. Ruiz, N. Kuyucak, J. Chavez

Environmental Impact Assessment (EIA) and Feasibility Studies (FS) were carried out to evaluate the potential use of treated acid mine drainage (AMD) occurring at the Kingsmill Tunnel in the Central Andes of Peru. The 11-km long tunnel drains the underground works of the Morococha Mining District and discharges about 1.25 m3/sec of AMD directly into the Yauli River, which is located within the Amazon Basin. The communities living downstream cannot use the Yauli River water due to its low pH and elevated concentrations of metals (e.g., Cu, Zn, Fe, Mn, As, Cd) and sulfate. Studies carried out for this project included technical feasibility, EIA, economic viability and social impact assessment phases. During the "Technical Feasibility" phase, the treated AMD was produced by simulating a high density sludge (HDS) lime neutralization/precipitation process and was evaluated for various potential uses. Mining companies located in Morococha, in particular Centromin Peru S.A., and the Water Works Company of the City of Lima (Sedapal) collaborated with Golder Associates during the studies. The Canadian International Development Agency (CIDA) provided the financial assistance. The results of the physical, chemical, biological and toxicological analyses demonstrated that the treated AMD could be used for supplementing the drinking water supply of Lima and for agricultural (e.g., irrigation and livestock) and recreational purposes. Process design and scale-up parameters were also determined for the implementation of the full-scale treatment facility to the site. The use of the treated AMD as a drinking water supplement would be economically feasible.

Jan 1, 2004

By D. Mraz

"In certain instances, rocks around underground excavations behave as a plastic mass. This paper offers several solutions to predicting the mode of plastic flow around cavities and designing mining pillars where plastic conditions exist.IntroductionWhen stresses around underground cavities exceed yield limits of the host rock, the material often behaves as a plastic mass. The best example of this phenomenon is the behaviour of salt rocks in deep salt and potash deposits (more than 500 m deep).However, many other soft rocks exhibit similar properties. For example, Jeremic(1) described certain types of coal yielding plastically under high pressure. Alder suggested that granulated rock behaves plastically.The object of this paper is to propose a de sign procedure for mining pillars exhibiting plastic flow due to the combination of rock properties and in-situ stresses.Prandtl(3) mathematically defined a concept of a generalized, perfectly plastic substance, not possessing the property of strain hardening (Fig. I). He had in mind, a solid with a quasi quasi-isotropic , polycrystalline structure having a well defined yield point, and he postulated that its material elements start and continue to deform plastically when the maximum shearing stress ""'MAX"" reaches a sharp limit, dependent on the mean value of the sum of the major and minor principal stresses:"

Jan 1, 1984

By Sejong Kim, Younghoon Moon, Youngseon Lee, Eunyoo Yoon, Yonghyun Song

"Mg alloy has a high specific strength, however, their thickness reduction was limited on most parts because of their poor stiffness. Since the modulus of rigidity is an intrinsic property, improvement of modulus of rigidity to the enhancement of stiffness is impossible. Therefore, the modification of shape and structure is available method to enhance the stiffness of real part fabricated by Mg alloy sheet. There are many thin walled parts which are located in outer section of electromagnetic system.Poor stiffness is often shown on wide surface area part with steel sheet, which has also high modulus of rigidity. In these cases, various groove patterns are used to increase the stiffness of part. However, some different methods have to be used when general groove pattern can’t be used. So, we would like to propose some new method to high stiffness on thin walled precision forging of Al or Mg alloys.An effect of proposed method on stiffness enhancement can be confirmed by fabrication of prototypes as well as structure and forming analysis based on FEM."

Jan 1, 2015

By C. McLachlan, J. R. Donald

"Positioned at the forefront of the seafloor minerals industry, DeepGreen Resources is on track to becoming a leading producer of base and strategic metals obtained from vast high-grade seafloor polymetallic nodule deposits. DeepGreen believes the seafloor minerals industry is an opportunity for developing a more environmentally and societally attractive way to produce cleaner base and strategic metals. Polymetallic nodules contain nickel, manganese, copper, cobalt and other base and strategic metals. Polymetallic nodules represent an exceptional multi-metal-bearing resource, and no current metallurgical operation or flowsheet exists that can recover the primary metallic values while managing the distinct mineralogy. DeepGreen Resources is developing a new process to maximize the business outcomes consistent with the highest environmental standards, including targeting a near zero waste facility. The present paper discusses the history, context and driving forces of polymetallic nodule project development. An overview of DeepGreen?s Nauru Ocean Resources Inc. (NORI) project is presented along with a literature review of polymetallic nodule processing and the on-shore project development scope and plan at DeepGreen Resources is outlined.INTRODUCTION AND CONTEXT Polymetallic Nodules in the Clarion-Clipperton Zone Containing nickel, cobalt, copper and manganese, polymetallic nodules occur in most oceans of the world. The nodules lie on the seafloor sediment. The largest deposit in terms of nodule abundance and metal concentration occurs in the Clarion-Clipperton Zone (CCZ) on vast abyssal plains at a depth of 4,000 to 6,000 metres. The CCZ is located almost entirely in international waters as presented in Figure 1. It has been estimated that the CCZ contains (International Seabed Authority, 2010): •,>21 billion tonnes of nodules; •,>270 million tonnes of nickel; •,>6 billion tonnes of manganese; •,>234 million tonnes of copper; •,>46 million tonnes of cobalt. There are several active hypotheses for the mechanism of formation of the nodules including precipitation, hydrothermal decomposition of basaltic debris, and involvement of microorganisms. Nodules require a nucleus to start forming, which could be a piece of pumice, a shark tooth, old nodule piece, basalt debris or even microfossils like radiolaria and foraminifera. Nodules form concentrically with layers of iron and manganese hydroxides around a core. Although composed mainly of Mn, Fe, silicates and hydroxides, it is the significant content of Ni, Cu, Co, Zn and Rare Earth Elements (REE) that is generating the economic interest in harvesting these deposits. Nodules vary in size from micro-nodules to about 20 cm, the common size being two to eight centimeters. A typical polymetallic nodule and polished cross-section is presented in Figure 2."

Jan 1, 2017

By C. J. Mwenifumbo

Preservation of groundwater quality is a major environmental concern. The disposal of hazardous material from urban waste dumps, milling wastes in tailings ponds, and industrial wastes in injection wells may contaminate potential sources of potable groundwater. The containment or migration of contaminants in the subsurface depends on bedrock characteristics and type of overlying sediments. Fractured bedrock and permeable sediments that may provide pathways for the transport of potentially harmful contaminants should be avoided when selecting a disposal site. The role of borehole geophysics in hazardous waste-site investigations is reviewed in three categories: (I) site selection; (2) determination of the extent of contamination at existing sites; and (3) long-term monitoring of migration of contaminants. In the first category, borehole geophysical techniques developed for lithology and fracture identification, and for porosity determination, provide some of the necessary information for understanding the subsurface hydrogeology. Lithological information can be obtained from gamma-ray, electrical resistivity, induction, magnetic susceptibility, and sometimes induced polarization logs; fracture detection and characterization can be accomplished with the use of caliper, density, resistivity, temperature, and acoustic televiewer logs. Estimates of porosity are derived primarily from neutron-neutron, resistivity, density, and soniclogs. Borehole geophysical techniques used in water quality determinations include self-potential, fluid resistivity, Eh (redox potentials) and pH measurements, and these can be used to map the extent of contamination at an existing waste site. Cross borehole and borehole-to-surface electrical methods can also be used in this application. Long-term monitoring of contaminant migration in boreholes can be accomplished with techniques that respond to changes in electrical conductivity, temperature and fluid chemistry caused by the presence of contaminants.

Jan 1, 1993

By J. H. Ambrose

Introduction The copper smelter of the Hudson Bay Mining and Smelting Company, Limited was constructed to handle the concentrates produced by the concentrator, the residues from the zinc plant, concentrates from Sherritt-Gordon Mines, Limited, and other custom material that might be available. Construction work was started in 1929 and the first concentrates were smelted in November, 1930. From that time until June, 1931, the operations were more or less of an experimental or tuning-up nature. In designing the smelter, it was believed the following tonnages would be available for smelting per day: Copper Tons Content H. B. M. & S. Co. concentrates 331 14.0 per cent H. B. M. & S. Co. zinc plant residues 77 2.5 per cent Sherritt-Gordon concentrates 200 20.0+ per cent Consideration was given to wet-smelting the charge, but, in order to give greater flexibility to the operation, it was finally decided to roast the concentrates before smelting. Briefly, the smelter equipment consists of three Nichols-Herreshoff roasters, one reverberatory furnace, two Peirce-Smith converters, a Walker casting wheel, and a four-unit Cottrell plant, two units' for the roaster gases and two for the converter gases. A general plan of the smelter is shown in Figure 1. Prior to the commencement of smelter operations, a stockpile of about 9,000 tons of concentrates had been built up by the concentrator and the old pilot-mill. The zinc plant was in operation, but the equipment for drying the residues at the smelter had not been completed. Sherritt-Gordon did not commence their shipments of concentrates until April, 1931. The only flux available was barren sand from a pit ten miles south of Flin Flon, adjacent to the railway. Several small deposits of metal-bearing siliceous ore had been discovered in the district, but none of these were sufficiently large to be considered as a source of smelter flux. At the beginning of March, 1931, the entire stockpile of concentrates had been consumed, and available tonnage for smelting was limited to the daily production of the concentrator.

Jan 1, 1935

By B. Hewitt

Murrin Murrin Operations has not had a successful beginning. Numerous reliability and operability issues many of which are the result of design decisions have been addressed through mechanical and operational changes and the CCD circuit is no exception. The decision to install, the installation and the results of the CCD1 rake-lift mechanism and feedw ell dilution system are discussed in this paper. The installation was justified on improved operational robustness and an increase in the in the underflow density of 1% (per cent w/w). At approximately the same time process modifications in the solution neutralisation circuit were implemented and these changes altered the rheology of the slurry reporting to CCD1. Since the modifications to CCD1 and the solution neutralisation circuit, the CCD circuit has averaged a 2% improvement in the circuit underflow density. The CCD1 modification was completed on time and mechanically has performed well. From a risk point of view, the central rake-lift and Turbodil® dilution system add a degree of freedom and robustness to CCD1 operation that has extended the range of operational confidence. In this respect, the modification has been a success and is complementary to solution neutralisation improvements.

Jan 1, 2004

By Bruce Macdonald

Operational monitoring of slope stability can be achieved by space based InSAR monitoring platforms. Natural and man-made rock slopes are monitored using a novel stack-based InSAR method that exploits both persistent point scatterers (PS) as well as coherent distributed scatterers (DS) such as areas of pavement and sparsely vegetated surfaces. The new method, Homogenous Distributed Scatterer (HDS)-InSAR identifies InSAR targets by using adaptive multilooking of statistically homogenous pixel neighbourhoods combined with thresholding the differential temporal coherence of each target candidate with respect to its surroundings. HDS-InSAR preserves PS and therefore forms a direct generalization to our proven DualScale-PSI method. The density of HDS exceeds that of PS by more than an order of magnitude often providing essentially continuous coverage over urban and industrial landscapes featuring a mix of infrastructure with mostly bare soils or rock surfaces. The improved coverage enables better definition of surface motion and underlying geology, which will lead to superior interpretation of the geophysical mechanisms causing the surface deformation, e.g. through improved integration with 3D deformation modeling. We illustrate the performance of our new HDS-InSAR method compared to DualScale-PSI using displacement results from Vancouver, Canada; Bingham mine, USA; and the Palabora mine, South Africa.

Jun 1, 2012

By T. Boyd, K. McTaggart, J. Qiu

"Hudbay Minerals’ Flin Flon process plant produces a copper concentrate and zinc concentrate from the three ores it processes: 777, Reed and Lalor. Unlike many Cu-Zn ores, the average Zn: Cu ratio in feed is around 2:1, whereas, in many Cu-Zn separation plants the Zn: Cu feed grade is substantially higher than 2:1. The lower Zn: Cu in plant feed is a challenge for limiting Zn recovery to the Cu concentrate. While total recoveries of Cu and Zn at Flin Flon are very good; selectivity is the key challenge and small changes in ore or plant, can result in quite variable Zn recovery to Cu concentrate, and accordingly, Zn recovery to Zn concentrate. Magnetic conditioning has been shown to be selective between the two paramagnetic minerals chalcopyrite and sphalerite. Statistical testing of magnetic conditioning was undertaken at Flin Flon with the objective of increasing Cu recovery to Cu concentrate without increasing the Zn recovery to Cu concentrate - in effect increasing Cu-Zn selectivity. This has been achieved elsewhere with magnetic conditioning with the probable mechanism being an increase in fine chalcopyrite recovery, and a reduction in entrained, ultrafine, non-activated sphalerite to Cu concentrate. The results did indeed show an increase in Cu recovery to Cu concentrate of 0.8% to high confidence, but the decrease in Zn recovery to Cu concentrate was not to high confidence. This is effectively an increase in Cu: Zn selectivity in the Cu circuit – higher Cu recovery with no change in Zn recovery. However, while there was an increase of 1% in Zn recovery to Zn concentrate with magnetic conditioning, the variability in this parameter meant that this increase, though larger in magnitude than the Cu result, was not to high confidence."

Jan 1, 2019

By S. M. Chentouf, M. Jahazi, N. Bombardier, T. Belhadj

The main limiting factor in the commercial expansion of superplastic forming (SPF) of thin sheet aluminum alloys is the extent of cavitation phenomenon that takes place during the processing. The severity of the cavitation process is mainly dependent on the uniformity of deformation (i.e. level of local thinning) during processing. In the present paper, correlations are made between thickness variations in several formed sheets and the characteristics of the cavities observed in the material. The 1.4 mm thick 5083 aluminum alloy sheets were hot pre-formed at around 450°C for 4 min and then air-cooled. Opto-digital and Scanning Electron Microscopy were used to examine the microstructure and analyse the cavities. Also, grain size measurements were carried out for different location in the SPF formed piece. The surface and volume fractions of the cavities were measured with the aid of metallography image processing (MIPTM) on as-polished samples prior to etching. The results are analyzed in terms of the influence of applied strain and microstructure conditions on the propensity to cavitation of the alloy.

Jan 1, 2015

By T. G. Joseph, A. Sharma

ABSTRACT: Ultra-class haul trucks operating in oil sand face operational and maintenance issues as a result of soft underfoot conditions (Joseph, 2002). With exposure to frequent high g loading events, tire life is reduced due to sidewall belt fexure and frequent ground contact. Therefore, an improved under-standing of the interaction between tires and oil sand is needed. This paper examines the outcomes of a series of static and cyclic loading tests, performed using a scale tire on rigid, sand, and oil sand surfaces. Geometric predictions are made regarding the footprint area and vertical deformation of an ultra-classtire on similar surfaces.

Jan 1, 2011

By J. R. Perumareddi, V. S. Sastri, M. Elboujdaini

It is well known that high strength steels used in aerospace industry, are generally susceptible to hydrogen embrittlement during surface treatment such as electroplating with zinc on cadmium. Hydrogen embrittlement reduces ductility and results in brittle fracture rather than failure by plastic deformation. Hydrogen embrittlement of high strength steels is mitigated by surface treatment such as plating with other metals. Data on the hydrogen contents of steels before and after surface treatment by hot extraction-thermal conductivity, secondary ion mass spectrometry (SIMS) and UV-visible spectroscopy along with the mechanism are presented.

Jan 1, 2006

By D. R. Winchester

"I wish to thank you and your organizers for inviting me to address you at this point in time when we are all concerned for the future of the mineral industry in Canada.My topic ""Some Initiatives of Government Assistance to Industry Applicable to Mineral Processing"" is purposely limited in scope. To cover the entire range of initiatives in detail would take me all day, and at best, would be a mere recital of program titles, and a one sentence summary of the contents of the program. As you know, OREE or Regional Economic Expansion, is in the process of being amalgamated with elements of the Department of Industry, Trade and Commerce. We will become Regional Industrial Expansion or ORIE. If the name Canada Dry becomes popular, I don't think we will object as we hope to become a good mixer. The entire departmental thrust has been re-evaluated, and is in the process of being re-constituted to better serve the nation, and industry as a whole. Amalgamation of the industrial, trade promotion and marketing support skills of IT&C, with the regional development orientation and decentralization program delivery mechanisms of DREE, will, it is believed, provide better support to industry on a national and regional basis."

Jan 1, 1983

By Guy Demers

"This paper defines the responsibilities and functions of the Maintenance Department, and its organization, physical and human assets, highlighting the unique operating problems. Due to the self-sufficient aspect of the Asbestos Hill Deception Bay project, the Maintenance Department cover-s fields that are numerous and very dissimilar: production, mobile, processing, service, power generation, fire protection, heating, water and sewage disposal equipment. Added to this, buildings, plant and camps, wharves and communications equipment all demand versatility, adaptability and expertise from maintenance personnel. Good maintenance practices are a necessity in this environment and are more critical than at southern locations; that is, high-quality replacement material, complete and well-controlled preventive maintenance, major repairs on a component-replacement basis, updated inventory, efficient training and permanent contacts with suppliers, combined with an equipment improvement program, updated specifications on lubricants, hoses, seals, filters, etc., are mandatory. The seasonal aspect of the operations applies a great deal of pressure on the maintenance team, as the production months do not permit major repairs. Short- and medium range planning and accurate evaluation of equipment conditions highly influence production efficiency. Maintenance control, planning and scheduling do not follow the accepted standard routines, as personnel turnover normally does not permit an accumulation of knowledge of the equipment history and condition by the •individual tradesman."

Jan 1, 1976

By M. Buarzaiga

High-pressure acid leaching (HPAL) of nickel laterite ores typically extracts 95% of the nickel and 91% of the cobalt. Impurity elements in the feed, such as iron, aluminium and chromium, also dissolve and can be detrimental to downstream processes. Rejection of impurities within the autoclave is highly desirable. Aluminium and iron hydrolyze, and then precipitate in the autoclave leaving only small amounts that are subsequently removed by precipitation in a neutralization step. The concentration of dissolved chromium can range from 200 to 2000 ppm, depending on the feed composition. Chromium in the liquid phase, usually in the hexavalent state, introduces many problems and can limit refining options. For example, chromium poisons the organics in solvent extraction making SX an expensive option. Also, hexavalent chromium must be converted to the trivalent state before it can be precipitated along with iron and aluminium. Bench-scale work confirmed that mixing small amounts of carbon-base additives, such as coke, with the autoclave feed significantly reduced chromium concentration in the autoclave discharge without any detrimental effects on paymetals recoveries and selectivity.

Jan 1, 2004

By Adam Turcotte

Mining operations consume a considerable amount of energy, and while reduced energy consumption is desirable, it is not always clear how to achieve this goal. Understanding the opportunities to optimize energy consumption is crucial, and the key to understanding is visualization. One option is the Sankey diagram, which has been used for over 100 years to visualize the flow of energy, materials, or cost through various processes. However, there are drawbacks to this approach that must be addressed. In a Sankey diagram, each flow is represented by an arrow possessing a width proportional to the magnitude of the flow it represents. The diagrams show input flows, how energy is converted and into what form, and also output flows. As per the first law of thermodynamics, the total energy output is equivalent to the total energy input, so any energy that is not transferred to another process is considered to be wasted. These waste flows are depicted in Sankey diagrams and make it straightforward to associate energy sources, sinks and waste flows. Unfortunately, Sankey diagrams do not convey all information required to support practical decision making for redirecting individual energy flows. Based only on a Sankey diagram, it may become evident that a significant flow of waste heat is of the appropriate grade (temperature) and volume to meet an on-site heat demand currently being met with paid-for, possibly carbon intensive fuel. However without augmenting the Sankey diagram with 3D spatial, true geometric analysis, the practicalities of the concept or idea may not be fully appreciated. Another issue with a Sankey diagram is that the magnitude of the energy flowing between processes may have temporal fluctuation or variability on different timescales (diurnal, seasonal, interannual). Currently, Sankey diagrams only provide a static picture of energy conversion and consumption, so that, for example, 4 separate diagrams could have to be prepared for each season. A new energy flow visualization technique which we have called Sankey Trees has been developed. Process locations are defined within a 3D model of the site being studied, and the magnitude of the flow between each pair of processes considered is replaced with a time series. Branches of sustained and diminishing flows are represented through variation of the geometric properties of the branches of the trees. These branches are animated to indicate the direction of flow, and branch joints are used to indicate that a process is transporting one form of energy to multiple processes.

Aug 1, 2013