Search Documents

By P. E. Cavanagh

THE Ontario Research Foundation has developed a family of dry magnetic concentrators which, when used in conjunction with a dry grinding mill such as an Aero-fall mill, will allow the production of a completely dry magnetite concentrate. Previous experience with extrusion of iron ore and with pelletizing of fine iron concentrates suggested that it might be possible to develop a method particularly suited to the agglomeration of completely dry concentrates which might have some practical advantages over other methods of agglomeration. Pelletizing is the preferred method of agglomerating very fine iron ore concentrates. Magnetite concentrate is fod to the pelletizing equipment in the form of a moist filter cake. Binders and plasticizers may be added if necessary, and the moisture content must be increased or adjusted to the percentage necessary to give good balling action and satisfactory green strength in the resulting moist pellets. The moist ore with a closely controlled water content of about 7 to 12 per cent moisture may be rolled into pellets by a snow-balling action in a pelletizing drum, a Lurgi pan, or a Mac-Dowell disc pelletizer. The resulting green pellets are fired by one of several alternative processes to produce a hard pellet which has sufficient strength to withstand handling and shipping.

Jan 1, 1957

By P. G. Hallof

The exploration staff of Campbell-Chibougamau Mines Limited has used past experience to delineate several areas of geologic interest under Lake. Chibougamau. Du• ring the winter of 1964-65, a reconnaissance induced polarization survey was carried out on the lake. First, several lines were surveyed over the known mu1.erahza-tion at the Henderson mine; the grid was then extended into the areas of interest. Several anomalous zones were located and drilled; one, of these proved to be of economic interest.

Jan 1, 1967

By DON E. MacDONALD

Marl in Alberta is confined to highly specific geological, hydrogeologica/ and climatic settings. Tufa is fa irly abundant in those areas of western Alberta where bedrock is of the Paskapoo Formation. Marl and tufa originate when the following conditions are met: presence of a carbonate source in drift or nearsurface bedrock; leaching of the carbonate by percolating groundwater; transportation of calcium and bicarbonate ions in a permeable aquifer; discharge at the surface as springs, seeps or lakes; re-precipitation of calcium carbonate. Alberta has seven categories of marl and tufa deposits, based upon over-all depositional environment and calcium carbonate

Jan 1, 1984

By P. G. West-Sells

At Barrick's Zaldivar Copper Mine in Chile, the addition of sulfuric acid to the ore going to heap leaching is a major expense. A process in which a portion of this acid is replaced by elemental sulfur added to the heap has been developed by Barrick and Westcoast Biotech that has the potential for significant cost savings. Initial shake flask tests with plant raffinate solution indicated that oxidation of elemental sulfur by a culture of sulfur-oxidizing bacteria, some indigenous to the Zaldivar heap, showed a significant lag period. This lag period could be reduced by dilution of the raffinate, but dilution would not be economical to implement at Zaldivar. Short (0.75 m) column tests indicated that after the initial lag period, sulfur biooxidation occurred steadily and the acid requirement for obtaining the same copper recovery as the control without sulfur was reduced by as much as 13 kg/t. These tests were followed by taller (5.1 m) column tests that confirmed the reduction in acid consumption, with no negative effect on copper extraction.

Jan 1, 2007

By F. Y. Hsiao, H. C. Kao

Underground excavation in hard rock is normally stable at shallow depth except for wedge failure. However, the excavation depth is rapidly increasing recently. In high overburden stress condition, the integrity of rock would be destroyed with degrading rock strength. Therefore, understanding both the peak and the post-peak strengths of hard rock are necessary to assess the tunnel stability at depths. The characteristic of the post-peak strength is seldom studied in Taiwan in the past. Various estimation methods for the post-peak strength degradation were briefly reviewed in the paper. Based on the Geological Strength Index (GSI) system is widely used in the determination of the rock mass strength, the quantitative residual GSI system was adopted to estimate the possible strength degradation for a hydraulic tunnel in Taiwan. The Mohr-Coulomb model (no strength degradation) and the post-peak strength degradation model (strain softening model) were used to simulate the excavation of the case tunnel at different depths. The analyses demonstrate that the tunnel is in stable condition at 600m of depth. And the effect of the postpeak strength degradation on tunnel deformation is progressively significant with increasing tunnel depth. Approximate 3-5 times of increase in crown settlement and horizontal convergence would occur when post-peak strength degradation are considered at 2400m of depth. Severe tunnel deformation may endanger the tunnel stability. Modeling results reveal that the post-peak strength degradation has a great effect on tunnel stability under high overburden stress condition, which should not neglect in deep tunnel design.

Jan 1, 2015

By S. S. Al-Thyabat, A. M. Ghrair

"Printed circuit board (PCB) is the main part of any electric or electronic device, providing mechanical support and electric connection for the board eclectic components such as capacitors, resistors, diodes etc. PCB consists of non-conductive substrate overlaid with one or more layers of copper sheets. They also contain appreciable amounts of base metals (copper, nickel, tine, and aluminum) and precious metals (gold, silver, and rare earth elements (REE)) which end up in the landfill at the PCB end-of-life.PCB recycling E-waste in general is a profitable business; many valuable raw materials, precious and base metals, can be extracted with high purity. Approximately, one metric tonne of PCBs may contain 80-1500 g of gold and 160–210 kg of copper. The precious metals recovered from PCBs occur at concentrations higher than commercially mined minerals. Also PCB recycling is very important to our environment since many heavy metals (e.g. lead) may be leached from the landfills to the underground reservoirs. In Jordan, however, the work conducted on E-waste and PCB recycling in particular is limited; currently most of the E-waste is either exported or dumped in the landfill.In this work, a combination of physical (magnetic separation), physicochemical (flotation), and chemical methods (leaching) were used to compare metals concentrations in leach liquors produced from a concentrates resulted from a combination of these methods. It was found the leach liquor of the magnetic fraction of the PCB coarse size gave the highest concentration of Fe, Al, and Ni while concentration of Cu was higher in leach liquor of nonmagnetic sink fraction. On the other hand, metals concentration almost similar for both sink and float of the fine size fractions, indicating even distribution of metals concentrations in the fine size fractions."

Jan 1, 2016

By K. Ihara, R. Akiyoshi, Y. Takaki, S. Kang, H. Shishido

"Tensile tests and scanning electron microscopy-electron backscattered diffraction (SEM-EBSD) analysis were performed in an Al-Mg-Si alloy to clarify the effect of annealing and cold-rolling reduction on the texture formation. The hot-rolled specimens were cold-rolled with the reduction of 58-75%(CR1), followed by annealing at 773 K for 5 min(IA). The secondary cold-rolling(CR2)for the IA specimens with the reduction of 33–66%, followed by the solution heat treatment(ST), were performed. Focusing on the CR1 and CR2 specimens, the average r-values increased with higher primary and lower secondary cold-rolling reduction, respectively. This was considered to be due to the increase of r-values measured in the direction of 45 degree with respect to rolling direction, caused by the formation of the ß-fiber components (Brass {011}<211>, Copper {112}<111> and S {123}<634>) with high density. Based on the texture analysis of annealed specimens it was suggested that the high density of the ß-fiber components after IA and the small amount of stored strain energy of CR2 introduced by the lower cold-rolling reduction remained the ?-fiber components even after solution treatment.INTRODUCTION Al-Mg-Si alloys have been applied to automobile body applications, due to their excellent paint-bake hardening (age-hardening) and corrosion resistance compared to other aluminum alloy. On the other hand, the mechanical properties and deep drawability of Al-Mg-Si alloys are inferior to those of steels. Thus, it is important to improve the mechanical properties and deep drawability in order to expand the application components. One of the best methods to improve the deep drawability is to increase the Lankford coefficient (r-value). Previous studies reported that the increase of the average r-value ( ) improves the deep drawability. The relationship between the r-value and texture of the alloy is also well known. Inoue et al. reported that the ß-fiber components, such as Brass ({011}<211>), Copper ({112}<111>) and S ({123}<634>), increase the r-value measured in the direction of 45o with respect to the rolling direction. r"

Jan 1, 2018

By MAX VOS

Lithium is the lightest and electrochemically most reactive of all metals. Renewed interest in lithium coincides with research in lithium batteries and power generation by atomic fusion. Ontario lithium resources are contained in spodumene pegmatites that can form where medium- to high-grade metamorphic volcanic-sedimentary formations are intruded by pegmatite and porphyritic granitic rocks. Spodumene pegmatites occur in at least twelve locales throughout northern Ontario, all of which are in the Superior Province of the Precambrian Shield. Tantalum, cesium, rubidium, beryllium, niobium and tin also were noted with lithium in spodumene pegmatites. Considerable potential remains for discovery of additional lithium and rare-element pegmatites in northern Ontario.

Jan 1, 1984

By C. Dupuis, P. Waite, S. Leboeuf

Casthouses throughout the aluminium industry commonly use chlorine gas as a fluxing agent for furnace and in-line treatment of molten aluminium alloys. Its positive impact on the removal of alkali elements and non-metallic inclusions is well known. Nevertheless, the elimination of its use is highly desirable due to the safety and environmental risks associated with storage and handling. Over the past decade, the aluminium industry has significantly reduced its chlorine consumption. This has been achieved by maximizing the chlorine gas utilization efficiency during metal processing, and by the chlorine replacement for crucible and furnace metal treatment applications. Operation of sealed in-line treatment units without chlorine is now possible, but with lower or inconsistent removal efficiency penalties for alkali and inclusions respectively. This paper reviews the progress made at Arvida Research and Development Centre regarding the reduction of chlorine and the development of an alternative to chlorine for in-line metal treatment without penalizing the metallurgical performance.

Jan 1, 2006

By Victor F. Hollister

Although none of the deposits discovered to date are of commercial interest, significant Frasch or sedimentary sulphur deposits occur in Nova Scotia in Upper Mississippian Windsor Group evaporites. The evaporite sequence contains anyhdrite and is overlain by impervious shales. It also is •mderlain by locally petrolijerous formations that are potential hydrocarbon sources for reaction with anhydrite to produce sulphur. As well, stratigraphic and structural traps are known to exist in the Mississippian beds. Thus, all requisites for sedimentary sulphur genesis are present. Available hydrocarbon sources are numerous but small; resultant sulphur deposits therefore are probably also small. Evidence suggests, however, that sulphur deposition is not yet complete.

Jan 1, 1984

By I. Raheb, M. Y. Debili

"A set of Al-Co binary alloys (with respectively in weight percent 10%, 20%, 30%, 40%, 50% and 60% Co) have been studied by X-ray diffraction at the as compacted state. The structural evolution according to cobalt addition shows special features as the apparition of fcc cobalt and hcp cobalt beside aluminium in some cobalt compositions of the Al-Co mixtures using only cold compaction without sintering at high temperature. Figure 1 Cobalt is not a common alloying element in aluminium because its solubility is very low [1]. According to the pressure-temperature phase diagram, Co is known to exist in two allotropic forms: a low-temperature hcp phase and a high-temperature fcc phase [2-3]. At room temperature, Co is stable in the hcp form but it transforms to the fcc form when it is heated to above the transition temperature 695K. Powder aluminium and cobalt (99.999 %) were used in the proportions defined according to the required compositions. The total mass of the samples to be elaborated was between 8 g and 10 g. Cold compaction of mixed powder (Al-Co) under an uniaxial load of 10 MPa has been achieved to obtain a dense product (60%)."

Jan 1, 2015

By Sunil S. Gandhi

"The Mountain Lake deposit is a tabular sandstone-type uranium deposit, hosted by the basal unit of Middle Proterozoic Dismal Lakes Group. Uranium occurs mainly as sooty pitchblende disseminated in stratiform lenses within gently dipping quartzose sandstone. It is associated with copper sulphides, pyrite, hematite, and traces of nickel and cobalt arsenides and of silver.Exploration HistoryUranium showings on the PEC claim group were discovered during 1969 by an airborne radiometric survey carried out over the Dismal Lakes-Great Bear Lake area by Aquitaine of Canada Limited (Bizard and Salat, 1969). Some drilling was done in the vicinity of the showings in 1975 by the company under a joint venture with Eldorado Nuclear Limited but the results were not encouraging (Hassard and Woollett, 1975). During 1972, Trigg, Woollett and Associates Limited conducting surveys for Imperial Oil Limited, discovered numerous high-grade radioactive boulders scattered over a distance of several kilometres north and west of the showings, and the area north of the PEC claims was staked as the YUK claims (Ahuja, 1974). A systematic study of the boulder distribution and Pleistocene geology suggested a source additional to the showings. More intensive exploration followed, and in 1976 drilling just north of the PEC claim group boundary intersected the main deposit at a depth of 75 m to 150 m, beneath overburden up to 60 m thick. Part of the deposit extends into the PEC claim group which is under exploration by the Aquitaine-Cominco Joint Venture.The following brief description is based on the presentations in 1978 by F. Hassard of Trigg, Woollett and Associates Limited at the Geoscience Forum in Yellowknife, and by S.S. Gandhi of the Geological Survey of Canada at the Mineralogical Association of Canada Uranium Short Course in Toronto."

Jan 1, 1986

By E. O. Magnusson

THE orebodies of the Preston East Dome mine show a considerable variation in size,? shape, dip, and ground condition. They vary from small and large irregular masses being mined by shrinkage, cut-and-fill, and square set-and-fill mining methods to narrow veins being mined by open stoping. Standardization of mining operations has necessarily been difficult. This considerable variation in mining condition prompted the development of a bonus system which would give more equitable bonus payments through-out the mine than those obtained by the usually accepted methods of calculating mine bonus. PRINCIPLES ON WHICH THE SYSTEM IS BASED Under an incentive bonus system, performance (efficiency) and a price per unit of work done are inter-related. It is in the application of this? principle to working conditions .in the Preston East Dome mine that the system to be described differs from the standard methods of calculating mine bonus. It was found that the method of paying a fixed price per unit of work done, under the &apos;contract&apos; system, gave satisfactory results in development, less satisfactory results in timbering, and results which were not satisfactory in stoping. Under the fixed price system, bonus payments, in timbering and stoping particularly, were very erratic and did not necessarily represent fair payment for the work done. A fixed price in development is satisfactory because the work done, and the conditions under which the work is done, are uniform. The drilling and blasting cycle is completed in one shift, the size of heading is con-trolled, and a minimum number of holes are required in order to obtain a satisfactory break. The performance possible under these conditions has been found to be confined to a fairly narrow range. By performance in development is meant the efficiency of the working crew as expressed in terms of the two variables of feet of advance per round and pounds of ex-plosives consumed per foot of advance. A change in rock formation, how-ever, may alter to a marked degree the performance possible, quite independent of the skill and energy of the working crew. The changes in working conditions that affect development performance from the standpoint of bonus calculation are usually easily apparent and are satisfactorily met by establishing several fixed prices.

Jan 1, 1944

By M. Hall

"SomarioEl circuito de molienda a Selbaie consta de molino semiaut6geno en un circuito cerrado y molino de balas en un circuito cerrado. El amperaje del motor de se usa controlar el tonelaje el molino. Este sistema estabiliza el circuito pero no mejora activamente el rendirniento del circuito. Se desarroll6 auxiliar el rendimiento del circuito un sistema experto en manipular las objetivos de existir control proporcional-integral. Se ejecut6 el sistema con el Comdale /C conjunto del sistema experto y ha side funcional hace tiempo el mayo de 1992. El sistema experto ha resultado en un aumento en tonelaje de 7tph y una disminuci6n de $210,000 en el caste anual de media de molienda. Se describe el desarrollo del sistema y los provechos derivar se presenta.AbstractThe grinding circuit at Selbaie consists of SAG mill and ball mill closed circuit grinding. The SAG mill motor current is used to control throughput. This system stabilizes the circuit but does not actively optimize circuit performance. An expert system was developed to aid the optimization of the circuit by manipulating the set-points of existing PI control loops. The system was implemented with the Comdale /C expert system package and has been on line since May 1992. The expert system has resulted in a net increase in tonnage of 7tph and a decrease in annual grinding media costs of $210,000. The system development is described and the benefits derived are presented."

Jan 1, 1994

By John S. Stevenson

THE Twin "J" Mine, operated by Twin "J" Mines, Limited, represents an amalgamation of the old Lenora, Tyee, and Richard III mines (see Figure 1) on mount Sicker, eight miles by road, northwesterly, from the city of Duncan, on Vancouver island. These mines produced 253,000 tons of copper-gold ore between 1898 and 1909 (see Table I). During the more recent period of production from these properties, July, 1943, to May, 1944, Twin ?J? Mines, Limited, mined and milled ore with values mainly in copper and zinc, and minor values in gold, silver, and lead. Figures are not available for this later production. Field work at the property was started by the writer in 1941 and continued in 1943 and 1944.

Jan 1, 1945

By Kati Tschöpe

Cathode wear has become an increasing challenge in the aluminum industry due to the use of more graphitized materials. Today, there exist no standard laboratory methods for measuring cathode wear where different commercial materials can be ranked. The typical average wear rate in an electrolysis cell is quite small. The aim of this work was to design a test method where the wear could be accelerated compared to industrial cells. It was focused on polarized tests where the cathode is exposed to electrolyte, which gives higher aluminium carbide solubility. The cathode materials were characterized by microscopy and image analysis.

Jan 1, 2011

By A. G. Pathan

Rock and soil mechanics investigations were carried out in block VIII at Thar Coalfield, Pakistan. Most of the strata were mainly composed of sand, with an average content of 67.68 %. Laboratory studies of rock and soil samples from drill hole GT-01 revealed that the strata in block VIII are very weak with an average uniaxial compressive strength of 3.59 MPa, an average tensile strength of 0.68 MPa, an average Young?s Modulus value of 0.234 GPa, an average cohesion of 129.19 KPa, and an average friction angle of 55.47°. Slope stability analysis, based on a probabilistic approach, was carried out using Slide-V software. Monte Carlo simulations have been applied to investigate the probability of failure in the slopes of an open pit lignite mine in block-VIII. From the slope stability investigation, it was found that the probability of failure is 0 % at a slope angle of 16°.

Aug 1, 2013

By R. O. Burt

The original flowsheet of the TANCO mill consisted of a simple two-stage gravity circuit for the recovery of the tantalum concentrates. With decreasing grade and grain size of the tantalum minerals, considerable modifications to the circuit have been required. This paper discusses the various recent improvements carried out 011 all stages of the flowsheet, which have resulted in a 10% increase in recovery. Future improvements, including on stream analysis, and the possibility of tantalum flotation , are also discussed.

Jan 1, 1979

By Miguel A. Cuba

Trends in the mean and/or variance are a longstanding challenge in mineral resource modeling. Geologic modeling and/or grade domaining are often employed to account for heterogeneities in mineral grades; however, this is only practical up to a certain point since the number of data available for reliable model construction can be severely reduced. In such cases, trends remain present in certain geologic/grade domains and directly impact the modeling methodology; the trend must either be handled explicitly or a suitable approach is adopted to implicitly account for it. This is highly dependent on understanding the source of the trend. We propose an approach that detects the source of non-stationarity, which is based on quantifying the impact of non-stationarity in the mean and the variance via the semivariogram. By expanding the methodof- moments approximation of the semivariogram, we decompose the experimental semivariogram is into three terms: 1) trend in mean component, 2) trend in variance component and 3) stationary component. We can then assess the source of trend by calculating the contribution of each component at every lag. Two cases are presented to illustrate this tool. Firstly, a synthetic reference model is simulated and different trend patterns are added; the influence of these patterns in the experimental semivariogram calculation are analyzed and discussed. Secondly, a real dataset is considered where the impact due to the presence of trends in the mean and variance are assessed. The results of this paper reveal the semivariogram to be a tremendously powerful tool in determining the source of the trend. This insight may be useful in the selection of a suitable modeling approach for resource estimation.

Oct 1, 2009

By M. Reda

Because of the adverse environmental effect of Chromate, Molybdate ions had been investigated as replacement for Chromate and the results had shown not to be encouraging. Film deposited from peroxopolymolybdate (from reaction of Molybdenum meta, with excess Hydrogen Peroxide), are more robust than that deposited from molybdate solutions. This was shown to be due to higher fraction of Mo (IV) and Mo (V) that form from Mo (VI) in the peroxopolymolybdate deposited film than the film deposited from Molybdate solutions. The peroxopolymolybdate film contains 40% un-hydrated molybdic acid, tetraperoxodimolybdate and tetra peroxo tetra molybdate. The protective properties of peroxopolymolybdate were shown to be due to the effectiveness of the un-hydrated molybdic acid.

Jan 1, 2010