Search Documents

By A. Boeing

Rock-breaker automation and remote operation improves the safety and efficiency of mining operations. This article presents an overview of the Rocklogic rock-breaker automation system architecture that provides collision avoidance, automated parking, and remote operation functionality. The system consists of a distributed computer control system that interfaces with sensors attached to the rock-breaker, the rock-breaker hydraulics, and the site infrastructure. We present results of an automated Transmin rockbreaker installed in a production environment at an underground Australian mine site. The system has been in production use for over 900 days during which there have been no reported collisions, and 100% adoption of the remote operation technology. As a result, Rocklogic has significantly improved the safety of rock-breaking operations and reduced the rock-breaking cycle time, thereby improving the sites overall throughput.

Aug 1, 2013

By Liang Zhen, Jian-Tang Jiang, Guo-Ai Li, Xiao-Ya Wang

"Deformation behavior of 2A97 aluminum alloy containing coarse secondary phases was studied using uniaxial hot compression (HC, 340–490°C, 0.4001–1 s-1). The flow stress could be described by a Zener-Hollomon parameter in hyperbolic sine function with the hot deformation activation energy of 237 kJ/mol. Based on the experimental data and dynamic materials model, processing maps were generated to demonstrate the hot workability of the alloy. The coarse secondary phases experienced dissolution by varying degree under different deformation temperature, which producing different effects on the microstructure evolution. When deformed at relatively low temperatures, a mass of fine grains shaped up in the original grains and grain boundaries, and the dominating deformation mechanism was believed to be dynamic recrystallization. As the deformation temperature rising to 490°C, most secondary phases disappeared and few recrystallized grains were observed, indicating that the secondary phases dissolved sufficiently along with dynamic recovery occurred during the hot deformation. Particle stimulated nucleation related to the coarse secondary phases was believed to promote the recrystallization and the recrystallization behavior was sensitive to deformation temperature.INTRODUCTION Al-Li alloys has received much attention as new promising structural materials in the aircraft and aerospace industries, due to their lower density, higher elastic modulus and improved fatigue crack growth resistance in comparison with the conventional commercial aluminum alloys (Ou Ling, 2015). 2A97 alloy is one of the 3rd generation Al-Li alloys targeting at comprehensive improvement of aviation aluminum alloy and applications for wing spars and ribs to other internal structures for transport aircraft. Al-Li alloys are usually formed by hot deformation, either by rolling or extruding. The deformation behavior and resulted microstructure evolution during the forming process mainly dominates the formability of the alloy and the serving performances as well. Therefore, the deformation behavior and microstructure evolution at elevated temperature need be made clear for optimizing the hot processing parameters and controlling microstructure evolution."

Jan 1, 2018

By W. G. Jeffery

"The mining and mineral industries have been, and remain, a major component of the Canadian economy. There are approximately 560 producing mining establishments of which there are some 130 metal mines and an equal number of non-metal mines, the balance being quarries for stone, sand and gravel. For 17 metals and minerals, Canada ranks within the top five as a world producer. There are 29 metallurgical plants. Employment in mining, smelting and refining was about 150000 in 1990. Mineral production, including coal, is about $20 billion. Exports up to the metal stage amount to $15 billion providing a positive trade balance of some $10 billion.The producing industry has a wide diversity of products. The companies range from small single mining operations to large multinationals. In terms of technology the industry has always been in the forefront of cost-effective practice, either using home-grown innovation or freely importing technology from around the world,The Mining Industry Technology Council (MITEC) makes an annual survey of the exploration and R&D expenditures of the senior mining industry that is the mining companies that are involved in mineral production from their existing mines. It does not include those companies solely involved in exploration using funds raised through equity sales.Table 1 shows the actual R&D and exploration expenditures as a per cent of sales. R&D shows a rising trend since 1988although the drop in value of output due to lower prices must be recognized as contributing to the increase. The point about this compilation is that the mining industry re-invests some 4070 of its sales in both exploration and R&D in order to sustain itself. Exploration for the renewal of metal inventories for future mining is a process unique to mining. It is not classified as R&D, and the necessity for this investment goes unrecognized by those who state that the industry does not do enough R&D."

Jan 1, 1993

By J. W. Matousek

"More copper concentrates are treated in flash smelting furnaces than by any other process, and such furnaces are located in most of the world's major copper producing areas. Except for perhaps two furnaces treating chalcocite-type materials, little difference is seen between the grades of the concentrates being smelted. Within individual smelters, even less variation in feed grades is found. This is both accidental and intended. Many furnaces treat concentrates from captive ores, and these tend to be of relatively constant composition over long periods. Toll smelting operations blend concentrates to ensure delivery of feeds of fixed compositions to their furnaces to avoid upset conditions. Matte grades vary between flash smelting furnaces, but most commonly, these are the result of differences in operating practices rather than because of differences in concentrate grades. This paper reviews an industrial flash smelting test in which the copper content of the furnace feed was intentionally altered over a wide range. IntroductionExcept in a few copper mining regions of the world, the principal copper mineral is chalcopyrite (CuFeSz). This results in the almost universal production of concentrates containing 25070 to 30% copper (and similar amounts of iron and sulphur). Many operators of copper flash furnaces spend their entire metallurgical careers smelting concentrates of essentially fixed grades. This is true both of smelters treating concentrates from captive mines and those processing concentrates on a toll basis. From the production staff's point-of-view, the less variation in grades seen by the furnace, the better. Fixed analyses of concentrates and constant feed rates produce consistent quantities of matte at a consistent grade for processing by the converters. The result is, even in smelters treating a variety of concentrates, efforts are expended in sampling and blending to ensure feeds of relatively uniform compositions being sent to the furnaces."

Jan 1, 1993

By A. I. A. Salama, M. W. Mikhail, R. J. Mikula

"The Coal Research Laboratory (CRL) of CANMET along with other research organizations in coal-producing countries envisage major benefits from computer applications in coal preparation, Some of these benefits are greater system flexibility, improved coal preparation plant performance efficiency and efficient utilization of manpower, all of which result in economic benefits. Computers can be applied for both on-line and off-line purposes; this paper focuses on the on-line applications from the process control point of view.A critical discussion of the different analog and digital process control systems is presented. Recent developments in Great Britain, West Germany, Poland and Australia on automation and instrumentation using on-line measurements of coal ash and moisture contents are identified.The CRL research and development strategy aimed at achieving on-line computer control of an automated coal preparation plant is presented.IntroductionIn the past twenty years an enormous progress in the area of computer technology has been noticed. Computer applications in industrial processes offer greater system flexibility, improved plant performance efficiency and efficient utilization of manpower. Significant computer control development in mineral processing has already been achieved. Although progress has been made in the area of computer applications in coal preparation, more effort is needed to utilize the full potential.The computer applications in coal preparation can be viewed as off-line and on-line. Considerable progress has been reported in the area of off-line computer applications, especially in the areas of modelling, performance evaluation/prediction and statistical analysis. However, only modest progress in on-line applications has been reported(1-7). This paper will focus on: online instrumentation and process control applications, different analog and/or digital control systems, on-line automation and instrumentation in other countries and CRL strategy toward pilot plant automation."

Jan 1, 1985

By D. J. Farmer

Mining hoists are major components of any underground mine, however, the detailed design work required to get the actual power required for a particular hoist is outside the scope of preliminary feasibility studies. Nonetheless, a hoist is costly. Therefore, an accurate estimate is needed for the design parameters and the power required. There are two methods available, namely, the O’Hara method and the Society of Mining Engineers’ method. Tests were done for both methods employing nine friction hoists and 19 drum hoists currently in use at Canadian mines. The O’Hara method provided unacceptable results for both friction and drum hoists. While, the SME method was designed for American regulations and factors of safety which often differ significantly from Canadian ones, good results were obtained. The two relationships deter-mined were simply to add 5% to friction hoist design and to add 4% to drum hoist design. Modifying the SME method by these two factors will allow the hoisting system determined by the SME method to be within the error for a prefeasibility study.

Jan 1, 1997

By Sylvain Castonguay, Sylvain Pilon

"Operator competency is an important factor in the safe and successful operation of today’s complex processes. Competent process unit operators deliver superior performance and results. In greenfield projects, operator competency is particularly critical, as the lack of specific operations experience must be offset with proven practical knowledge and skills to avoid mistakes that can cost millions in terms of start-up delays, production losses and equipment damage. It is, therefore, important to know precisely what competencies are required for a project or site, and what any gaps in operator competency need to be addressed and improved. The success of plant commissioning, start-up and sustainable operations is directly tied to operator competency. The significant investments required for new projects, the exploitation of more challenging ore bodies, and the increasing complexity of plant operations have placed renewed emphasis on the need for competent operators. Furthermore, many large capital projects are being developed in remote regions, often with ties to the delivery of social benefits for the local population in terms of jobs, training and other development opportunities. While automation and processing technologies have helped do more with less, indicators now point to a bottleneck in human performance limiting operational results.Automation industry development in managing abnormal situations, including solutions for simulation and operator training, has produced applications to provide customized and flexible training methods. This paper will discuss tools to automate the operator competency process in order to guide trainers to effectively teach, measure, control, provide feedback, and monitor operator skills. Today’s competency management solutions can be effectively applied throughout the course of an operator’s professional life, as a guide to hiring new operators, for developing competencies to support operations, and also to develop and refine best practices and share lessons learned."

Jan 1, 2016

By S. Rash Ahmadi

Welding is highly reliable and efficient metal joining process. In welding the metal adjacent to the weld joint is subjected to severe thermal conditions. As a result, complex changes in metallurgical structure occur in this region. These changes in structure depend on the material and the temperature history experienced. Friction stir welding (FSW) is relatively a new welding process in which, heat is generated by friction between the tool and the workpiece. The amount of heat conducted into the workpiece determines the quality of weld, residual stress and distortion of the workpiece. The objective of the current work is to study the transient temperature in a friction stir welding. So, a three dimensional transient analytical model is used to study the thermal distribution during the welding. Heat input from the tool shoulder alone is considered in the model. The process parameters like axial load, welding speed and tool rotational speed, used in actual FSW process are taken to build the model. This analytical model is very useful for select the optimized affected parameters in friction stir welding. The model illustrates the comprehensive equation including actual affected parameters in FSW and it can be used for different materials. In addition to the above the thermal history finds application in design of welding tools.

Oct 1, 2011

By K. E. Waters, N. Brodusch, R. Gauvin, H. Demers

"Rare earth elements are becoming increasingly in demand, due to their prevalence in both renewable energy devices and high-end electronics. The characterization of the composition, morphology and volume fraction of the various phases that have valuable rare earths in the ores are needed to find the optimal industrial process to extract the ores containing the rare earths. Rare earth-bearing minerals contain many elements with the M-and L-lines overlap, requiring a high degree of resolution, pushing the boundaries of scanning electron microscopy quantitative analysis. Enhanced microscopy at a high spatial resolution with improved x-ray quantitative analysis enables the accurate determination of the distribution of the desired rare earths in various mineral phases. INTRODUCTIONRare earth elements are becoming increasingly in demand, due to their prevalence in both renewable energy devices and high-end electronics. From batteries (lanthanum and cerium), to magnets (dysprosium and neodymium) and lighting (yttrium), the rare earth elements are crucial to the advancement of technology, and to energy saving devices (Crow, 2011). The goal of this project is to characterize the composition, morphology and volume fraction of the various phases that have valuable rare earths in the ores in order to estimate the economical VALUES (of the ores and to find the optimal industrial process to extract the ores containing the rare earths. High spatial resolution imaging and x-ray microanalysis are needed to reach this goal. In this work, the results obtained with a cold-field-emission scanning electron microscope (FE-SEM) and a silicon drift detector (SDD) energy dispersive spectrometry (EDS) detector at low accelerating voltage are compared to experimental conditions typically used with electron probe microanalysis (EPMA) instrument.With this improvement, a detailed scientific analysis of the composition of these, and other, ores will become possible with a SEM/EDS system. This will help to better understand how such ores were formed, hence assisting in finding them, and to better understand how to process them in preparation for high end industrial applications, namely through mineral processing."

Jan 1, 2012

By Donald S. Macdonald

"I AM thankful for this opportunity to address the Toronto Branch of The Canadian Institute of Mining and Metallurgy. The Members of your Institute can have a great influence on the direction in which the mineral policies of Canada will evolve, and to assure that optimum benefits from our country's vast mineral resources will accrue to the nation as a whole and to all its citizens. Today, I want to: (1) offer an outlook on the mineral industry for 1973; (2) talk briefly about the role of minerals in the total economy; and (3) outline some of our thinking with respect to a national minerals policy for Canada."

Jan 1, 1973

By I. Clauzier

"A new method of managing electricity to reduce costs andimprove profits is discussed. Before taking steps to better manage electricity, it is essential to understand the terms peak demand and energy and their effect on an electrical bill. Knowing how electricity is presently used in the plant is the important first step. This goes beyond knowing how much electricity is used at each time of day, the individual contribution of every plant process to the total plant load must be known. At this point, each process is ranked according to importance to production in order to identify possible savings opportunities. These improvements can then be implemented by simply improving operations or in some cases, through the use of an automatic control system. IntroductionIn today's competitive environment, controlling costs is becoming increasingly important. All costs associated with operation must be controlled in an effort to improve competitive position. Electricity is a cost component that can and should be managed.Although the term management can mean different things to different people, the intent is always the same: to make the best possible use of existing resources, whether labour, equipment or electricity.The simple approach to managing electricity presented in this paper consists of four steps.I. Understand Peak Demand and Energy. It is essential to understand the terms, peak demand and energy and their effect on your electrical bill.2. Know Your Present Electrical Use. The present use of electricity in the plant must be known. This goes beyond simply knowing how much is used at each time of day, to accurately knowing how each process is contributing to the total plant electrical load, and ultimately to the electrical bill.3. Identification of Savings Opportunities. With this information, energy savings opportunities for reducing the electrical bill and improving profits can be identified.4. Implementing Improvements. Having identified areas of potential savings, improvements can then be implemented in order of their significance. This could be a matter of simply improving operations, or in some eases may mean the use of an automatic control system.These four steps can result in significant dollar savings."

Jan 1, 1987

By A. Chamanara

The gross vehicle weight (GVW) of an ultra-class mining truck comprises the unsuspended weight below the struts plus the suspended empty vehicle weight, plus the payload. Theoretically, one third of the suspended total weight is supported by two front struts and two thirds by two rear struts. However, since the payload position is not fixed when placed in the truck body and varies from load to load, compounded by uneven haul road profiles, the truck structure experiences higher than normal stresses, which manifest in the reduction of the life of the truck via structural fatigue. The downstream effects are a decrease in production and increase in operational and maintenance costs. In order to control the dynamic forces causing the high stresses on the truck structure, both the haul road conditions and the load distribution in the truck body need to be investigated. The latter aspect is the prime focus of this paper. A field test has been conducted in an oil sands mine where the Caterpillar 797B trucks are loaded by a Bucyrus 495 shovel. The strut pressure readings are collected using the data-loggers on the trucks as well as the truck velocity associated with each reading. Rack, roll and pitch are the main key performance indicators (KPIs) that are calculated to study the adverse effect of an unbalanced payload and consequently the truck structure. Finally, the shovel bucket load passes within the truck body are simulated and a new method is suggested to improve the truck payload balance.

Aug 1, 2013

By S. A. Sadough vanini

In this paper, Stress-Strain-Temperature relations for Shape Memory Alloys are studied. Temperature effects on Shape Memory Alloys are different from those related to ordinary materials. In ordinary materials, elastic characteristics can be assumed to be constant in low temperature ranges, and only the deflection arising from temperature changes could be added to the elastic defection. As long as two phases of austenite and martensite could be present in Shape Memory Alloys simultaneously, elastic modulus follows temperature and temperature gradient. In continue a smart actuator is investigated considering a homogeneous cantilever beam. Beam bending is established by using shape memory wires. An initial strain is imposed to shape memory wires in a low temperature, and then, they are installed in the outer surface of the beam. Therefore, since the temperature is imposed in these wires and they cannot have free recovery strain, the compressive recovery stress will be produced in the outer surface. This will result in a deflection in axial direction of the beam. At first, beam deflection is calculated on the basis of theoretical relations and solving the relevant differential equations. Afterwards, experimental tests are performed on an elastomeric beam equipped with shape memory wires. When a voltage is applied, a temperature rise will occur in the wires; then, this temperature rise causes a deflection in the beam. Finally, the theoretical and experimental results? comparison indicates a good conformity. One capability of this actuator is its high flexibility, and by controlling the inlet current, the end-beam deflection can be controlled.

Oct 1, 2011

By P. J. Urso

"This paper discusses the mining problems encountered at the Fording River coal mine to date, and how they have been solved. All of the production now comes from surface mining, but underground hydraulic mining is planned and briefly described. Other facets of the operation, including markets, equipment and personnel, are covered. IntroductionFording Coal Limited was formed in 1968 to mine and market metallurgical coal resources held by the company in the East Kootenay region of southeastern British Columbia. The company, at its Fording River operations, holds approximately 48,000 acres of coal lands, having an estimated 2.0 to 3.0 billion long tons of metallurgical coal in place. (Although not a point for further discuss ion in this paper, the company also holds approximately 1.0 million acres of mineral rights. These consist primarily of coal in Alberta, potash and coal in Saskatchewan, and minor industrial mineral holdings of limestone, salt and bentonite in the three western provinces.)Fording Coal is owned 60% by Canadian Pacific Investments Ltd. and 40% by Cominco Ltd. Inasmuch as Cominco itself is owned approximately 54% by CPI, it is seen that the effective CPI ownership of Fording is about 82%. The company, originally staffed and managed by Cominco, has been independent since January, 1978, with its own board of directors, management, staff and employees.The company's head office is in Calgary, Alberta. The Fording River operations are located approximately 45 miles north of the Crowsnest Pass, near the Alberta/British Columbia boundary, only 95 air miles and 200 road miles from Calgary.A contract was signed in 1969 with the Japanese steel mills to provide 45 million long tons of metallurgical coal over IS years, commencing in 1972 at an annual rate of 3 million long tons per year. Despite some start- up difficulties, the mine and plant facilities achieved their rated capacities in 1975, producing and shipping at the 3-million-Iong-ton level. The coal specifications are shown in Table I."

Jan 1, 1980

By Sadough vanini Ali

Charpy impact energy of functionally graded steels produced by electroslag remelting in crack divider configuration has been modeled in various strain rates. It has been well known that majority of materials indicate different behaviors under different strain rates and temperatures. Therefore, modifying the elastic-plastic model considering the effects of strain rates and temperature gives us an acceptable prediction of these composites behaviors in impact test. In this investigation, graded steel was divided in to several layers in which the layers have the same strains under the impact. Constitutive equation describing the flow stress variations as a function of strain rates and temperatures, have been used to express the stressstrain behavior of layers. The parameter values of constitutive equation determined for all the layers via using the boundary conditions based on composite graded behaviors which were the characterized ferrite, austenite, bainite and martensitte phases. Consequently by applying the rule of phase mixtures and ascribing the impact energy of each layer to the area of stress-strain curve of the same layer, the whole impact energy of composite is the sum of layers impact energy with considering the layers volume fraction.

Oct 1, 2011

By G. Guzman

In the framework of the optimization of Teniente Converter operation the new system of automatic flux feeding through gar-gun was implemented in the Potrerillos Smelter, Codelco Chile, Salvador Division. The control algoritm based on simple iron and silica balance adjusted by empirical coefficients was incorporated in the logical programmer. The programmer works in real time gathering information from the plant instrumentation events and introduced chemical assays of concentrate, slag and flux. Through the auto-tuning of the automatic operation the criterions of optimal flux dosage were determined. Four month of operation of the automatic flux feeding system demonstrated the stabilization of magnetite content in the slag in the narrow range from 18 to 20% and the decrease of flux consumption, corresponding to annual savings US$ 340,000. Additionally, the automatic system helps operators in the control room in fast determination of optimal fluxing and avoid the errors in flux dosage affecting the slag quality and its impact on refractory wear.

Jan 1, 2007

By M. Hashemzadeh

The efficiency of water use is a top priority for the global minerals industry, especially in regions with limited freshwater supplies. In these areas, the freshwater shortage has prompted mining companies to search for alternatives to freshwater sources. Seawater has been proven to be a potential water source for mineral beneficiation and metal extraction processes. This study compares chalcocite leaching behavior with ferric chloride to that with cupric chloride. We carried out leaching tests with a highly pure chalcocite sample in jacketed reactors under fully controlled pH and solution potential. The effect of chloride concentration, oxidant concentration, and temperature on copper extraction was quantified in both cupric and ferric chloride systems. In the ferric chloride system, increasing ferric concentration showed a positive effect on the first stage of chalcocite leaching. In the second stage, increasing temperature markedly enhanced copper extraction. In the cupric chloride system, chloride concentration presented a considerable effect on both the first and second stages of leaching, while temperature had a remarkable effect only on the second stage. The findings of this study would be beneficial to mine operations aiming to replace fresh water with seawater for heap leaching of chalcocite. INTRODUCTION Mineral processing operations/plants are normally operated adjacent to mines which are often located in remote and arid area, such as northern Chile, southern Peru and Australia with limited access to fresh water (Liu, Moran, & Vink, 2011, 2013). Water scarcity in these areas has prompted mining companies to invest in sustainable technologies to reduce the water use and/or increase the water use efficiency. One of the current sustainable approaches in mineral processing operations is to replace fresh water with seawater. Seawater is now being increasingly used for mineral beneficiation and metal extraction processes (Hernández et al., 2015). Another application of seawater could be for heap leaching of copper secondary sulfides, mainly chalcocite. However, the high concentration of chloride ion in seawater may significantly affect leaching kinetics of copper sulfide concentrates and ores (Watling et al., 2014). Therefore, it is essential to develop a fundamental understanding of the leaching of chalcocite in chloride media.

Jan 1, 2019

By A Turek

The Lake Cinch deposit occurs in the Tazin gneisses on the footwall side of the Black Bay fault. Ore is localized by two faults, the Main Ore fault and the Cracking-stone River fault, occurring in shoots along the former and on tension fractures between the two faults. Faulting leading to the localization of the deposit is analyzed in detail and tied into the regional pattern. Pitchblende, the chief radioactive mineral, is investigated by X-ray and found to be of very small particle size. The relation-ships of U, Fe and Mn in the ore are established quantitatively, and Fe is found to bear a catalytic relation to U. The deposit is classed as belonging to Lindgren's mesothermal class. Mineralization is attributed to carbonate solutions, and the uranium is believed to have been trans-ported in the hexavalent state as the uranyl tricarbonate ion; analogy is drawn to a recently developed hydro-metallurgical technique for the production of uranium dioxide. Introduction THE Lake Cinch deposit is located in the Beaver-lodge Camp, Saskatchewan. The property was staked in 1948 and went into production in 1957

Jan 1, 1965

By K. Buxmann

Climate change is a subject of growing concern. Based on the International Energy Agency, about 19% of man made greenhouse gas emissions globally are generated by the transport sector. This paper will focus on the environmental aspects of the light-weighting in transport and the resulting savings of fuel and electricity. Aluminium is an option for lightweight applications in transport, with very high benefits not only in the use stage, but also in the stage of vehicle recycling. Life cycle assessment is used to quantify the relative benefits of light-weighting specific components of cars, commercial road vehicles, buses, ships and trains. A vehicle consists of many components, which are produced by different processes and undergo different types of end-of-life operations. This document does not intend to compare a generic aluminium vehicle with a generic "heavy materials" vehicle. It rather tries to use a pragmatic approach based on specific examples of components where aluminium is used and can be used in the design of new vehicles, also taking into account future developments. The case studies in this paper are based on real cases where aluminium was used. For each component, sensitivity analyses are applied to see the impact of specific parameters such as the end-of-life recycling rate and the use stage driving distance. Significant greenhouse gas savings by the use of aluminium are demonstrated for cars and even higher ones for trucks, buses, trains and ships. In addition, the total potential benefits of light-weighting with aluminium are shown on the global level.

Jan 1, 2007

By A. B. Szwilski

"The various elements of longwall mine design are reviewed, particularly as they apply to condition s in the coalfields of the Plains region of Alberta. The following recommendations are made: (1) optimum panel lengths of 1000 to 2000 metres; (2) face lengths of 100 to 150 metres; (3) the use of retreat methods; (4) the restriction of floor undulations to less than 15 degrees. IntroductionThis article considers the elements of longwall mine design and is part of a short study that has been made of the feasibility of longwall mining in the Plains region, Alberta, Canada. The Plains region, with about 20 million tonnes, accounts for more than 80% of the coal resources of Alberta. The coalbearing strata in the Plains region cover an area of about 95,000 square miles. The geological formations dip very gently toward the southwest and, from a mining point of view, may be considered horizontal. The depth of the coal seams varies from several metres to over 650 metres. However, it is not anticipated that underground mining will be extended beyond the depth range of 25 to 250 metre s.The coal seams in the Plains region have been subject to many small mining operations in the past. The majority of these small mines were limited to a depth of about 50 metres, working mainly by room-and-pillar methods, although hand-filled longwall mining was often used.The development of new underground mining operations in the Plains region will have to be on a 'start-from-scratch' basis, especially regarding the installation of equipment. Longwall mining is more mechanized than any other method of mining and requires careful attention for the selection of new and expensive equipment. There have been many proven longwall advance and retreat systems in Europe and North America; mining conditions in the Plains region are more similar to those in the United States. Therefore, it will be essential for new mining pro jects in the Plains region to commence with proven system s and equipment; in time, perhaps an experimentation process could be attempted as experience is gained.Generally, the coal face is the key factor in mine productivity, which depends a great deal on equipment reliability, training and experience of the operators. The original design of coal faces must be flexible enough to cater for potential improvements so that running time can be increased."

Jan 1, 1980