Search Documents

By Virginia Lawson, Adam Price

The rougher flotation stage is used to reject liberated gangue at a coarse size. Base and precious metals due to their high specific gravity tend to recycle in the grinding circuit and report to the flotation circuit at a finer size than the gangue from which it is being separated. Generally liberation levels of greater than 50% are achieved in roughing and thus a portion of the feed can be immediately upgraded to final concentrate. The proportion increasing as the amount of liberated mineral in the feed increases. Scalping out concentrate from the rougher can reduce the size of the subsequent regrind and cleaner circuits. Examples of alternative process design for circuits demonstrates that you don’t need large volumes to effectively recover all of the minerals – you need smart flotation. Several case studies will be presented where circuits can be significantly reduced in size by designing smarter – not larger. This paper describes case studies to test the amenability of the Jameson Cell to produce final concentrate from rougher feed. Metallurgical performance and plant design implications are discussed. Froth flotation has been used extensively for mineral concentration for over 100 years. Although the flotation cell design has changed, it has generally simply increased in capacity rather than increase in efficiency. Cell capacities of over 600 m3 are now being used in rougher flotation particularly for the lower grade ores where the amount of surface area for flotation is deemed less significant than the required volume. The plant design volume in rougher flotation comes from laboratory batch flotation tests and/or pilot plants. The volume required for the plant is calculated based on the laboratory residence time multiplied by a scale- up factor. Examples of laboratory to plant scale-up design are given in Dunne et al. (2010 part 2). The factors are usually between 2 and 3. A laboratory residence time of 10 minutes would equate to a plant design residence time of 25 minutes using a 2.5 factor. The volume of the required flotation cells can then be calculated using the design tonnage and volumetric throughput. This scale-up factor takes into account the differences in performance between batch flotation efficiency and full scale plant. The differences are likely related to inefficiencies of bubble particle contact in large cells as well as froth recovery, which is essentially complete in a batch cell. Flotation cells, such as the Jameson Cells, are smarter designs that improve bubble/particle collection, bubble/pulp separation efficiency and operate with high froth recovery rather than simply getting bigger. The Jameson Cell was designed on the principal of improving the collection efficiency of fine particles by separating the contact zone from the separation zone and having the bubbles generated by the plunging jet shearing and entraining air. This means the method of bubble generation is not impacted by the wear of mechanical equipment as it the case in other flotation devices. Jameson Cells make bubbles less than 600 micron in size under most operating conditions (Ding, 2016).

Jan 1, 2019

By Ross Dimmock

The productivity of a mine has the same goals as the quest to complete a tunnel project both safely and within time. A key aspect to achieving this goal is to excavate and support the working face as quickly as possible, allowing early re-entry to start construction of the next advance in safety. As with tunnels, the use of high performance wet-mix sprayed concrete has increased in mines dramatically over the last few years, and year on year has seen a stepwise increase in shotcrete performance, particularly in the first few hours. Shotcrete early age strength development clearly offers mining teams enormous advantages by allowing early, safe re-entry to the face. This paper illustrates that in the hard rock tunnelling field, modern shotcrete approaches do not cause delays in re-entry, but allow a continuous construction cycle. Furthermore, the paper identifies the most suitable, up-to-date shotcrete admixture and equipment technology available to the mining community to permit early re-entry.

May 1, 2003

By Gordon. I. M., J. Blackshaw

"The wet part of the Hollinger mill is housed in two buildings, the grinding plant and the treatment plant. In the grinding plant there are four 7xl5 ball mills which grind the ore to 60 per cent through 200 mesh. There is also one 7xl5 ball mill which grinds table concentrate to 9 5 per cent through 200 mesh.The primary classifier overflow is pumped to the treatment plant where it passes over shaking tables, producing a concentrate and a tail. The concentrate pulp is pumped to the grinding plant for secondary grinding. The secondary classifier overflow is pumped back to the treatment plant where it is thickened in two 40xl 5 tray thickeners and agitated in four 20x24 mechanical agitators arranged in series of two (with 2 spares).The table tail pulp is thickened in nine primary 40xl5 tray thickeners (with 2 spares). The thickened table tail pulp and the concentrate agitator discharge pulp are mixed and pumped to four rows of 15x45 pachuca agitators, arranged in series of five tanks.The pachuca discharge pulp is divided. The smaller part goes to two rows of 3-step decantation using 40xl5 tray thickeners (with 2 spare rows). The larger part goes to six 14xl6 drum filters. The repulped primary filter cake and the thickened pulp discharged from the decantation rows are fed to eight 14xl6 drum filters. The secondary filter cake is mixed with water and pumped to the tailing line."

Jan 1, 1968

By P. K. Kaiser, F. Amann

"Rock mass characterization for deep underground construction and mining offers many challenges. This paper first describes some of the key challenges when characterizing highly stressed brittle rocks and then offers some guidance on how to arrive at reliable rock mass strength parameters for deep mining applications. Focus is placed on characterization for rock mass strength determination. It is illustrated how the common use of currently available rock mass characterization systems tend to underestimate the strength of rock at depth. Modifications to currently adopted approaches, i.e., the use of Geological Strength Index GSI for rock mass strength determination, are presented.INTRODUCTIONFor green fields projects, the first challenge of rock mass characterization stems from a lack of access to examine the rock mass at scales larger than typical core sizes (i.e., ~63mm in diameter) until late in the mine design when the flexibility for making changes is constrained. Hence, rock mass characterization often has to rely on information derived from boreholes alone (e.g., core, logs, etc.). This challenge is lessened when mines are expanded from existing operations. A second challenge is related to changing rock mass behaviour with increasing depth and stress. At depth, the rock is highly stressed, thus closer to failure, and often highly confined which leads to a higher interlocking with elevated strength but more brittleness. The goals of rock mass characterization are to be tailored to the technical goals of an investigation. For example, for cave engineering, the workflow includes the assessment of five key engineering aspects (Brown, 2007): Caveability; fragmentation; cave performance; extraction level stability; and mine construction (rock support). Each engineering aspect has to address specific engineering questions and each design component is influenced by different rock mass behaviour aspects and thus is dominated by different rock mass properties, e.g., the vulnerability to stress fracturing (spalling), the bulking characteristics for flow control and support selection, and the confining stress impact on pillar or support design. An effective rock mass characterization program, including logging, mapping and laboratory testing, thus has to collect and interpret features that are relevant for the above listed purposes. Some of the predominant factors are: block volume of defected and non-defected rock; spalling strength; tensile strength of defects; rock mass modulus; and rock mass strength parameters for application to low and high confinement design aspects."

Jan 1, 2015

By Ali Hashemi, Anna P. Perry

The PQ Deeps (PQD) is a production zone located at Newmont’s Musselwhite Mine in northern Ontario. Development started for the PQD in late 2017, and the first stopes were mined starting in early 2021. Unlike most historic longitudinal stoping of narrower orebodies at Musselwhite, the PQD is a wider orebody following the plunge of a fold hinge and is extracted primarily by transverse stoping. Some geotechnical challenges were experienced during early stoping efforts, necessitating design changes throughout late 2021 and early 2022 to optimize the stope design. This work describes the mining methods and design changes to transverse PQD stoping based on geotechnical lessons learned during early stoping efforts.

Jan 1, 2023

By L. Bichler, A. Siebert-Timmer

In this research, novel YSZ ceramics doped with 5 mol% Nd2O3 were manufactured via Spark Plasma Sintering (SPS) process. The sintered Nd2O3-YSZ ceramics were subjected to a static supercritical water environment at a temperature and pressure of 400 °C and 31 MPa, respectively. The weight loss and microstructure development of the sintered ceramic before and after exposure to supercritical water was studied. The results suggested that Nd2O3 addition significantly improved the degradation resistance of the YSZ ceramics. This was attributed to the improved phase stability of the 5 mol% Nd2O3-YSZ ceramics, since X-ray Diffraction (XRD) studies showed that the cubic stabilized matrix in these ceramics was retained after exposure to supercritical water. In comparison, pure YSZ ceramics exhibited a rapid degradation behavior as well as a phase change.

Jan 1, 2014

By Mary Jean Buchanan

The last twenty years have seen the advent of environmental concerns and sustainable development, and the industry has witnessed the rise of Environmental Management Systems and their registration through several international standardization systems such as EMAS and ISO 14001. Beyond EMS and ISO 14001, which new goal the mining industry should aim at. Life-cycle assessment (LCA), another tool from the Environmental Management System series, is also on the rise and currently the object of an international standard (ISO 14040:1997). Through LCA, it is possible to assess the environmental aspects and potential impacts associated with products and services, taking into account all the activities required for its fabrication, its use, its transportation and its disposal. How could LCA be applied to the mining industry ? Is the international market pressurizing on mining companies to supply an ?environmental ore?? What about the automobile industry and its use of LCA ? Will it influence the ferrous and non-ferrous metal industry, suppliers of raw materials ? This paper presents a review of possible applications of LCA for the mining industry as well as world trends.

May 1, 2001

By Md. Rashedul Islam

Magnetic data was collected from the Yeoju historical sites using the fluxgate gradiometer through six sites & several grids. We measured the vertical gradient by the FM256 Fluxgate gradiometer. The readings were logged every half meter. The obtained data were processed and treated to introduce a high quality magnetic image. The gradiometer results defined various positive and negative magnetic anomalies, which revealed the existence of several archaeological features of different shapes and sizes. The study of the process magnetic images give us a concept that the subsurface features are caved shape stone chamber tombs, burial mounds, deep room structure, Yeoju mausoleum, pagoda?s square foundation stones, walls etc. All these are superior work of early Goguryeo inheriting orthodox Silla style. So, the study area may have great archeological interest.

May 1, 2009

By J. F. Nie

Mechanical properties of precipitation hardenable magnesium alloys depend critically on the chemistry, structure, morphology, orientation and distribution of strengthening precipitates. It is therefore important to gain an improved understanding of these information and their correlations with mechanical properties. Our recent studies indicate that additions of 1-2 wt% of Zn to a Mg-6wt%Gd alloy result in a substantial enhancement in precipitation hardening and in creep resistance. If the strength and creep resistance of the resulting ternary alloy are to be further enhanced for commercial applications, then a detailed characterisation of the strengthening precipitates in these alloys is required. In the present study, the precipitates formed in a Mg-6Gd-1Zn-0.6Zr (wt%) alloy, peaked aged at 250°C, have been characterised in detail using transmission electron microscopy and 3-dimensional atom probe field-ion microscopy. It is found the peak-aged microstructure contains a dense and uniform distribution of precipitate plates that form on the basal plane of the matrix phase and are typically less than 1 nm in thickness. Detailed analyses of the structure and composition of these basal precipitate plates will be presented and discussed in the context of previous work on other Mg-RE¬Zn alloys of similar compositions.

Jan 1, 2006

By William M. Luff

"The Bathurst area has recorded mining production as early as 1837, although the bulk of the production has come in recent years. Production has been mainly from the well-known massive sulphide deposits, but vein, gossan, and a variety of other deposits have also been mined. This paper summarizes the history of the mined deposits, along with tonnages and grades produced. A number of ""firsts"" have been noted in the Bathurst area. The A Zone deposit, located in the Heath Steele area, was the first in the world discovered using airborne electromagnetic methods. Heap leaching of gold from the gossan zone at Caribou was the first operation of its kind in Canada. The Keymet mine was the first base metal (lead-zinc) mine in New Brunswick. For the past few years, the Brunswick No. 12 mine has been one of the largest zinc mines in the world.IntroductionThe Bathurst area (Fig. 1) first had mining production in 1837 when copper was mined from a deposit on the Nepisiquit river (MacKenzie, 1958). The majority of the production, however, has been in recent years from massive sulphide deposits, but there are also other significant operations. . Table 1 is a summary of Bathurst area mineral production, showing concentrator feed tonnages and mill feed grades. The table does not include peat deposits, sand and gravel, dimension stone or rock quarries. Figure I is a general geology map of the Bathurst area, indicating deposit locations. The deposits are divided into four categories: massive sulphide, vein, gossan and other. The deposits in each category are described in chronological order of exploitation."

Jan 1, 1995

By D. Magoon

The metals industry has enjoyed a resurgence in prices and demand for its commodities during the global surge in economic activity that began in 2005. This success has brought with it an unprecedented demand for professionals in all sectors of our economy. Nowhere is that more true than in the mining and metallurgy sectors. However, this welcome improvement follows on the heels of almost two decades of challenging markets for the mining and metallurgy. Our sector's protracted economic slump created a paucity of demand for professionals that had several consequences. Our industry came to be viewed as a low ?tech, uninteresting place to work. Low demand for professionals encouraged students to seek other career options. Reduced demand for graduates, coupled with diminished program funding by our sector, resulted in dramatic shrinkage in university mining and metallurgy programs. This paper explores the lessons to be learned from our recent economic history and discusses some strategies for addressing our image issue. Attracting and retaining good employees is also strongly influenced by a company's reputation and record as a good employer. This reality is very well illustrated by the findings of an international survey undertaken by Towers Perrin in 2005 of 86,000 employees of mid-sized and large companies in 16 countries. The key findings related to attracting and retaining employees are presented. These findings are also discussed in the context of their specific applicability to the mining and metallurgy industry.

Jan 1, 2007

By B. T. Lu, J. L. Luo, H. X. Guo

This paper investigated the synergistic effect in the slurry-erosion process of carbon steel. In line with the mechanisms of material loss, the synergism due to interaction of erosion and corrosion was divided into the corrosion enhanced by erosion and erosion enhanced by corrosion. The erosion-corrosion tests were conducted with A1045 steel in slurries containing silica sand. Experimental results showed that the rotating of the sample in corrosive media raised both OCP and corrosion rate, but the impingement of solid particles did not affect the corrosion current significantly. In the quiescent solutions, the Faraday's law gave a good prediction for the weight loss caused by corrosion but for rotating samples, the weight loss experimentally measured was virtually greater than that predicted by the Faraday's law, indicating that the corrosion-enhanced erosion could occur in corrosive fluids in absence of solid particles. A half-logarithm relationship was observed between the weight loss due to corrosion-enhanced erosion and the anodic current density.

Jan 1, 2004

By L. Gawlik

Since the beginning of the 20th century, coal has been the world?s main source of primary energy. In the last few decades, consumption of coal has gradually decreased in some European countries and elsewhere due to the introduction of other energy sources. Regardless, industry continues to use solid fuels for energy production despite of their association with carbon dioxide emissions (about 7 billion Mg). For global development going forward, it is important to estimate what level of energy consumption can be expected as far into the future as the next few decades. To answer this question, specialized global institutions such as the International Energy Agency, the World Energy Council, the World Coal Institute, the U.S. Energy Information Administration, the International Institute for Applied Systems Analysis, as well as oil companies (BP, Shell), conduct periodic forecasts of world energy consumption. The development of such forecasts is very complex because their reliability is influenced by many factors that are difficult to estimate, such as economic development, population growth, climate change, and public awareness. We are all aware that the global demand for electricity will rise significantly in the coming years as a result of anticipated population growth, industrial development, rising living standards, and the general development of civilization. The world?s mineable resources in 2010 were as follows: coal 665.6 million Mg, brown coal 195.4 billion Mg, oil 163 million Mg, and natural gas 185.5 billion m3. The annual global primary energy demand in 2008 was more than 12 billion toe (12,267 Mtoe). In 2006, electricity production in the world amounted to 18,921 TW?h. The structure of the primary energy mix in TW?h (2006) was as follows: coal 41.0%; natural gas 20.1%; nuclear fuel 14.8%; hydro energy 16.0%; liquid fuels 5.8%; and other renewable energy sources 2.3%. The European Union (EU) is one of the largest coal consumers in the world. In 2010, the EU-27 produced 396.1 million Mg of brown coal, and 132.9 million Mg of hard coal; 188 million Mg of coal was imported from outside the EU. The largest hard coal producers in the EU-27 are Poland, Great Britain, Germany, the Czech Republic, and Spain; major brown coal producers are Germany, Greece, Poland, the Czech Republic, and Hungary. For many years, the Polish energy sector has been based on domestic fuel sources ? hard coal and brown coal. The characteristic feature of the Polish balance of primary energy resources is a very high share of coal ? much higher than the world average. Pursuing the decarbonisation of the Polish economy may jeopardize Poland?s energy security, leading to a significant increase in electricity prices, which would hamper the country?s economic development. Price volatility and supply uncertainty are now the dominant features of the international markets for oil and natural gas. The high share of these fuels in meeting energy needs is the reason for unrest in many countries, including those in the EU. Under these circumstances, coal may become the stabilizing element of EU energy security.

Aug 1, 2013

By Amin Jafari

Macrosegregation has always been an important issue with the solidification processes, particularly in Direct-Chill Casting of Aluminum alloys, where uneven properties, surface and bulk defects and limitations in productivity can be arisen due to macrosegregation in the cast product. Following the global attempts to practically predict the macrosegregation, in the present work, a numerical model was developed based on an industrial scale DC casting process to simulate the solidification and macrosegregation in an Al-4.5%Cu billet. Interesting aspects of this investigation are concerned with an efficient numerical scheme to keep simplicity, consistency and desired physical resolution of the solidification phenomena together. In the mathematical model, coupled conservation equations of mass, momentum, energy and species were solved numerically using finite volume method. A different numerical scheme, called SIMTLE, was introduced to link the energy and species equations with the phase diagram of the alloy. Calculations were performed on an industrial case and obtained results were compared to available experimental data to assure the performance of the model. Different macrosegregation features were predicted and discussed on the solidifying Al-alloy billet.

Oct 1, 2011

By C. Gaubert, G. Bourassa

"The construction or rebuild process in the anode baking furnaces has been modeled with the software Rockwell Arena, in order to minimize the process cost and risk. The case study was focused on the sectional rebuild (""on the fly"") that needs a high coordination of the material inventory, the on-site personnel and the construction/production schedule. Multiple entities and resources were allocated for the different part of the process (in-furnace process, prefabrication, materials transportation, etc.). Logic flow charts and VBA macros were used to simulate the space utilization (including cranes utilization) and interaction with production. MS-Excel output files can show user-friendly results."

Jan 1, 2006

By J. R. Pacheco

Paranapanema group has decided to implement the business system SAP R/3 in all companies of the group in order to replace all current applications. This project has taken nine months to be completed. This paper describes the phases of this implementation, with focus on the Plant Maintenance component. In addition, it gives an idea of the effort required to implement SAP R/3 on an organization the size of Paranapanema group.

Jan 1, 2007

By C. F. Gleeson

"I HAVE BEEN ASSIGNED the pleasant task of adding a last word in way of summary to this session. I think that the trend set in having a geochemical session at the CIM Annual General Meeting is a good one and I hope it will continue so that members of the mining fraternity can get together on a regular basis and discuss geochemical problems peculiar to our Canadian scene. A series of interesting papers have been presented on what has been considered by many in the past as not only a problem area for geochemistry but even an impossible one. The papers should help dispel some of these fears. Lack of development of geochemical techniques in the Shield has been due to a variety of factors, many of which have been mentioned. However, I feel that one of the main reasons for this lack of development has been timidness on behalf of many people to get out and do the necessary work which helps produce answers to many of the questions asked. New developments and applications of geochemical methods in the Shield will not be done by the faint of heart but by those who have the curiosity, interest, imagination, drive, resources and, most of all, the intestinal fortitude to stick to it and not give up because results or conditions do not meet with preconceived notions. Another element that will be needed by those who will successfully apply the techniques and who will be responsible for new breakthroughs is the systematic approach to sampling and analysis and the integration of geochemical, geological and geophysical results. Erratic sampling patterns - a sample here and a sample there - generally lead to more problems than solutions."

Jan 1, 1971

By Michel Noël

This paper presents a partial compilation of adopted measures of waste rock dump closures at mine sites located in Canada and Alaska, where the climate includes cold winters. The paper also presents the selection process that was followed for some of those mine sites. Mining operations usually generate waste rock that can sometimes result in very large quantities. Additionally, the nature of the ore body and the host rock will often introduce environmental impacts. These impacts need to be managed not only during the operations but also in the long term. Mine closure plans consequently have to address the long term issues that sometimes require perpetual treatment. Closure planning often involves the evaluation of risks associated with environmental and financial liabilities. It needs to consider the science, some common definition of objectives, and there will be a need to manage resources and schedules. Closure planning is essentially an exercise in constrained decision making. A performance and risk based ranking matrix is often developed during this selection process to identify the preferred option(s). The case studies presented in this paper provides a few examples. The level of knowledge on acid rock drainage from waste rock dumps has increased considerably over the past decades. It did not necessarily increase the level of complexity of the adopted closure methods, as the selected closure methods are often kept simple. A common approach consists of stabilising the slopes of the waste rock dumps material by resloping and then covering the waste rock with a growth media to support vegetation. Such covers prevent direct contact of animals with the waste rock material, minimise erosion and reduce infiltration to various degrees. The inclusion of water treatment is obviously dependent on the water quality being released.

Nov 1, 2008

By K. Pienimäki

Boliden Harjavalta Oy has produced copper since 1945. The essential idea has always been continuous development of process efficiency and environmental friendliness by using the Best Available Techniques (BAT). The ongoing development step is to increase the production capacity up to 210 000 tpy of anode copper and 155 000 tpy of copper cathode. One of the focal issues in this action is modernization of the copper refinery to utilize permanent cathode technology. This paper describes the refinery project and the technology used in it.

Jan 1, 2007

By V. Pouyafar

In recent years semi-solid processing of steel alloys has gain more attention among researchers. Production of high quality complex steel parts with higher mechanical properties is the final goal for all these researches. A thorough understanding of the flow behavior of the metal under investigation is the key for a successful process design. The material used in this research is M2 tool steel. The experiments were performed using a Searl-type concentric cylindrical rheometer which is specially designed for high temperature rheological measurements up to 1500 ºC. The rheological techniques were consisted of continuous cooling experiments and isothermal holding and also shear rate step change experiments for different solid fractions. Based on the rheological data a single phase thixotropic model has been derived and adopted to the measured data. The state of the microstructure has been applied through a structural parameter. The model fits well with the experiments.

Oct 1, 2011