Search Documents

By Patrick Laflamme, Jean-François Boulanger

Les minerais de cuivre sulfurés, qui représentent 80% de la production mondiale de cuivre, imposent une étape de concentration des minéraux, premièrement pour atteindre une teneur en cuivre minimale qui permette le traitement pyrométallurgique, mais aussi pour limiter la présence d’élément pénalisants (délétères). Cette introduction offre un survol des principes, limites et pistes d’améliorations touchant la concentration des minéraux de cuivre.

May 2, 2024

By Tom Shumka

INTRODUCTION ?This bull gear inspection technique was developed to provide more accurate data and faster inspection times than current techniques used today. ?Eddy Current Array (ECA) is a non-destructive testing technique that provides the ability to electronically drive multiple eddy current coils, which are placed side by side in the same probe assembly. Each individual eddy current coil in the probe produces a signal relative to the phase and amplitude of the structure below it. ?This data is referenced to an encoded position and time and represented graphically as a C-scan image. Most conventional eddy current flaw detection techniques can be reproduced with ECA inspections; however, the remarkable advantages of ECA technology allow improved inspection capabilities and significant time-savings.

Oct 1, 2010

By Norm Clegg

The Plant Engineering and Maintenance Association of Canada PEMAC is a national, not-for-profit industry association for plant and facility maintenance, engineering and physical asset management in all industry sectors in Canada. Our mission is to provide professional development for our members and the profession in Canada

Feb 1, 2008

By X. Cao, B. S. Naik, D. L. Chen, P. Wanjara

AZ31B-H24 Mg alloy sheets with a thickness of 2 mm were friction stir lap welded (FSLWed) at two tool rotational rates of 1000 and 1500 rpm and two welding speeds of 10 and 20 mm/s. The tensile behavior of the FSLWed AZ31B-H24 Mg alloy was then evaluated at low (-40°C), room (25°C), and high (180°C) temperatures. It was observed that the failure load increased with decreasing tool rotational rate and increasing welding speed. The maximum failure load occurred at a tool rotational speed of 1000 rpm and a welding speed of 20 mm/s at all temperatures tested. It was also noticed that at the high test temperature, the samples failed along the sheet interface, i.e. shear fracture. At the low and room temperatures, the samples failed on the advancing side (AS) of the top sheet near the interface between thermo-mechanically affected zone (TMAZ) and stir zone (SZ). The different modes of fracture observed are associated with the hooking defect.

Jan 1, 2014

By Bo R. Arvidson

"New permanent magnetic alloys have recently opened up possibilities for development of unique mineral separators. These are now making several new applications feasible. In many cases where conventional electromagnetic-induced roll separators have traditionally been used, the new permanent magnetic roll separators may reduce both over-all capital costs and operation costs.The development of the next generation of extremely powerful permanent magnets, i.e. neodymium-iron alloys, is progressing rapidly and will affect the roll separator as well as another type of magnetic separator. Permanent Magnet Roll SeparatorDesign and FeaturesDiscs of permanent magnets interleaved with soft iron discs constitute the basic magnetic roll design (Fig. I). By enveloping the magnetic roll with a thin abrasive resistant belt (Fig. 2), even highly magnetic particles are removed.The first prototype roll utilizing the new magnets was shown to have approximately equal strength as induced magnetic roll (IMR) separators. Since the initial test roll, the new separator, called the PERMROLL® , has been made twice as strong with regard to magnetic force, that is, the magnetic flux density is determined to exceed 1.7 tesla (17 kilogauss), while the magnetic field gradient is more than twice the gradient than can be practically achieved with IMR."

Jan 1, 1985

By T. Rahimzadeh, C. W. Trueman, S. Farzaneh, S. V. Hoa, I. Abdalla

This paper presents the shielding effectiveness (SE) of woven continuous carbon/epoxy composite materials. The theoretical and physical concepts behind the experimental results are demonstrated in details. The influence of frequency, the overlapping angle between overlapped layers and the number of overlapped layers upon the EMI shielding of composite sheets are discussed. In this work, in particular, the epoxy layers are considered as dielectric apertures of the conducting carbon fiber slab for the interpretation of the experimental results. The experimental results, using ASTM standard D4935-89, indicate that the SE can reach values greater than 90 dB above 500 MHz.

Jan 1, 2006

By H. Gharahbagheri, S. Shafiei Zadeh, H. Hassan Nejad

Waste Electrical and Electronic Equipment (WEEE) is one of the fastest growing types of solid waste in the world, and often contains precious metals, especially gold. Gold processing and recovery from secondary materials, especially WEEE, have been under investigation for more than a decade now; however, a comprehensive review that illuminates the future path is missing in the literature. The aim of this short paper is to discuss the recent advances in gold processing and recovery from secondary electronic materials and why it has not yet become practical. The role of pyrometallurgical and hydrometallurgical methods, as well as their advantages and disadvantages will be discussed; however, the focus will be on Biosorption and recent advances.

Jan 1, 2014

By Marty Hudyma

Mining-induced seismicity and rockbursting is one of the primary risks in deep mines. Seismic data management software has been created to facilitate analysis of mining-induced seismicity. The Mine Seismicity Risk Analysis Program (MS-RAP) is a purpose built database with mine seismicity analysis tools. One of the primary features of MS-RAP is the creation of seismic hazard maps in quasi-real time. The seismic hazard maps identify areas that are more prone to large seismic events and rockbursts, allowing risk management measures to be focused on the areas of greatest risk. These maps allow mining engineers to be more proactive about identifying and managing seismic related geomechanics risks in mines.

Oct 1, 2009

By J. A. Drozdiak, A. Bamber

In this paper we examine, through pilot-scale testing, the possibility of operating a circuit comprised of two stages of HPGR comminution, followed by grinding through a horizontal stirred mill. In order to assess whether the novel circuit design could achieve the reduced energy requirements indicated in the literature, two more-established circuits, a cone crusher / ball mill and an HPGR / ball mill, were examined using a combination of testing and flowsheet simulation. The results showed that, based solely on the specific energy requirements for comminution, the HPGR / stirred mill circuit achieved a reduction of 9.2% and 16.7% over the HPGR / ball mill and cone crusher / ball mill circuits, respectively.

Jan 1, 2012

By A. L. MacAllister

"Keymet Mine lies on the Elmtree River 4 miles west of Petit Rocher and about 18 miles northwest of Bathurst, Gloucester County, New Brunswick. A good gravel road runs through the property.The deposit was discovered in 1880 when a vein 7 to 8 feet wide was re-ported. In 1883 the first shaft was sunk as part of an exploration program which was carried out sporadically until 1897, when the company dissolved. Activity on the property was intermittent until 1946 when the property was again staked and during the next year diamond drilling intersected the vein in several places. In December 1949 Coulee Lead and Zinc Mining Company optioned the property and held it until its sale to Keymet Mines Limited in June 1952. By July of the same year work had begun on a three-compartment shaft.Early development work was concentrated on the 150, 300 and 450 foot levels but the shaft has since been sunk to I,228 feet to allow for eight levels at intervals of 150 feet. Little lateral work has been done to date below the 600-foot level.The first mill constructed to treat the ore was to go into production in the spring of 1954, but was destroyed by fire. A second mill, having a capacity of 200 to 300 tons a day, was officially opened October 25th, 1954. Present shipments are zinc and copper-lead-silver concentrates.The rocks of the area are shale, conglomerate, limestone, and quartzite with minor interbedded volcanic rocks, all probably of Silurian age. Small plugs of Devonian acidic intrusions occur 3 miles east and about 5 miles northwest of the mine. Minor dykes of both acidic and basic rocks occur on the mine property. In many of the fine-grained sedimentary rocks the more brittle laminre have been brecciated and give the rock the appearance of an argillaceous conglomerate."

Jan 1, 1949

By Peter Van-De-Velde

"The results of applying Japanese pumping technology to North American reclamation projects will be discussed.IntroductionEconomic high-density mineral reclamation and subsequent transportation of solids through a pipeline presents many formidable engineering problems.In North America where space has rarely been a facto r, industry has generally relied upon the traditional dumping of material into various waste ponds, etc . In Japan, where confined geographies and stringent environmental regulations are enforced, alternative solutions for disposal or reprocessing of waste material had to be found.High-density mineral reclamation system designed by theoretical formulas is almost impossible because solids composition, i.e. concentration, velocity, moisture content, solid size, etc. can only be controlled within a broad pumping range.Traditionally this has restricted dredging of material to relatively dilute slurries whereas it is usually preferred to reduce water usage with its associated power and reclamation costs to a minimum and reclaim as high a concentration as possible.At Toyo Pumps North America we recognized these pumping limitations and began to develop and manufacture a range of standard and auxiliary equipment that would exceed these technical restrictions."

Jan 1, 1985

By M. Moghadami

Design and construction of underground openings are associated with many uncertainties with regard to input data. In the construction process of underground openings various levels of risks exist and these affect the safety and profitability of the project. The development of underground openings can be broadly categorized into three major phases of data collection, design, and construction. A significant level of uncertainty is associated with some of the key parameters involved in the aforementioned development phases. Moreover, it is very difficult to evaluate and quantify the effects of uncertainties on the underground project construction process. Additionally, the interactions between important risk elements are typically not well understood. The intention of this study is to develop a general risk model for underground opening projects located in soils and weak rock masses. The goal of the research is to identify and quantify important geotechnical risk elements. Moreover, a weighting procedure will be proposed for the identified risk elements. Finally, all important risk elements will be assembled into a general model with emphasis on geotechnical parameters. The final objective of this study is to apply the proposed model to a real underground project scenario and verify it for actual field conditions. The proposed model, once calibrated properly, will provide a useful support tool for the decision making process.

Aug 1, 2013

By S. M. Bulatovic, D. M. Wyslouzil

"This paper presents the results of a study of the effect of flowsheet configurations on metallurgical results and describes a general method for developing and optimizing flowsheets used in the treatment of massive sulphide ores. The flowsheet configuration can have a significant effect on recovery and selectivity between valuable minerals and gangue minerals. Placing of intermediate products within the flowsheet, positioning of various pretreatment units, such as conditioners or regrinding mills, and the ability of the flowsheet to cope with wide swings in the feed grade and composition are the major parameters that determine the optimum flowsheet configuration. The complexity of the flowsheet is largely a function of the ore itself and of the number of final, marketable products that have to be recovered from the ore. INTRODUCTIONTechnological ExpansionThe trend of past decades has been towards larger equipment and a better understanding of the chemistry of the flotation process. Despite appreciable progress in these areas little attention was given to the study of the actual configuration of the flowsheet, although the arrangement of the flotation equipment significantly affects the overall performance of the circuit."

Jan 1, 1989

By Peter S. Jack

"IntroductionTHE ORES treated at the concentrator of the Britannia Mining and Smelting Company, Limited, Britannia Beach, B.C., have always contained some lead, but it was not until 1950 that the combination of lead headings and lead price was such that recovery of this metal at Britannia became worthwhile. In that year, with the mining of a new orebody, the lead in the mill feed was raised from 0.07 per cent to 0.15 per cent. Chalcopyrite, sphalerite, and pyrite concentrates are produced by flotation at Britannia, •and 95 per cent of the lead in the mill feed reports with the chalcopyrite concentrate, so that the rise in lead headings was reflected almost wholly in the lead content of the copper concentrate. In 1950, investigation was started to determine if some of this lead could be recovered economically."

Jan 1, 1953

By M. Leijd, K. S. Forrester, M. Saxon, M. Oczlon

This paper provides an introduction to wet high intensity magnetic separation (WHIMS) and its successful application to the beneficiation of rare earth element (REE) enriched eudialyte. The analysis includes an in-depth reporting of the deportment of key elements as well as a statistical interpretation of the relative importance of operational parameters including magnetic field intensity, flow velocity, and matrix loading density. Conclusions are drawn on the relative success of the technology, potential areas for process improvement, and the research direction that continues to be investigated. Three original equipment manufacturer (OEM) technologies were subjected to a series of screening and characterization tests to identify the optimal operating parameter set to magnetically beneficiate eudialyte from Norra Kärr, Sweden. Upon the completion of the characterization test it was apparent that the Metso HGMS technology was superior with respect to REE recovery and gangue rejection for the Norra Kärr composite. The Metso HGMS was then subjected to a series of verification tests to confirm the repeatability and reproducibility of the system.

Jan 1, 2014

By Malcolm Scoble

School Values ?? Each other; ?? Students, & helping them develop intellectually, personally & professionally; ?? Freedom to pursue educational & research opportunities; ?? Home-work-life balance; ?? The geographic-business community in which we operate ; ?? The pursuit of excellence; ?? Our contribution to society; ?? Creativity & innovation; ?? Teamwork & collaboration; ?? Career development, achievement & reward.

May 1, 2008

By Samantha A. Beeson, Colin Poole

"A selective flocculation-floe flotation technique is already in use in the Canadian potash industry for the removal of water-insoluble slimes, but the process is currently limited in its application and reagent consumption is high. The work described in this paper details investigations into the separation of sylvite and halite from water-insoluble slimes by selective flocculation utilising other commercially available polymers.Preliminary flocculation performance tests were undertaken on pure sylvite, halite and water-insoluble minerals to establish the importance of a number of experimental parameters. The data from these single mineral tests was then used to establish optimum parameters for the separation of sylvite and halite from a synthetic mixture similar in composition to a typical potash ore. Under optimum conditions, separation was achieved with high recoveries using dispersant and flocculant dosages significantly lower than those currently used in plant practice.IntroductionAlthough solar evaporation and solution mining are used in some operations, most potash is extracted by conventional underground techniques and is then processed by froth flotation, in order to separate the valuable sylvite (KCI) from halite (NaCl) and water-insoluble gangue minerals. Flotation is usually preceded by a desliming stage to remove water-insoluble fines, but this also results in high potash losses and affects process brine requirements. To overcome these problems, one plant operated by Cominco in Saskatchewan uses a selective flocculation -floe flotation process (Banks, 1979/1980), in which a polyacrylamide flocculant is added to produce floes of water-insoluble material with minimal incorporation of halides. A collector is then added to render the floes hydrophobic and suitable for removal by froth flotation.A number of workers have also investigated the use of selective flocculation in potash processing, but these too have been concerned with developments in the removal of water-insoluble slimes (Williams, 1960; Brogiotti et al, 1974; Chan et al, 1986; Thompson et al, 1979; etc.). This paper provides results of novel investigations into the selective flocculation of sylvite and halite from water-insoluble minerals and discusses the possible mechanisms involved."

Jan 1, 1995

By Ron Hatch, M. K. Witte

"INTRODUCTIONThe proper selection of carbon for a gold carbon in pulp (CIP) circuit involves careful evaluation of several physical, chemical and economic factors. A series of evaluations are required to maximize gold recovery at the lowest capital and operating costs, whether the carbon is selected for an existing gold mill circuit or a new mill under design.Although evaluation may proceed through various stages, it is the intent of this paper to outline some of the preliminary testwork that should be carried out to screen potential carbons for a particular application.An examination of the specification sheets supplied by the various carbon manufacturers may indicate some desirable properties on which to make cursory selection. This exercise by itself will not provide the basic data needed for selecting the best carbon for a particular ore pulp and metallurgical circuit. The necessity of further metallurgical evaluation is indicated by the fact that different carbons perform differently depending on the physical and chemical nature of the leach pulp. In the case of an existing mill, actual leach slurries using mill water are available and should be used for testwork. In the case of new mills, leach pulps must be prepared to simulate the proposed circuit.Five coconut shell activated carbons were obtained from various suppliers, all reported to be 6 x 16 mesh carbons recommended for CIP circuits. A metallurgical evaluation was made utilizing two leach pulps with significantly different characteristics. This paper describes the test procedures utilized and the results obtained from the testwork."

Jan 1, 1985

By M. Rafati

In this investigation, the effects of T4 and T6 heat treatments of AZ91 magnesium cast alloy have been studied. The effects of different microstructural details such as morphology, size and distribution of precipitates and their influence on fracture mechanisms were investigated by optical and scanning electron microscopy. The mechanical strength of the alloy after T6 treatment was found to increase in comparison to the T4 treatment, due to the formation of discontinuous precipitates in the grain boundaries. Precipitation in this alloy occurs in two ways: continuous precipitation, which nucleates and grows inside the grains, and discontinuous precipitation, which forms at the grain boundaries. During ageing, the length of the continuous precipitates increases, and, hence, interprecipitate distance decreases. The formation of discontinuous precipitates causes initiation and propagation of cracks at and the weakening of the grain boundaries. This is the principal reason for the reduction of the ultimate tensile strength in T6 heat treatment in comparison to the T4 condition.

Jan 1, 2006

By Anthony P. Makuch

Dynatec Corporation is an integrated mining services company, providing mine development, operations management, engineering, drilling and metallurgical services to the North American mining industry. Dynatec was the contract operator of the Ken Snyder Mine in Midas, Nevada from start of production in January 1999 to September 2001. This paper summarizes Dynatec?s experience and approach to the use of longhole stoping methods for mining to widths of 1.3 to 2 metres in a steeply dipping narrow vein orebody.

Oct 1, 2001