Search Documents

By J. A. Finch, A. M. Elmahdy

Blending frothers is becoming common in flotation practice apparently enhancing performance. However, there have been no studies to understand the blend mechanism. In this paper, the effect of two frother blends ofF150 (polyglycol) with MIBC or pentanol (both alcohols) on bubble size, gas holdup and froth height is reported. The blends focused on a small addition of the polyglycol to the alcohols as base frother. The tests showed that the bubble size at blend concentration below the critical coalescence concentration (CCC) of the base frother was decreased but was significantly larger above the base CCC. Froth build-up showed a strong synergistic effect.

Jan 1, 2009

By C. Graham

Mechanisation has been a predominant theme of the past 50 years in the mining industry, particularly underground mining. As the level of technology employed has increased, the anticipated productivity gains have not been realised and the differences are not explained by the demand for higher standards of safety and security. Now, mining costs are so high and productivity so low that the resultant return on investment for many Canadian operations has fallen to levels considered unacceptable in a competitive capital market. Simply continuing technological development cannot reverse this trend and its financial implications. The focus on technological development has distracted us from some basic truths. Systems that are more complex are more likely to fail and cost-effective processes depend on the continuity of productive activity and the flow of material. When putting these facts together, it becomes clear that in a system that has fixed external conditions, the single most crucial issue is the effective management of the operational cycle. By its nature, technology focuses our attention on what gets done and how it gets done, while the crucial issue is the increasingly longer periods in the operational cycle when nothing productive is being done. What is required is to match the level of technological complexity to the fixed system conditions, which are virtually unchangeable. This paper looks at the overall system and objectives and attempts to present an appropriate level of technology for the Canadian mining industry, now and in the foreseeable future.

May 1, 2004

By Donald F. MacDonald

WE are living in a mineral and technological civilization. The Encyclopedia Britannica defines civilization as follows: "It is the final test of a progressive civilization that a given effort shall produce a larger modicum of average individual comfort, and the pursuit of this ideal has been from first to last the impelling force which drives civilization onward". This "individual comfort" demands labour-saving machines and devices such as motor cars, radios, and thousands of other inventions, most of which require minerals and metals in vast quantity for their manufacture. In fact, more minerals and fuels have been used in the last third of a century than in all previous world history. Since 1800, the world's production of metals has increased more than a hundred fold (1). Scientific discovery is now advancing on a wide front, thanks to the research work that is being carried on in progressive countries. The world's work is now being done with very much less human drudgery than in the past. We do not have to toil for our living as our ancestors did, even if we follow their occupations. The average man has had many years added to his life-span, but, apparently, little to his spiritual stature and less to his common sense.

Jan 1, 1939

By J. Holder

"A key barrier to vertical mineshaft construction is the construction access required for workers. A suspended work stage is used to provide this access for the mechanical, electrical and structural applications and other tasks. Work stage design is complicated considering the numerous types of construction activities that are executed simultaneously, the confined environment in which the work stage operates, the significant corrosion attack that is present, the weight limitations imposed by the mechanical hoist systems, and the risks associated with worker safety. Also complicating the design, these structures and their construction environment can vary with time. Hence, they can be described as 4D structures. The author has discovered significant synergies and advantages with integrating engineering design with detailed three-dimensional (3D) fabrication design. The significant reduction of minor design errors needing field correction will be underscored. The tender process is also accelerated since the design output is fabrication shop drawings including a detailed quantity takeoff output which lists each component required and its specific quantity. The paper presented will document the numerous advantages to the project using this approach. INTRODUCTION A key barrier to vertical mineshaft construction lies in the access for the workers to execute the construction. Suspended work stages are used to provide this access for the mechanical, electrical and structural applications as well as other tasks. The design of such work stages is complicated considering the numerous types of construction functions that need to be executed simultaneously, the confined environment in which it operates , the significant corrosion attack that is present, the weight limitation imposed by the mechanical systems for suspension, and the risks associated with worker safety. Also complicating the design, these structures and their construction environments can vary with time. They can be described as 4D structures with the fourth dimension being time. This design is a time consuming process. The post tender award is meticulous and requires strong teamwork between the steel fabricator and the consulting engineer. This teamwork may or may not be present and is dependant on the experience and relationship the team members have working together as well as other factors."

Jan 1, 2019

By DALE MacGREGOR, VERA TUREK

The Blue Mountain nepheline syenite deposit has been the subject of several detailed studies. It has been variously referred to as an intrusive stock, a metasomatic deposit, an intrusive sill and a metamorphic-metasomatic body. The body is divided into six mineralogical zones, the first five being based on the characterizing accessory mineral; muscovite, muscovitemagnetite, biotite-muscovite, biotite, hornblende and pink syenite. Mining currently takes place only in the biotite zone. Foliation is particularly prominent in the central (hornblende) zone and near the margins of the nepheline syenite. Majic bodies within the nepheline syenite may represent basic rocks that have been less altered by metasomatism, metamorphosed basic dykes or sloped blocks of metasediments. The most prominent structural features are the northeast-trending folds that have been modified by later north west-trending folds.

Jan 1, 1984

Kahama Mining Corporation Limited (KMCL), a wholly owned subsidiary of Barrick Gold Corporation, operates the Bulyanhulu gold mine. The operation has been in commercial production since April 2001 and is the first modern underground mine to be developed on the Lake Victoria goldfield in Tanzania. Bulyanhulu is located in a major mineralised system along an emerging gold trend. This area, the Lake Victoria Greenstone belt, has been the focus of significant exploration and development programs since 1994, with over 34 million ounces of gold having been discovered and four new mines commissioned. The Bulyanhulu project has accounted for just over a third of the gold resources discovered during this period. From an initial exploration program, which outlined a resource of 1.37 million ounces of gold, Bulyanhulu now hosts a reserve of some 12 million ounces in a resource base, the limits of which are, as yet, undefined. The Bulyanhulu property is located approximately 56 km south of Lake Victoria, in northwestern Tanzania, eastern Africa. A Mining Licence issued by the Government of Tanzania on July 23, 1999 grants to KMCL the exclusive right to mine a concession area covering 51.48 km2. The property is reached via a 75-km road from the main road to Dar es Salaam. The nearest towns are Mwanza to the north on Lake Victoria, 155 km by road and ferry, Kahama, 86 km by road to the south and Isaka, 126 km by road. Isaka is on the rail line between Mwanza and Dar es Salaam and has facilities to receive heavy equipment, and a fuel depot. A gravel airstrip, 1,700 m long has been constructed at the property.

May 1, 2003

By G. C. Laurence

"This paper discusses the hazards and extensive precautions taken in Canadian uranium mines, concentrating plants and processing plants. It also outlines Canadian policy regarding the control of the sale and distribution of uranium and other nuclear materials.OVER THIRTY YEARS AGO, I spoke to The Canadian Institute of Mining and Metallurgy here in Montreal about radioactivity and its dangers. I must have made quite an impression thirty odd years ago, because now you have asked me to do it again. Of course, the picture has changed. Then they were mining uranium ore, recovering the radium from it and throwing away the uranium. Now they are still mining uranium ore, but are throwing the radium out on the tailings dumps. Thirty years ago, most people did not know what ""radioactivity"" meant. Nowadays, they have beard that it is dangerous, and some of them, recently, be-came worried about the radium in the tailings dumps and what becomes of it."

Jan 1, 1969

By S. M. Moon

Today, underground exploration is spotlighted as an infinitely developable area. For this purpose, many tunneling technologies were created. And until this very day, many techniques are being developed for more efficient underground movement. Although previous technologies have been developed and now being used in various forms like TMB, struck propulsion method and hydraulic propulsion method, it is hard to find a robot type exploring in small scale. But development of small scale underground exploration robot is a promising research subject for its usage in examination of soil, mineral, and subterranean resources, investigation of hazardous regions, and the military. So we developed a robot that can dig and move underground, inspired from the motion of earthworm and mole cricket. Earthworm and mole cricket dig the soil in the front and draw it off backward, so that they can move forward. We developed a mechanism that uses 2 rotating solid of revolution (bits) for pulverizing the firmly united soil in the front and put it inside the body. The bits rotate in the opposite direction of each other. While moving forward, the soil in the front moves along the spiral on the bit and is saved inside the body. The soil saved inside is taken out through an outlet in the back by a ventilation system. The ventilation system on the ground blows through a hosepipe connected to inner part of the robot and the air blows off the soil. The moving mechanism of exploring underground can be classified into 2 parts. One is to fix the blade link on the soil in a form of 4-bar link. The other one is to move forward rotating the whole link. When the blade link system for movement rotates a certain degree, one blade link is fixed, while the other one is folded in. When 2 blade links of different length rotate as it is, different torque is applied on each link. By the law of action and reaction, the link that has larger torque leads the rotation and movement.

Aug 1, 2013

By J. F. Vynne

ABSTRACT This paper examines several of the systems and processes that have been developed over the past few years and are now being utilized by major mining companies on draglines in North America, Australia and South Africa. These technologies include production monitors and reporting systems, GPS navigation systems, structural integrity monitoring systems, structural analysis studies to increase the dragline rated suspended loads (RSLs) and inspection and response strategies. The use of these technologies provides significant increases in dragline production and reduces maintenance costs, downtime and the chance of a catastrophic failure.

Jan 1, 2010

By J. Chlan

"Dryer DescriptionProctor and Schwartz Continuous Conveyor DryerThe Proctor and Schwartz Continuous Conveyor Dryer has been in operation since July 1958, and comprises six unit• - an 8• wide single conveyor with roller extruder, insulated housing, type 304 stainless steel circulating and exhaust fall system, steam heating coils, temperature controls and discharge crusher rolls. Entire dryer dimensions are 52’ x 12'0""weighing 53,000 lbs,Extruder rolls - setting is 1/8"" (Drive 3 HP 1800 RPM) clearance off the extruder screen.Conveyor - consists of 151 interlocking pans, measuring 8"" x 8' (2 HP 1200 RPM) One Exhaust Fan (5HP - 900 RPM)Steam Coils -- l"" steel pipe - with steel fins -- each coil measures 16' 2’’- 64 coils in the No, 1 Compartment- 64 coils in the No, 2 CompartmentDryer OperationThe yellowcake slurry at 28% solids is pumped to an 81 x 8' Peterson Filter. The filter media presently being used is a Neotex 4372 blanket, being 100% staple fibre nylon, 12 oz per square yard with air porosity of 9 CFM's. The cake discharge at 45 - 50% moisture falls into the roller extruder. Extrusions are formed by forcing the material by rolls through a perforated plate moving back and forth and depositing the spaghetti-like extrusion on onto the dryer-conveyor.The conveyor now carries the extruded material through the heating chamber•, The feed end of the dryer will be referred to as No. 1 Compartment, with temperature control set at 280""F. The circulating fans take the hot air off the coils and circulate the heated air through the perforated openings in the dryer conveyor pane, After passing through the set of steam coils and circulating fan in No, 1 Compartment, the material then goes through No, 2 Compartment where the temperature is set at 305'F, Final material then discharges through a set of crusher rolls set at ~"". Moisture of final dried product runs at less than 2%.The dryer conveyor load is usually run to a 3"" - 4"" depth load. Conveyor speed at approximately 90 minutes for load to pass through. Load onto the conveyor is controlled by boot level and speed of the 8' x 8' filter. The dryer steam coils are water-washed twice a month."

Jan 1, 1972

By Victor A. Sowa

"Abstract - In 1938, a body of goethite and hematite was discovered beneath Steep Rock Lake near Atikokan, northwestern Ontario. This was at the time the largest and richest undeveloped iron ore body in North America. Mining began in 1944, fast-tracked by the needs of World War II, and through 1979 produced 79 Mt of 56.5% Fe. Production required the diversion of the Seine River, draining of Steep Rock Lake, building of a railroad, and a 25-fold increase of the local population. The mining project, at the time, was the largest project of its type undertaken in Canada. The current concepts of sustainable mine development and mine closures have advanced considerably since the period of operation and closure of the Steep Rock mines, and those operations would probably not have met current expectations of sustainability. However, some of the post-closure aspects of the mines provide illustrations of components of sustainability, which could form part of a basis for a post-mining sustainable land use plan. It is concluded that some of these components were successful in meeting current expectations of sustainable use, and although some aspects are unique to the circumstances at the Steep Rock mines, others could be applicable at other mine sites."

Jan 1, 2003

By Ahmad Abdollahi

Many factors affect mechanical properties of hypoeutectic Al-Si alloys. As examples the presence of impurities such as Mn and Fe due to the formation of intermetallic phases, additions of small amounts of alkaline earth metals and cooling rate in consideration of Si formation, they all have an impact on mechanical properties of hypoeutectic Al-Si alloys. In this investigation, the effect of Fe content into the specification range of A357 alloy, the addition of different modifiers consisting of Na, Sr and Ca for the alloy of A356 and different mounting techniques for separately cast test coupons of hypoeutectic Al-Si alloys using the lost wax method were studied. The results showed that using material with lower Fe content and addition of modifiers improve mechanical properties. Also different mounting techniques resulted in different mechanical properties.

Jan 1, 2004

By R. Tessier, R. Grant, C. Bazin

"Brunswick Mining has investigated grinding media optimization for the purpose of improving the flotation feed and regrind product size distributions to enhance metal recoveries. The paper presents findings in the on-going testing of various sizes and shapes of grinding media. Breakage rates are used as an aid to assess the effect of grinding media. Results of empirical and phenomenological analyses demonstrate the importance of adequate selection of media sizes on the milling operation.INTRODUCTIONBrunswick Mining and Smelting operates one of the world's largest lead and zinc mine near Bathurst, New-Brunswick. The No. 12 ore body is an extremely fine grained volcanogenic massive lead, zinc, copper, silver, iron sulphide body between two metamorphosed sedimentary and felsic volcanic rock units. Pyrite content is about 60% with 20% non-sulphide minerals, mainly silica and chlorite. The operation is currently processing 10,500 tonnes of ore per day in conventional crushing, grinding, differential flotation and dewatering circuits. Details on the circuit can be found elsewhere (e.g. Hendriks and Ounpuu, 1985; Grant et al., 1991).The mill has operated for more than 25 years and despite the past milling experience, there has been much disagreement as to the required grind size. Since 1964, fineness of the flotation feed ranged from 60% to 80% passing 400 mesh (37µm) and averaged slightly over 71%in1992. Results from mineralogical analysis (Petruk and Schnarr,1981; Coleman, 1988), Brunswick metallurgical laboratory (Grant et al., 1991; Shannon et al., 1992) and Lakefield pilot plant tests (Hendriks, 1984; Hendriks and Ounpuu, 1985) clearly indicate that improved metal recoveries can be achieved by an increase in the fineness of grind, and more specifically by maximizing the amount of material in the 15-25µm range."

Jan 1, 1993

By A. Farzanegan, D. A. Lowther, A. R. Laplante

"Off-line optimization studies are often necessary to improve the efficiency of grinding circuits. These studies are primarily based on the mathematical modelling of processing units (e.g., ball mills and hydrocyclones) and computer simulations. To complete an optimization task, process engineers must possess skills and knowledge of different subtasks involved in such efforts, e.g., plant audit, laboratory tests, and data analysis. Such know-how can be in part provided by Knowledge-Based Systems (KBSs). One such system, being developed in C Language Integrated Production System (CLIPS), is presented here, with focus on the estimation of ball mill selection functions for the purpose of both diagnostic and simulation, and its use for the optimization of ball size. Some of the interpretation and diagnostic rules will be presented, as well as grinding kinetics and classification data likely to fire them.IntroductionSince the late eighties there has been a growing trend in applying Knowledge-Based Systems (KBSs) to mineral processing [Meech 1990, Bearman and Milne 1992). Table l lists some KBS (often referred to as expert systems) applications that have been used mainly as tools for improving on-line monitoring and control of grinding circuits. However, there has been fewer attempts to add the symbolic processing powers of KBSs to conventional off-line grinding simulators. Figure 1 shows a relatively standard procedure to perform an off-line optimization study [Napier-Munn and Lynch 1992]. In brief, a typical program includes taking representative samples from a number of streams, running laboratory tests on collected samples, estimating model parameters which describe physical processing units (e.g. ball mills and hydrocyclones) validating model predictions and using models for simulation trials. One inevitably needs to be familiar with concepts of process modelling and simulation as well as various computer programs to be able to complete all steps of the study. Much of this ""expertise"" can be captured by KBSs, given their inherent capabilities for symbolic knowledge representation and manipulation."

Jan 1, 1997

By John S. Stevenson

The Twin ''J' mine is on mount Sicker; 8 miles by road northwest from Duncan; on Vancouver island. It includes the old Lenora; Tyee; and Richard III mines; formerly under separate ownership but now under the single ownership of Twin "J' Mines; Limited.

Jan 1, 1954

By Rodrigo A. Marinho

Erratic high grade values are as common in Nature as they are a source of problems for resource estimators. In some highly erratic metal deposits, less than 2% of the drilling samples can represent more than 10% of the total metal in the blocks and they are associated with a high risk level. There is a risk of local overestimation but also of global overestimation, with the high grades being projected over too large a volume. Capping or restriction of these outliers control is being widely used in the industry and commonly applied in resource estimation for the last three decades. The primary purpose of this paper is to present and describe the most applied methodologies for restricting the extrapolation of high grade samples and discuss the results based on a theoretical simulated model. Additionally, this paper demonstrates the economical impact associated with the high-grade and the project risk profile associated with each method.

Oct 1, 2009

By M. Carvalho

The primary motivation underlying the proposal of polygeneration systems for mine sites is to increase the efficient use of natural resources by combining different technologies and energy resources while satisfying energy service demands. For many mineral producers, particularly in Canada?s mining extremes of climate and depth, energy in support of mineral production can be the second largest cost centre after labour. A generic methodology is proposed for the design of energy supply systems in mine sites, based on a search for the minimum discounted cost of energy supplied for all feasible different plant configurations. These configurations can be represented within a connectivity matrix which corresponds to a network representation. A Mixed Integer Programming formulation is set out for the multiperiod synthesis and operational planning problem. This is characterized by i) binary variables for the selection of technologies, ii) integer variables for the determination of the number of units installed, and iii) by continuous variables for the representation of energy and economic flows. Through the integration of particular energy supply strategies matching specific mine circumstances (on-grid, remote, degree days, etc) and consideration of technologies that improve energy efficiency, hitherto not considered new technologies and demand management systems or new perspectives on optimal mine site energy supply can be investigated. Some of these investigations identify the economic conditions through which biomass energy feedstocks should be used, for direct heat production, for gasification and providing for Fischer-Tropsch syndiesel manufacture. As well as integrating demand from mobile diesel-fuelled plant into an optimization procedure that hitherto has only been considered for static energy production and consumption plant, this analysis shows how the techniques can be used to explore economic conditions of threshold prices for biomass (purpose-grown biomass and peat are considered herein) and trucked-in diesel. The methodology also allows for electricity and syngas storage and diesel and biomass bunkering. Within the paper the energy demands for a remote, open pit mining operation located in Northern Ontario are considered as a case study to illustrate the technique and investigations. As expected, for mines close to electricity, natural gas, and diesel distribution infrastructures, the optimal choice is to connect. When a constraint is applied specifying that connection is not possible, as would be for the case exemplified, the optimal choice includes some of the more exotic options for mine site energy supply.

Aug 1, 2013

By D. F. Sherwin

"THE AREA which is described in this paper (Fig. 1) includes the continental margin of eastern Canada extending from the Gulf of Maine to the north edge of the Grand Banks, which, including the continental shelf, slope and rise, comprises an area of about 600,000 square miles. The paper is intended to give a background of the geological setting of this region in the context of its ultimate potential for oil and gas reserves in close proximity to the Nova Scotia energy market.HISTORY OF EXPLORATIONThe history of geological exploration of this area really began in 1878, when U.S. fishing boats brought back samples of rock recovered in trawls from their expeditions to the long-famous fishing banks off Canada's East Coast. Tertiary and Cretaceous fossils recovered from these samples indicated that the eastern Canadian continental shelf was actually the submerged northern extension of the Atlantic Coastal Plain."

Jan 1, 1972

By Martin Irving

Adding Value to Canadian Diamonds - A Changing Diamond Industry - Diamond Mining - Diamond Manufacturing - Diamond Jewellery Markets - NWT Diamonds Changing Diamond Industry - De Beers ? privatization - Oppenheimers (45%), Anglo-American (45%), Botswana (10%) ? going retail - LVMH joint venture - New Players ? jurisdictions - Canada ? companies - BHP-Billiton - Aber Diamonds

May 1, 2002

By O. Kodym

The paper has focused on possibilities of interconnecting information sources concerning monitoring & control of mining industry technical processes (TP), and the related safety hazards. The key issue is the comprehensiveness of the information presented to users. Information can be presented by virtual reality means, when the seemingly true presentation of the production process scene along with user friendly presentation of related information is available. The user in its role of a process supervisor is not only a mere scene observer but, thanks to the interactive functions of virtual environment, he participates in the scene of his control. As such his control and management abilities increase because he can absorb, more easily understand and asses the information provided.

Aug 1, 2013