Search Documents

By Moe Momayez

Shotcrete is a practical and economical support system in many Canadian underground mines. Although shotcrete technology has gained acceptance in the mining industry, there are some problems that have emerged with respect to quality assessment and thickness measurement of the liner. This paper presents recent tests performed with a miniature seismic reflection device developed primarily for thickness measurement of this heterogeneous liner. Work was performed on site in an underground mine in Ontario, Canada. This paper also presents the results from laboratory tests performed on fibre reinforced and non-reinforced shotcrete panels that were used to assess the P-wave velocity in both materials. The results of these tests were used in a second on site investigation. The NDT thickness measurements showed good agreement with direct thickness measurement such as coring.

May 1, 2001

By Antônio Peres, Rogério Guimaraes, Lauro Takata, Harold Wyslouzil

"Serrana’s concentrator, in Araxii, has capacity of producing approximately 800,000 tomes of phosphate rock per year, with a P205 grade of 36%, from ores grading between 13% and 14% P205. The annual mining rate is around 3.5 Mt and the apatite is concentrated according to the following sequence: crushing, grinding, desliming, flotation and low and high intensity magnetic separations.Two industrial flotation columns (3.0 m x 4.5 m x 14.5 m) were commissioned in 1993 as a replacement for circuits of barite and apatite fines flotation. In 1994, four additional flotation columns of the same dimensions were put into operation, replacing 42 Wemco mechanical cells (300 ft3 each), in the barite pre-flotation, coarse apatite (two columns) and tailings regrind flotation Circuits. Overall, 66 mechanical cells (300 ft3 each) were replaced by only six flotation columns, designed by Cominco Engineering Services Ltd - CESL.The present paper describes the stages of process development, pilot plant testwork and implementation of the industrial project, highlighting the most relevant aspects of each of them. The results achieved are related to improvements in flotation selectivity, gains in P205 recovery and better process control, resulting in better quality products and lower production costs. Other benefits included a decrease in flotation reagents, electrical energy and maintenance materials consumption. These factors contributed to a significant decrease in the cost of phosphate rock production at Serrana, in Araxa - M G."

Jan 1, 1999

By Jom Kresta

Fundamental changes in the Bitumen Production process at Syncrude have led to the integration of Mining and Extraction operations. Successful operation of the integrated process requires the coordinated effort of several business units. Hence, decision-making has become increasingly more complex and better tools are required. IO2 is a collaborative effort to develop a proof-of-concept prototype of a distributed decision-support system for integrated short-term production and maintenance planning with fleet allocation and dispatching. The prototype includes three main modules (planning, dispatch, and maintenance), a shared database, and a simulation module. At this stage, this prototype is used to plan and operate a simulated mining operation. It is used to demonstrate the viability of the chosen systems architecture and algorithms, as well as the information flows and interactions necessary for improving the overall performance of the integrated operation. While the problem is demonstrated using Syncrude?s site, the methodology is applicable to most integrated resource allocation problems.

May 1, 2002

By Arnaud Faucher, Claude Bazin, Marilène Renaud, Mohamed Mai Manga

"Grinding circuits are operated in the presence of disturbances due to ore changes and equipment malfunctions. One of the challenges faced by the operators is the detection of a disturbance, the identification of its origin and of the action needed to minimize its impact on the process. Hydrocyclones overloading, worn or partly plugged apexes of the units of a nest, surging and internal liner detachment may cause a loss of classification capacity and quality. Recovery losses in downstream leaching or flotation circuits justify the effort in developing techniques for the detection of hydrocyclone malfunction. Two approaches for the detection of hydrocyclone fault are presented in this paper. The first proposed method uses the conventional sensors available in a grinding circuit allowing real time detection of hydrocyclone abnormal operation. The second technique is based on the use of vibration sensors installed on the hydrocyclone of a nest. This last technique enables the classification of the hydrocyclone malfunction as surging, overloading and plugged apex. The two techniques can be combined to increase the robustness of the problem detection.INTRODUCTIONHydrocyclones are used for many purposes ranging from water separation, fines removal and obviously for the preparation of the feed for subsequent concentration circuits in a mineral processing plant. The strategic role of the hydrocyclones for the preparation of the feed to the concentration circuit is often underestimated because of their simplicity of operation and robustness (Napier-Munn et al., 1996; McIvor, 1988). It remains that despite their simplicity, hydrocyclones have been studied extensively from 1970 to 1990 with the objective of developing mathematical models of their operation to be incorporated into grinding circuit simulators (Napier-Munn et al., 1996; Lynch, 1977; Flintoff et al., 1987). Such a development effort is already an acknowledgement of the importance of these units in a mineral processing plant. Several authors (Del Villar et al., 1996; Plitt and Kawatra, 1979; Casali et al., 1998) proposed soft sensors to estimate the classification efficiency of hydrocyclones using sensor measurements. However, few of the proposed sensors are used in the industry. More recently several papers were published to discuss the application of 3-D modelling of the hydrocyclones (Narasimha et al., 2005; Cullivan et al., 2004) and sensors (Bond et al., 1999; Neesse et al., 2003; Hou et al., 1998; Olson and Waterman, 2004; Williams et al., 1995; Willams et al., 1997) to help in the detection of hydrocyclone malfunction."

Jan 1, 2010

By A. R. House, G. W. Shepherd

Newmont USA Limited owns and operates the Phoenix Mine near Battle Mountain, Nevada, USA. The existing milling facility has operated since 2006 (House, 2010). Following the startup of the milling operation, and coupled with the upswing in the copper market, Newmont realized that Phoenix had no process option to treat transition and oxide copper ores. This meant that potentially revenue generating ore would be mined as waste. With no system in place to treat the transition and oxide copper, work began to determine the most feasible approach. After evaluating multiple options, the flow sheet was set for a runof- mine (ROM) heap leach pad and solvent extraction/ electrowinning plant (L-SX/EW). This paper will discuss the eight years of successes and challenges with developing the copper L-SX/EW plant and achieving commercial production of copper cathode.

Jan 1, 2014

By Michael Li, Arie Moerman

"Paste backfill as a means of supporting underground mining is gaining popularity. Despite this trend, engineering and design of mine paste backfill systems are still largely based on empirical methods rather than established scientific principles. Because of a lack of sound understanding of mineral paste flow, some degree of trial and error is often involved during commissioning and operating of new paste fill systems. New operations often have to be built with flexibilities and contingencies, escalating the overall project costs.Disciplines that can lend some science to mineral paste flow include slurry transport, fresh concrete rheology, and soil mechanics. This paper reviews the applicability of some scientific and engineering principles found in those related disciplines to mineral paste flows. Examples are given to illustrate important points. The phenomenon of mineral paste flow is examined from new perspectives. Gaps in our understanding of mineral paste rheology are identified and from those some future research directions naturally emerge. Status and problems of the current engineering and design practice are also briefly discussed.INTRODUCTIONPaste backfill as a means of supporting underground mining is gaining popularity. Despite this trend, engineering and design of paste fill production and distribution systems today are still largely based on empirical methods rather than established science. One of the weaknesses of such empirical methods is the lack of scalability and transferability of rheological data from pre-engineering test phases to production phases. It is not uncommon that flow fiction data generated from expensive loop pumping tests turn out to be uncharacteristic of the paste in fullscale production. In such a case the operators have to re-climb the learning curve, sometimes with expensive disruptions to the mining operation."

Jan 1, 2002

By H. Ewaschuk

"INTRODUCTIONRio Algom's involvement with the Enviro-Clear thickener began in May 1975, when tests on a laboratory waif were carried out by our Research and Development group. Commencing in June, further tests were carried out using a 3 foot diameter pilot unit. By December, a 30 foot full-scale thickener had been installed. In the near future, 3 more Enviro-Clear thickeners will be commissioned. With in the space of a year, almost $2.5 million had been committed to liquid/ solid separation facilities using the Enviro-Clear thickener. This paper briefly traces the extent and development of this commitment.BRIEF HISTORY OF QUIRKEQuirke Mine started operating in September 1956 at a rated capacity of 3,000 TOD. Because of market conditions, Quirke was shut down in December 1960. The facilities were re-opened at an increased capacity of 4,000 TPD in July 1968, by which time the demand for uranium had returned. Also, a second shaft was sunk, and by 1970, all of the ore treated in the concentrator was coming from the new Quirke II mine. The Quirke I stopes were allowed to fill with natural seepage. As well, acidic barren solution from the concentrator was pumped underground.With increasing demand for uranium, the capacity of Quirke will be further expanded to 7,000 TPD by 1978. Studies of how this expansion could best he carried out led to the consideration of a fairly new piece of equipment, the Enviro-Clear thickener, for certain operations in the concentrator. These operations are as follows:"

Jan 1, 1977

By M. Cai

A practical simple method is proposed to estimate the tensile strength (st) of strong brittle rocks from the strength ratio of R= sc/st = 8 sc/sci, where sc is the uniaxial compressive strength and sci is the crack initiation stress in an uniaxial compression test. 8 is the Griffith strength ratio and the term sc/sci accounts for the difference of crack growth or propagation in tension and compression in uniaxial compression tests. sci can be reliably obtained from volumetric strain measurement or acoustic emission (AE) monitoring. With the strength ratio R determined, the tensile strength can be indirectly obtained from the result of uniaxial compression tests. In addition, a practical estimate of the Hoek-Brown strength parameter mi is presented and it is suggested that mi = 12 sc/sci can be applied to strong, brittle rocks in high confinement zone and mi = 8 sc/sci can be applied to low confinement to tension zones. It is found that the predicted tensile strengths and Hoek-Brown strength parameter mi using this method are in good agreement with test data. The rock strength parameters like st and mi, which require specialty tests such as direct tensile (or Brazilian) and triaxial compression tests for their determination, can be reasonably estimated from uniaxial compression tests.

May 1, 2009

By J. R. Goode

"Coarse ore sorting is here defined as the physical separation of a mixture of coarse (+3/8 inch) ore particles into two or more separate groups of total value greater than that of the unsorted ore. An ore will probably be sortable if the geology of the orebody and the mining practices employed meet conditions outlined in this paper.The paper points out how sorting can substantially reduce tonnage variable operating costs because sorting can double the mill head grade of amenable ores by rejecting waste rock from the mine output. The effect of sorting on ore reserves is outlined. It is also suggested that sorting is a low cost alternative to conventional expansion.The mode of operation of the Ore Sorters Kadel 13 Photometric and MK VI A Radiometric sorters is detailed. The report concludes with detailed descriptions of the photometric sorting plant operated by the Doornfontein Gold Mining Company is South Africa and the Radiometric Sorting Plant presently under construction at the Schwartzwalder mine of Cotter Corporation in Colorado."

Jan 1, 1975

By Steve Wilson, Bern Klein, Jeff Drozdiak, Stefan Nadolski, Andrew Bamber

"In the adaptation of high pressure grinding rolls (HPGRs) to hard-rock mining applications, circuit development has mainly focused on placing HPGRs in the role of tertiary crusher in the preparation of ball mill feed. In order to take advantage of the potential energy benefits associated with HPGR and stirred mill grinding technologies, work was done to investigate the potential of and resultant energy benefits of placing the HPGR in series with a high speed stirred mill in replacement of the conventional cone crusher / ball mill arrangement. The proposed circuit was designed to operate with two stages of HPGR grinding followed by high speed stirred milling.Using a pilot-scale HPGR unit inline with a 20 liter stirred mill, the design criteria, circuit arrangement and consequent comminution energy requirements for a circuit processing copper sulphide ore from Teck Resources’s Mesaba Copper project were determined. These results were then compared to two other circuits, an HPGR / ball mill circuit and a conventional crusher / ball mill circuit processing the same ore.The testwork indicated at a proof-of-concept level that the HPGR / stirred mill circuit could potentially be appropriate for this duty and further work on the concept is merited. While the results indicate that the HPGR component of the circuit was more energy efficient than conventional cone crushing, the energy efficiency of the stirred mill was found to be lower than that of a comparable ball mill undertaking the same duty. However, increased energy efficiency of the stirred mill portion of the circuit is possible with further optimization and further work on the concept is indicated."

Jan 1, 2010

By C. J. Brown

Controlling the level of impurities in copper refinery electrolytes is essential to achieving acceptable cathode purity. Purge of electrolyte is not an entirely satisfactory solution since the cost of neutralization, waste disposal, and replacement acid can be appreciable. The APU® process utilizes ion exchange resin to sorb sulphuric acid while rejecting metal salt impurities. Extensively employed for recovery of waste pickling and anodizing acids since 1977, the system is now being used at several refineries for removal of contaminants such as antimony, bismuth, iron, and nickel. The purified acid, which is recovered from the resin by water elution, is recycled back to the refinery tank-house, while the metals are typically recovered from the de-acidified by-product solution by precipitation.

Jan 1, 2005

By Unkown

To the Membership of the Institute Gentlemen: The Mineral Industry of Canada in 1948 The preliminary estimate issued by the Dominion Bureau of Statistics and tabulated in the Bulletin of January, 1949, indicated that the value of Canada's mineral production in 1948 reached an all-time high of $808,180,216, showing an increase of 25 per cent over the previous record of $644,696,007 established in the preceding year. The output value of metallics was increased by 22.4 per cent; of fuels, by 43.7 percent of other non-metallics, by 19 per 'cent; and of structural materials, by 16.8 per cent. The value of metals produced in 1948 at $483,770,759, was about $87,000,000 more than in the previous year. There were substantial increases in the tonnages of copper, lead zinc nickel, and other base metals produced, but the rises in market prices for such metals accounted for most of the gains in output values. Production of gold at 3,495,403 ounces valued at $122,339,105 indicated an increase in volume of approximately 500,000 ounces and an increase in value of 14 per cent. Despite the benefits provided under the Emergency Gold Mining Assistance Act 1948 the volume of gold produced in the year was still nearly 2,000,000 ounces less than the record of 5,300,000 ounces established in 1941. The value of mineral fuels produced in 1948, at $158,787,255, was 44 per cent above the 1947 total. Coal production at 18,431,250 tons valued at $107,298,757, while substantially higher than in the preceding year was still half a million tons below the record reached in 1942. Striking developments in the Leduc field in Alberta were responsible for bringing the output of crude petroleum in the year to a new high of 12,098,166 barrels, valued at $36,858,959.

Jan 1, 1949

By A. B. Cron, R. MacPhail, L. Melis, K. Armstong

"Mt. Milligan is a porphyry gold/copper deposit in north-central British Columbia. Diluted and mineable drill-indicated reserves total 449 million tons at an average grade of 0.013 oz gold/ton and 0.19% copper. Large-scale commercial development of the deposit will make Mt. Milligan Canada's third largest gold mine.Metallurgical investigations for the Mt. Milligan project were done in three phases: scoping tests in the first half of 1989; bench-scale work from October 1989 to April 1990; and a pilot plant program in May and June 1990. Various process alternatives for the recovery of gold and copper are described and results are presented. Net smelter return evaluations led to the selection of optimum process conditions for maximizing revenue from gold/copper flotation concentrates.The selected flotation circuit and basic design criteria are described. Forecast average recoveries over the presently-defined 20-year project life are 75.2% for gold and 90.5% for copper in a copper concentrate averaging 17.6% copper and 1.0 oz gold/ton. 1.0 PROJECT LOCATIONThe Mt. Milligan porphyry gold/copper deposit is located in northcentral British Columbia, 150 km north of Prince George, British Columbia. The site is at an elevation of 1,100 m in an area of logged, gently-rolling topography. Nearby communities include MacKenzie and Fort St. James. Climate in the area is moderate and there is direct road access to the property. A location map is presented in Figure 1-1."

Jan 1, 1991

"The Antamina orebody is a geologically complex, polymetallic skarn located in the Peruvian Andes. A range of copper and copperzinc ores are campaigned separately through the concentrator producing copper and zinc concentrates as well as lead and molybdenum by-products.Ore type classification at Antamina is based on chemical assays; geological or lithological variations are not considered. Consequently, each ore type demonstrates a wide range of concentrator performance.Antamina is currently implementing a system to track ore movements from the shovel face to the concentrator. Relatively sophisticated models of run-of-mine and coarse ore stockpiles ahead of the mill will be used to account for the variable delay between mining and milling.One of the numerous benefits of ore tracking is the ability to directly associate the measured concentrator performance with a physical location in the orebody. Using existing mine planning software, three-dimensional models can be created of such performance measures as metal recovery, concentrate quality, operating cost, and reagent consumption.Such a database of information allows the true value of different ore sources to be determined. The value of an ore source is conventionally measured as metal content (individual or combined ‘equivalent’) with a cut-off grade applied to indicate some base level operating cost. However, the true value of an ore source should include dynamic factors like haulage cost, reagent use, smelter penalties, and even prevailing metal prices. If an ore source is considered from all perspectives rather than simply its potential to deliver value, the concept of ore becomes more flexible. Any ore source that reveals itself to be unprofitable can be eliminated from the mine plan or possibly blended with others to improve its value. The ability to predict mill performance, and thereby profitability, is a powerful tool.In an operation such as Antamina, where managing ore sources, campaigns, and the delivery of a variety of concentrates in a narrow timeline to customers is a daily challenge, prediction is the key to success and improved efficiency."

Jan 1, 2005

By E. J. Fuller, J. C. Monette

"Gold and silver cyanide complexes are presently desorbed from activated carbon by means of hot caustic elutions. These solutions may or may not contain additional sodium cyanide. There are several parameters which affect the rate of stripping. Some of these include pH, ionic strength, and temperature. (1) Stripping is conducted in recirculating (ZADRA) or once through (AARL) circuits.This paper describes the development of a new chemical eluant which significantly increases the rate of stripping of both gold and silver cyanide complexes from activated carbon. Two case history applications are also described.INTRODUCTIONAdditional cyanide is used in strip circuits in order to prevent its depletion which could lead to precipitation of base metals or lead to a change in the nature of the gold cyanide complex to one which does not strip as easily. (2)The strip circuits that are able to function efficiently without the use of cyanide are mostly those where the carbon is acid-cleaned after stripping.Once the minimum cyanide requirement to maintain the complexes in their proper state are fullfilled, any futher incremental increase in the level of cyanide will have no bearing on the rate of stripping. (3)DEVELOPMENT OF THE NEW ELUANTGeneral DiscussionVarious carboxylated materials were investigated including octanoic acid, polycarboxylic acid (various molecular weights), salicylic acid, polymaleic acid, acetic acid. benzoic acid, terephthalic acid, 4, bi-phenyl carboxylic acid, phosphoric acid and stearic acid.The initial work was done on medium activiiy, non acid-cleaned carbon. The silver to gold ratio on the carbon varied greatly.Two different blanks were used. The first was an elution using a 2% caustic and 0.4% cyanide solution while the second was a 2% caustic elution."

Jan 1, 1992

By Doug Smith, Gary Taylor, Paul Ogryzlo

"Uranium mining and processing typically requires large quantities of high-grade reactive quicklime for the neutralization and clean-up of contaminated mine water and mill process waste streams. Currently the Saskatchewan uranium industry’s lime requirements are being supplied from deposits located in Manitoba and Alberta, resulting in transportation costs, which equal or exceed the market value of the product. During the summer of 2001, the northern village of Pinehouse located 220 kilometers south of the Key Lake uranium mill, staked two previously discovered limestone deposits. The relatively shallow deposits, known as Missi Island and Sleeping Giant are located in close proximity to one another, approximately 35 km south of Pinehouse adjacent to highway 914. This paper describes the results of a scoping study carried out by AMEC for the development of the two deposits based on a seasonal limestone mine and a continuous 40,000 to 60,000 tpy wood fired calcining plant designed to supply all of the quicklime needs of the Saskatchewan based uranium industry. Also described are the results of calcining and customer acceptance testwork on samples of lime prepared from recent Pinehouse limestone drill core. The potential benefits of the project include a significant new source of revenue for the community of Pinehouse, lower lime costs for the Saskatchewan uranium industry and employment for northerners in the mining, processing and wood harvesting operations.IntroductionInterest in the Pinehouse/Massinahigan River area for limestone was precipitated by the results of a 1977 industrial minerals drill hole program by the Saskatchewan Department of Mineral Resources. These results led to the acquisition of land in the area by Missi Island Mines Ltd who carried out extensive exploration during the period 1978-1982. They discovered a deposit on the southwest side of the Massinihigan River thought to contain approximately seven million tonnes of limestone with an average grade of 94.5% CaCO3. Missi Island carried out preliminary feasibility studies and prepared an Environmental Overview Statement. However, in spite of positive recommendations, the project was dropped in the mid 1980’s."

Jan 1, 2003

By D. M. Doyle

"The Strathcona Concentrator operations, the application of control systems in the crushing, flotation and tailing fill sections, and current and future computer control concepts are described in this paper.The computer has been used for reporting and monitoring roles and operating the on-stream analyzer since start up of the mill in 1968, while over the past twenty months, it has been used for process control. The systems which have been developed include:1. The blending of pentlandite concentrate with pyrrhotite concentrate to produce a special product of constant nickel analysis.2. The blending of cement with tailing fill to produce backfill of consistent cement content.3. The supervisory control of xanthate, frother and pH to the flotation circuits to maintain the nickel copper concentrate grade within narrow limits.IntroductionThe Strathcona Concentrator is currently treating 7,200 tons per day of an ore which contains nickel associated with the minerals pentlandite (28 -32% Ni) and pyrrhotite (0.3 -1.0% Ni). The ratio of the nickel minerals varies from 4 to 15 parts of pyrrhotite to 1 part of pentlandite over the orebody. The production of a high grade concentrate re4uires the separation of this small quantity of .oentlandite from the much greater proportion of pyrrhotite and gangue and is complicated by the presence of two pyrrhotite minerals differing in nickel content, floatability and magnetic susceptibility."

Jan 1, 1974

By Patrick Rennkamp, Wolf-Dieter Trodel, Andy Fearn

"The Jansen shafts are completed using purely mechanical excavation. This paper summarises the geology, a description of the shafts, the method used for excavation and the results achieved along with the challenges encountered and the solutions developed during the project. This experience is now being applied in the next generation machines and shaft sinking processes. This pioneering approach is changing shaft sinking in soft and medium to hard rock. INTRODUCTION The Jansen Mining project located approximately 150 km east of the city Saskatoon is the location of the BHP owned potash mine with an expected mining output of eight million tonnes annually upon completion. Mining contractors DMC Mining Services have used two Herrenknecht Shaft Boring Roadheaders (SBRs) to excavate the two blind shafts with an approximate excavation diameter of ten metres (inner diameter approximately 8.3 m) to depths of -975 and -1005 metres, respectively. The SBRs excavate the rock by a partial-face cutting method, using a transverse cutting drum mounted on a telescopic boom. The excavated rock is then conveyed away from the bench by an innovative pneumatic system and transferred into muck buckets to be hoisted to the surface. No drilling and blasting was done to keep to the BHP philosophy of using only mechanical excavation for this reference project. BHP VISION – MECHANICAL EXCAVATION BHP focused on mechanical excavation at Jansen due to the following perceived benefits: 1.No workers in the excavation chamber (shaft bottom), minimizing the exposure to traditional shaftsinking hazards associated with working in the shaft bottom. 2. Minimal damage to the rock fabric reducing the need for ground support and avoiding potential impact damage to freeze tubes located around the shaft. 3. Accurate excavation diameters with no overbreak, reducing volumes of rock to be removed and replaced with concrete lining."

Jan 1, 2019

By K. Turgeon, J. -F. Boulanger, L. Whitty-Léveille, C. Bazin

"Several companies targeting Rare Earth Elements (REE) around the world have completed a Preliminary Economic Assessment showing positive project financial results. Although REE ores may contain high REE value, financing these projects remains difficult in part due to the number of processes required to valorize the elements and the relatively low yield of these processes. Direct ore leaching without the production of a concentrate may reduce the capital and some operating expenditures through process simplification, and increase revenues because of REE recovery improvement.A silicate REE ore is used to test various hypotheses regarding whole ore processing and to develop a simplified flowsheet. An atmospheric leach (200 kg/t H2SO4) of crushed whole-ore containing 0,6% REE, followed by impurity removal and REE precipitation recovers 80% of the REEs in a solution containing REE and Th. The high value contained in most REE deposits makes whole-ore approaches worth considering for most projects, given the losses of valuable species typically associated with the production of a REE mineral concentrate from the ore. INTRODUCTIONRare Earth Elements (REE) find applications in modern and clean technologies, whether civil, industrial or military. With China producing more than 90% of the world’s REE, the embargo imposed by this country in early 2010 increased REE prices for a three year period. With prices having shrunk back many-fold from their peak value, projects put forward during the hike are struggling to secure financing. Owing in part to unconventional processes such as acid-baking and solvent extraction, REE plants are high capital cost and high operating-cost units, and present technological risks (Verbaan et al., 2014)."

Jan 1, 2016

By Zbigniew J. Hladysz

A Deep Underground Science and Engineering Laboratory (DUSEL) is being planned at the site of the former Homestake Gold Mine in Lead, South Dakota, under the sponsorship of the US National Science Foundation (NSF) in cooperation with the US Department of Energy (DOE). This national facility will host a variety of multidisciplinary science and engineering experiments including physics experiments that require shielding from cosmogenic radiation. Geotechnical mapping was performed in 2010 in large excavations of the Davis Campus at the 4850 Level of the former Homestake Mine. LIDAR mapping included laser scanning using a red light laser scanner and 288 Mpixels 360° still camera. The resulting vector map with the photographs digitally draped over the model, was used to create an accurate, virtual model of the excavations. For model verification, the laser scanning was accompanied by surveying and manual mapping of the geology and rock structure. The immediate use of the model was to perform structural analysis and interpretation of geology needed for the design of the DUSEL?s super large excavations. The second round of scanning, after the application of shotcrete to the excavations walls, will be used as a technical blueprint to assess the effectiveness of shotcrete application.

May 1, 2011