Search Documents

By Howard Roscoe

Linking Ashford International Station to the new Channel Tunnel Rail Link required over 5000 rotary bored and CFA (continuous flight auger) piles to form tunnel walls and viaduct foundations and to support overbridges and trackside barriers.. Much of the work was carried out close to the existing railway infrastructure. Plunged columns were used to maintain traffic flows over the tunnel site during construction. The results of an extensive programme of vertical and lateral load tests on bored and CFA piles in heavily overconsolidated Weald Clay are compared to illustrate the relative importance of stress relief and of prolonged exposure to bentonite. The completion on schedule of this major piling and ground engineering contract (value £30 million) demonstrates that collaborative working in partnership produced cost effective solutions to a series of challenging technical and logistical problems.

Jan 1, 2002

By John J. Vieaux

Allowable loads on Dynamically-Cast-In-Place Piles (the Franki type) can be correlated with N values from the Standard Penetration Test. Using a constant developed by Nordlund, a conservative value for load-carrying capability of a DCIP pile is developed. The DCIP pile and method of installation is briefly described.

Jan 1, 1984

By Jorj O. Osterberg

The Osterberg (O-Cell) Method makes it possible to separate the side shear resistance (skin friction) from end bearing. The O-Cell is placed on or near the bottom of a drilled shaft and after the concrete is poured and cured, an equal upward and downward pressure is applied. From the test, the load-upward deflection curve in side shear and the load-downward deflection curve in end bearing are drawn. Typical curves are shown where the ultimate load in side-shear is reached and where the ultimate load in end bearing is reached. Several examples of tests in which the test load reached ultimate loads far in excess of what was expected are shown. The side shear in rock sockets is shown to be much larger than generally estimated. Examples are given of where side shear is smaller than expected and the reasons discussed. Disturbance of the sides of drilled holes due to poor construction techniques and ways to avoid these conditions are considered. Examples of bottom hole disturbance are given and ways to prevent the disturbance are discussed. A graph showing the actual measured capacity of drilled shafts compared to the estimated capacity as a function of the hardness and strength of the soil or rock is presented.

Jan 1, 1999

By Derek J. Lennon

Ground conditions in central Glasgow generally comprise loose granular deposits overlying stiffer soils. CFA piling would normally be preferred for urban sites in these ground conditions, but flighting of the superficial deposits has on occasions resulted in building damage. Over the last five years rotary bored piling with vinyl polymer support fluid has proved to be an economic alternative to bentonite slurry. Two case histories in central Glasgow are described in this paper, one for piles founding in granular soils and one for piles founding into bedrock. A comparison is made between the methods required for disposal of the liquid waste from bentonite and vinyl polymer slurries.

Jan 1, 2006

By Braja M. Das

Laboratory model test results for the ultimate uplift capacity of square and circular foundations in saturated clay (ø=0) have been presented. The results of the present model tests for square foundations have been compared with the previously published laboratory model tests results on circular foundations. Based on the comparison, it appears that the critical embedment ratio of square and circular foundations increases from about 3 for soft clays to about 7 for medium to stiff clays. By using the experimental results, an empirical procedure has been suggested for determination of the ultimate uplift capacity of belled pier foundations in saturated clay.

Jan 1, 1987

By R. Stenne

This paper presents the trends in deep foundations in Europe, both in terms of design and construction. Eurocode 7 which is a design code for geotechnical engineering will be introduced in the European Union member countries, and will oblige geotechnical engineers to abandon traditional methods based on a global factor and adopt a new approach based on partial factors of safety. Execution codes (for construction of foundations and other geotechnical processes) are currently being introduced without problems. Ever more demanding environmental constraints push foundation contractors to adapt old techniques and develop new ones to comply with new regulations.

Jan 1, 2000

By Garland Likins

Where soil conditions are favorable, augercast piles have significant economic advantages, but they also have some uncertainty due to the in construction methods. To confirm structural integrity, static testing can be performed on a small sample of piles. Other Non-Destructive Evaluation methods like Pulse Echo are frequently specified for a large percentage of the remaining production piles. However, such NDE methods require testing the pile after the grout/concrete has hardened. If problems are found, then the repair or replacement can be relatively expensive. The confidence in the quality of these piles can be improved by automatically monitoring the grout pumped as a function of depth during the grouting phase of installation. If a low grout volume is detected, the pile can be redrilled and regrouted immediately while the piling rig is still in place and the grout still fluid. This considerably reduces remedial costs. To be effective, such installation monitors must accurately determine both grout volume and depth during installation and be rugged simple to operate. Such an equipment can be of great help to the installation crews. The assurance gained may reduce the need for subsequent NDE tests. The quality of inspection of driven piles depends heavily on the inspection personnel. While inspection is critical in a good installation, it is sometimes assigned a low priority. Inspection personnel in many cases are technicians with little pile experience. They may not understand the project needs or even how the pile driving equipment works. The task is often monotonous and any distraction makes accurate record keeping difficult. In some cases inspection is totally ignored for lack of qualified personnel. Electronic systems can automatically and accurately monitor driven pile installations and include documentation of certain hammer performance parameters. This paper describes equipment available and routinely in use for automated monitoring of both augercast and driven piles and demonstrates applications on typical construction sites. The paper also discusses benefits and limitations of the alternative NDE tests. KEYWORDS: Augercast Piles, Piles, Installation Monitoring, Pulse Echo Method, Integrity Testing

Jan 1, 1999

By Y. G. Qin

In this article an experimental study of axial bearing capacity of half-closed steel pipe pile installed at BKSH dock is presented. In comparison with open and closed end piles, half-closed end pile is considered to have high bearing capacity and good penetration, that is, it not only has a capacity as twice as the same size open end steel pipe pile, but also has blow counts as half as the same size closed end steel pipe pile. It is economic to use half-closed end pile in soft ground without a deep deposit of thick stiff clay. This article also describes a large scale model pile test and preliminarily analyses mechanism of improvement of bearing capacity of half-closed end pile with emphasis on effect of squeezed soil on side friction; an empirical approach is presented in which side friction is related to density of squeezed soil and which is useful for reasonably chosing side friction of different types of piles in design of foundarion.

Jan 1, 2010

By D. A. Greenwood

Dr David Greenwood opened the first technical session of the conference by highlighting the diverse nature of the papers in this session but drawing attention to the common theme that each solved a particular problem. PAPER 1.1 Tony Elliott introduced his paper on deep mix-in-place soil/cement stabilisation by stressing its simplicity. The engineering solution adopted at Elland was detailed in his paper and had formed the key to success of the project. The process itself is not widely used or known in the UK, although it has the potential to achieve significant benefits, subject to proper engineering control being exercised. It was explained that although the concept was not new, development of the technique for soil modification was relatively recent. The alternatives to mechanical mixing are injection, which is very dependent on soil type, site geometry, etc, and jet grouting; both processes are soil-responsive, and not easily monitored or programmed, difficulties which can largely be overcome by mixing. To achieve this at depths to say 30m requires high-powered, high torque machines and has resulted in significant equipment development.

Jan 1, 1991

By Han Jie

The results of full scale plate load tests on stone columns on soft clay in coastal areas are presented in this paper. Four load tests were made, two of which were performed on the ground treated with stone columns, one on an isolated stone column and the last one on the untreated ground. For a given stress range, the settlement of the rigid plate, the stress concentration factor, and the excess pore water pressure were measured. It is found that the distribution of vertical stress beneath the rigid plate supported by the composite ground of stone columns is very different in shape from the one by the untreated ground, that the stress concentration factor has a relation with the stress level and time, that the stone columns increase the bearing capacity up to by 2 times, and that the ground stabilized by stone columns is of great advantage to keep the foundation stable.

Jan 1, 1991

By Jacob Chacko

The east span of the San Francisco-Oakland Bay Bridge (SFOBB), which is one of the most heavily traveled bridges in the world, will be replaced due to seismic safety concerns. The majority of the new bridge will be founded on large-diameter (1.8 to 2.5 meters), approximately 60- to 100-meter-long pile foundations The large-diameter steel pipe piles and soil conditions are similar to those used/encountered in many offshore structures. Thus, the design methods used are based on site-specific modifications to the procedures recommended by the American Petroleum Institute rather than the conventional procedures that have been formulated and used for the design of much smaller piles. Pile foundations will experience their maximum loads during the design earthquake. For the Safety Evaluation Earthquake, tension loads of up to approximately 80 to 90 meganewtons (MN) and compression loads of up to approximately 120 to 140 MN were calculated. Due to the economic importance of the SFOBB and the consequences of catastrophic failure in both economic and human terms, the design and analysis of the pile foundations supporting the bridge consider a number of aspects of pile-soil behavior that are normally ignored. Those aspects include: 1) the effects of consolidation and setup, 2) the behavior under dynamic loading, 3) the losses of resistance under cyclic loading, and 4) the load-settlement behavior of the piles under severe cyclic loading conditions. Since the treatment of complex aspects of pile foundation behavior is not codified in any guiding documents, several project-specific methods were developed for design and analysis of the foundation piles.

Jan 1, 2002

By S. Narasimha Rao

Significant amounts of lateral load may act on pile foundations supporting structures such as transmission line towers, tall structures, bridge abutments, offshore platforms, quay wails, harbour structures and anchorages for water front structures. There were several theoretical and experimental studies conducted on laterally loaded piles in clays to determine ultimate lateral capacity and deflections under working loads. Under a lateral load, a pile deflects in the direction of load application and the soil in front of the pile offers resistance to this movement. The ultimate lateral resistance of a pile can be estimated considering the statics of the pile for a known distribution of soil resistance with depth. In this paper, considering the contributions from both lateral shear drag and frontal passive earth pressure, a method has been proposed to estimate the ultimate lateral capacity of rigid piles in clays. The lateral shear drag has been estimated in terms of adhesion and shape factor. A few load tests were conducted on model piles subjected to lateral loading and these experimental values are used in verifying the proposed method. The reported results obtained from both model tests and field tests were used in support of the predictions made. In all the cases, there is a good agreement between the predicted and measured capacities.

Jan 1, 1996

By Alan G. MacKinnon

Loads and stresses from pile driving are increasing from heavier piles and more powerful hammers. Stresses can be dangerous to equipment stability. Equipment developer MacKinnon tells how to compute stresses for all positions of the crane boom and angles of pile batter. From a paper presented at the DFI-University of Hawaii Seminar, April 1985.

Jan 1, 1986

By Shachar Magali

This article describes two new concepts regarding the CFA (Auger Cast) piles. The first one, MALI Effect, is an approach to control the casting phase, while the second one, NETA Shear, is a technique which converts the drilling rig into a geo-mechanical tool. We look upon the system of the auger and the ground as a piston inside a cylinder. When concrete (grout) is pumped into that system, an up lift force is generated (We call that force MALI Effect). That up lift force reduces the needed tension in the pull up cable. By analyzing the tension force in the cable we detect the up lift force of the concrete. That pushup force is the product of the real concrete pressure at the bottom of the auger by the area of that bottom. As the area is known, the real pressure is accurately calculated. A control loop which is based on MALI Effect is very sensitive, precise, objective, reliable and easy to be used. All the process is based on pure real physical measurements. The system has no assumptions, no comparisons, no parameters, no zeroing and no adjustments. When we penetrate into the ground like a theoretical screw, for about a meter in depth, and then brake the main cable while rotating the auger, a set of forces generates. As the auger tends to keep penetration, but the cable holds it - a tension force develops (We call that force NETA Shear). Analysis of that tension force shows that it relates to the ultimate shearing capacity of the ground.

Jan 1, 2000

By D. E. Sherwood

Mr. Tamaro introduced his paper which concerned the construction of foundations for the buildings and related infrastructure of the World Financial Center on a reclaimed shoreline site at the Southern tip of Manhattan Island. This large project presented difficult design and construction problems, both geotechnical and structural. All structures were supported by foundations carried to rock. Two of the buildings were supported by conventional pier (pad) foundations constructed within diaphragm wall cofferdams. The remaining structures were supported by either piles to rock or caisson (large diameter) piles with socket depths drilled through the rock of up to 7.6 metres. Underground services, railway and proposed road tunnels all affected the installation of foundations. The proposed road tunnels for the new six lane 'Westway' would involve an excavation 12 metres deep adjacent to and under three buildings. This problem was solved by an agreement that tower windloads would be taken by the tower foundations and not distributed through the basement walls. This was achieved by a system of battered caissons founded on the rock and arranged so that adjacent caissons were founded in different rock masses. Diaphragm walls were restrained using tie backs. Ground testing indicated an exposure to D.C. stray current corrosion of all underground construction. As a result all of the foundations were isolated from the ground by non-conductive materials. In the case of piles and caissons the reinforcing for the caisson was fully protected by concrete and all outside steel used for the installation of piling was considered sacrificial and not used in the computation of long term load carrying capacity.

Jan 1, 1991

By Alfred H. Brand

New York City contains extensive deep deposits of glacial lake varved silt and clay, often overlain by organic soil. An 18 story building was proposed for Manhattan's upper East Side in one such area where bedrock is approximately 200 ft deep. Various pile and caisson alternatives were considered extending through the glacial lake soil to rock, but all proved beyond the project budget. Laboratory testing showed that the glacial lake deposits were preconsolidated. A test pile program using auger cast piles bearing in the glacial lake deposits proved that such piles could safely carry a load of 60 tons per unit. The auger cast pile scheme was estimated to be more economical than a deep pile alternative. A further benefit was that the vibration-free pile installation procedure posed less risk to adjacent structures which had been founded at shallow depth in fill above organic deposits and were stressed and cracked due to prior settlement. The project was designed with the anticipation that the glacial soils beneath the tips of the piles would produce a building settlement of 1 to 2 inches. The building was constructed in 2001 and 2002. It has been completed and is now occupied. Settlement data show that the building is performing as predicted. The auger cast pile scheme founded in a compressible stratum has proven to be successful and is a very unusual foundation alternative.

Jan 1, 2003

By A. R. Gaba

Phase I of the Canary Wharf development in London's docklands involves the construction of six fifteen storey buildings located predominantly over water of the West India Docks. The buildings are supported on some 1000 No., 25m long, open ended steel tubular piles driven through 10m of dock water to found in dense sand at a depth of about 15m below dock bed level. The piles are of composite section with reinforced concrete within the upper 17m of the steel tube. Three trial piles were installed in the dock to investigate the driveability and performance of the driven steel tubular piles. The piles were subjected to dynamic and static load testing. Loads were applied in both vertical and horizontal directions. Vibrating wire strain gauges were installed on the inside of the steel piles, on the reinforcement and in the concrete to determine the relative proportions of the applied load carried by the steel tube and concrete infill and to establish how these proportions varied along the length of the piles. Inclinometers were also installed to monitor the lateral deflection of the piles. This paper describes the driving, construction and testing of the three trial piles. The results of the vertical and horizontal loading tests are discussed and comparisons are made between dynamic and static tests carried out on the piles.

Jan 1, 1989

By Bert R. Oastler

BERT R. OASTLER: Born Atlanta, Georgia, October 19, 1933; B.S. Civil Engineering, Duke University, 1956; Doctor of Laws, Emory University, 1966; Bryan Honor Society; Associate Editor, Journal of Public Law. Partner in charge of litigation for Smith, Currie & Hancock Including federal and state courts, administrative boards, arbitration and negotiation. American Bar Association; American Trial Lawyers Association; Georgia Trial Lawyers Association. Practiced structural steel design at Newport News Shipbuilding & Drydock Company and building construction as an officer in the United States Air Force. Engaged in the building construction business in Atlanta, Georgia as estimator and project manager for five years. Lectured on construction litigation, arbitration and government contracts procurement law for Federal Publications, Inc., Associated General Contractors and other private entities on a nationwide basis. Served as guest lecturer on Government Contracts at Emory University and Georgia Institute of Technology, Atlanta, Georgia. Served as arbitrator in cases for the American Arbitration Association.

Jan 1, 1988

By Charles L. Guild

I will add a few facts about the use and development of the Osterberg Test Load Cell and my association with Jorj. I first met Jorj in 1965 when the Guild Construction Co. drove 12" diameter cast-in-place shell piles for him at the Marquette Cement Co. in Nashville, Tennessee. When I met Jorj at the DFI Trustee's meeting in 1985 at Longboat Key, Florida, he showed me a sketch of his idea about using a test cell at the bottom of a caisson to test the end bearing and side friction on a caisson. He had made a successful trial test in Case International's equipment yard and wondered whether a similar device could be made for a driven pile. At first I was skeptical that it could be done but after thinking about it overnight I told him I felt it was feasible and we would do some work on it. At that time, there was a large bridge job going out for bid in Rhode Island using 14" square prestressed concrete piles'. Based on a record of the Guild Construction Co. Inc. driving over 3,000,000 feet of piling on work for the State of R.I., we felt we would have an excellent chance to be allowed to use them so we designed, detailed and fabricated three for 14" square prestressed concrete piles. As things worked out, we did not test them on this job and have not to date.

Jan 1, 1989

By Willie M. NeSmith

Conventional augered, cast-in-place (ACIP) piles were introduced into the New York City area as a result of the damage to existing structures caused by pile driving operations. ACIP piles are often specified where deep foundations are to be installed adjacent to transit facilities, sensitive underground utilities or in close proximity to existing structures. However, loss-of-ground issues associated with the installation of ACIP piles have prevented the wide-scale use of these systems. Beginning in 2002, Berkel & Company Contractors, Inc. began using its augered, cast-in-place displacement (ACIPD) system in the New York City area. Like conventional ACIP piles, this system produces almost no vibration. Also, as almost no material is brought to the surface, there is no opportunity for loss of ground. This paper presents a description of Berkel's displacement pile system and a brief discussion of six projects in the New York City area that have been executed with this system over the past two years.

Jan 1, 2004