Search Documents

By M. A. El-Sohby

The paper describes some problems encountered with the foundation of a deep drainage caisson constructed on the Nile Bank in Cairo. The use of suction dredging while sinking the caisson led to a piping failure of the sandy soil in the base which was loosened during the process of pumping. A study was carried out to investigate the problem and a procedure was adopted to retain the stability of the caisson.

Jan 1, 2010

By Gandhi

Piled raft foundation under uniformly distributed vertical loads has been analyzed using Finite Element Method. The soil is considered to be linear elastic, isotropic, homogeneous. The raft,pile and the soil have been idealized with eight noded brick elements. Parametric study have been carried out varying pile length, soil modulus, raft thickness, and pile spacing. Design charts have been produced to achieve 50% load sharing between pile and raft for optimum design. Data available in literature is compared with the design chart results and found satisfactory.

Jan 1, 1996

By Pastsakom Kitiyodom

In order to estimate the deformation and load distribution of a single pile subjected to dynamic horizontal load as well as vertical load, a simplified method of three-dimensional numerical analysis, KWaveHybrid program, is developed using a hybrid model. In the hybrid model, the pile is modelled as elastic beams, and the soil at each pile node is treated as springs and dashpots in both vertical and horizontal directions. KWaveHybrid is also able to analyse the static response of the pile. Validity of the newly developed program is examined through comparisons with theoretical values and horizontal dynamic and static pile load test results

Jan 1, 2006

By Arturo Ressi di Cervia

Construction of the drilled shafts for the Brightman Street Bridge Replacement Project were not only challenging due to working over the water but were also challenged by changed soil conditions, concurrent work being performed by an adjacent contractor on the same project, environmental restrictions and severe winter conditions. A total of 36 x 8 feet diameter drilled shafts with 7.5 feet rock sockets were installed for the East and West bascule piers. This project also included Osterberg Cell load testing on two production drilled shafts at each the East and West bascule piers. The results from the load test program were used to fine tune the design of the drilled shaft rock sockets. From a constructability standpoint the reverse circulation drilling method with a pile top drill rig proved to be an excellent choice for drilling the overburden and rock sockets of the large diameter deep drilled shafts.

Jan 1, 2003

By Dan Brown

A method is outlined for computing the contribution of a micropile group to global stability of a sliding mass. The forces in the micropile are computed in a way which accounts for the effect of soil mass movement on the mobilization of axial and shear forces and which maintains compatibility between shear and axial force as a function of displacement. The method provides a rigorous model to incorporate the pile forces into the stability calculations, including the effect of pile forces on the resultant shear and normal forces at the sliding surface. This paper demonstrates the proposed solution using a simple example slope.

Jan 1, 2007

By S. Hardy

The paper describes state of the art non-linear analyses of the pile groups that were employed during the raising of the 133m high triumphal arch which forms the centre piece of the new Wembley stadium in North London. The deformation behaviour of these piles groups was critical during the lifting process, due to the slendemess of the arch structure. The issue was made more critical by the high profile nature of the project. The results of Class A (Lambe (1973)) predictions of the pile group movements are compared with observed displacements and rotations which were accurately measured on site. To illustrate the importance of soil non-linearity on pile group behaviour, comparison is also made with pile group analyses which assume a linear soil stiffness.

Jan 1, 2006

By M. J. Preim

Two case histories are presented on the evaluation of static bearing capacity of piles driven in soils that exhibit time dependent strength changes. Under consideration are a steel and a concrete pile driven into soils generally consisting of silty and clayey fine sand. Pile dynamic measurements and analyses were performed on both piles during initial installation, and also during restrike one week later. This information was used to predict each pile's long term capacity (defined as 14 days after initial drive), which was then compared to that measured with a static load test. Agreement between predicted and measured capacities were remarkably good, with an average error of only 4.5 percent. Two weeks after driving, total pile capacities were three times those at the end of drive. If only the skin friction was considered, however, it increased by an average factor of 16. The increase in pile capacity was determined to be linear over the time period considered.

Jan 1, 1989

By Narong Thasnanipan

In Bangkok due to the prevailing condition of subsoil (existence of considerably weak stratum at top part) deep-seated large diameter bored piles of over 50 m depth with 0.8 -1.8m in diameter have been mainly used for heavy structures such as high rise buildings, elevated expressways, flyovers and more recently for underground subway stations of the first Bangkok MRTA system. As a part of pre-planned quality assurance regime and retrospective investigation, integrity of the piles are tested to obtain the information with regard to the potential deficiencies of the constructed piles which may have formed during pile construction process or may have been attributed by other activities after construction of the piles. An overview of three commonly used non-destructive tests such as sonic integrity, sonic logging and high strain dynamic load tests on deep-seated piles in Bangkok subsoil is presented in this paper. Advantages and limitations of each integrity test are discussed.

Jan 1, 2004

By Zhitao Ma

The Cast-in-place Concrete thin-wall Pipe pile, referred to as PCC pile, is a new kind of pile for soft ground improvement. In this paper, firstly, the general introductions of the new pile technique, mainly including the technique principle, the structure of pile-driving machine, and the technological process were given, then based on the results of in-situ static lateral loading test, the pile lateral capacity, the relationship of load-deflection of pile at the ground surface, the lateral deflections versus depth and the soil reaction along the pile shaft were analyzed.

Jan 1, 2006

By Alec C. Bloem

A 55' deep excavation encompassing almost a city block in London, Ontario required a lateral earth retention system to provide both temporary excavation support and a permanent groundwater cut-off wall for a proposed office complex. The system selected was an interlocking Drilled Shaft wall with 3-4 levels of tiebacks. The specifications required the system to be designed for movements or settlements around the excavation of ¼" max. Design to be by the Contractor with design parameters and a comprehensive soils report provided. An extensive system of instrumentation in the form of inclinometers and survey targets were used to monitor vertical and horizontal movements of the shoring system and adjacent properties. Introduction The project, One London Place, is a two phase office tower development in downtown London, Ontario. Phase one consists of a 24 storey office tower on the northwest part of the site, with five levels of below ground parking over the entire site "Figure 1". A second office tower will be constructed at a future date.

Jan 1, 1991

By Wen-Chieh Cheng

Two bored piles with base grouting are loaded axially and the results are used to compare with numerical analyses. One compressive pile with a diameter of 2 meters is drilled through clay deposit and into bedrock to a depth of 13.7 meters. One tensile pile with a diameter of 1.5 meters is drilled through the same clay deposit and into bedrock to a depth of 17 meters. Both piles are installed with monitoring system such as rebar strain meters, concrete strain gauges and extensometers. The monitored data during pile load test are used to obtain average frictional stress (t) a displacement (z) curve, pile tip bearing (q) as well as pile head load (p) and a displacement (s) curve. FLAC3D is used to simulate the pile loading and base grouting. The soil and bedrock are modeled with Mohr-Coulomb. The parameters of the constitutive law are established from soil biaxial tests and rock bore hole deformation tests. The pile is assumed as an elastic body. The interface element is used to simulate the pile/soil interface and pile/rock interface. The numerical results are compared with the pile load test in terms of t-z curve, q-z curve and p-s curve. Finally, the pile base grouting is simulated and the uplift is analyzed. The result from this study is promising and the numerical modeling is successful.

Jan 1, 2006

By W. D. Guo

With an experimental apparatus developed recently, model tests on piles were conducted in sand subjected to triangular soil movement profiles. Four instrumented piles tests are reported, which show the pile behavior predominantly determined by soil sliding depth. Axial load can create additional bending moment and pile deflection, which also make mode of pile-soil interaction change with sliding depth. Limiting resistance was found 1.5~3 times higher than currently used for laterally loaded piles in sand.

Jan 1, 2006

By Reinhard Gnilsen

Soil Nail walls, like any other structure, must meet high standards of design to be acceptable to the public and owners. On the other hand, the concept of soil nailing trails behind other structures in terms of defined design criteria that are commonly acknowledged. This is not to say that soil nail walls need to be less safe or less conservative than alternative more conventional concepts. Instead, the lack of established design criteria and design methodology entails that rules of thumb from past experience, overly simplified calculation assumptions, and the engineers' common sense judgement must substitute for a complex analysis of true stability and wall performance. Those "design approaches" must be conservative to ensure an adequate structure. Also, soil nailing may not be perceived prudent where site conditions are considered beyond past experience. For instance, site conditions may be perceived out-side the scope of soil nailing applicability where walls are very high, soil parameters variable or low, or nearby buildings close to the wall edge. The latter relates in particular to deep

Jan 1, 1988

By Patrick P. A. Wolfs

In the summer of 2000, the ECR®/EFT® was first introduced in the Netherlands. After the first project a field test was performed together with other geophysical methods to prove the liability of these systems and their application in areas with soft soil and high groundwater levels. The objective of this test, which was carried out with three leakage detection systems, was to locate the holes. After this test several projects have been carried out. In this article the Dutch projects "Ringvaart Aqueduct" and "Bottleneck Limburg N296/N297" are mentioned.

Jan 1, 2006

By Harry K. Weatherbee

The paper presents a design case study for a four-story correction facility addition in south Boston, Massachusetts, supported on friction piles driven into the Boston Blue Clay. 356 mm (14-in.) square prestressed-precast (PSPC) concrete piles were selected as they were found more effective and economical. A static load test was performed where the pile was brought to "failure". The load test data were evaluated to estimate the Ultimate Pile Capacity as well as the Ultimate Unit Skin Friction (Adhesion) to serve as a design tool for friction pile projects in the south Boston Area.

Jan 1, 2003

By Abhijit Saha

"Two analytical closed-form elastic-rigid-plastic solution methods to predict the rigid foundation behaviour on stone-column reinforced soil are compared, both of which takes into account the stone material yield within the host soil according to stress-dilatancy theory. These are the mechanistic methods developed by the author (2004, 2005) [that presently incorporates the dilatancy angle as per Schanz and Vermeer (1996)] and that developed by Pulko and Majes (2006), that takes into account the column yield as per Rowe dilatancy theory. Since optimal design of stone column necessitates optimum stress concentration on column, which is generally composed of dense gravel with/or without sand, the vertical stress on granular column is often close to its peak strength and the material dilates. To arrive at closed-form analytic solution to this complex soil-stone column interaction problem, some common assumptions like axi-symmetric soilstone column ‘unit-cell’, elastic host soil and rigid-plastic Mohr-Coulomb stone column material are combined with equilibrium and kinematic conditions. The results reflect the beneficial effect of dilatancy within the optimal range or techno-economic domain of area-ratio. The settlement predictions are compared with other analytical methods available in literature as well as with measured settlement reduction of stonecolumn reinforced ground at different subsoil conditions around the globe reported in literature.INTRODUCTIONStone columns or granular piles are frequently used in stabilization of soft clays, silts and loose silty-sands with large amount of fines. The majority of analytical methods assume infinitely wide loaded area with end-bearing columns having constant diameter and spacing that approximate to axi-symmetric conditions, and the approach is known as ‘unit-cell concept’. Several analytical solutions are available, and many of them (Aboshi et al; 1979, Balaam & Booker; 1981) are based on elastic approach considering the stonecolumn and surrounding soil as elastic materials. However, elastic methods give the ratio between the vertical stress in the column to soil (stress concentration factor) approximately equal to the ratio of constrained modulus of both materials. This ratio was found to be considerably higher than measured in the field and it is believed that elastic methods may overestimate the effects of stone columns on settlement reduction (Barksdale & Bachus, 1983). The elastic and elasto-plastic solutions presented by Balaam and Booker (1981, 1985) indicate that the problem can be idealized by assuming that the stone column is in a triaxial state and possibly yielding, such that there is no shear stress at the stone-soil interface and no yielding in the soil. Similar assumptions of stone column to be in a state of limiting equilibrium and under a triaxial stress state are considered in other methods also (Priebe; 1976, Van Impe & De Beer; 1983, Van Impe & Madhav; 1992, Saha & De; 1994, Saha; 2004, 2005, Pulko & Majes; 2006). In majority of the methods it is assumed that under load the stone-column yields at constant volume. However, the last three cases cited consider another parameter; the dilation of stone column. In Van Impe and Madhav’s (1992) and author’s (2004, 2005) method, the dilation is taken into account through the final value of the volumetric strain of column, whereas Pulko & Majes (2006) considered the stone column as Mohr-Coulomb rigid-plastic; dilating at yield in line with Rowe (1962) dilatancy theory."

Jan 1, 2015

By D. V. Karandikar

Contiguous bored piles have been used in the past for retaining the sides of deep excavation. An innovative version of this method was adopted successfully in two prestigeous projects in Bombay in which in a very constricted and congested locality, adjoining seashore at Walkeshwar, 14 m deep excavations with vertical sides were required. 600 mm dia bored cast-in-situ piles were first installed at 1.2 m c/c and subsequently as the excavation proceeded, they were tied to cast-in-situ RCC waling beams. The shear connectors to the beams were pre-fixed to the pile reinforcing cage at specified depths. The pile / waling beam system was anchored into the ground by installing inclined prestressed cable anchors at the designed depths. The waling beams were also used to support the brickwalls, which formed the required backup wall for fixing the tiled water proofing system. Catch-drains were installed behind the brickwalls for relieving the ground water pressure and thus ensuring a very economic design. The adequacy of the system was proven in that where the system was not installed in time, failure of the sides occurred during monsoon. Whereas in the areas where the above retaining system was installed, there were no problems inspite of heavy monsoon and surcharge of construction materials and equipment. The system became a very effective and economic alternative to an anchored diaphragm wall. The paper presents the case studies of these two projects.

Jan 1, 1996

By Xiong Houjin

In the excavation works of some deep foundation pits within the boundaries of Guang­dong Province of China, though some measures, such as steel sheet piles, diaphragm walls, etc. were taken to protect the walls, the construction of the excavation works was often accompanied by damage of buildings and public facilities, surface settelment. sand boil and collapse of piles. When these happened, only chemical grouting could be used as the most efficient measure for rushing to deal with or rescue the emergencies. Besides, the application of chemical grouting protection wall technique also palys a very important role under the geologic conditions of the coastal areas of Guangdong Province, when applied in the mucky oystershell layer wealthy in water and the deep mud layer, it can not only achieve good results, but also reduce the cost significantly. In this paper, we discuss the water-tight and earth retaining functions of chemical grouting protection wall in weak formation, and introduce the applicable ranges of chemical grouting protection wall in the excavation of deep foundation pits. Some technological principles and design considerations of the construction of chemical grouting protection wall are presented. Different types of protection wall are also introduced.

Jan 1, 1991

By Cassandra A. Wetzel

Rock socketed mini-piles are a desirable foundation alternative when design capacity is more than 40 tons and there is limited access. In this case history mini-piles were designed to support between 75 and 200 kips at 12 locations adjacent to a perimeter wall, a party wall and at cast iron column piers. Limited geotechnical information, low overhead clearance, and active building population tested the creativity of the team to get the piles installed. The key geotechnical concern during installation of the mini-piles was the presence of a glacial till layer above the bedrock surface that restricted the seating of the casing into bedrock with a track mounted drill rig. Soil loss during the advancement of the rock socket using an air hammer was excessive and increased the risk of subsidence. Over a three week period the engineer worked with the contractor to modify the design, means, methods, and materials to install piles with adequate load capacity. This paper will present the changes in design and construction methods that were required.

By Geoffrey Birch

A skilled and efficient workforce is a pre-requisite for the success of modern construction companies. The drive for improved performance, innovation and best value must be matched by the enhanced skills of the construction personnel. Training has been accepted as one of the essential cost effective elements to achieve these goals. The foundation industry demands particular specialist skills and requires focused training for its dedicated operatives. The introduction and development of specific training qualifications for the foundation sector is providing significant benefits.

Jan 1, 2000