Search Documents

By Athena C. Denivo, Pablo V. Lopez, Michael McMaster, Sissy Nikolaou, Alfred H. Brand

"The paper presents the history of development of the United States Tennis Association (USTA) site, focusing on geotechnical, geoseismic, and foundation engineering challenges associated with it. The site is located at the Flushing Meadows Corona Park area of Queens, New York. Now home to the Billie Jean King National Tennis Center (BJKNTC), the site used to be a biologically rich, tidal salt marsh that extended south from Flushing Bay and overlaid an ancient buried valley. In early 20th century, Brooklyn Ash Co. was contracted to fill the marshland with cinders and furnace ashes. F. Scott Fitzgerald describes the “Valley of Ashes” as “a fantastic farm where ashes grow like wheat into ridges and hills and grotesque gardens; where ashes take the forms of houses and chimneys and rising smoke, and finally, with a transcendent effort, of ash-gray men who move dimly and already crumbling through the powdery air.” In 1939 the site was leveled and filled to host the World’s Fair and refilled again for the 1964 World’s Fair.The USTA moved to the site in 1978 and in mid-1990’s constructed the 23,000-seat Arthur Ashe Stadium (AAS). Currently, USTA has a Strategic Vision Plan venue with several interconnected construction projects including buildings, infrastructure upgrades and improvements to site circulation. In addition to a historical walkthrough, the authors will discuss technical challenges of supporting these developments through layers of fill, thick organic silty plastic clays and regional varved soils with bedrock found 300 to 400 feet deep. The subsurface is not only a weak foundation medium, but is susceptible to large amplification of seismic waves propagating from the bedrock during earthquakes. The developments are usually founded on project-specific pile foundations that carry static loads in deeper layers and accommodate lateral demands and performance objectives. Engineering innovations from the most recent development, the roof structure over AAS, will be discussed."

Jan 1, 2016

By Damir Dedic, Wörle. Patrick

"Soil properties within a construction project area are analyzed during the planning phase. However, it is only possible to achieve selective soil exploration, even in the case of very extensive investigatory programs, which results in a certain soil risk and uncertainties for planning and execution.Therefore, the application of monitoring systems is becoming increasingly important in the field of geotechnics. The application of suitable monitoring systems for these particular purposes provides considerable knowledge relating to the load bearing behavior of the soil and the ground anchor. Applications that present major challenges to measuring anchor forces include back-anchorages of long-lasting and very deep construction pits, construction pits in urban areas, slope and embankment supports for track and vehicular routes, port and lock structures, and uplift control. Apart from overseeing individual construction stages, monitoring systems analyze the interaction between the soil and structure throughout the latter’s entire life cycle and safeguard the functional capability of the applied system components. Geotechnical construction projects can be adapted, optimized and carried out with enhanced safety from the information obtained.Conventional Monitoring SystemsThere are numerous approaches for determining anchor forces of bar or strand anchors. Lift-off tests and measurements with load cells are the most common methods.Lift-off Test: Lift-off tests provide a possibility to monitor the prevailing force in strand or bar anchors. The entire anchor head structure is lifted using the appropriate equipment. The steel tendon is prolonged, or in the case of strand anchors, a screw-on cap holds the wedge carrier so that a tensioning jack can be mounted above it. Then, the tendon is prestressed until the lower anchor nut (bar) or wedge carrier (strand) is lifted off from the anchor plate. The intersection of the two straight lines in the figure represents the force at which the anchor nut or the wedge carrier lifts off from the anchor plate. Thus, the intersection displays the actual load of the anchor. This form of anchor force control gives conclusive results, but at the same time requires extensive accessories and extra personnel to execute the test. For this test, a sufficient bar overhang must be available, the wedge plate must possess an external thread, or there must be a strand overhang of at least 24 in (60 cm). Furthermore, the anchor head must be freely accessible and in a position to be reached with the necessary equipment."

Jan 1, 2017

By Kalyani Devabhaktuni, Mike Minton, Mark T. Howe, Yan Zhang

During the procurement phase of a Design-Build (DB) project, design-build contractors must often commit to a fixed price based on limited or incomplete geotechnical information. This lack of information can result in an inaccurate assessment and allocation of project risk to either the contracting authority or the DB contractor. This paper presents a case study of an elevated water tank supported by mixed ground improvement techniques, including Vibro-Compaction (VC), Aggregate Piers (AP) and Compaction Grouting (CG) in East St. Louis, Illinois. An adaptive design and contracting approach provided the best value solution for a complicated set of geotechnical problems, including static bearing capacity and settlement concerns as well as liquefaction induced settlement. Close cooperation between the owner, the tank contractor, the geotechnical engineer and the ground improvement contractor was essential to produce an effective solution. Ground Improvement techniques resolved the geotechnical challenges at the site through adaptive design methods, utilizing progressive rounds of verification and real time data acquisition to achieve performance objectives. This paper details the evaluation of geotechnical criteria, the selection of ground improvement techniques, the adaptive design and implementation of ground improvements, as well as contracting methodologies used to ensure that the best value was provided. PROJECT INFORMATION In November, 2016, CB&I Storage Tank Solutions (McDermott) submitted a design/build proposal for an elevated water tank for Illinois American Water Company (IAW) in East St. Louis, Illinois. The purpose of this tank was to have backup water capacity for power generation. In the RFP, IAW requested two alternate styles of tank: Option 1, a 1250 Million Gallon (MG) Composite Elevated Tank or Option 2, a 1250 MG Waterspheroid tank. Option 1 consisted of a steel tank supported on a concrete tower. Option 2 consisted of a steel tank supported on a steel shaft. The height (determined by IAW) was 140 feet to the top capacity line measured from top of floor slab.

Jan 1, 2019

By Louay Owaidat, Daniel Jabbour, Allan Frappier, Jose Gomez, Mark Stanley, Tino Maestas

The U.S. Army Corps of Engineers (USACE) is implementing a levee strengthening program along the Sacramento River East Levee (SREL) designed to correct 11 miles of deficient levees as identified by recent hydraulic and geotechnical investigations. The first project, the subject of this paper, completed in 2020 resulted in approximately 3.0 miles of improvements to the California Central Valley Flood Protection system. The project area lies along the east bank of the Sacramento River in Sacramento. The program consists of constructing cutoff walls through existing levee embankments to remediate levee through seepage and under-seepage. Key challenges included designing and constructing measures to remediate a 100-year-old legacy levee system, the presence of both industrial and residential properties immediately adjacent to the landside of the levee creating severe space and access limitations, and performing this work during the 2020 statewide mandate to shelter-in-place due to the COVID-19 pandemic. The project team of contractors, USACE, state and local agencies, and engineering firms partnered to bring this project to successful completion within budget and on schedule expending more than 60,000 man-hours with no lost time accidents. With the issuance of future planned contracts, the program will significantly reduce flood risk to the City of Sacramento.

Sep 8, 2021

By William D. Oder, Seth H. Hamblin, Les R. Chernatskas, Jonathan L. Ernst

Large diameter drilled deep foundations are a widely utilized solution throughout North America and the world. Numerous design and construction techniques developed over the past 100 years have made this type of foundation a robust, reliable, and efficient foundation option to support a wide variety of structures. From bridges, to marine structures, to high-rise buildings, drilled shafts are a time-tested approach for all types of infrastructure projects. Yet, what remains ambiguous in the current state of engineering practice is how to respond when a shaft is constructed that, for potentially different reasons, may or may not meet the design requirements? In this case, what are the best practices for Contractors and Engineers when a structural, geotechnical, or material integrity issue arises during construction? In our experience the answers to these questions are not widely known, but are profoundly important so that engineers can have tools available to confidently and efficiently address concerns, and provide a path forward for the project. This paper seeks to answer the above questions by presenting details of different remediation approaches using the results of several case studies where structural and geotechnical engineering methods, combined with non-destructive integrity testing (NDT), were employed to evaluate the acceptance of “questionable” drilled shafts. Through multidisciplinary techniques like Cross-hole Sonic Logging and 3-D Tomography which enhance the resolution of anomalous zones and defects in concrete, the development of concrete strength estimates from non-destructive testing data, and executing innovative structural and geotechnical analyses to evaluate the as-built conditions, drilled shafts that might have historically been rejected were ultimately accepted by the project team. This paper presents a series of unique case studies that together depict a roadmap for a comprehensive approach to reliably evaluate and guide the industry to address these types of drilled shaft construction issues.

Oct 1, 2022

By Luca Pingue, Regine Jagow-Klaff, Franco Muratore, Carlandrea Albonico, Damiano Frontini, Rudolf Wernecké

This paper describes an artificial ground freezing (AGF) application carried out to ensure both watertightness and structural support for the safe excavation of four cross passages of the Forrestfield Airport Link (FAL) project in Perth. The line will deliver 8.5 km extension of the existing urban rail network connecting the growing eastern suburbs of Perth with the existing suburban rail network. The proposed soil improvement technique is adopted as a smart alternative to jet grouting from the surface since the use of heavy equipment with long vertical mast was not allowed due to the line underpassing an airport in operation. In this paper, details of the challenges and lessons learned during both design and construction phases are given. Furthermore, it is described the geometry and the installation of freeze pipes in presence of a massive steel frame, ventilation system and slurry pipes of the tunnel boring machine (TBM) in operation. It is also illustrated the web monitoring system to allow key personnel to follow in real time the development of soil temperatures, tunnel convergences and ground surface deformations as well as changes in the interaction between international parties involved due to the COVID-19 pandemic.

May 1, 2022

By Liiban A. Affi

The most difficult task of designing multilevel tieback walls for deep excavation support is the determination of lateral stresses. These lateral stresses act not only on the shored height, but also on the embedded portion of the soldier pile, all the way down to the pile tip. Examples of lateral stresses include uniform surcharge load (soil spoils or equipment), strip load surcharge from Cooper E80 (train loads), line load surcharge (exterior footing or retaining walls), and point loads (cell tower). In this paper we will discuss the various surcharges, do step by step example calculations and show how to take the total lateral stress output and present the design pressures for direct use by the substructural designer. Included is a case study from a project Anaheim Hills, California, USA.

Jan 1, 2010

By Jim Rix, Ken Been, Nihal Bohra, Anthony Rice, Juan Lopez

"A temporary bridge, supported on steel pipe piles, was built to expedite the construction of a breakwater structure off the western coast of Peru. The bridge provided access for dump trucks to the breakwater across a 342 m (1122 ft.) wide navigation channel from a liquefied natural gas (LNG) loading facility, at the end of a 1.3 km (0.82 miles) long permanent trestle, in 15 m (50 ft.) water depth. After the completion of the breakwater, the temporary bridge was removed, and the piles were extracted approximately one year after the initial driving. The bridge deck was typically supported on pairs of 914.4 mm (3 ft.) diameter, 18 mm (0.708 inch) wall steel pipe piles spaced at 7.5 m (24.6 ft.) across the bridge width and 18 m (60 ft.) along the bridge length. In an attempt to reduce the driven pile embedment, an inner closure plate was installed at 2.7 to 7 m (9 to 23 ft.) from the pile toe to force closed-end behavior. The piles were designed to carry 3400 kN (383 tons) axial compression load, and a minimum of 8 m (26 ft.) embedment was specified to provide sufficient resistance to the lateral loads.The subsurface conditions consisted of cemented conglomerate of sand, gravel, pebbles and some boulders, locally known as the Cañete Formation. The driven pile embedment varied widely, between 8 to 24 m (26 to 79 ft.). A significant portion of each pile was above the seabed, passing through seawater and up to the bridge deck, and was therefore unsupported. The extraction of the piles was challenging due to the subsurface conditions, presence of significant water column, pile weight, and the inner closure plate. Several different approaches were attempted before the piles could be successfully extracted. This paper summarizes the difficulties encountered and observations made during the driving and extraction of these piles."

Jan 1, 2017

By Nihal Bohra

A temporary bridge, supported on steel pipe piles, was built to expedite the construction of a breakwater structure off the western coast of Peru. The bridge provided access for dump trucks to the breakwater across a 342 m (1122 ft.) wide navigation channel from a liquefied natural gas (LNG) loading facility, at the end of a 1.3 km (0.82 miles) long permanent trestle, in 15 m (50 ft.) water depth. After the completion of the breakwater, the temporary bridge was removed, and the piles were extracted approximately one year after the initial driving. The bridge deck was typically supported on pairs of 914.4 mm (3 ft.) diameter, 18 mm (0.708 inch) wall steel pipe piles spaced at 7.5 m (24.6 ft.) across the bridge width and 18 m (60 ft.) along the bridge length. In an attempt to reduce the driven pile embedment, an inner closure plate was installed at 2.7 to 7 m (9 to 23 ft.) from the pile toe to force closed-end behavior. The piles were designed to carry 3400 kN (383 tons) axial compression load, and a minimum of 8 m (26 ft.) embedment was specified to provide sufficient resistance to the lateral loads. The subsurface conditions consisted of cemented conglomerate of sand, gravel, pebbles and some boulders, locally known as the Cañete Formation. The driven pile embedment varied widely, between 8 to 24 m (26 to 79 ft.). A significant portion of each pile was above the seabed, passing through seawater and up to the bridge deck, and was therefore unsupported. The extraction of the piles was challenging due to the subsurface conditions, presence of significant water column, pile weight, and the inner closure plate. Several different approaches were attempted before the piles could be successfully extracted. This paper summarizes the difficulties encountered and observations made during the driving and extraction of these piles.

By Arash Khosravifar, Nason McCullough, Stephen, Milad Souri, Scott Schlechter, E. Dickenson

The results of five centrifuge models were used to evaluate the response of pile-supported wharves subjected to inertial and liquefaction-induced lateral spreading loads. The centrifuge models contained pile groups that were embedded in rockfill dikes over layers of loose to dense sand and were shaken by a series of ground motions. The p-y curves were back-calculated for both dynamic and static loading from centrifuge data and were compared against commonly used API p-y relationships. It was found that a significant reduction in ultimate soil resistance occurred in dynamic p-y curves in partially/fully liquefied soils as compared to static p-y curves. It was also found that incorporating p-multipliers that are proportional to the pore water pressure ratio in granular materials is adequate for estimating pile demands in pseudo static analysis. 1. INTRODUCTION Liquefaction-induced ground deformations can cause severe damage to pile-supported wharves and other waterfront structures. A common approach in analyzing the lateral behavior of piles against seismic loads is using the beam on nonlinear Winkler foundation (BNWF) or p-y spring analysis. One common p-y relationship for sand is the one proposed by the American Petroleum Institute, also known as the API sand model (API 1993). While the API sand model was originally developed for the static loading conditions, it is common to modify the API sand curves for the effects of cyclic loading. However, there is no consensus on how to modify the static p-y curves for the effects of liquefaction and pore water pressure generation in loose granular soils. In previous studies, p-y springs of piles in liquefying soils were back-calculated from case histories, centrifuge model studies (e.g., Wilson et al. 2000; Brandenberg et al. 2005; Abdoun et al. 2003), full-scale tests (e.g., Rollins et al. 2005; Chang and Hutchinson 2013), and numerical analyses (e.g., McGann et al. 2011). In general, these studies found the softening effects of soil liquefaction on p-y curves, as well as a hardening behavior attributed to the dilative response of the liquefied soil around the pile. However, these studies provide varying recommendations on how to modify the static p-y curves to capture this complex behavior. Some design guidelines propose softening the static p-y curves using p-multipliers (e.g., Caltrans 2012). Other studies propose an upward concave shape for p-y curves in liquefied soils (e.g., Franke and Rollins 2013; Chang and Hutchinson 2013).

Jan 1, 2019

By M. D. Riegel, P. B. Pizzimenti, E. M. Zamiskie, Britain A. Materek

"The Skanska/Kiewit/ECCO III team (SKE) in association with HNTB was awarded the design-build contract for Phase I of the Kosciuszko Bridge Replacement Project. As lead designer for the SKE team, HNTB was responsible for the design of the Brooklyn Connector which includes construction of approximately 2000 feet of new staged earth-filled embankments utilizing prefabricated modular retaining walls (T-Walls®). The proposed embankments will be constructed adjacent to and beneath the existing Brooklyn Queens Expressway (BQE) viaduct while the existing viaduct remains in service. Critical aspects of the settlement assessment relating to the soils supporting the existing BQE will be addressed, as their behavior drives the deformation of the viaduct. Furthermore, a construction monitoring program was used to enable the designer to assess settlement predictions and allow SKE to mitigate potential impacts to the existing BQE during construction. Additionally, the methodology for installation of the embankments in a limited access area underneath an active viaduct supported on settlement sensitive shallow foundations will be presented.INTRODUCTIONSkanska-Kiewit-ECCO III Joint Venture, in association with HNTB was contracted by the New York State Department of Transportation (NYSDOT) to design and construct the Phase 1 replacement of the Kosciuszko Bridge Design-Build Project. Phase 1 of the project involves the design and construction of the new eastbound structures of Interstate 278 over Newtown Creek from Brooklyn to Queens. The project runs between Morgan Avenue in Brooklyn and the Long Island Expressway Interchange in Queens (approx. 1.1 miles) and includes the staged demolition of the existing structures."

Jan 1, 2016

By Richard J. Hartman

This presentation identifies some of the more common problems associated with cofferdam construction. After the various problems are identified, they are briefly explained and possible solutions and preventive measures are noted. Photographic slides used during the seminar illustrate the conditions. This discussion is limited to cofferdams which are braced structures excavated inside to allow access for construction. The common procedure is to drive sheet piling and then alternatively install bracing and excavate. They can be located either on land or in water. Loads are applied by soil, water, surcharge pres-sure, eccentricities, and impact loads. The loads are resisted by the sheet piling, the bracing, and the soil below the bottom of the excavation; each of these three components must be capable of resisting the applied loads.

Jan 1, 1987

By M. Krzaninski, Y. Zou, A. Frost

The foundation solution for a data centre building in Sydney, Australia comprised two alternatives, the first of which incorporated the use of CFA piles founded in rock at approx. 27m depth to support column working loadings of approx. 7.5MN, and the second utilising rapid impact compaction with a raft foundation of 1.0m thick concrete slab. Soil conditions comprised 1m of fill over 3 to 4m of sands varying from loose to dense consistency, underlain by very stiff clays overlying the rock. A creative solution incorporating Rapid Impact Compaction to improve the loose soils in conjunction with a piled raft solution was proposed. Piles proposed under the raft were Atlas Drilled Displacement piles which offered advantages of displacement pile performance and savings in time and material costs. The piled raft solution was developed in consultation with the consulting structural engineer, combining the skills of the piling contractor and consulting engineer to the benefit of the project. This paper describes the development and design aspects of the piled raft solution adopted for the project.

Nov 1, 2022

By Patrick J. Hannigan, Frank Rausche, Rozbeh B. Moghaddam

The Top-Loaded Bi-Directional Test (“TLBT”) is a new method to apply bi-directional loads to a deep foundation element with the loading source located above the foundation head. In the TLBT reusable load assembly, loads are applied to the foundation using the R-System which consists of two stacked steel plates located at the geotechnical resistance balance point or at the foundation base connected to the load assembly via vertical elements. The top plate or the Shaft Bearing Plate (“SBP”) will transfer loads to the foundation upper portion, and the bottom plate or the Base Bearing Plate (“BBP”) will transfer loads to the foundation lower portion as well as the foundation base. At the surface, above the foundation head, a hydraulic jack is located between a Top Load Assembly (“TLA”), and the Bottom Load Assembly (“BLA”). The TLA and BLA are connected to vertical elements which are consequently connected to the R-system. As the jack is pressurized and expanded at the surface, the R-System plates are separated, and the foundation is bidirectionally loaded. This paper presents a brief description of the conventional Bi-Directional Load Test (“BDLT”) including benefits and limitations followed by the TLBT method introduction including its benefits and advantages over other testing methods.

Sep 8, 2021

By Ting Chinsu

Diaphragm wall with tie-back cable is widely used for deep excavation, especially in the area with high density of buildings. This paper presents the measured earth pressure distribution on diaphragm wall during excavation. The earth pressure cells used in field were successfully installed in deep slurry trench by a new type of simplified manipulator. The sizes of the deep excavation are 26m X 36m on plane and 9m in depth. The construction site is located between two multistorey buildings at the main business section of Beijing city. In this paper the field measurements of earth pressure distribution and the analyses based on the comparison between calculation and measurement are very valuable to improve the current calculation method for diaphragm wall design.

Jan 1, 1991

By Rakam Lama Tamang, Michael J. Byle, Stephen Ernst

"For various reasons, dredging may become necessary in front of existing bulkhead walls, either for channel deepening or for environmental remediation of contaminated sediments. The removal of sediments at the base of bulkhead walls removes support for the toe of the wall that must be assessed. Evaluation of this impact can be problematic for aging bulkheads for which no design or construction records exist. This paper will address the steps that should be taken in investigation and analysis to assure proper assessment and means to address uncertainties and gaps in information. The steps include pre-investigation data review, field inspection, geotechnical and geophysical investigation tools, parametric analysis and design tools. Examples from several bulkhead assessment projects will be provided that include a variety of conditions and tools for application. The focus of the paper will be on the integration of technologies to assess bulkhead geometry, geotechnical properties and stability, structural safety and constructability issues with removal of support, and means of temporary and permanent stabilization for environmental applications.IntroductionBulkheads and quays have existed as long as there have been waterfront activities. Some of the earliest date back to 1200 B.C.E.(Raban, 1987), however in the United States few predate the eighteenth century. Most extant bulkhead structures, and all steel sheet pile bulkhead walls date from the early 20th century or later. These structures function to protect the shore from erosion, support landside activities, and serve as place to moor and offload vessels. Regardless of the age or usage of existing bulkheads, it is essential to assess and protect them if needed where removal of soils on the water side of the bulkheads is planned to dredging.Waterfront BulkheadsExisting bulkhead structures can be classified into two types: Cantilevered, and anchored. Cantilevered walls are completely supported by the soil on the water side, while anchored bulkheads are supported both by the soil on the water side and anchorage on the land side (Figure 1). Walls may be constructed of timber, steel, or concrete. Timber walls may be lagging with soldier piles, cribbing with soldier piles, or timber sheeted such as Wakefield walls (Figure 2). Steel bulkheads are most commonly constructed using sheet piling comprised of interlocking A or Z shapes, though some historic walls were constructed with flat sheets. Precast concrete sheet piling has also been used in construction of bulkhead walls. Anchorage may be provided by steel bars or tendons attached to deadmen, sheet piling, driven piles, or earth anchors."

Jan 1, 2017

By Patrick J. Hannigan, Seth Robertson, Rozbeh B. Moghaddam

The Top-Loaded Bi-Directional Test (―TLBT‖) and the conventional Bi-Directional Load Test (―BDLT‖) are full-scale static load test methods. In both methods, the test loads are applied bi-directionally to the deep foundation. The advantages of the conventional BDLT have been well established for cost efficient static load testing of deep foundations, particularly for large diameter, high-capacity drilled foundations. A conventional BDLT applies the bi-directional test loads using an embedded jack and bearing plates. The TLBT method also applies the bi-directional test load to embedded bearing plates but does so using reusable high-strength threaded bars attached to an above-grade hydraulic jack and load transfer assembly. The new TLBT method is well suited for load testing shafts of a moderate diameter, length, and nominal resistance or ultimate load. TLBT advantages include economic considerations resulting from the method’s reusable load application components and constructability considerations as it readily accommodates a center concrete tremie pipe or pump line location. This paper presents comparison results from full-scale load tests performed using both bi-directional load testing methods. Adjacent 3-foot diameter by 30-foot long BDLT and TLBT shafts were tested. Details regarding subsurface conditions and test shaft construction are included for the comparison of the TLBT and BDLT results. Corresponding test data and analyses for both test shafts are presented and discussed in detail. The BDLT shaft had a maximum uni-directional load of 240 kips at upper and lower bearing plate displacements of 0.5 and -3.8 inches, respectively. The TLBT had a maximum uni-directional load of 300 kips at upper and lower bearing plate displacements of 1.0 and -5.9 inches, respectively. These results as well as the load-transfer behavior and equivalent top loading curve results from the adjacent BDLT and TLBT drilled shafts are discussed. The paper also discusses the strain gage instrumentation on the TLBT load application bars and on the embedded bearing plates.

Oct 1, 2022

By Piotr Kozlowski, Stanley L. Worst, Matthew J. Niermann

Circular secant pile shafts were installed along the tunnel alignments for both the Ohio Canal Interceptor Tunnel project in Akron, Ohio and the Ohio River Tunnel project in Louisville, Kentucky. The diameters ranged from 34 to 51 feet and the depths ranged from 49 to 107 feet. Verticality and concrete volumes were measured on all piles to verify compliance with the design, which for some shafts consisted of a finite element model with multiple openings using unreinforced concrete secant piles. All secant piles were drilled into rock to seal off the groundwater. This paper will discuss the design, construction and quality control of the secant piles for these projects. INTRODUCTION Many Midwest and Northeast cities have Combined Sewer Overflow (CSO) systems which discharge pollutants into waterways during wet weather events. One way to remedy this issue is to provide a temporary overflow tunnel. A temporary overflow tunnel connects to the combined sewer system and collects the overflow during wet weather events, storing the wastewater until the event has subsided. After the storm event, the stored wastewater can be pumped to the treatment facilities and processed as normal. Project Background – Akron, OH The Ohio Canal Interceptor Tunnel (OCIT) project was performed as a result of the Environmental Protection Agency’s (EPA) Consent Decree with the City of Akron, Ohio. This Consent Decree required modification of the existing Combined Sewer Overflow system. The resulting project consisted of a 27- foot diameter tunnel with multiple points of entry to capture the sewer overflow and prevent it from entering waterways. The tunnel is over 6,000 feet long and is as deep as 150 feet below the ground surface; see Figure 1 below.

Jan 1, 2019

By Howard A. Perko, Margaret Dring, Gerald Verbeek, Scott Slaughter

Helical piles have become a widely used deep foundation system in recent years due to their many inherent advantages. The cone penetration test (CPT) is commonly used in geotechnical practice to evaluate subsurface conditions for deep foundation design as the method provides a continuous soil profile in a short amount of time, measures in-situ soil strength, and in many ways behaves similar to a “mini pile” during penetration. In the CPT test, an instrumented cone is hydraulically advanced into the soil at a constant rate. As the cone is advanced, strain gauges embedded in the cone body continuously measure the tip resistance and side friction. In addition, a piezometer element is commonly used to measure the (dynamic) pore water pressure in the soil as the cone is advanced. A study was conducted comparing the CPT tip resistance to helical pile installation torque and capacity. In this paper, the outcome of this study was compared with historical data of helical pile installation torque records, static analysis predictions using commonly used techniques, and pile load test results over a wide range of soil conditions. A literature review was also conducted where a comparison was made for CPT tip resistance and helical pile installation torque data with previously published correlations.

Sep 8, 2021

By Melinda J. Hummel, Zachary T. Smith, Nathaniel Witter, Nina F. Carney

The revitalization of Pittsburgh’s historic Strip District has led to the redevelopment of existing properties and the development of new properties. At one time, the Strip was home to wholesale market products. Now, the historical warehouse buildings are being converted to multi-use residential and commercial properties. One such property, 1600 Smallman Street, consisted of 1 to 6-story connected buildings that housed night clubs, retail shops, and office space. The lower story portion of the building, on the southwest side of the property, was torn down to make room for a new 5-story- parking garage with street level retail space. The remaining 6-story-building, on the northeast, was gutted to be renovated into high-end condominiums, keeping the exterior historical building facade.