Search Documents

By Erwin Stötzer, Renato Fiorotto, Wolfgang G. Brunner, Manfred Schöpf

"Deep mixing methods can be used economically for the construction of cut-off or excavation support walls where other systems such as traditional soldier beams and lagging walls would yie ld unsatisfactory performance, where the installation of vibrated or driven sheet piles could cause vibration induced settlements and where concrete diaphragm walls would be time consuming and expensive. The new CSM method can largely replace the more conventional single or multiple auger methods of soil mixing or jet grouting. The cutter tool is similar to a cutter used in diaphragm walls or cut-off walls and is operated with a Kelly mounted on a drill rig. With this system much deeper walls can be installed and even hard soil layers can be penetrated. CONVENTIONAL SOIL MIXINGIn 1962 Norman Liver patented an auger-based soil mixing technique that has become the basis for the world's current technology.The deep mixing method (DMM), as it is known today, is an in situ soil treatment and improvement technology where the soil is blended with binders and/or other materials that are introduced in a slurry or dry form.Typically one or more hollow, rotating mixing shafts tipped with some type of cutting tool are mounted vertically to the mast of a base carrier and are driven into the ground by hydraulic or electrically powered rotary heads. The shafts above the cutting tool may be further equipped with discontinuous auger flights and/or mixing paddles. The binder is injected through the hollow shafts to nozzles located near the cutting tool where it is mixed with the ground to form columns of treated soil.Individual column diameters range from 0,6m to 1,5m and may extend to 40 m in depth. They can be arranged individually or in contiguous or secant patterns to produce a wide range of treated soil structures on both land and marine projects. Typical configurations are: Single elements, rows of overlapping (secant) elements, grids, lattices and blocks (Fig. 1 )."

Jan 1, 2005

By Ahmad Mahboubi

The damage caused by catastrophic earthquakes has always been an incentive towards more sophisticated building codes and requirements. In parallel to computer technology development, the engineers? attitude towards acquisition of more accurate results is increasing. This approach leads to designation of structural elements with more elaboration considering different aspects of their behavior. In addition, less simplified methods will be considered as satisfactory for analyzing such problems. The problem of soil-pile-structure interaction is one of the phenomena that can be included in this category. In general, there are two methods by which the study of soil-pile interaction phenomenon is studied. These include direct and sub-structuring methods. The sub-structuring approach relies on the linear or slightly non-linear behavior of soil since it employs the results of kinematic interaction analyses for inertial interaction studies. In the past, the kinematic interaction between pile-soil was considered as negligible. This was due to the softer nature of the surrounding soil that increased the time period of vibrations. However, more research revealed that although this approach was consistent in many cases, there were some sites where the time period decreased. This was due to the material properties of the foundation and the soil, in a way that caused the frequency of vibration meet natural frequency of the system. The second type of interaction is the inertial interaction which reflects the effect a structure on top exerts on the oscillation experienced by the foundation. This paper examines the impact of vertical load on the inertial interaction by virtue of impedance functions. Three different load cases for the structure at the top of a pile foundation were considered for the analyses conducted in this study. The changes in the stiffness and damping of the system by frequency are studied and finally, the results are presented.

Jan 1, 2010

By Yazen Khasawneh, Osvaldo P. M. Vitali, Mohammad Nassim

Wind turbines are subjected to complex form of cyclic loadings with variable amplitudes and frequencies. The cyclic loading and the accumulation of plastic strains with the number of cycles will result in degradation of the foundation soil stiffness. The foundation stiffness degradation will result in a shift (reduction) of the fundamental frequency of the wind turbine. Although this issue is recognized in the guidelines for wind turbines foundation design, no specific provisions are provided in the guidelines to consider the long-term stiffness degradation. In this paper, a practical procedure to consider the long-term cyclic loading effects on the stiffness of wind turbine foundations in cohesive soil is proposed. The procedure is based on 3D FEM modeling and reliable empirical methods to estimate the stiffness degradation due to the cyclic loading. Using the proposed procedure, the long-term performance of the P&H tensionless pier foundation with and without a reinforcing collar at the top of the pier is assessed. The numerical results demonstrated that the long-term performance of the P&H tensionless pier foundation with a reinforcing collar at the top of the pier is outstanding with negligible long-term degradation of the foundation stiffness.

Sep 8, 2021

By Jr NeSmith

"Augered-cast-in-place (ACIP) pile installation technology has matured extensively since the first auger, pressure grouted pile was patented in 1959. The current technology allows for successful pile installation across a variety of stratigraphies to meet various project load resistance requirements. This paper presents an overview of current ACIP techniques by comparing a number of case histories in a variety of geologic settings from Eastern Pennsylvania, New York City and New Jersey to demonstrate ACIP pile constructability in soft soils as well as the penetration, and resulting significant loads resisted, of ACIP piles in dense soils and intermediate geo-materials. Geologic settings that will be discussed include the Piedmont and Coastal Plain geologic provinces as well as glacial till deposits. Keywords: Deep Foundations, Piles, Augercast, Augered-cast-in-place, Auger pressure grouted, ACIP, APGINTRODUCTIONThe author, along with two colleagues, published an article in Deep Foundations magazine (NeSmith et al, 2013) which described a number of the advances in equipment, techniques, installation monitoring and post-construction testing that have expanded the geologies in which Augered Cast-in-place (ACIP) piles are installed as well as increasing their efficiency in some traditional ACIP pile geologies. The author uses the term efficiency to refer to the load resisted by a pile of a certain diameter and the increased efficiency noted refers to increased allowable loads over those traditionally resisted by piles of certain diameter (or a reduction in pile diameter from that which was traditionally used to support a certain design load). The performance and installation of ACIP piles in a variety of geologies in the Northeastern U.S. are discussed herein.PIEDMONT PHYSIGRAPHIC PROVINCEThe Piedmont physiographic province stretches from Alabama to the east through Georgia and up the east coast, just west of the Coastal Plain to Pennsylvania and New York (Brown, 2002). It generally consists of soils weathered in place from the underlying bedrock, which is typically a combination of granite, schist and gneiss depending on the location within the province. The author’s experience in the Northeastern US has been on sites where alluvial or coastal plain soils overly the residual soils and partially weathered or intact rock of the Piedmont. The example presented here, from a site on Walnut St in Philadelphia PA, is representative of these projects."

Jan 1, 2016

By Karsten Beckhaus

Barrier walls in levees and dams are designed and constructed for new structures and for rehabilitation or upgrade of existing structures to control seepage. Construction methods applied are often deep soil mixing with a cementitious slurry or excavating a trench and refilling it with a plastic concrete. This paper explains the technical background of jointless cementitious barrier walls inevitably developing thermal tensile stresses and how these stresses can be controlled. The theoretical background of thermal stresses is explained based on experimental and numerical studies of essential factors. Although a low cracking risk is generally inherent, risk mitigation measures should be taken to thermal cracking and to ensure the permanent function of such walls as a low-permeability and high-deformability barriers.

Sep 8, 2021

By John L. Walkinshaw

It is obviously not possible in the time given me today to review in great detail all the research of the past 20 years that the (FHWA) has sponsored or participated in. In this presentation I will highlight some of the principal programs that I am familiar with. This handout lists practically all the reports prepared for the FHWA involving deep foundations and some related work involving the same structural elements (piles, shafts, ground anchors).

Jan 1, 1993

By Sudhir Kumar Das

"The exorbitant price of the land in the metropolis has restricted the horizontal expansion and compelled the owners, the developers and the engineers to opt for vertical expansion. This has resulted in the construction of high rises by extending floors of the existing buildings and developing the new ones for which deep excavation is a must. The multistoried buildings up to a certain height can be founded on shallow depth if the soil beneath can withstand the load. If not, the soil can be stabilized by the latest improvement technology to change the properties of soil to cater the desired load of the superstructures. By such practice the cost and time of completion of the substructures can be reduced in comparison to the substructures needed for deep excavation.The necessity of deep excavation cannot be ignored to create housings, underground parking lots and the other public amenities for the urban migrants in the metropolis.Although most of the metropolis have underground mapping the developers, before starting excavation should be hundred percent sure about the alignment and depth of the utilities so that the excavators do not snap the same to bring cut in water supply, power lines, telephone lines etc, resulting in hue and cry in the neighborhoods of the metropolis due to no availability of the essential services The building/structures coming on the influence zones of the deep excavation should be monitored in all sequences of excavations. In case of building underground corridors for rail or road through open deep excavation under a traffic road the developers, before commencing excavation should shift/divert the dry and wet utilities coming on the way of excavation to suitable locations. The surface traffic need to be diverted either temporarily to an adjacent alternative road or allowed to pass over a decking built over the trench of excavation for the affected length of construction. The soil support system is necessary longitudinally on the two sides covering the width of trench for building corridors. In case of building substructures of flyovers built at different plots along the alignment of the flyover or a multistoried complex built at an isolated plot, the soil support system would be necessary on all the sides covering the plot of construction.The material of construction of soil support depends on the depth, type of soil and the type of permanent structure to be developed. Probable geo-hazards inviting casualties in the deep excavation projects occur due to caving of soil, leakage of wet utilities, seepage through honey comb concrete surfaces, failure of pump used for dewatering etc. A detailed comprehensive planning, management and determination of the project authority is essential for marginalizing the casualties. These prevent unforeseen expenditure in mitigation and help to control the time and the cost over run of overall project. The engineer at site should be more a professional manager than an engineer at site. He should be conversant with the safety and environment rules and regulations applicable to deep underground projects."

Jan 1, 2015

By Lucie Spencer, Craig Butterworth

"This paper presents the design of a raft enhanced pile group recently constructed for a hotel development in Perth, WA. At the time of construction in 2016 the hotel was the tallest prefabricated hotel in Australia.The structure covers the entire 12 m by 32 m development footprint, located in an inner city environment, and directly surrounded by existing structures. The small site and lack of space required innovative thinking in terms of the substructure design.The ground conditions comprise a layer of medium dense sand underlain by variable layers of stiff clay, silts and sands. Groundwater was around 1.5 m below ground level.The substructure design was carried out on the basis of a raft enhanced pile group. This allowed the use of much shorter piles than a conventional pile solution, thereby permitting the adoption of CFA piling techniques. This also allowed the raft thickness to be reduced to such that the substructure works were maintained above the groundwater level.The design was carried out in general accordance with the Australian Standard AS 2159 and using conventional piled raft design techniques involving iteration between elastic soil settlement software and structural analysis software until spring reactions were obtained with convergence of the two models. Following this springs were introduced to model piles in the structure.Due to the variable nature of the ground and resulting uncertainty in pile base capacity it was not considered appropriate to design the system as a pile assisted raft with piles loaded beyond their ultimate geotechnical design strength. As a result, all piles were designed based on a maximum load maintained within the elastic response region, with the majority of the load taken by the piles. However, the combined capacity of the raft and the piles allowed for a saving in pile lengths and numbers of around 40%, when compared to a conventional pile group designed in accordance with the Australian Standard AS 2159.The raft slab was monitored during construction in order to check the actual displacements against the design displacements. At the end of construction, the settlements were found to be within 2 mm of the design values.INTRODUCTIONThe Wellington Street area of Perth in the CBD is undergoing recent regeneration which includes the King’s Square development, Perth Arena and the Wellington Street Bus Station. The proposed hotel development is close to the recent developments on a Lot previously occupied by a low rise development. Due to the small size and constrained nature of the site, the substructure design for the tower needed to take into account available space and the impact of the works on adjacent properties. This paper presents reasoning for the choice of substructure design, details of the design methodology adopted, results from limited post construction monitoring and potential improvements that could be considered for similar future developments."

Jan 1, 1900

By Kozo Takeda, Arashi Shimano

"Dry Jet Mixing (DJM) method as the representative deep mixing technique has been demonstrating best practice on ground mitigation works coping with complicated soil condition and limited site space. This technique plays an important role in many projects to stabilize soft ground involving troubles like sliding failure, settlement, bearing capacity etc. Serious disasters caused larger earthquakes make great demand on the application of deep soil mixing these days. Special design and alignment of deep soil mixing has been established against to liquefaction and serious failure due to liquefaction. In this paper, representative example of liquefaction mitigation by DJM method is summarized. The paper also present result of surveillance of sites installed DJM col umns after attack by Tohoku Pacific Ocean Earthquake. Performance of DJM columns suffered the earthquake is demonstrated at several sites even with conventional column alignment.INTRODUCTIONThe DJM method is a representative deep soil mixing technique of dry mixing manner in Japan. DJM can successfully install soil mixing columns trough automatically controlled binder injection based on pneumatic feeding theory and cumulative experiences.This method was joint-developed in 1978 by private organization under initiative of the Public Works Research Institute of the Ministry of Construction as the optimum method for improving the Japanese soft ground. Figure 1 shows full view of the DJM construction system. Figure 2 illustrates DJM working system indicating Binder Feeding Plant side and Mixing Machine side respectively.As typical soil mitigation method, many projects related with rivers and roads and city development has required DJM technology. The total number of the projects applying DJM has exceeded 5,000 with the total treated soil volume more than 32,000,000 m3 by the end of fiscal year 2013."

Jan 1, 2015

By Wojciech Szczepiński, Dominik Gächter

In early 2020, the construction phase began for the new complex of buildings for Radium Hospital in Oslo – the leading facility for cancer treatment in Norway. Settlements in the surrounding area, caused by pore pressure changes, allowed for the introduction of an alternative solution for the construction of the excavation pit. The presence of solid bedrock and sensitive clay – the same material that causes major landslides in the Scandinavia – in the excavation pit, lead to a combination of techniques, which were never applied in Norway before. For the stabilization of the clay Dry Deep Soil Mixing was applied to allow safe execution of the geotechnical works. Interlocking Bored Piles with footbolts and Jet Grouting columns, in combination with anchors, provided the retaining structure for the excavation pit. Rock injections were performed to avoid any ground water ingress into the pit. Underpinning of fully operational, adjacent buildings was carried out with jet grouting columns. These works were performed from the basement of the hospital and the ‘ACI – Acoustic Column Inspector’ was used to ensure proper installation of 2 m diameter columns to a maximum depth of 25 m. The buildings were later founded on Steel Core Piles, the most common pile type in Scandinavia.

Oct 1, 2021

By Dominik Gächter, Wojciech Szczepiñski

In early 2020, the construction phase began for the new complex of buildings for Radium Hospital in Oslo – the leading facility for cancer treatment in Norway. Settlements in the surrounding area, caused by pore pressure changes, allowed for the introduction of an alternative solution for the construction of the excavation pit. The presence of solid bedrock and sensitive clay – the same material that causes major landslides in the Scandinavia – in the excavation pit, lead to a combination of techniques, which were never applied in Norway before. For the stabilization of the clay Dry Deep Soil Mixing was applied to allow safe execution of the geotechnical works. Interlocking Bored Piles with footbolts and Jet Grouting columns, in combination with anchors, provided the retaining structure for the excavation pit. Rock injections were performed to avoid any ground water ingress into the pit. Underpinning of fully operational, adjacent buildings was carried out with jet grouting columns. These works were performed from the basement of the hospital and the ‘ACI – Acoustic Column Inspector’ was used to ensure proper installation of 2 m diameter columns to a maximum depth of 25 m. The buildings were later founded on Steel Core Piles, the most common pile type in Scandinavia.

Sep 8, 2021

By William Billiet

"The Dulles Silver Line Phase II is an 11.4 mile extension of the Washington Area Metro Transit Authority’s Silver line in northern Virginia. There are three miles of elevated guideway, which are supported on 188 large diameter mono-shafts founded within the Triassic Geologic Aged Culpeper Fault Basin. Three lateral load tests were performed on fully instrumented test shafts. The challenge in developing the load testing program was how to reproduce the effects of the extremely high design loads along the test shafts, considering the limitations of the load test equipment. Development, execution, and analysis of the lateral load test program is discussed.INTRODUCTIONPlans for Dulles Silver Line Phase II include two Aerial Guideway sections on elevated track, the Main Line and Yard Leads. The Aerial Guideways are supported on mono-shafts (single, largediameter drilled shafts) socketed into rock. Lateral loads are resisted primarily through the stiffness of the shaft and the geotechnical resistance of the rock socket. The monoshafts were designed in accordance with AASHTO LRFD 2014. Based on our preliminary analyses, the production mono shafts were expected to consist of 6.5, 7.5, and 8.5 foot diameter drilled shafts with rock socket lengths varying between 8 and 34 feet (averaging 14 feet). Table 1 summarizes the maximum service load combinations for each size production shaft along the aerial guideway alignment.GEOLOGYThe project is located within the Piedmont Province, a major physiographic province on the east coast of the USA extending from Alabama to Pennsylvania. Within the Piedmont, a number of Mesozoic basins formed in rift valleys. Dulles Airport is located in the Culpeper Basin, characterized by a relatively shallow siltstone rock surface compared to the adjacent areas underlain by Piedmont crystalline rocks. The geologic stratigraphy at the load test sites generally consist of residual soils and intermediate geo-material (IGM) overlying siltstone rock. IGM is a term used by Virginia Department of Transportation (VDOT) to describe residual material as it transitions between soil and rock. For the purposes of the load test, the siltstone rock is classified as fractured rock (RQD<50), and competent rock (RQD=50). Table 2 summarizes the stratigraphy encountered at each test site."

Jan 1, 2017

By K. Rainer Massarsch

"Part 1 of 2 By K. Rainer Massarsch, Geo Engineering AB, Stockholm, SwedenINTRODUCTIONConstruction activities, such as driving of piles and sheet piles, soil compaction or excavation generate noise and vibrations. In populated areas these can have a negative impact on the environment, disturb inhabitants and, under unfavorable conditions, cause damage to buildings and installations. This condition is aggravated by the growing public awareness of environmental issues and the increasing use of vibration-sensitive electronic equipment and machinery in industry. In many countries, environmental regulations are enforced more stringently and limit or even prohibit the use of impact or vibratory hammers. This development has restricted the use of cost-effective foundation methods, such as driven and vibrated piles and sheet piles.Vibration problems are gaining importance in many European countries and extensive research has been performed during the past decade, especially with respect to traffic vibrations (Massarsch, 2004). Significant progress has been made owing to the availability of high-quality field measurements and an improved theoretical understanding of how vibrations are generated and transmitted through soil layers. These findings can also be applied to vibration problems associated with construction activities. However, this information is not yet appreciated by the geotechnical profession and even less by the construction industry.This paper discusses the effects of ground vibrations on the surrounding soil and on buildings, with particular emphasis on the different mechanisms of damage that may occur. Guidance is given on the elements which should be taken into account in an assessment of risks associated with piling projects. A simplified method is proposed for assessing the risk of settlements or strength loss in soil deposits. Limiting vibration levels are presented, based on the Swedish standard, which can be used to assess the risk of damage to buildings. Aconcept to predict ground vibrations caused by pile driving and the mechanisms which control the propagation of ground vibrations, will be presented in the second part of this paper."

Jan 1, 2004

By P. Arz

With a total of five basement levels, ground floor and a further six levels above grade, construction of the Kö-Galerie building, on the Königsallee, in the centre of Düsseldorf, was completed with all the difficulties which accompany property development today in the inner city. To meet the intermediate and final deadlines, ad­vanced building techniques were used. Notable among them are the top/down method for simultaneous construction upwards and downwards from an intermediate level, and the use of pre-fabricated composite columns in drilled shafts for the main load-bearing foundations as well as diaphragm walls designed as permanent structural wall of the basement.

Jan 1, 1989

By N. Aarthi, G. R. Dodagoudar

The improvement of soft clay deposits using stone columns is a well-established ground improvement technique in the western world. This technique has been well documented and has proper design codes for precise execution in the field. The sand compaction pile (SCP) method is a contemporary technique to stone columns and has limited literature related to the strength characteristics of the loose to medium dense sand deposits treated with SCP. The available studies on the SCPs installed in cohesionless deposits focused on the improvement by indirectly assessing the SPT-N values pre- and post-installation of the SCPs. The widespread implementation of the SCP technique in recent years has increased the need for a more direct evaluation of the improvement. Earlier studies in this regard have revealed that the available design solutions are based on the type of installation equipment, their working efficiency, and accumulated field data. However, it is found that there are no generic design codes for the direct estimation of the ultimate bearing capacity of the SCP improved cohesionless deposits. To meet the design requirement for the SCP treated ground, a series of experimental and numerical investigations are performed in the present study to arrive at a direct framework in the form of design charts based on the pressure-settlement response of the treated ground. The developed design charts give the ultimate bearing capacity (UBC) of the treated sand deposit for the known initial relative density (RD) of the deposit, spacing and diameter of the SCPs, size of the footing, and for the specified target unit weight required for the intended application. It is concluded that the design charts will be of preliminary use to the design engineers to directly evaluate the UBC of the SCP improved loose to medium dense cohesionless deposits as part of the SCP method of ground improvement. It is expected to have more field-scale experiments and in-depth analysis before implementing these charts for actual field execution.

Nov 1, 2022

By Muttharam M, Karthick Kumar V

Helical piles foundation systems have been extensively used in engineering application. It is commonly adopted to resist the compression, uplift force, overturning moment and lateral forces. Helical pile system is extensively used in many structures such as Transmission towers, Wind farms and other offshore structure because it is easy and quick to install. Realizing the importance of helical pile, an attempt is made in the present investigation to bring out the effect of spacing between the helix, blade thickness, and shaft thickness through numerical analysis. To validate the finite element model experimental investigation was carried out. In this investigation model steel piles with dual helical plate embedded in clay bed with the consistency of 0.4 was tested to study the effect of uplift loading on the behaviour of piles in tensions. Model helical pile with 12.5 mm diameter circular shaft and helix diameter of 25 mm. The model pile embedded in clay bed for a depth of 400 mm. Parametric analysis of helical pile by varying blade thickness, shaft thickness, and the spacing of helix was carried out by using Finite Element tool Plaxis 3D. From this analysis, an increase in thickness from 4 mm to 10mm increase the uplift load. Similarly, an increase in spacing of helices from 0.5 m to 1.5m increase the uplift capacity beyond that it decreases the uplift capacity. By keeping the contact area of the helix as constant as the number of a helix and helical spacing was varied, the critical number of the helix was found as 2 and the critical spacing of helix was found as 1.5 m for this study.

Nov 1, 2022

By Nick Hytiris, Mohammed Al Maadheedi, Slobodan B. Mickovski

This paper explores the capacity effects of a square steel plate welded at the ground surface on a driven open-ended steel pile (i.e. the plate would touch the ground surface after the pile achieves the required penetration). A series of strain-controlled, 1-g laboratory tests were undertaken on piles with and without a square steel plate attached. The piles were driven in dry, loosely packed, uniform sand. Two plates were used, one with a breadth equal to two times the diameter of the pile (2D) and the other with a breadth equal to three times the diameter of the piles (3D). A 20% increase in capacity was recorded for the 2D plate, and a 110% increase in capacity was recorded for the 3D plate when compared to the pile without an attached steel plate. The back-analysis of the results allowed the derivation of a new expression to calculate the capacity of bearing plates, which accounted for the effects of sands compaction and dilation. By extrapolating the findings of these tests to a hypothetical scenario, a model design problem was described where the length of a pile can be reduced by 20% to 60% (depending on the load) by using a plate attached to the pile. The results of this study can help designers to minimise penetration depth; thus, achieving a more economical and sustainable design.

By Mohammed Al Maadheedi

This paper explores the capacity effects of a square steel plate welded at the ground surface on a driven open-ended steel pile (i.e. the plate would touch the ground surface after the pile achieves the required penetration). A series of strain-controlled, 1-g laboratory tests were undertaken on piles with and without a square steel plate attached. The piles were driven in dry, loosely packed, uniform sand. Two plates were used, one with a breadth equal to two times the diameter of the pile (2D) and the other with a breadth equal to three times the diameter of the piles (3D). A 20% increase in capacity was recorded for the 2D plate, and a 110% increase in capacity was recorded for the 3D plate when compared to the pile without an attached steel plate. The back-analysis of the results allowed the derivation of a new expression to calculate the capacity of bearing plates, which accounted for the effects of sands compaction and dilation. By extrapolating the findings of these tests to a hypothetical scenario, a model design problem was described where the length of a pile can be reduced by 20% to 60% (depending on the load) by using a plate attached to the pile. The results of this study can help designers to minimise penetration depth; thus, achieving a more economical and sustainable design.

By Jeffrey M. Taylor, Arturo Ressi di Cervia

"Construction of the drilled shafts for the Brightman Street Bridge Replacement Project were not only challenging due to working over the water but were also challenged by changed soil conditions, concurrent work being performed by an adjacent contractor on the same project, environmental restrictions and severe winter conditions. A total of 36 x 8 foot (2.44m) diameter drilled shafts with 7.5 foot (2.31m) rock sockets were installed for the East and West bascule piers. This project also included Osterberg Cell load testing on two production drilled shafts at both the East and West bascule piers. The results from the load test program were used to fine tune the design of the drilled shaft rock sockets. From a constructability standpoint the reverse circulation drilling method with a pile top drill rig proved to be an excellent choice for drilling the overburden and rock sockets of the large diameter deep drilled shafts. INTRODUCTIONThe replacement Brightman Street Bridge spans the Taunton River between Fall River and Somerset in Massachusetts.The new crossing is located approximately 1500 feet (450m) upstream from the existing Brightman Street Bridge, which was built in 1908. The new mainline bridge includes nine spans totaling 1725 feet (525m). A bascule type moveable span will be located in the middle of the Taunton River and provide a 200 foot (61m) open channel centered about the 400 foot (122m) navigational channel. The bascule span, which has a span length of 409 feet (124.7m), will be a trunnion-type four leaf structure with a solid deck. A site plan is shown in Figure 1 Contract 3, which includes construction of the foundations for the East and West bascule piers, was bid on December 19, 2000 and was awarded to Modern Continental Construction Company (MCC) on January 24, 2001. MCC in turn awarded the subcontract for the installation of the drilled shafts to TREVIICOS Corporation, which started mobilizing in June of 2001.The scope of work for the drilled shafts of Contract 3 consisted in installing 18 drilled shafts in three rows on each side of the river to support the bascule piers located in the middle of the Taunton River.The foundation plan for the bascule span is shown in Figure 2."

Jan 1, 2004

By Abolfazl Eslami, Sepide Lotfi, Mohammad M. Eslami

"Via direct CPT methods for pile capacity prediction, correlation coefficients smaller than unity are used to relate cone tip resistance (qc) and sleeve friction (fs) to pile toe capacity (rt) and shaft capacity (rs), respectively. For linking CPT data to pile capacity, factors such as diameter, penetration rate, partial embedment of pile toe into a hard layer, mechanism of plunging, failure zone, data processing, and stress-strain conditions must be considered. The aim of this paper is to investigate the role and significance of scale effects and establish direct relation between CPT data and pile shaft capacity. A database has been compiled including 40 full scale pile load tests and CPT sounding records for calibration and validation of the proposed approach. Analytical studies demonstrate that differences between pile and penetrometer penetration rate, geometry, and stress-strain conditions influence the relation between fs and rs. By considering the determinants, a procedure is proposed from which the pile shaft capacity can be predicted. This approach demonstrates better agreement with measured capacity by static loading test and less scatter than other current CPT methods.IntroductionAmong different approaches for pile capacity prediction, in-situ tests such as SPT and CPT have been used as supplementary of static analysis. Due to similarities between CPT and pile, the measured cone tip resistance and sleeve friction can be employed for prediction of unit toe and shaft capacities, respectively.Determination of pile capacity from CPT data includes two main approaches: direct and indirect methods. Direct CPT methods apply the measured values of cone tip resistance (qc) for pile toe capacity (rt), and sleeve friction (fs) for pile shaft capacity (rs) with some modifications regarding scale effects. Indirect CPT methods employ friction angle and undrained shear strength values that have been estimated from CPT data.When using direct CPT methods to relate qc and fs to rt and rs, correlation coefficients smaller than unity are used. Factors such as diameter, penetration rate, mechanism of plunging, failure zone, data processing, and stress-strain conditions must be considered for correlation between CPT and pile capacity. The work presented in this paper aims toward ameliorating the situation in the area of pile shaft capacity prediction, based on cone sleeve friction.Case histories from full-scale tests are compiled and analyzed by means of six methods including five direct CPT methods for shaft capacity prediction and the proposed method."

Jan 1, 2015