Search Documents

By J. Bouchard, Ali Vazirizadeh, R. del Villar

"The amount of water reporting to the concentrate correlates well with the solid entrainment. It is well known that the frother and collector dosage as well as the froth depth and gas rate influence the amount of water reporting to the concentrate. This is also true for gas dispersion properties such as gas holdup and bubble surface area flux. On the other hand, a positive bias rate, required to reduce hydraulic entrainment, also affects water recovery and thus the particle recovered by entrainment (depending on the their size). Up until now, the effect of the gas rate on the water recovery has been studied, but no comprehensive investigation on the gas holdup, bubble size and bubble surface area flux has yet been reported. This research precisely aims at addressing this issue. The experimental work was carried out under a constant gas flow rate to eliminate the gas volume effect, while other gas dispersion properties have been varied by modifying the frother concentration and the shearing water introduced to the frit-and-sleeve sparger. A constant froth depth and no wash water were used, in order to be able to evaluate the exclusive correlation between the water recovery and the bubble surface area flux and/or the bubble size. It is worth mentioning, that the particle size of the hydrophobic particles did not show a significant effect on the amount of water going to the concentrate. Not surprisingly, experimental results demonstrate that water recovery increases with the bubble surface area flux and with the gas hold-up."

Jan 1, 2014

By Glaser. C., J. Balz, F. Logsch, R. Heiduschke, M. Leiker, P. Ay

The treatment of iron-hydroxide-containing water from ground water and surface water is achieved by a combination of the process steps of flocculation and subsequent mechanical dewatering. The aim is to create solid pellet structures by extending the structure forming flocculation process with a build-up pelletizing process which can be transferred directly into a drying unit. A Taylor-Couette-reactor (diameter of the inner cylinder – 40 mm, gap width – 5 mm) was used for these experimental studies. To produce the necessary flow profile the inner cylinder was rotated at a speed of 230 rpm. The iron hydroxide-containing suspension (dry matter content: 2 mass %) was added simultaneously with the addition of a cationic high-molecular flocculant in various flocculant dosages and residence times of 5 to 15 min. The pellets were examined for parameters such as geometric dimensions, dry substance content and dewatering behaviour. As the results show, there is a direct relationship between the residence time and the geometric dimensions of the pellets. After a residence time of 5 min, round pellets with an average diameter of 6 mm were formed. With an increase in the residence time up to 15 min, a compaction of the pellets could be observed, which resulted in an increase in the dry substance content of 8.0 to 11.2 mass % on average. After completion of the pelletizing process, the pellets were mechanically dewatered by filtration. By applying this innovative wet pelletizing of iron-hydroxide containing suspensions in a Taylor-Couette-reactor, it is possible to carry out the process of flocculation combined with the pellet formation with simultaneous pellet compaction in a single process step. The resulting pellet structures are distinguished from conventional floc structures by an improved water discharge capacity. After classification the pellets can be marked directly as easy-to-handle bulk material, suitable as feedstock in percolation columns for the purification of contaminated fluid streams

Jan 1, 2018

"The business importance of water for mining companies is unequivocal as it may affect several aspects of mining projects ranging from the life-and-death license to operate to the imperative economic viability. It is thus no wonder that nearly all mining companies acknowledge water-related risks, issues and opportunities in their respective sustainability report. Somehow, this procedure has fostered the idea that water frugality could be the sustainable solution to several water-related issues. The regular exercise of water accounting should then follow as a key strategic requirement. Water accounting is defined as the application of a consistent and structured approach to identifying, measuring, recording and reporting information about water. However, several factors discussed herein have led to the fact that some water accounts are still produced using means (hardware and software) which undermatch the value actually associated with water. The resulting fuzziness about water usage could result in missed opportunities, suboptimal operations or even lead to environmental law violations. This paper subscribes to the distinctive perspective that, once underlying concepts and practical definitions have been standardized under a supported framework, such as the openly available Water Accounting Framework (WAF) published by the Minerals Council of Australia, most of the remaining water accounting issues may be boiled down to accuracy issues and, ultimately, to how much accuracy is valued by the stakeholders. Using the latest WAF document as a baseline for best practices of water accounting and, borrowing concepts from the fields of sensor network design in the process industries and best practices of metal accounting, this paper reviews some essential accuracy issues to be considered when designing or analyzing water accounting systems in mineral processing. The current paper also includes some elements for a promising attempt to include the value of information paradigm inside the water accounting best practices."

Jan 1, 2014

By W. H. Cheung

Nickel and cobalt production relies heavily on the processing of nickel laterite ores; these ores contain the majority of known Ni and Co reserves, 80% and 90% ~ 95%, respectively. The Caron process is used to extract Ni and Co metals from low-grade nickel laterite ores (1% Ni and 0.1% Co). It involves selective reduction of NiO and CoO minerals followed by ammoniacal leaching. Despite low metal recoveries, this process continues to be technically and economically reliable and thus commercially important globally. However, keeping the Caron process cost-effective has been a challenge for industries because of increasing economic and environmental pressures. Although studies of the Caron process have been extensive, significant improvements in recoveries of industrial processes have not been forthcoming. Reported industrial metal recovery from high iron content ore is only 80% ~ 85% for Ni and only 40% ~ 45% for Co; recovery is even lower for ores rich in magnesium. The real difficulty here is that there is no complete understanding of and control over the complex series of reactions in the ore and in the leaching solution during processing. Achieving effective metal recoveries from the Caron will require control of the mineral transformations, which affect the activation of minerals by reduction. In this study, the effect of over-reduction was investigated, which superseded the effect of activation by lowering the activity of the minerals and thus metal dissolution. Reduction was carried out in a batch reduction apparatus with 1:1 and 1:2.5 CO/CO2 gas mixtures from temperatures of 500 ~ 700°C and residence times up to 60 minutes. The pre-reduced ores were leached using a standard ammoniacal leaching test. Thermodynamic analysis and possible effects of stable phase field on leaching was examined. The results suggest that control of over reduction effects are directly related to the mineral transformation and reduction conditions.

Jan 1, 2014

By S. Carsten, S. Subramanian, R. Vasant Kumar, S. Vimalnath

"The effect of EPS components namely protein, polysaccharide and biosurfactant purified from Pseudomonas fluorescens was investigated for the bioremediation of Pb(II) ions in aqueous solution. Two parameters, namely the amount of EPS component and the concentration of Pb(II) ions were optimized for maximum Pb(II) ions uptake. The EPS components interacted with Pb(II) ions were characterized using energy dispersive X-ray analysis (EDAX) to ascertain the presence of Pb and by attenuated total reflection-Fourier transform infrared spectroscopy (ATR–FTIR) to reveal the functional groups involved in Pb(II) binding. The maximum Pb(II) binding capacities of protein, polysaccharide and biosurfactant were found to be 11.4, 0.55 and 0.11 mg mg-1 respectively. The biosorption processes followed the Langmuir model. The Gibbs free energy (?G0) values of -23.6, -20.9 and -23.2 kJ mol-1 for Pb(II) biosorption by protein, polysaccharide and biosurfactant respectively, attested to spontaneous, chemisorption processes. The ATR–FTIR results revealed the presence and involvement of amino, hydroxyl, carboxyl, phosphate, and methyl functional groups in Pb(II) binding and EDAX analysis confirmed the interaction of Pb with EPS components. The Pb(II) binding mechanisms of EPS have been discussed. The results demonstrate the potential of the purified EPS components of P. fluorescens for removal of Pb(II) ions from aqueous solution INTRODUCTION Waste water containing toxic metals from various industries pose a serious threat to human health and ecosystem. For treating such waste water, conventional methods like chemical precipitation, coagulation, evaporative recovery, electrodialysis, floatation, flocculation, ion exchange, reverse osmosis, nanofiltration, ultrafiltration are used (Lakherwal et al., 2014). These methods have some disadvantages like toxic sludge generation, incomplete metal removal and high cost (Singh and Gadi, 2012), necessitating the search for cheaper and efficient alternative methods. Bioremediation is one of the emerging alternatives where bacteria, fungi, yeast, algae and other biological substances are used as sorbents to remove toxic heavy metals (Vijayaraghavan, et al., 2015). Recently, the bioremediation potential of extracellular polymeric substances (EPS) of microbial origin has attracted attention. However, for Pb(II) removal, there is a paucity of literature focusing on EPS."

Jan 1, 2018

By Saveliy F. Kaplan, Valeriy N. Tsyplakov, Vasily N. Kovalev, Igor A. Agapov, Nikolai V. Vorob’ev-Desyatovskii

"Based on the experiments, a possibility of successful processing of double-refractory gold sulphide concentrates with a high content of natural organic carbon, which has a high sorption capacity toward gold chloride complexes, has been demonstrated. The proposed approach involves deep burnout of sorption-active organic carbon in an autoclave at a higher temperature and a longer retention time. INTRODUCTION It is known that one of the reasons why gold-bearing ores and concentrates are refractory is the occurrence of fine gold in sulphides (usually in pyrite and arsenopyrite) in ores and concentrates. In addition, refractory gold-bearing ores and concentrates also contain an organic carbonaceous material, which has a sorption capacity towards gold chloride complex, making the ore or concentrate even more refractory. In pressure oxidation, metallic gold is oxidized by Fe (III) aqua-ions and complex Au(Cl)4- ions are formed at temperatures over 180°C, in the presence of chlorides contained in ores. Complex gold anion is adsorbed on the organic carbon surface and then reduced to Au0; the chloride ion is regenerated and gold, adsorbed on organic carbon microparticles, is ultimately transferred to tailings (preg-robbing). Currently, there are several suggestions how to suppress preg-robbing (Simmons, 1998, Pyke, 1999, Rees, van Deventer, 2000, Zhao Jun-wei, 2008). It can be done by reducing the organic carbon content by processing (flotation, etc.),reducing chloride ion concentration by preliminary washing of concentrates in thickeners, reducing the adsorption capacity of organic carbonaceous material by introducing some organic substances that are strongly adsorbed on its surface (blanking agents), and reducing the redox potential of the slurry liquids by introducing neutralizing agents (limestone)."

Jan 1, 2018

By R. C. Miranda

The purpose of this work is to present ?state of the art? mass balances closing strategies in ore treatment plants. It presents a brief history of difficulties and challenges ahead. The current methodology is based on usage of an expert system, which seizes and filters the plant data, analyzes situations of equipment stops and mostly instruments failures. It is still possible to internally create a strategy to check the data of an instrument failure. The system is coupled to software with a Lagrangian model of mass balance closure that receives the pre-treated data. Thus, the data goes through filtering and reconciling processes to generate a reliable mass balance of the ore treatment plant. This made possible to obtain a system that is able to tell the real productivity of a ore plant through reliable mass balances. Residence times on equipments are critical to the balance, thus, they require good logic to eliminate errors due to the characteristics of non-steady state. Among the next challenges is the inclusion of a ?soft sensor? as a replacement of an instrument required for mass balance closure.

Sep 1, 2012

By Aysan Molaei, Kristian Waters

Solvent extraction is the one of the most common techniques for recovering metal ions from aqueous systems. However, solvent extraction is generally limited to relatively high concentrations and requires a high organic/aqueous ratio. Predispersed solvent extraction (PDSE) is a modified solvent extraction technique in which organic phase pre-comminute into colloidal liquid aphrons (CLAs). In this study, the extraction of copper by the PDSE technique was investigated. The main focus of this study was on the characterization and application of CLAs under different operational conditions, and to investigate the effects of different parameters on the extraction of copper from dilute streams. The effect of phase volume ratio (PVR), initial extractant concentration and initial copper concentration was studied and optimum conditions for copper removal using CLAs generated by LIX 984N as extractant, oil soluble and water soluble surfactants were proposed. Experimental observations indicated that PVR and initial LIX 984N concentrations had a significant effect on copper extraction.

Jan 1, 2014

By V. A. Luganov

Methods of treatment of pyrite concentrates differ, depending on the content of pyrite and non-ferrous metals: oxidation roasting, sulphatization roasting, smelting, direct hydrometallurgical treatment and so on. Existing technologies do not provide for high recovery of metals, expenses associated with existing technologies are high, and environmental issues, associated with the existing technologies need serious attention. We have developed universal technology of the activating-dissociating autogenous roasting of pyrite concentrates using air based, or air, enriched with oxygen, blow. The basic process is taking place in accordance with the following reaction: (1-x)FeS2 + (1-2x)O2 = Fe1-xS + (1-2x)SO2 +Q The products of this reaction are pyrrhotinized cinder and roasting gases, rich in SO2 (up to 18 % in case of air blow) and poor in SO3, that contain up to 1 % of elemental sulphur. Cinder contains different forms of pyrrhotite. These forms of pyrrhotite differ by its content (from Fe0.843S to Fe0.945S), thermodynamic, magnetic (from 4.10-1 to 3.6 SI units), flotation properties (with pyrite dissociation the ?-potential of the product is moving towards more electrically positive charge, from 0.95 for pyrite to 0.2 for dissociation products) and other properties that depend on the conditions of roasting. The combination of pyrrhotizing roasting with different methods of cinder treatment allows to increase the level of sulphatization of non-ferrous metals during the roasting; reduce the amount of blow used during the processing; reduce dust losses to the gas phase; reduce the capacity of gas cleaning system and increase resistance to corrosion of the gas-treatment system, used for the production of sulfuric acid from pyrites. This combination of treatments also allows to use magnetic separation and flotation for separation of ferrous and non-ferrous metal compounds during cinder treatment; perform de-arsenation of arsenic containing concentrates and by-products. Pyrrhotinized cinder may be treated by oxidizing and non-oxidizing hydrometallurgical methods. Keywords: Pyrite, polymetallic ores, sulphidization roasting, pyrrhotite, magnetic separation, arsenic sulphide

Sep 1, 2012

By James A. Finch, Xiangzhou Ding, Yue Hua Tan

"The Jameson Cell is one of the choices of flotation machine in coal, base metal processing and other specialist applications. This paper determines the effect on vacuum pressure and bubble size of two design variables, orifice size and downcomer length, and the operating variable air-to-water (AWR) ratio. The main findings are: orifice size and downcomer length impact the vacuum but have limited effect on bubble size; AWR < 1 favours high vacuum, conditions are identified where vacuum is maintained at AWR > 1, and water flowrate has slightly greater impact on bubble size than air flowrate.INTRODUCTIONFroth flotation, the most common technique for mineral separation, has been in use for over a century. The process takes advantage of the difference in wettability of mineral surfaces to achieve the separation of valuable minerals from non-valuable minerals, or gangue. Numerous flotation machines have been invented and patented over the years. The Jameson Cell, invented by Professor Graeme Jameson in the late 1980s, is one successful example. First trialed at Mount Isa Mines (Queensland, Australia), Jameson Cells have been installed at operations around the world for the recovery of fine coal (Mohanty and Honakeri, 1999; Cowburn et al., 2006; Hacifazlioglu and Toroglu, 2007; Uçurum 2009), minerals of copper (Farr 1992; Atkinson et al., 1993; Harbort et al., 1997), lead/zinc (Rohner, 1993; Munro, 2003) and gold (Bennett et al., 2012; Lauder et al., 2003), and in water treatment (Yan and Jameson, 2004), solvent extraction de-oiling (Miller and Readett, 1992; Miller et al., 1997; Harbort et al., 2003; Young et al., 2006), oil sands processing (Neiman et al., 2012), and various food industries (Brenneman, 2014). One of the largest units is the 650 cm diameter separation tank with 24 downcomers installed in an Anglo American operation (Osborne and Euston, 2015). Scale up is relatively straightforward: to increase capacity the number of downcomers is increased with corresponding increase in size of separation tank.The Jameson Cell comprises two main parts: a vertical tube (downcomer) which provides self-aspiration and intense bubble-particles contact, and a (separation) tank where particle-bubble aggregates disengage from the pulp. The intense bubble/slurry mixing in the downcomer with air holdups reaching 60% (Marchese et al., 1992) accelerates particle collection enabling the greatly reduced cell volume compared with mechanical flotation cells and columns. The disengagement of the particle-loaded bubbles from the slurry in the separation tank is usually aided by addition of washwater."

Jan 1, 2018

By Thomas Mütze, Anja Hirte, Ursx Peuker, Thomas Kuhn

"The comminution behavior of two ferromanganese nodules samples of the equatorial northeast Pacific has been examined as a basis for the separation of two kinds of metal-rich layers. Those layers were finely grown together during nodule formation and are one reason that the exploration of deep-sea minerals calls for the development of new mineral processing concepts. Therefore fundamental analyses of the fracture behavior have been made under compressive and impact stress. Further experiments took focus on the crushing behavior in a jaw crusher and a small scale impact crusher as well as the milling behavior in a dry vibrating mill, a wet planetary ball mill, and a wet agitated ball mill. The comminuted products were characterized by PSD, particle shape, particle density, and porosity. The experiments show a low stress resistance of the ferromanganese nodules. Compared to compressive stress, impact stress turned out to be the more effective for crushing. Both samples showed no significant difference in the comminution behaviour which makes differing mechanical treatments unnecessary. In both cases particle sizes below 1 µm were achieved by wet grinding. This particle size is necessary to separate the two kinds of metal-rich layers which is part of continuative studies."

Jan 1, 2014

By M. Alvarez-Silva

The control of the amount of chromite reporting to the concentrate during the flotation of UG2 ore is of critical importance since its presence affects the downstream smelting process. It is generally reported that the main mechanism responsible for chromite recovery is through entrainment. This is reflected in analyzing the solids and water recoveries. These in turn are strongly dependent on the froth phase. In the present investigation a laboratory scale column flotation cell was used to investigate the role of the froth phase in the flotation of UG2 ore. Such a device is superior to a standard batch cell since it operates at steady state in open circuit and also allows for a greater degree of flexibility in terms of froth heights. The mass of solids and water recovered in the concentrate as well as chromite (Cr2O3) recovery by size class was determined as a function of froth height, superficial gas velocity and depressant dosage. The results showed that depressants had little effect on chromite recovery but increased the grade due to the depression of gangue minerals. A 60cm froth height always resulted in slightly lower solids, water and chromite recovery than for 30cm. Typically only 20-25 % of solids reaching the pulp-froth interface reached the launder. The relationship between solids and water recovery for a wide range of conditions indicated that chromite is mostly recovered by entrainment. Keywords: UG2 ore, column flotation cell

Sep 1, 2012

By Bulelwa Ndlovu, Saeed Farrokhpay, Dee Bradshaw

The effects of phyllosilicate minerals on the flotation performance and froth stability of a copper ore was investigated. It was found that various phyllosilicate minerals affect the copper recovery differently however they all caused the flotation grade to be reduced. The effect of different phyllosilicate minerals on the froth stability followed the order of talc >> montmorillonite > muscovite > kaolinite > illite. The results demonstrated that there could be a relationship between the deleterious effect of phyllosilicate minerals on the flotation and froth stability. Talc and montmorillonite have both shown the highest effect on the flotation recovery and grade as well as froth stability. On the other hand, illite has the least effect on the both flotation performance and froth stability. Kaolinite and muscovite also affected the copper flotation grade (but not the recovery) while they also affected the froth stability. Therefore it is possible to control the flotation performance when phyllosilicate minerals are present via monitoring and controlling froth stability which needs to be investigated further.

Jan 1, 2014

By A. Morrison, D. Mesa, P. R. Brito-Parada

"Froth flotation is the most widely used mineral separation technique. It is based on the relative hydrophobicity of valuable and gangue particles. In a flotation tank, two distinct zones can be identified: the pulp and the froth. The pulp is a turbulent region in which hydrophobic valuable particles attach to air bubbles while hydrophilic gangue particles remain in the slurry. As the particle-laden bubbles rise, a mineralised froth zone is formed that overflows as a concentrate. Although the process is more than a hundred years old, there remain many aspects that are not completely understood, particularly for the froth zone. Thus, the rules governing the design of flotation tanks tend to focus on pulp zone parameters, which are largely based on operating data. An example of this is the design and operation of impellers. These tend to be designed paying attention to hydrodynamic phenomena in the pulp zone, but their effect on the froth zone has not been completely addressed. The role of impellers in a flotation tank is to break the air bubbles in order to generate smaller ones and to provide an environment that enables the collision between those bubbles and the particles in the slurry. This usually creates turbulent regimes that can affect the pulp-froth interface, destabilising the lower regions of the froth and affecting the overall performance of the process. Different impeller designs and retrofit modifications have been proposed in the past, addressing some of those issues. However, there is no systematic study of the effect of different impeller designs on the bubble size in the pulp and its links to the stability of the froth. This work tested the impact of an impeller designs combined with the use of a stator on the performance of an 87 litres continuously operated laboratory-scale flotation tank, with a focus on bubble size in the pulp and froth stability. The results showed that the implementation of a stator system decreased bubble size and increased froth stability. That resulted in an increase of mass pull, measured as a proxy of metallurgical recovery."

Jan 1, 2018

By M. Ranjbar, M. Khosravi Rad, A. Tohry

"The filling degree is defined as the volume ratio of the load inside the mill, which determines the power drawn from the motor, as long as the filling degree is not more than the optimum level. As the filling degree increases beyond the optimum level, the impact energy inside the mill will decrease and as a consequent, the mill power output will also decrease. Therefore, the mill filling degree is a key parameter in evaluating the grinding circuit performance, as it determines the mill reaction to the input feed. Since this parameter has an impact on the mill capacity, measuring the mill load is vital for control and optimization of grinding process. As in Choghart Processing Plant no instrument is available to measure the AG mill filling degree, an empirical model based on the bearing-oil pressure is proposed. The AG mill filling degree was related to the differences between the average pressure of input and output bearings, the circulating load and power drawn. It was shown that a quadratic model could relate the mill filling to the above mentioned measurements. This model showed that when the power drawn and circulating load decreases the bearing-oil pressure needs to be checked. If the bearing-oil pressure increases the feed rate needs to be decreased and steel ball be charged to the mill to increase the grinding and prevent mill overloading. INTRODUCTION The feed quality (size and hardness) affects the grinding process in AG mills. Reducing the top feed size and increasing the ore hardness reduce the mill efficiency and increase the particles with critical dimensions inside the mill. These will result in increasing the mill filling degree and reducing the mill throughput and efficiency (Wills and Finch, 2015). The volume ratio of the load inside the mill is called filling degree, which determines the mill power drawn. It is believed that if more energy is mainly spent on grinding (Wills and Finch, 2015). Therefore the mill power draw is used as a mean to control the mill efficiency."

Jan 1, 2018

By Prasad Kopparthi, Narasimha Mangadoddy, Balraju Vadlakonda, A. K. Mukhurjee

"Column flotation (CF) is widely using equipment in mineral processing since many years. ERT technique facilitates non-invasive and nonintrusive visualization of different parameters in a column flotation. The hydrodynamic investigation of two-phase and three-phase are studied using electrical resistance tomography (ERT) coupled with pressure transducers in laboratory column flotation. Bubble size distribution, bubble rise velocity and gas and solids hold-up hydrodynamic parameters are extensively used for column flotation design and performance evaluation. The effect of superficial gas velocity, feed flow rate and slurry height in the column on mean gas holdup and its radial distribution has been analyzed for both two-phase and three phase flows. Influence of solid particles on gas hold-up and its complete elucidation of dispersion in the column are assessed. Experimental results show ERT coupled with PT is suitable as an online monitoring tool to provide useful information on the hydrodynamic parameters of the column flotation. The tomography images, which were generated using a modified sensitivity back projection algorithm, were employed to explore the parameter study in two phase flow in column flotation.Furthermore, the results also indicate that ERT is a very powerful tool for diagnosing the `inside' flow behaviour of gas-liquid two-phase and gas–liquid–solid three-phase flow in columns operating for a wide range of flow regimes.INTRODUCTIONColumn flotation is being widely used in mineral processing industries in last few decades. There has been a lot of attention in understanding the various mechanisms that take place during operation. Due to many reasons column flotation has been found to yield better performance than conventional flotation cells, particularly with fine particles (Honaker and Mohanty, 1996). Due to complex flow behavior in nature, the performance of column flotation influenced by on flow characteristics of the process, (Jena et al., 2008). Previously basic research is carried out to evaluate the effect of the hydrodynamic parameters on the performance of column flotation (Finch and Dobby, 1991)."

Jan 1, 2018

By Rakesh Kumar, S. Mehrotra, T. Alex

"This paper, an overview of our recent findings on mechanical activation (MA) of minerals/materials, emphasizes the importance of sample genesis, mechanically induced/altered porosity and surface area, mineral interactions, glassy inorganic materials, surface alteration and zeta potential changes and, mechanically induced reactivity of solids. Materials investigated include Al-oxyhydroxides (gibbsite and boehmite), fly ash and granulated blast furnace slag. Planetary, attrition, vibratory and conventional ball mills are used for MA. Genesis of boehmite has been found to have a bearing on its behavior during MA. For example, BET specific surface area (SSA) of boehmite prepared by thermal dehydroxylation of gibbsite has decreased from 265 to 65 m2/g during 240 min of MA; in contrast, the SSA of hydrothermal boehmite has increased from ~2 to 36 m2/g. Mechanisms of surface area changes in the two boehmite samples differing in their genesis is explored. MA of gibbsite and its mixture with hematite/quartz using attrition milling has indicated that the presence of the second phase promotes amorphisation. Amorphous materials show signs of change in nature of bonding during milling as illustrated by MA of fly ash. Physicochemical changes during MA are not restricted to the bulk phase. The genesis of zeta potential changes in MA solids can be many; for example texture induced zeta potential changes as observed for gibbsite, while zeta potential changes during the milling of granulated blast furnace slag occur due to enhanced (possibly non-congruent) dissolution. Interesting manifestations of mechanically induced reactivity and its correlation with physicochemical changes are illustrated in terms of alkali leaching of boehmite and, hydration of MA slag. New findings reported here are associated with several open questions and are highlighted in the paper."

Jan 1, 2014

By Christopher Tucker, Marcello Veiga

Social issues are increasingly recognized as significant inhibitors to mineral development projects. Increasingly social risk is being recognized as a key factor determining the success of a mineral investment. Groups opposed to a mine for social or political reasons often use environmental impacts, real or perceived, to prevent mine development. These risk factors depend largely on cultural perceptions of mining activities and must be understood as such in order to be appropriately managed. A first step to addressing social issues is inclusive, transparent and meaningful engagement of stakeholders. This process allows stakeholders to understand what the other parties value in order to collectively establish a common currency for development and the creation of mutual value. Expanding the scope of benefits and values a mine can bring is of increasing importance to mining companies who typically consult outside specialists remote from the mine site and late in the development timeline for this purpose. Training technical staff, engineers and geologists, who make initial and ongoing contact with local interests, in a holistic approach to mine development is crucial to successful and economic mineral development projects. Further extending this conversation to the general public, media governments and non-governmental organizations is a necessary step in developing a meaningful discourse on the benefit of mining activities.

Jan 1, 2014

By Narasimha Mangadoddy

The complex nature of multi-phase flow in dense medium cyclones has restricted plant operators and designers to rely on empirical equations for predicting the performance. A number of empirical cyclone models have been developed in the past (Wood, 1990; Dunglison, 2002). In recent years, this subject has been broached with computational fluid dynamics (CFD). Most of the CFD models have not considered the correct rheological behavior of magnetite medium while simulating the medium segregation inside the cyclone. These models mostly predict excessive underflow volumetric flow rates. In this paper simulations of magnetite medium in a dense medium cyclone, were conducted in FLUENT where the particle phases were simulated using the modified Mixture model. The turbulence was resolved using Large Eddy Simulation (LES) model. The rheological behavior of medium was considered in the form of Granular viscosity, Newtonian and Non-Newtonian models corrected with particle loadings and fraction of ultrafines. Multi-phase simulations using granular viscosity option although predict the overall split product medium densities reasonably close to experiments, the mixture viscosity values are restricted to substantially lower values, similar to water viscosity. Simulations using Newtonian viscosity model corrected with particle loading, and fine fraction below 53µm size is predicting overall mixture viscosity levels well over water viscosity levels, but under predicting the under flow the underflow medium density. Multi-phase simulations using Non-Newtonian Herschel-Buckley model, calibrated for superfine magnetite medium measured viscosities, is closely predicting the medium segregation with gamma ray tomography data. Overall predicted product medium densities, underflow volume split are close to the experimental data. This model is can be further used to simulate coal portioning and hence in developing new designs.

Sep 1, 2012

By M. Evertsson, E. Hulthén

"In aggregate production and mining the operators are responsible for controlling and monitoring the process to maintain high plant throughput and safe operation. Operators have to make different decisions to control the process due to changed demand on the operation from both management and conditions of the process. The quality of the response and the time it takes for an operator to respond to altered demand relies on what information is available and the experience of the operator. In this work a dynamic simulation platform has been developed to be used for operator training. Models for representing production units and process control for plant simulations have been developed and implemented in MATLAB/SIMULINK to simulate time-dependent plant behavior. Stochastic and scheduled events are included using the discrete events simulation toolbox SimEvents. The human-machine interface was developed using the human-machine interface software ICONICS. The operators’ cognitive process, in interpreting the plants semantic, has been studied by observations and with informal interviews with operators. This was done to get information about the daily operation and the problems that occur in the process. By interacting with operators that experience different physical interactions with the process; more qualitative e-learning software for supporting operator training in a dynamic operator environment could be developed. The quality of the operator training environment was evaluated with a usability study that was performed with operators and others within the production."

Jan 1, 2014