Search Documents

By D. W. Feng

Thiosulfate as an alternative lixiviant for gold has received much attention in recent years due to the growing environmental concerns over the use of cyanide. Cu(II) is used to catalyze the oxidation of gold and ammonia is to stabilize Cu(II) in alkaline solution. However, the presence of Cu(II) enhances the oxidative degradation of thiosulfate. The high consumption of reagents has made thiosulfate leaching uneconomical to date, in comparison with cyanide leaching. Therefore, further investigations are required to leaching under low reagent concentrations over extended periods where reagent consumption is low and gold leaching rate is low as well. It is thus necessary to find additives to enhance gold dissolution in the thiosulfate leaching system. Electrochemical studies using rotating gold disc showed that the oxidation of gold in ammoniacal thiosulfate solution increased significantly in the presence of a small amount of thiourea and the beneficial effect increased with an increase in the thiourea concentration up to 7.2 mM. Thiourea improved gold extraction in the thiosulfate leaching of gold from a sulfide ore under low reagent concentrations. Excessive addition of thiourea inhibited the leaching of the gold ore. The decomposition of thiosulfate was reduced with the presence of thiourea. X-ray Photoelectron Spectroscopy (XPS) results indicated that thiou-rea likely decomposed to sulfide and formed gold sulfide species at the gold surface.

Jan 1, 2014

By J. Qiu

By means of natural sedimentation, two different bentonite samples from Shandong province were purified, this paper studies the Hydro-properties of the two purified montmorillonite samples. Firstly, the layer charge of two purified montmorillonite samples were calculated by crystal structure formula reckon method and general hydro-properties were also measured. The research results showed that the layer charge of montmorillonite correlated well with its hydro-properties: mont-morillonite with lower layer charge had better hydro-properties, such as Mont-1, which had higher swelling volume and gelling value with lower CEC; while, montmorillonite with higher layer charge had worse hydro-properties, such as Mont-2, which had lower swell volume and gelling value with higher CEC; it proves that the hydro-properties of montmorillonite depends on its layer charge characteristics, layer charge characteristic is the inherent factors deciding the hydro-properties of montmorillonite, montmorillonite with lower layer charge has better hydro-properties than the one with higher layer charge. In this paper, the relation between the medium condition and colloid performance of Mont-1 are also studied. The results show that the hydro-properties of Mont-1 could be changed by changing slurry concentration (w/w) and shear rate or adding certain amounts of inorganic cation electrolytes, dispersants and surfactants. The viscosity of montmorillonite slurry could be enhanced by increasing slurry concentration,adding univalentcation electrolytes (less than 4% w/w) or proper amounts of dispersants and surfactants (less than critical micelle concentration); The slurry viscosity could be reduced by decreasing slurry concentration, increasing shear rate, adding proper bivalent (more than 4% w/w) cation electrolytes or proper quantities of dispersants and surfactants (more than critical micelle concentration).

Jan 1, 2014

By J. Finch, F. Rosenblum, McGill University

The self-heating of sulphides can be a major hazard in mining operations and concentrate handling, particularly during transportation and associated storage. Self-heating results from the oxidation of sulphide minerals and can vary from being insignificant to potentially hazardous to life and infrastructure. It is essential that there be a reliable test methodology that can categorize a given sulphide material as to its self-heating potential. By their nature, sulphide ores and concentrates are complex and variable mineral combinations making it difficult to predict their self-heating behavior a-priori based on mineralogy or with a simple "snapshot" test. Furthermore, self-heating behavior will depend on the state of oxidation of the sulphides as well as time, temperature and humidity. A review of available testing apparatuses and protocols that can be used to assess self-heating potential is presented. Each of these methodologies was examined in relation to its ability to predict the latent self-heating hazard of a sulphide material. Several of the methods were compared to illustrate their strengths and weakness. The results indicated that a number of the test protocols may produce false negative indications of self-heating potential, constituting an obvious concern to the industry.

Jan 1, 2014

This investigation addressed two products from Samarco?s desliming circuit, namely underflow of cleaning cyclones and underflow of desliming cyclones. The roughing cyclones receive the product of the grinding circuit. The underflow of the roughing cyclones feeds the cleaning cyclones and the overflow feeds the desliming cyclones. The underflows of cleaning and roughing cyclones are combined to constitute the feed of the flotation circuit. These fractions were characterized and a new process route was proposed. The size distributions of the two fractions are quite different. The desliming cyclones underflow presents higher amount of material passing 37 µm and of ultrafines as compared with the cleaning cyclones underflow. Laboratory scale flotation tests were performed in a mechanical machine aiming at comparing the performances of these products in the presence of the reagents employed in the concentrator. Pi-lot scale column flotation yielded enhanced iron recoveries for both products in comparison with those achieved in laboratory mechanical cells, without impairing the concentrate quality. The in-crease in recovery was more significant in the case of the cleaning cyclones underflow. These results suggest the use of columns in the flotation of this product aiming at increasing the overall iron recovery. Nevertheless the results also showed that the use of columns to float the cleaning cyclones underflow should also be taken into consideration. Despite the fact that this product requires a longer residence time in order that the required silica content in the concentrate is achieved, the indication is that higher levels of iron recoveries might be reached. The conclusion is that, due to the different behaviors of the two products, they should be processed in distinct circuits to maximize the iron recovery.

Jan 1, 2014

"A sulfide ore containing 2.19 g/t Au and 13.13 g/t Ag was studied for the deportment and extractive metallurgy of pay metals. The ore is composed mainly of non-sulfide minerals with approximately 10% pyrite and minor amounts of marcasite, chalcopyrite, galena, sphalerite, and arsenopyrite. The deportment study using a comprehensive approach showed that gold and silver minerals in the ore are mainly native gold (Au), electrum (Ag, Au), petzite (Ag3AuTe2), hessite (Ag2Te) and volynskite (AgBiTe2) with minor amounts of acanthite (Ag2S) and argyrodite (Ag8GeS6). At current grinding fineness (P70@150µm), the majority of liberated native gold and electrum particles are larger than 20µm with 85% >40µm, some of them are even larger than 150µm, indicating that extended leach time may be required to dissolve these coarse gold grains to completion and gravity concentration needs to be considered. Petzite is relatively fine with all liberated particles being less than 80µm in size. Gold distribution and leach testwork results showed that liberated gold accounts for 50% of the head assay, exposed gold associated with sulfide and non-sulfide minerals accounts for 30% and 11% of the head assay, respectively. Gold locked in sulfide and non-sulfide accounts for 4.8% and 4.1%, respectively. Thus, it is recommended that cyanide leaching be considered for extracting gold in this ore. This paper presents the detailed results of the gold and silver deportment study and extractive metallurgy testwork, and discusses the impact on process selection and flowsheet development.INTRODUCTION Gold and silver have been found in various geological environments and ore types. In terms of the gold deportment and extractability, gold ores can be classified into two categories and 12 types. Their extractive metallurgy is largely driven by mineralogical factors such as particle size, association with other minerals, coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of refractory gold minerals and locking of submicroscopic gold in sulfide and sulfarsenide mineral structures (Zhou et al., 2004; Marsden & House, 2006; Zhou, 2013a, 2013b). Compared to gold, silver mineralogy is more complex and metal extraction is more challenging due to its presence in over 200 Ag-bearing minerals (a silver-rich ore body would typically contain 5 to 10 different silver minerals) (Gasparrini, 1984), presence of refractory silver minerals (such as pyrargyrite, prustite and stephanite) and submicroscopic silver in sulphide minerals (such as galena and copper minerals) (Chryssoulis et al., 1985; Di Prisco et al., 2002). The presence of these issues often causes problems in Ag-bearing ore processing. Therefore, knowing the deportment of gold and silver in the ores and metallurgical products is important for flowsheet development and process optimization."

Jan 1, 2018

By A. Chattopadhyay

Porphyry copper deposits are the most important source of copper and also gold within the orogenic belts. These deposits are characterized by low grade copper ore (0.2% to 1% copper) and host precious metals like gold, silver and platinum. A characterization tool has been developed for complex porphyry type copper-gold deposits with an aim to quantify copper and precious metal deportment. This quantification is a challenging task due to low grades and also due to the presence of both visible and invisible precious metal content in different sulphide and non-sulphide phases. Studies were initiated on various complex, ore deposits and also on samples representing various processing streams such as flotation and leach products. This paper presents the development of a systematic approach to diagnostic metallurgy using state-of-the-art optical and automated mineralogy, micro-probe, dynamic SIMS and TOF-SIMS analysis for quantification of invisible and visible precious metals content in various species. The relevance of this characterization to metallurgy will also be briefly discussed in this paper.

Sep 1, 2012

The value creation with kaolin clays depends on removing the colored impurities which manifests in to higher brightnessone of the most sought after properties on applications such as paper coating, paint and others. The processes for removing impurities include magnetic separation, froth flotation and selective flocculation. While the flotation and selective flocculation processes exploit the physico-chemical differences between the surface properties, the magnetic separation uses the bulk magnetic susceptibility differences between the diamagnetic clay and ferro- and para-magnetic nature of the impurities. The major advantage with magnetic separation remains high yield and no or low reagent usage. However, the magnetic separation technology suffers from low separation efficacy when finer colored impurities (<1 µm) are encountered in the feed. Use of stronger magnetic intensities during magnetic separation showed limited success; nonetheless the adverse effect due to finer size range remains a dominant effect even at 5 Tesla magnetic field. Furthermore, the presence of diamagnetic colored impurities irrespective of their sizes can not be removed. Cytec Industries has recently developed a ?bolt-on? chemical enhancement technology for magnetic separation that essentially embraces the best product performance attributes of flotation and selective flocculation while keeping the chemical usage to a minimum level and using the readily available magnetic separation equipment. The paper will outline the technology and illustrate optimization work at pilot plant magnet on a wide variety of crude accommodating the process needs and plant limitations. The major advantages of chemical enhancement technology to magnetic separation include: 1) simple extension to existing magnetic separation technology, 2) ability to produce comparable product in quality with cost effectiveness compared to flotation and selective flocculation, 3) removal of impurity minerals over wide size range, 4) removing non-magnetic impurities, 5) providing robust process with high process yield and 6) operation-friendly nature. Furthermore, chemical enhancement technology for magnetic separation has also emerged as a platform for re-moving impurities at low levels in other mineral systems as well.

Jan 1, 2014

By L. Pan

As an air bubble approaches a mineral surface, a thin liquid film (TLF) is formed in between. The excess pressure (p) in the film determines the kinetics of drainage, which is of critical importance in flotation. We have developed a new method of monitoring the kinetics for both stable and unstable wetting films and analyzed the results using the Reynolds lubrication theory. It has been found that initially a TLF is thinned by the Laplace pressure (pcur) due to changes in bubble curvature and subsequently by the disjoining pressure (?) created by the surface forces present in a wetting film. In the present work, we have derived an analytical expression for determining ? from the temporal and spatial profiles of TLFs on mineral surfaces. The results show that ? > 0 in a film formed on a hydrophilic surface and ? < 0 in a film formed on a surface hydrophobized by collector. Thus, the role of collector in flotation is to create a hydrophobic force and hence a negative disjoining present in wetting films. It is also found that smaller bubbles can create higher Laplace pressure, which helps the TLF drain faster.

Sep 1, 2012

By D. P. Chakraborty

Joda East Iron Mine, one of the captive iron ore sources of Tata steel, located in the state of Odisha in eastern India caters to approximately 45% of the iron ore requirement of the Jamshedpur Steel Plant. The iron ore occurring in the mine having high in iron content along with high in alumina. Clay and gibbsite are the predominant mineral phases present as surface coating, fracture filling and/or free occurring and are responsible for alumina content higher. Alumina in iron ore impacts the techno-economic performance of a steel plant by impacting sintering and blast furnace productivity. The impact is even higher when it comes to fine ore used in the blast furnaces in the form of sinter as it constitutes a major portion of the blast furnace burden. Therefore, it is beneficial to upgrade iron ore in the mine head and to reduce alumina before it is subjected to agglomeration. Mineralogical test works reveal, that alumina in iron fines is mainly associated with the clay attached to the hematite particles, either free or interlocked to a very fine size. The paper describes the efforts made to reduce alumina in the iron fines in Joda East processing plant, without much of capital investment for a very sophisticated fines beneficiation circuit. In this process, a suitable dispersant was added in the plant that dispersed the masked slime coating over the iron ore fines, thereby making a better quality iron ore fines with reduced alumina content. The alumina in fines improved by 0.2 units? means from a label of 2.4-2.6 % reduced to 2.2-2.4 %. With this initiative, not only the primary objective of alumina reduction is met but also it has given substantial benefit in reduction of silica and as well as moisture in product. This moisture reduction also has given bottom line impact by reducing idle freight and royalty.

Sep 1, 2012

By Y. Foucaud, C. Eswaraiah, L. Filippov

Enhanced gravity separators such as Falcon concentrator which uses additional centrifugal force, are the most common gravity concentration techniques used for fine particles processing. Hence, understanding the kinetics and separation mechanisms within these separators is of paramount interest. Recent research yielded a predictive physical model for the Falcon Ultra Fine (UF) which however does not explain some results obtained with industrial ores. This study aims to identify the mechanisms involved in Falcon UF separation with the objective of confirming or rejecting the hypotheses on which the current model is built and suggesting potential points of improvement. The Falcon UF kinetics is investigated through the processing of complex low-grade and fine-grained ores from the Altenberg tin deposit (Germany), the Tabuaço tungsten deposit (Portugal) as well as a synthetic iron ore. Saturation tests are performed on the Falcon UF by controlling the separation efficiency in terms of recovery and enrichment ratio with time or feed mass. Results show an evolution of Falcon UF performance with time in contradiction with the stationary separation hypothesis on which the physical model is based. Observation of the concentrate bed suggests the presence of erosion figures in furrows which may play locally an active role in the separation. In terms of Falcon UF separation timing, three phases can be distinguished. First, upon initial feeding of the bowl, a bed quickly grows unselectively and ultra-fine particles are ejected from the bowl until the bed reaches its final profile. Next, actual separation occurs with selective concentration of dense particles. Finally, capture sites saturate and recovery drops. The evolution of partition curves over time confirms the existence of two separation mechanisms. First, differential particles settling within the flowing film responsible for the ejection of small size particles during the whole separation cycle which is already accounted for in the physical model. The second mechanism involved may be explained by the action of lift force, neglected in the physical model, which acts preferentially on coarse particles deposited at the surface of the bed resulting in coarser particles being rejected in the tailings. Hence, the addition of a lift force component to the existing model is suggested to account for this second separation mechanism.

Jan 1, 2018

By Y. L. Tian

Low-grade bauxite with A/S of 4.4 from Henan province was used as raw material and the selec-tive grinding of bauxite, grinding efficiency, particle size and Al2O3 and SiO2distributions of ground products were investigated using ball and vibration mills. The results show that the selective grinding can be used to realize the separation of aluminum from silicon within a certain particle size. The optimal grinding conditions of the ball mill with bauxite are as follows: grinding material to charge ratio, 1.2, charge volume ratio, 40%, pulp con-centration, 70wt%, medium size distribution, F30mm:F20mm:F15mm=20%:50%:30%. Under the conditions, the weight rate of ground product with A/S over 7.5 is 27% and the recovery of Al 2O3is 30%. The optimal grinding condition of the vibration mill with bauxite are as follows: grinding material to charge ratio, 0.9; charge volume ratio, 70%; concentration, 70%; medium size distribution, F40mm:F30mm:F20mm=20%:30%:50%. Under the conditions, the weight ratio of ground product with A/S over 7.5 is 25% and the recovery of Al 2O3is 27%. The research is significant for the rational and economical utilization of the low-grade bauxite.

Jan 1, 2014

By Yuhua Wang, Huilan Yang, Yanqing Jiang, Dongfang Lu

"Generally, the concentration of bauxite flotation tailings is around 10%, a large amount of water in tailings needed to be recycled in the flotation process. Sedimentation and dewatering properties of tailings were investigated under different conditions. Surface high negative charges on mineral particles are the key factor to destroy the settlement of tailings when the pulp pH is around 8.9. Hence, the modification of pulp pH around 7 is necessary to the diminution of the repulsive force between mineral particles and then the acceleration of sedimentation of tailings. Anionic polyacrylamine with molecular weight of 14 million is the best flocculant for the settlement of tailings in all tested polyacrylamines. P-toluene sulfonic acid shows better properties than hydrochloric acid for pulp pH adjustment when anionic polyacrylamine with molecular weight of 14 million is used as flocculant. Although the flotation of diaspore is depressed in the presence of polyacrylamine using sodium oleate as collector, but the recycling water traded by the combination of ployacrylamine and p-touenesulfonic acid does not show the depression effects on the flotation of bauxite ore. The lower residual content of polyacrylamine in recycling water treated by the combination of ployacrylamine and p-touene sulfonic acid plays an important role. INTRODUCTION Generally, the waste water generated from mineral processing plant is usually treated by sedimentation, oxidization, electrodialysis, ions exchange, active carbon adsorption and flotation technology, and the treated water is also used again in the industrial process. Flotation was adopted widely to improve the quality of bauxite from low grade diasporic bauxite in China. For flotation, the grinding fineness of bauxite is over 90% -0.074 mm, sodium carbonate and sodium hexametaphosphate were used as regulators, so the tailings pulp is very difficult to settle and be dewatered (Y. Wang et al., 2004; Y. H. Wang et al., 2007; Wang Yu-hua et al., 2008; Wang Yuhua et al., 2011). The water recycling of bauxite tailings are becoming the highlight for the industrial application of the flotation process for bauxite ore. Researchers in China shift their attentions onto this topic."

Jan 1, 2018

By V. I. Lakshmanan

The growing concerns on process efficiency, escalating operating and capital costs along with environmental and social concerns of using conventional technology for extracting gold and titanium dioxide demand an in-depth understanding of the fundamentals and a broader understanding of the various process steps involved. This will allow development of efficient process flowsheet for product recovery and compliance with regulatory guidelines. This paper will discuss our recent developments in mineral processing and hydrometallurgical technologies to recover gold and titanium dioxide from a wide range of feed materials including ores, concentrates and tailings.

Sep 1, 2012

By Mike Hollitt

The first decade of the 21st century was one of fundamentally changed dynamics for the minerals industry. Following intense globalization commencing in the late 20th century production is now concentrated into large businesses that can compete across geography in diverse commodities. Asian industrialization and urbanization is now the main driver of growth in demand for energy and materials. Demand for the output of these industries has risen sharply, reversing decade long trends to reduced real commodity prices. Supply responded with expansions of existing mining and processing operations, and large investment in new resource development. Development of new, lower grade or more remote resources was stimulated. Resource development by global entities in frontier environments reinforced the importance of effective forms of social contract, and of stronger environmental performance. The worst economic shock in decades provoked no significant pause despite large impacts on corporate ownership. State owned enterprises commenced unprecedented foreign direct investment in minerals and energy resources. A thrust towards resource nationalism re-emerged as governments sought to ensure that the export of state owned resources contributes more strongly to government revenue, reducing the burden of trade in scarce resources on other trade-exposed sectors. The unprecedented combination of forces at work has made future predictions difficult, with day-by-day volatility in anticipated corporate fortunes, and investment plans. The challenge for process innovation (and for exploration) has been to keep up, maintaining a lid on costs as lower grade and more challenging ore bodies are brought on quickly in a context of competition for land use, community expectations and continued care for natural and living environments. While new projects have provided the necessary platforms for implementation of innovative approaches, there is evidence that a gap may have emerged between the pace of growth and the pace of innovation. The history of a century of process innovation in the context of growth of output, declining resource grades and commodity prices is presented. The necessary conditions for accelerated process innovation are considered, and future needs and approaches are discussed. Keywords: process innovation, resource development

Sep 1, 2012

Traditional mineral processing techniques are more and more difficult to recover the increasingly low grade phosphate ores today. Although bioleaching method has been attempted to process low grade ores in hydrometallurgical field due to economical and environmental reason, it has been hardly used in leaching phosphate ore at home and abroad. Strains of Acidithiobacillus thiooxidans and Acidithiobacillus ferrooxidans were collected and separated from the acid drainage of a coal mine in Anhui province of China. Ultraviolet irradiation and Microwave inducement were applied to the bacterial cultivation process to produce strains of Acidithiobacillus thiooxidans and Acidithi-obacillus ferrooxidans able to tolerate extremely low pH conditions and generate sulphuric acid by oxidizing elemental sulfur or sulphide and the mutagenesis can achieve higher leaching rate. The bioleaching result will improve more by the addition of Tween series surfactants.

Jan 1, 2014

By Liu Jin

"In order to reduce the dosage costs and increase the economic benefits of a full floating process in a low grade complex multi-metals W-Mo ore, based on the study of the magnetic characteristics of the main gangue minerals, a joint process by magnetic separation and floatation technology is adopted. The first step of the flowsheet is to recover magnetite by magnetic separation, then remove the magnetic gangues by high gradient magnetic separation (HGMS) and finally recycle the W-Mo from the magnetically separated tailings by flotation. Results of the lab experiment show that in comparison with the full flotation process, the floatation feed tonnage of the combined flowsheet are only 46%. The grade and the recovery of Mo in the rough Mo-Bi concentrate is similar with the original one while the WO3 in the tungsten rough concentrate is increased from 3.85% to 6.64%. The dosage costs are reduced by 53%. The new process can significantly improve the plant economically. INTRODUCTION With the continuous exploitation of scheelite resources, the easily obtained resource is gradually depleting. The ""lean, fine and complex"" scheelite resource has become the main research object of tungsten beneficiation (Lou et al., 2010) (Xiao et al., 2013). The passive situation of tungsten beneficiation can be reversed by enhancing technological innovation and investment in science and technology, changing the business philosophy and mode of production, optimizing the process structure and process conditions, improving various technical indexes and reducing production costs of reagents, which will maximize economic benefits (Jiang et al., 2012 ) (Zhu et al., 2016). A polymetallic deposit of tungsten molybdenum bismuth original process adopts a full flotation process. With the expansion of stope mining, the content of valuable metals in the ore continues to decrease, resulting in a high cost per ton of concentrate produced and a low output value (Li et al., 2015)."

Jan 1, 2018

By I. A. Khabarova

The paper presents the results of experimental investigations of the effect by high-power nano-second electromagnetic pulses (HPEMP) on change of surface composition, physical-chemical and flotation properties of pyrrhotite, and search of optimal combination of flotation reactants providing increase of metal extraction from disseminated copper-nickel ores. Preliminary electropulse effect on products before flotation allows to create optimal conditions for flotation separation of pentlandite and pyrrhotite owing to forming the new phases and defects on the surface of sulphides. It was established, that the yield of monomineral fractions of pyrite, pyrrhotite and chalkopyrite increases by 5%~15 %, compared with flotation with one butyl xanthenes (BX), during usage of combination of thionic carbamate (isopropylmethylthionocarbamate (ITC) or isopropylethyl- thionocarbamate (Z-200) with butyl xanthate (BX). Sorption of investigated reactants and strength of their fixing on the surface of minerals are examined; it helped to reveal the cause of rise of floatability of sulphide minerals for the case of combination of reactants. Preliminary high-pulse processing and reactant conditions with usage of combination of thionic carbamate and xanthate have been tested on the sample of disseminated copper-nickel ore from Norilsk region.

Jan 1, 2014

By Juan B. Yianatos

"After almost 100 years, since the first commercial application began in Australia, flotation has shown an extraordinary growth and nearly 2 billion tons of ore per year are presently treated by flotation processes. During this time flotation has promoted a wide scope of research activities ranging from fundamental chemistry and hydrodynamic studies to studies of industrial operations. In general, fundamental studies have been mainly related to ideal situations. In recent years, however, large efforts have been focusing on achieving a better insight into the actual sub-processes provided by the development of new and more sophisticated instrumentation. Since the massive incorporation of flotation columns, around 15 years ago, a renewed interest in flotation fundamental studies, process modelling and new cell designs have been observed worldwide. The key role of the froth has been recognized as an independent and sometimes rate limiting process step. Thus, separation of pulp and froth process stages seems the most appropriate in terms of process modelling, diagnostic, design and scale-up purposes.In relation to flotation equipment development, until the middle of the 1970?s, only the sub-aeration mechanical cells were dominant. Since the 1980?s, the use of pneumatic cells and forced air mechanical cells has emerged strongly. Also, in the last decade, flotation equipment has shown a dramatic increase in size, reaching values of 200m3 in unitary mechanical cells and more than 300m3 in columns. The general feeling, however, is that, despite the great advance observed in terms of process knowledge, the mechanisms and principles of industrial flotation cells design and scale-up are still not fully understood.Advances in process instrumentation and control now in use allow for more efficient operations, both in metallurgical performance and savings in operating costs.INTRODUCTIONFlotation is a widely used process within the minerals processing industry, as well as being used for water treatment and de-inking of recycled paper. Froth flotation started in Australia at the beginning of the 20th century and since then flotation technology has made significant advances. Flotation was firstly applied to sulfide ores. The largest tonnages treated by flotation are copper and copper/molybdenum ores, handling about 50% of the total ore processed. Also significant are phosphate, iron ore and coal treatments. At present, Chile is the foremost copper producer in the world with around 35% of the world?s production. Figure 1(a) shows the evolution of copper production in Chile over the last decade. The total amount of fine copper produced in year 2001 was 4.7 million tons, from which 3.2 million tons was processed by flotation while 1.5 million tons went through LIX-SX-EW processes, which also showed significant development during the same period (Anon, 2001). The total flotation treatment of copper ores in Chile is about 325 million tons per year (Anon, 2002), so the world treatment of copper ore by flotation can be estimated at about 1 billion tons per year. Consequently a total of nearly 2 billion tons of ore per year is presently processed worldwide by flotation (Fuerstenau, 2001). In order to handle the higher tonnage of low-grade ore, a worldwide trend towards the development and use of larger flotation machines began in the 1960?s. Figure 1(b) shows that the trend became extremely marked from the beginning of the 1990?s, which is consistent with the strong increase in copper production during the same period."

Jan 1, 2003

By Z. G. Guan

The tungsten ore in Xingluokeng belongs to a symbiotic deposit containing granite and fine vein-type wolframite and scheelite. The tungsten (WO3wolframite) accounts for only 0.233% of the raw ore, 49.60% of the , 49.60% of the scheelite and 0.8% of the tungstite. The dissemination size of the tungsten ore is extremely uneven, with 0.02~1.28 mm for scheelite and 0.01~1.28 mm for wolframite. The dissemination size of scheelite is coarser than that of wolframite. The size of 83% of scheelite and 60% of wolframite is greater than 0.04 mm. The composition of minerals in the ore is quite complex. The major metallic minerals include wolframite, scheelite and pyrite, which are followed by molybdenite, chalcopyrite, arsenopyrite, limonite, magnetite, hematite and siderite. The major gangue minerals include quartz, feldspar, muscovite, biotite and sericite, which are followed by chlorite, fluorite, apatite, dolomite, etc. According to the dissemination features and liberation degree of the tungsten minerals, the technology flowsheet of gravity concentration for coarse particles and flotation for fine particles to re-cover the low-grade and fine vein-type tungsten minerals is adopted, and -0.7 mm is selected as the processing size. The closed-circuit grinding procedure, with the combination of the rod mill and high-frequency vibration screen, is adopted. The grinding product is classified into three products of -0.7 +0.2 mm, -0.2 +0.04 mm and -0.04 mm. The gravity separation is adopted for the former two to recover tungsten minerals and the flotation is adopted for the last one. Under the condition that the raw ore contains 0.23% WO3, some technology indexes of beneficiation have been achieved. The gravity tungsten concentrate contains 63.54% WO3 with the recovery 70.11%. The slime flotation tungsten concentrate contains 35.22% WO3 with the recovery 10.48%. The composite tungsten concentrate contains 57.53% WO3 with the recovery 80.59%. Thus, the tungsten minerals are re-covered effectively.

Jan 1, 2014

By Imre Gombköto, Zoltán Pap, Ákos Debreczeni, Sándor Nagy

Eddy current separators have become generally used in waste recycling industry during the last decade. There are many papers dealing with separation processes on eddy current separators, and also many article describes particle trajectory and different particle features affecting particle trajectory. These data are used in modeling as well. Within the frame of R&D project called ‚Fundamental research into the exploitation of the economic development potentials of critical raw materials in international co-operation - CriticEl?, authors are aimed for using Eddy Current Separator (ECS) as a mechanical separation step of high value critical elements recovery of selected WEEE’s like display panels, PCB’s. ECS, equipped with 305 mm wide belt, and a concentric magnetic rotor is used for experiments targeted development of methodology for determining separability of different particles on ECS. The subject of our work was to investigate the behavior of model particles with different shape, conductivity (aluminum and copper), orientation and size in order to separate Al and Cu according to the results of many experiments were carried out in this field. However it looks like that throwing distance of one particle is only possible to describe by a certain distribution for even the same particle within the frame of the same conditions. Sample mean and standard deviation are depending on some of the particle feature and acting forces. The paper is going to draft the first results on the relationship between distribution of throwing distance and particle properties.

Jan 1, 2014