Search Documents

By Francisco Cubillos, Jorge Menacho, Cesar Gomez, Juan Rodríguez

Mineral flotation is the most used process to selectively separate particles of one or more minerals of interest. The process uses natural or induced hydrophobicity to collect particles on the surface of rising bubbles through collisions and formation of bubble-particle aggregates. Flotation machines must keep particles in suspension and well distributed, while at the same time, disperse a mass of air into a population of small bubbles. The efficiency of the separation depends primarily on the characteristics of the bubble population generated in the machine and its distribution and flow throughout its volume. The formation and separation of bubble-particle aggregates create two zones, with strong interactions between them, and with markedly different hydrodynamics conditions. A model describing two-phase hydrodynamics of the continuous and dispersed phases (frother solutions and bubbles, respectively), moving along the whole unit, is proposed. Bubble populations are characterized at the formation stage including the effect of the presence of frothers. Flow through the aggregates formation zone, where bubbles move freely and are closely spherical, is modeled using drift-flux analysis. In the aggregates separation zone, bubbles initially pack maintaining a water layer thick enough to prevent capillary forces to affect their shape. As water drainage proceeds, bubbles deform, capillary channels form, and a network of channels with a diameter size distribution develops; channels become narrower (permeability is reduced) as the distance from the interface increases. Froth hydrodynamics is characterized using models originally developed to describe unsaturated flow through porous solid particle beds. Effects of hydrostatic pressure are considered.

Jan 1, 2014

By D. Tang

The froth zone in a flotation cell is recognised as a region which contributes to the overall flotation performance. Froth recovery is a measure of the efficiency with which the froth phase delivers particles arriving at the pulp-froth interface to the concentrate. Poor froth recovery in scavenger stages is generally attributed to poor froth stability. The key indicators of froth performance: froth recovery, entrainment and water recovery were measured in an OK3 pilot cell installed at a zinc concentrator in Australia and supplied with scavenger feed. Cell hydrodynamic and pulp chemical conditions during the operation of the cell were also measured as well as bubble growth across the froth phase. The objective of the work was to assess the impact of a number of commercial frothers on the froth performance in the OK3 cell and assess the suitability of using bubble growth as an indicator of froth stability.

Jan 1, 2014

By V. Buddhiraju

Liberation of valuable minerals from low-grade ores is an important challenge faced by the minerals industry. It is necessary to grind the ore to extremely fine size in order to liberate the mineral from such ores. As it is generally difficult to produce ultra-fine particles of diameter less than 1-10 mm using traditional grinding equipment such as the ball mill and the rod mill, several new types of grinding equipment are being explored to produce ultra-fine particles. The planetary ball mill is promising in that it makes grinding to submicron sizes possible by imparting high energy to the ground powder. It consists of four pots mounted on a disc. The pots and the disc rotate in opposite directions. The high-speed rotation of the pots and the disc makes the grinding media move at high centrifugal velocities leading to high impact energy and thus improving the grinding performance. The planetary mill is currently being explored for its capability to produce ultra-fine particles on a large scale. In this context, there is a need to understand the dynamics of the ultra-fine grinding process within the planetary ball mill. Here, we address this need by studying the movement of media inside the pots and the grinding kinetics, employing both experimental and modeling techniques. The experiments were conducted on a laboratory scale planetary ball mill. The particle size distribution of the powder was monitored to allow an estimate of the grinding kinetics to be made while video images of the media profiles inside the pots were taken to allow quantification of the media movement as a function of process variables such as the media size, percent loading, etc. The population balance modeling (PBM) framework was used to simulate the kinetics of grinding while the discrete element modeling (DEM) approach was utilized to simulate the media motion. The parameters in the population balance model, namely, the specific breakage rate and the breakage distribution function were determined by fitting the batch grinding equation to the experimental data. The predicted powder size distributions were found to be in good agreement with the experimental data. The experimental results have shown that the mean size of product powder decreases as the size of the grinding media decreases. Keywords: population balance modeling, grinding, planetary mill, grinding media, grinding equation

Sep 1, 2012

By Venugopal Tammishetti

One of the important technological challenges facing the iron ore industry in India is to find commercially viable technologies to process alumina rich iron ore fines and slimes. The key to solving this problem lies in developing selective reagents for the separation of iron oxide minerals from associated gangue minerals like quartz, gibbsite, kaolinite and montmorillonite. We present in this paper our successful results on the dispersion-flocculation of three different natural iron ore slime samples from mines in India using the reagent combination of PVP dispersant and corn starch flocculent. All the three samples contained hematite, goethite, kaolinite and gibbsite minerals as confirmed by X-Ray Diffraction (XRD) analysis. The effect of various process parameters such as pH, dosage of reagents, settling time and pulp density was studied. We were able to produce a concentrate assaying 66.2% Fe and <2% Al with a yield of 67.4% by weight (with a recovery of 77% of iron values) using PVP (1 ppm dosage) and corn starch (20 ppm) for one of the slime sample (Sample I) assaying 58.2% iron (Fe) and 3.8% aluminium (Al). The XRD analysis of settled and dispersed fractions revealed that alumina-containing minerals like clay and gibbsite mostly remain in the dispersed phase while iron-bearing minerals tend to concentrate in the flocculated fraction. Keywords: iron ore, slime, flocculation, dispersion, beneficiation, starch, polyvinylpyrrolidone

Sep 1, 2012

By H. C. E. Regidor, M. G. Mena, H. D. Mendoza

Cyanidation leaching has always been the most widely used method of extraction of gold in the world. Its low cost and high selectivity has made it the prevalent choice for mining companies, and even for the small scale miners. The use of cyanidation in small scale mining has been an issue for the longest time, mainly due to the operation’s lack of safety measures, health care or environmental protection regulations. In pursuit of more environmentally friendly methods of extraction of gold, several alternative extraction processes have been explored, one of which is chlorination. The chlorination process is advantageous when recovering refractory gold locked in sulfides, as it simultaneously oxidizes the surrounding sulfides as well as dissolve any gold exposed to the lixiviant. This research was conducted to study and develop a safer alternative way of extraction of gold from small scale mining operations, without compromising the recovery of gold. In this study, a variation of the chlorination process has been employed for a refractory flotation concentrate wherein the majority of the gold is locked in sulfides. Hypochlorite-bearing reagents were used as the leaching reagents, and the method developed was a 2-stage leaching process in differing pH conditions. The solution pH and Eh was monitored all throughout the runs, and aliquot samples were taken at time intervals for analysis. SEM-EDS imaging was used to determine the mode of oxidation of the chlorination process, and the image obtained showed that the oxidized layer followed the shape of the particle, suggesting a diffusion controlled process. XRD analysis of the sample before and halfway through leaching further confirmed the oxidation of the sulfides. The amount of gold dissolved in the aqueous solution and in the solid residue were used as the basis for the determination of the recovery of gold. An average gold recovery of up to 84.38% was obtained using the developed method in just 7 hours of leaching. This method was then employed for a pilot-plant scale test and a gold recovery of 79.2% was obtained.

Jan 1, 2018

By Wei Sun, Chengwei Li, Zhiyong Gao, Yuehua Hu

"Grinding for mineral liberation is a prerequisite for a successful flotation separation. Different grinding media produce mineral particles with different morphologies and surface properties. In this study, the surface physicochemical properties of fluorite particles produced by ball and rod mills were systematically investigated through single mineral flotation experiment, wettability measurement, X-ray diffraction (XRD) test and scanning electron microscopy (SEM) observations. The XRD observations reveal that the surface exposure degree for both mill particles follows the order {111} > {110} > {100}. The difference lies in that the rod mill ones have a higher exposure of more reactive {110} and {100} surfaces, leading to a stronger interaction with the collector. The difference also leads to their higher elongation and lower roundness values of rod mill particles which are beneficial for the particle-bubble attachment by shorting the induction time. The wettability and flotation results show that the rod mill ones have a lower critical surface tension and a greater hydrophobicity when treated with the collector solution and accordingly perform a higher flotation recovery. This work, for the first time, revealed the importance of the exposure of crystal surfaces in determine the shape factors and reactivity of the mineral particles and will help provide guidance for optimizing flotation separation and particle surface modification. INTRODUCTIONFluorite (CaF2) is the most important source mineral for producing F-based chemicals and materials which are widely used in industrial, environmental, and medical fields [1, 2]. In ore deposit, there are two kinds of occurrence forms of fluorite mineral. Firstly, the fluorite mainly coexisted with the gangue minerals like calcite (CaCO3) and quartz (SiO2). Because of their similar density and fine-grained dissemination in ore deposit, ball mill grinding before flotation separation has been widely applied to produce relatively fine particles [3]. Secondly, the fluorite is often associated with other valuable minerals with higher relative density such as scheelite (CaWO4) and cassiterite (SnO2). Due to their obvious density differences and coarsely grained distribution in ore deposit, rod mill grinding before gravity separation has been usually used to produce more uniform particles and avoid over-grinding [4-6]. After the gravity separation, a flotation separation is also employed to beneficiate the fluorite [7]."

Jan 1, 2018

By E. Yigit

In the flotation process the physical factors such as agitation intensity air flow rate and pulp solid concentration are very important parameters affecting grades and recoveries of the products. The flotation tests were performed on the samples of Bigadic colemanite ore to investigate these factors at different agitation intensities ranging from 1000 rpm to 1400 rpm and air flow rates from 1000 cm3 ? min-1 to 2000 cm3 ? min-1 with 2 L and 4 L cells using Denver laboratory flotation machine. The tested collectors were Cytec Aero 825, Aero 848N and their mixtures. Agitation intensity and air flow rises resulted in more floated material although sometimes being not selective. These effects can be attributed to powerful collisions between air bubbles and mineral particles. The first observation was the effect of pulp solid concentration on the floatability of minerals, while the flotation in 2 L cell (0.125 g.L-1 solid concentration) at 1000 rpm (0.176 wattcm-3), and with 1000 cm3.min-1 air flow rate was possible, the flotation in 4 L cell (0.0625 g.L-1 solid concentration at 1000 rpm. (0.176 wattcm-3) and with 1000 cm3 ? min-1 air flow rate was not possible. However at 4 L cell after increasing agitation intensity to 1200 rpm (0.201 wattcm-3) keeping 1000 cm3 ? min-1 air flow rate, flotation was possible again. This shows that these factors such as agitation intensity have some critical role on flotation. Another interesting observation was on the selective effect of pulp solid concentration. In the flotation with 1 L cell at different agitation intensities, collector Aero 848N was selective against calcite, while in the flotation with 2 L cell at different agitation intensities the same collector Aero 848N was selective against colemanite.

Jan 1, 2014

By Y. B. Zhang

China is rich in iron ore resources, but most of these ores are low-grade, polymetallic and refrac-tory ones. Furthermore, with the rapid development of chinese iron & steel industry, the comprehen-sive recovery of these ores is becoming more and more important. The tin, zinc-containing complex iron ores are typical polymetallic and intractable ones, and great reserves of them are found in China. At present, they have not been efficiently utilized. In this paper, based on the investigation of basic physicochemical properties of the tin, zinc-bearing iron concentrates, taken from a mineral processing plant, the mineralogy reason that these concentrates are so intractable and refractory is found out, using advanced microscopic testing methods, such as optical microscope (OM), Scanning Electronic Microscope (SEM), X-ray diffrac-tion (XRD), etc. It is found that the symbiotic relationship of iron, tin and zinc metallic minerals are very complicated, and magnetite in the concentrate is closely symbiotic or enwrapped by fine cassi-terite and sphalerite. So it is difficult to separate tin and zinc completely from the iron concentrates by simple regrinding and physical separation method. This investigation provides theoretical guid-ance for developing new approaches for utilizing these concentrates.

Jan 1, 2014

By Maurício Torem, Gabriela Huaman, Antonio Merma

The purpose of this review paper is to succinctly present the most significant works related to Mineral Processing and Environmental Bioremediation and developed by the Mineral and Environmental Technology Group (METG) of the Materials Engineering Department of the Pontifical Catholic University of Rio de Janeiro (PUC-Rio). In mineral processing it was emphasized the use of the Rhodococcus opacus bacteria as a bioreagent in the bioflotation of some mineral samples (magnesite, calcite, hematite, quartz and apatite). The adsorption of the bacterial cells on the mineral surface can be due to specific and/or non-specific interactions, which will depend on several factors, as their surface charge and hydrophobic character. The zeta potential evaluation of the mineral particles before and after interaction with the R. opacus cells showed that the biomass modified the zeta potential profiles of the minerals, which confirm the adsorption of bacterial cells on the mineral surface. Moreover, the bacterial cells adsorbed caused a change in the mineral flotability which is related to a change in their hydrophobic character, thus, the mineral bioflotability was found to be dependent on the pH and the bacterial concentration. On the other hand, the environmental bioremetiation assessed the biosorption potential of three metal ions (lead, copper, and cobalt) by four different biomass Streptomyces lunalinharesii, Rhodococcus opacus, Rhodococcus ruber and coconut shell powder. For this purpose, biosorption process was characterized under different operating conditions such as initial pH and biosorbent dosage. The Freundlich and Langmuir isotherm models were applied to the equilibrium data obtained at different concentration.

Jan 1, 2014

By L. Bbosa

Positron Emission Particle Tracking (PEPT) and the Discrete Element Method (DEM) are used to investigate Power Draw in a laboratory scale tumbling mill. The mill is run dry in batch mode at different speeds using mono-size charge of glass beads, and is mounted along with a torque transducer to measure power. Particle tracking information from PEPT is used to reconstruct the motion of glass beads and infer the overall charge behavior, while DEM is employed to simulate particle motion and interaction, with collision mechanics calculated using the Hertz-Mindlin contact model. For PEPT and DEM data, the product of torque and average angular velocities in discrete cells are accumulated to obtain mill power. This method is found to be within statistical agreement with measured power for all tests. Spatial distributions plotted from this approach highlight the regions of the mill that draw the greatest power. A second technique to obtain Power Draw from DEM data which sums particle forces against the mill geometry is similarly found to accurately predict mill power with lower statistical error. Keywords: Power Draw, PEPT, DEM

Sep 1, 2012

By J. Roth

The increasing demand of the filler industry regarding fineness and better delaminated products led to the development of a series of different grinding machines, which differentiate basically by the grinding mechanism as well as the kind of classification. Spiral jetmills grind, as it is well known preferably by delamination, therefore a spiral jetmill with integrated dynamic classifier has been developed. Especially the enhancement of the functional properties of the used industrial mineral fillers is a factor of highly increasing importance. These properties are very often bound to the platy shape of the minerals expressed by the aspect ratio. The developed Spiral Jetmill shows sufficient ability for such delamination and therefore increases in aspect ratio. In a series of comparative tests the suitability and advantages of this system regarding achievable fineness down to the submicron range as well as the conservation or even improvement of the aspect ratio of different minerals has been studied. As an emphasis on the results application tests with certain materials in the plastics field have been conducted. Due to the fact that in this range the required specific energy for achieving the necessary fineness increases exponentially another target is to optimize the grinding efficiency. A special feed control system provides on one hand a sufficient load inside the mill to obtain maximum utilization of the applied energy and on the other hand to prevent the mill from overfilling and coming with this a poor classification. The integrated classifier is a combination of a high speed motor with directly attached classifier wheels. This unit on one hand grants the necessary high circumferential speed of up to 190 m/s for providing an exact top cut of the ultrafine products and on the other hand gives the required operational reliability for continuous operation. Hard grindable impurities, which enrich inside the mill chamber, can be rejected from the process leading to an even cleaner product. Comparative tests on a talc product with certain free quartz impurities showed a significant improvement of the final product with respectively low loss on rejected material. This effect again had a beneficiary impact on the suitability of the final product when used in plastics application.

Jan 1, 2014

By F. S. Niu

With the feature of finely-dissemination particle and complex mineral composition, oolitic hematite is considered to be the ore dressing difficult problem in the world. Series research on refractory oolitic hematite in Zhangjiakou Area are introduced as following: ore properties?technology mineralogy and mineral processing technology. The survey shows: with the fine grinding of the hematite to a fineness of -0.076mm 95%, obtaining iron concentrates grading 62.74% Fe at the recovery of 46.80% by high intensity magnetic separation- reverse flotation flowsheet; under the three stages intensity magnetic separation,four stages grinding and four stages gravity separation, getting the iron concentrates grading 61.09% Fe at the recovery of 45% using high intensity magnetic separation- gravity separation flowsheet; with roasting temperature of 800°C, time for 75~90min and ore-coal ratio of 11, gaining the iron concentrates assaying 62.74% Fe at the recovery of 87% by roasting- magnetic separation flowsheet. At present, this research is still doing for the target of raising the concentration recovery on the base of high grade concentrate. It is in the hope of fully utilizing the existing hematite resources in Zhangjiakou

Jan 1, 2014

By S. Patra, R. Venugopal

"The quality of pellets produced is affected by quality anssastd quantity of green pellets, amount of addition of binders, type of binders added, amount of moisture added along with the other variables like rotation, inclination and fineness of feed. The green pellet quality depends upon chemistry, mineralogy and granulometry of fines used for pellet making, the feed size, its moisture content and porosity. During firing of green pellets ingredients present within reacts to form different phases and microstructure. So in turn physical and metallurgical properties of pellets are influenced by amount and type of binder and flux addition, induration time and temperature. During iron making process, the metallurgical properties of fired pellets are decided by the type and amount of these phases and their chemistry. Green pelletizing and induration studies have been already carried out with hematite ore fines. Indian iron ores of high alumina content showing different pelletizing characters, these studies can’t be directly interpreted. The main objective of proposed research work is to understand the green pelletizing process and determine the water bentonite interaction at different levels. Detailed investigation on swelling behavior of bentonite and microstructure of the green pellets of iron ore fines from SAIL captive iron ore fines from the Barsua in the state of Odisha. To convert these ore fines into pellets, the key raw material, additives and process variables that influence the pellet quality needs to be identified.INTRODUCTION Pelletization is the unit operation of agglomerating iron bearing fines (generally below 150µ with 65-80% passing 40µ) by tumbling in horizontal rotating drums or inclined discs, (Sivrikaya and Arol, 2013; Bhuiyan et al., 2011; Forsmo et al., 2006; Sastry et al., 2003) and the pellets are approximately spherical lumps formed by this process in presence of water and binder, on subsequent induration at 1300°c (Sivrikaya and Arol, 2014; Sivrikaya and Arol, 2013; Sivrikaya and Arol, 2012; Sivrikaya and Arol, 2010; Sastry et al., 2003; Kawatra and Ripke, 2003; Iveson, 2001a; Iveson, 2001b)."

Jan 1, 2018

By E. V. Konoplev

Russia is one of the largest manufacturers of potash fertilizers in the world. Processing of potash ores basically is carried out by a flotation way. Potash ores of the Verhnekamsky potash deposit contain sylvite (KCl), halite (NaCl) and water insoluble impurity (up to 8 %), presented silicate- carbonate minerals, easily slimed by ore crushing in rod mills. Ore of some deposit sites, developed by ?Uralkali? Co, contains a significant amount of a carnal-lite (KCl.MgCl2.6H2O). Work practice of flotation potash plants has shown, that increase of car-nallite content in ore leads to increase magnesium ion content in a circulated plant brine (saturated salt solution of potassium and sodium chlorides-sylvite brine) and to deterioration of indicators of ore processing. In the Paper we present results of researches of floatability of various size sylvite and influences silicate-carbonate slimes on sylvite flotation in brines with the various magnesium chloride content. It is established, that with increase magnesium chloride content in the brine mainly decreases the flotation of coarse sylvite and amplifies adverse effect of silicate-carbonate slimes on sylvite flotation. In this connection deterioration of potash ore flotation is caused not only decrease sylvite floatability but also strengthening adverse action of water insoluble impurity on potash flotation. It is shown that the application of frothing agents, which render the stronger dispersive action on the colloidal-micellar structures of amine in the salt solution increases the absorption of collector on the sylvite and improves the flotation of sylvite into magnesium the containing salt solutions. The application of an organic depressor to the greatest degree of decreasing the absorption amine on the slimes and to the smallest degree possessing anionic properties proves to be most effective with the flotation carnallite of the containing potassium ores. It is offered the application the frother on a basis of glycol ethers and organic depressor on a basis of urea-formaldehyde resin. Results of industrial tests developed reagent modes for flotation treatment of ores with the raised carnallite content (to 6 %) on ?Uralkali? Co plant have shown that their application has allowed to receive equivalent indicators potash flotations at change of magnesium chloride content in the brine from 0.7 % up to 2.4 % .

Jan 1, 2014

By J. Vilcáez

The copper extraction yield from thermophilic bioleaching of chalcopyrite depends on temperature, pH, and the oxidation-reduction potential (ORP), as well as the activity of the microbe used. We studied copper extraction yields obtained from chalcopyrite with three thermophiles, Acidianus brierleyi, Sulfolobus metallicus, and Metallosphaera sedula, under various pH and temperature conditions and with different initial amounts of ferric iron. The results indicated that the capacity of each thermophile strain to leach iron as Fe3+ differed, which affected the influence of pH, temperature, ORP, and microbial activity level on the yield of copper. Microbial activity can cause ORP to be close to the critical value (450 mV) at which copper extraction at 65 °C can be higher than that at 80°C. An initial pH of 1.5 retards the precipitation of jarosite, allowing temperatures as high as 80°C to result in copper extraction yields close to 100%. However, if a thermophile with a poor capacity to form Fe3+ is employed, 100% copper extractions can also be obtained at pH 2.5, because ORP is low as result of low amounts of Fe3+ in solution. Optimum temperatures for the growth of thermophiles did not always mean high copper extraction yields. Conversely, high biomass concentrations depending on the capacity of the thermophile strain to leach iron as Fe3+, can result in excess Fe3+ in solution, leading to the precipitation of large amounts of Fe3+ as jarosite. The bioleaching capacity of A. brierleyi was reduced or suppressed when insufficient initial Fe3+ was pro-vided to trigger the leaching reaction, whereas S. metallicus and M. sedula were less sensitive to the initial availability of Fe3+. This result confirmed that a direct enzymatic attack on the mineral surface could initiate the leaching reaction, but later ORP governed the leaching rate of chalcopyrite.

Jan 1, 2014

Flinders Power, formerly NRG Flinders, is considering the possible use of low rank coal from Lake Phillipson, South Australia (SA) in its power stations at Port Augusta, SA. Typically, this coal contains about 35% moisture and 10% ash. Unfortunately, it also contains high levels of sodium (1% Na) and chloride (0.95% Cl) with a Na2O level in ash of 18.9%. Such levels cause serious problems during coal combustion, making the use of as-mined coal impractical for power generation. This paper describes the development of an aqueous leaching technique to remove 90% of the sodium and chloride and to yield a product with a Na2 O level in ash of less than 3%. Small-scale agitation leaching tests with good quality tap water at ambient temperatures showed that the coal needed to be crushed to minus 5.6 mm to obtain maximum removal of water-soluble sodium and chloride in 30 min. Leaching kinetics, but not the ultimate removal of salt, were enhanced by the use of higher temperatures (up to 150°C), but this was deemed uneconomic. Varying the pulp density between 20% and 50% had little effect on extractions and there was no benefit in multiple stage water washing. The best results by water leaching were 69%~74% extraction for sodium and 95%~97% for chloride, meaning that the sodium removal was well below the target level. From SEM examinations of the leached product it was concluded that the remaining sodium was organically bound to the carbon atoms in the coal. Further tests using aqueous solutions containing cation exchange additives such as calcium chloride (CaCl2) or ammonium chloride (NH4Cl) or sulphuric acid (H2SO4) showed that significantly enhanced sodium extractions were possible and target specifications were met. Two options, namely a single-stage and a two-stage leach, were then investigated. In a single-stage leach with additive, minus 5.6 mm coal was leached at 33%~50% solids for 30 min at ambient temperature and then filtered and washed with fresh water. This gave a sodium removal level of about 81% and a Na2O level in ash of about 5%. These levels do not quite meet tar-get specifications. In a two-stage leach, the coal was first leached with water alone without an additive as in the single stage leach, and the washed residue re-leached under similar conditions for about 5 min with an additive (CaCl2), and then filtered and washed. This gave a cumulative sodium removal of 96% and a Na2O level in ash of 1.4%~2.4%. These levels are well within target specifications.

Jan 1, 2014

By B. P. von der Heyden, P. Neethling, M. Tadieb, L. Babedi

The effects of trace element substitutions in sphalerite mineral structure on optimised floatation response have, as yet, not been fully constrained or fully understood. To further this important field of study, this contribution focusses specifically on mineral and surface chemistry, and electro-chemistry of Cd- and Co- substituted synthetic sphalerites using Raman spectroscopy and Zeta potential experimentation. Raman spectroscopy illustrates that the presence of these impurities results in the introduction of a new mode, the relative intensity of which can be correlated (Cd r2=0.95 and Co r2= 0.99) to the dopant concentration. Comparison to X-ray Diffraction results measuring the unit cell parameter further shows that this relative intensity (Cd r2=0.81 and Co r2= 0.99) may provide insights into the degree of lattice strain within the mineral structure. The zeta potential distribution of an un-activated Cd-sphalerite show no detrimental effect as function of Cd content. Although the iso-electric point shifted from 2.45 at 1 wt.% Cd to 2.69 at 3.68 wt.% Cd, the zeta potential remained negative at alkaline media. Conversely, cobalt at low concentration of 0.36 wt.% had a detrimental effect on the surface charge, resulting to a close to neutral zeta potential at different pH. The adsorption of Cu ions on the surface of Co-bearing sphalerite conditioned in an alkaline media slightly increases the zeta potential of Co-sphalerite. While the Cd-bearing sphalerite decrease in negative zeta potential at >1 wt.% Cd indicating a complete exchange between Cu and Zn. The results presented herein illustrate that, based on the chemical nature of the substituting metal; sphalerite will exhibit multiple response to flotation reagents. Maximum recovery of zinc can thus only be achieved through multidisciplinary study and fundamental understanding of the effects of cation substitution on mineral structure and surface chemistry, the latter necessarily affecting the floatation response.

Jan 1, 2018

By A. Qaredaqi, M. Mohammadi

Wet High Intensity Magnetic Separators, for short, WHIMS are used for recovery of Iron ores with low magnetic susceptibility. A Jones patent WHIMS with "grooved plates" matrix is being used in Dry Tailing processing line in Hematite Recovery Plant at Golgohar mining & Industrial Co. for recovery of Hematite. In this kind of separators Matrices are used for increasing the Magnetic field intensity and providing high magnetic field gradient. The laboratory WHIMS in Golgohar Iron Ore and Steel research Institute is capable to provide a background magnetic field strength up to 0.85 Tesla and in presence of ‚expanded metal? matrix, magnetic field intensity could increase up to 0.9 Tesla. More than 50% of feed particles in this separator were finer than 36 micron and recovery of these particles needs more magnetic field intensity. Hence, ‚Grooved Plates? matrices with Js= 2 Tesla and 3.8 mm gap were constructed. Measurements indicated that magnetic field intensity around the matrix will increase to 1.25 Tesla. Graph of Magnetic field intensity around the matrix to background magnetic field intensity was plotted and a model with Rsquare= 0.9 was offered. In addition, magnetic field gradient and magnetic force were calculated. In WHIMS with feed top size of 150 micron, the main effective forces on separation process are the magnetic force and the hydrodynamic drag force. With assuming that the particles are smooth and spherical and the flow is laminar, Recovery of fine magnetic particles is problematic in this separator because of drag force. Considering these facts and mentioned model, finest particles that are recoverable in different magnetic field intensities were calculated. Computations illustrated that with magnetic field intensity more than 0.8 Tesla, particles as fine as 4 micron are theoretically separable but it should be noted that in practice a larger attractable particle size would be expected.

Jan 1, 2014

By W. Y. Gao

Diaojuntai Concentrator adopts a process of low intensity and high intensity magnetic separation and anionic reverse flotation, with all the concentrate from magnetic separation being treated by re-verse flotation to obtain a qualified final concentrate. The high reagent cost and energy consumption of the reverse flotation have led to a high concentrate cost. The test research on reducing the feed to the reverse flotation was therefore carried out. Based on the study of the properties of the ore sample, the concentrate of low intensity magnetic separation was screened at 0.076 mm and the undersize fraction was concentrated by concentrator with gravity and magnetic field. The results show that a qualified concentrate can be obtained at various rising current rate, pulsating current and power-on style, with the operation rate over 85%. The extraction of some part of qualified concentrate from the concentrate of low intensity magnetic separation by magnetic separation can reduce the feed to the reverse flotation by about 35% so as to reduce the production cost of concentrate.

Jan 1, 2014

By D. J. Zhao

The reduction of ilmenite pellets was investigated at 950°C and 1000°C under a CO-N2 gas mixture with 10 L/min gas flow rate. All the reducing reactions were conducted in a furnace with a thermogravimetric analysis system. The reduction rate is higher at 1000°C than that at 950°C. At the early stage of the reactions, with the CO concentration increasing in the gas mixture, the reduction rate increased at 1000°C. In addition, at the early stage of the reactions, a rapid temperature increment and a rapid conversion of oxygen were observed on the curves of temperature versus time and conversion of oxygen versus time under different experimental conditions. The solid reaction products obtained in these experiments were analyzed by Scanning Electron Microscopy (SEM) and Energy Dispersive Spectrometers (EDS). Metallic Fe with small amount of Ti dissolved in it and oxides of Ti were found in the solid reaction products, but the formation of any nitride phases was not found under the prevailing conditions.

Jan 1, 2014