Search Documents

By T. Inoue, K. Okaya

"Movement of mill charge in the centrifugal mill is essentially different from that in the vibration mill with circular path despite the apparently similar mode in the motion of mill body. As proved e.g. in [11], this results in substantial advantage regarding the comminution intensity of the centrifugal mill over the conventional vibration mill accounting approximately to one order of magnitude.Back in 1983, Bradley et al. presented a model of the centrifugal mill based on the kinetics of the mill charge by regarding it as a lumped mass. On the other hand, numerical modeling by ‘discrete element method (DEM)’ enabled us to observe the movement of each ball in the centrifugal mill with an extremely minute time intervals (Inoue et al., XX IMPC in 1997). The former approach rendered simple, even though approximate, expression of the mill behavior, while the latter method was advantageous in describing the behavior of the mill in terms of individual events taking place in the mill body, even though the result did not reduce to a simple expression. The characteristics of the centrifugal mill described by both these approaches proved to be in a degree of agreement. Thus, the kinetic approach was capable of presenting the overall view of the mill, while the DEM model was informative of the details that could not be depicted well enough by the simple math expressions."

Jan 1, 2003

By J. Jirestig

Poor grade iron ore, suffering from interlocked particles, is challenging for any process technology. Extensive grinding is required to attain liberation and to yield concentrates of desired grade. Fine particles are commonly very difficult to retrieve, resulting in value losses to tailings. In this paper, results from HGMS tests on fine to ultra fine hematite are reported. Special emphasis is put on slurry flow velocity. If hydrodynamic drag force, i.e. flow velocity is not controlled and kept constant during the feed and/or rinse phase, fine particles will not be captured and retained. Flow velocity control and constant flow during separation are achieved by discharge valves/slots and parallel magnetic flux and pulp flow configuration. In tests, increased slurry velocity from 178 to 268mm/s caused Fe-recovery to drop from 78 to 48%. Proving that flow velocity control is essential to optimise grade and recovery. HGMS tests at the Metso mineral laboratory on natural (weathered) hematite fines clearly show a large potential to recover valuables, currently lost to tailings. Even at particle size distributions as low as D80=35µm concentrate grades and recovery are very satisfying. Two samples, in-plant desliming rejects (D80=35µm and 50µm) where significantly upgraded and recovered, from 45,3% to 63,6% and 53,0% to 63,4% Fe, at 73,8% and 81,1% Fe-recovery respectively. Other types of in plant rejects, such as gravity separation or WHIMS tailings, also benefits from HGMS separation. Gravity separation reject, 55,8% Fe, at D80=500µm was tested, yielding a magnetic concentrate of 60,8% Fe at 50,7% Fe-recovery. The results indicated that the hematite was poorly liberated. HGMS separation was repeated after a regrind to D80 150µm, resulting in a magnetic concentrate of 62,8% Fe at 75,9% Fe-recovery. The tests prove that hematite, presently lost to tailings streams, can be recovered by HGMS and thereby significantly contribute to improved overall economy. Keywords: HGMS, magnetic separation, recovery of ultra-fine hematite, Indian hematite ores, hematite recovery from tailings

Sep 1, 2012

By A. O. Gapchich, T. N. Matveeva, N. K. Gromova

"Tin sulfide ores and aged man-made products obtained after their processing are distinguished by a complex material composition and uneven impregnation of sulfide minerals (chalcopyrite, galena, arsenopyrite, etc.) and tin ore (cassiterite). Enrichment of such ores is performed through sophisticated multistage schemes using not only gravitational methods, but also gravity flotation, flotation, magnetic separation techniques. Tin ores also contain rare and precious metals (indium, scandium, silver), characterized by fine dispersity and microscale to nanoscale fineness of mineral formations. During flotation concentration these metals are extracted along with the main ore minerals into concentrates (tin, copper, tungsten, etc.), however, up to 10-20 % of them are lost with final tailings. The aim of the work is an experimental study of the modification of the surface of sulfide minerals and cassiterite by stable metal-collector complexes to increase extraction of fine tin, silver, copper and other metals from complex tin ores. Triamide cyanuric acid (TCA) was studied as a thin silver flotation modifier. Thermophilic polymer with a functional group of phenylphosphine TMPPh was used as a selective flocculant. For experimental studies of the physical and chemical effects of collecting agents on the surface of minerals the following analytical techniques were used - the analytical scanning electron emission ASEM (LEO 1420VP INCA OXFORD ENERGY 350) and laser (KEYENCE VK-9700) microscopy, measurements of electrode potentials of mineral anthills by potentiometric titration, monomineral and pulp flotation. New data on formation of the adsorbed layer of DBDTC on the surface of chalcopyrite, galena and arsenopyrite were obtained, and the dimensions of the reagent films and the strength of their adsorption. The indiscriminateness of cassiterite to DBDTC ensures its selective separation into a chamber product during the flotation of sulfides. It is shown, that modification of the sulfide surface by stable complexes Me-DBDTC and Ag-TCA-TMPPh will increase the recovery of non-ferrous metals and silver into a collective sulfide concentrate and will provide a high-quality tin concentrate for flotation of tin sulfide ores.The studies were perfomed with the aid of the Russian Science Foundation (Project No. 17-17-01292).INTRODUCTIONTin sulfide ores and aged man-made products obtained after their processing are distinguished by a complex material composition and uneven impregnation of sulfide minerals (chalcopyrite, galena, arsenopyrite, etc.) and tin ore (cassiterite). Enrichment of such ores is performed through sophisticated multistage schemes using not only gravitational methods, but also gravity flotation, flotation, magnetic separation techniques. Tin ores also contain rare and precious metals (indium, scandium, silver), characterized by fine dispersity and microscale to nanoscale fineness of mineral formations. During flotation concentration these metals are extracted along with the main ore minerals into concentrates (tin, copper, tungsten, etc.), however, up to 10-20 % of them are lost with final tailings. In this regard, it seems advisable to use new varieties of flotation reagents in order to increase extraction of finely dispersed tin, silver, copper and other non-ferrous and precious metals from multi-metal tin ores (Bocharov and Ignatkina, 2007; Khanchuk etal., 2012; Wu and Zhu, 2006; Yusupov etal., 2016)."

Jan 1, 2018

By O. V. Suvorova, V. G. Minenko, D. V. Makarov, A. L. Samusev, E. A. Selivanova

"Saponite is a valuable marketable product widely used foundry, metallurgy and construction, in the chemical, food and consumer goods industries, in medicine, and in agriculture.The feasibility of producing of high-quality construction materials with enhanced physical-chemical and decorative characteristics from saponite-containing products has been given a scientific basis and experimentally validated. The compressive strength of the samples in the sintering temperature range of 800-1000 ?? varied between 35 and 80.9 MPa; the bending strength 8 and 26.7 MPa, which is superior to the high-grade ceramic bricks of the M-300 brand. It has been established that the saponite-containing product obtained using the electrochemical separation of process water has a high sorption capacitance relatively the heavy-metal ions such as nickel and copper (40.7 and 99.8 mg/g, respectively). As a result of sintering at 750 ?? the sorption capacity of the sorbent for the nickel and copper ions increased to 194.2 and 212.8. Using the XRD and SEM with energy-dispersive spectroscopy studies, we diagnosed the metal-containing phases and validated the metal sorption mechanism.This study opens up the possibility of practical realization of the saponite-containing product as high-quality building materials and heavy-metal sorbents while addressing the issue of process water treatment. INTRODUCTION The Lomonosov deposit of the Archangelsk diamondiferous province accommodates 10 kimberlite pipes. The anticipated volume of diamond-bearing ore and dump rock to be removed before reaching the open-pit mining limit is 300 mln t (Karpenko, 2009; Bezborodov, etal. 2003). Rock in the deposit is almost completely displaced by clay minerals, predominantly saponite, amounting to 90% in the vent facies (Karpenko, 2009)."

Jan 1, 2018

By W. H. Yong

The molybdenum ores currently utilized in China are mostly molybdenum sulfide ores, whereas oxidized molybdenum ores have not been exploited and utilized efficiently. The aim of this article is to study the applied mineralogy of an intergrown iron-molybdenum oxidized ore in order to provide a mineralogical basis for the ore beneficiation research. The ore occurred in a surface oxidized zone seam and contained 23.65% Fe2O3 and 1.58% Mo. Various characterization techniques were employed to study the chemical composition and mineral composition of the ore, the particle size distribution of the minerals in the ore, and the tex-ture and structure of the ore. The results showed that the iron-molybdenum ore occurred in a wet, soft and earthy state. The ore was composed mainly of several oxidized minerals and colloidal min-erals, including wulfenite, barite, limonite and quartz. Wulfenite was one of the major and stable components in the ore and occurred as a separate mineral. Wulfenite, barite and quartz were granu-lar minerals with particle size ranging from fine to coarse but mainly in the fine particle range. Li-monite showed a crust and honeycomb-like colloidal state and composed the framework in the ore for the formation of the other minerals. They filled the pores in the framework and the size of the pores affected the size of the minerals formed in the pores and hence the recovery of wulfenite in ore beneficiation. According to the applied mineralogical properties of the oxidized molybdenum ore, a promising ore beneficiation process was proposed as follow Magnetic separation should be carried out first to separate the magnetic iron minerals and then the molybdenum mineral will be recovered by gravity concentration or a combination process of gravity concentration and flotation, depending on the distribution of the molybdenum mineral in the product of the magnetic separation.

Jan 1, 2014

By Ingvar Ymén, Anders Sandc, Jan Rosenkranzc, Lisa Malma, Ann-Sofi Kindstedt Danielssonb

The understanding of particle surface properties is essential for the study and evaluation of froth flotation phenomena, particularly in the investigation of various chemical or reagent effects. Dynamic Vapor Sorption (DVS) is a method used for the analysis of surface properties of powders for instance in the pharmaceutical industry. To the knowledge of the authors, it has however not been used before in applications related to mineral processing. The DVS technique involves measurement of the water uptake of a relatively small amount of sample as a function of the relative humidity (% RH) in a temperature-controlled environment. The purpose of this work was to evaluate the method and investigate how it can complement existing techniques for surface characterization in mineral processing. Four samples (feed, CuPb concentrate, Cu concentrate and Pb concentrate) from the Cu – Pb flotation process in the Garpenberg concentrator, Sweden, were analyzed by DVS and the traditional capillary absorption technique (Washburn capillary rise). This enabled comparison between the two methods and evaluation of their respective advantages and disadvantages. Both methods give the expected ranking of the hydrophobicity for CuPb concentrate, Cu concentrate and Pb concentrate, but a discrepancy was observed for the feed. Washburn gave a value for the contact angle which was in the same range as for the CuPb concentrate, whereas DVS gave a value for the moisture uptake which was much higher than for the CuPb concentrate. Thus, DVS ranks all samples correctly, but with an unexpectedly high value for the feed whereas Washburn gives good ranking for three samples out of four. Potential reasons for the discrepancies are discussed.

Jan 1, 2018

By Güven Önal, Gülay Bulut, Mustafa Özer, Yunus Emre Benkli, Olgaç Kangal, Mustafa Tarkan

There are various types of natural zeolite deposits in Turkey. Naturally occurring zeolites are excluded from many important commercial applications where uniformity and purity are essential. In this paper, the beneficiation of natural zeolite, taken from western part of Turkey, was investigated. According to X-Ray Diffraction (XRD) and mineralogical studies carried out on the representative ore sample, the natural zeolite was found to be in the forms of clinoptilolite and heulandite. Clinoptilolite forms as a devitrification product of volcanic glass in tuffs. Quartz, clay minerals, orthoclase, plagioclase, biotite, seruzite-muskovite and epidote were observed as impurities. Several types of mineral processing methods were performed in order to remove impurities from the natural zeolite sample to produce high purity zeolite. Gravity separation methods such as shaking table and superpanner were carried out for separating heavy minerals, while high intensity dry magnetic separation was used for discarding magnetic minerals.

Jan 1, 2003

By I. S. M. K. Ilankoon

In heap leaching the transport of the acid from the drippers to the surface of the ore particles is a major factor in the overall performance of a heap. This flow behavior is complex as the flow is unsaturated and occurs along a tortuous set of inter-particle channels and connections. Previous modeling of this system has used equations from oil and ground water flow to model these systems, but the applicability of these models with the larger particles found in typical heaps is suspect as these systems are not necessarily capillary dominated. In particular, as the characteristic particle size goes from below to above a few centimeters, the flow changes from capillary to gravity dominated. This means that typical heap leaching heaps cover this interesting, but complex, transitional fluid flow regime. In this paper a set of experimental studies of this flow, including PEPT (positron emission particle tracking) based tracer experiments, highly accurate liquid holdup measurements and axial dispersion experiments using salt tracers will be presented. In this study, flow through mono-dispersed particle beds was carried out. In particular, the hysteresis in the liquid holdup as the liquid flow rate into the particle bed is varied is investigated, since this hysteresis means that the relationship between flow rate and holdup is history dependent, an effect not included in models currently used to describe fluid flow in heaps. A theoretical model that describes this hysteresis will also be presented. Keywords: heap leaching, hydrometallurgy, modeling

Sep 1, 2012

By D. H. Xiong

Low grade oxidized iron ores are usually not economic to utilize. However, the development of SLon magnetic separators and other new technologies make the process cost lower and lower. In this paper, several low-grade oxidized iron ore process flowsheets are introduced. The key procedure is that at the early stage, SLon magnetic separators are applied to discharge as more tails as possible with very low cost, only a small portion of rough concentrate going to the cleaning stage, showing the new technologies are profitable for such iron ores.

Jan 1, 2014

By Guanghua Ai, Xiong Huang, Huashan Yan, Ting Li, Tingsheng Qiu

"Cyanide tailings of gold and silver concentrates contain considerable quantities of copper-lead-zinc sulfide minerals that can be recovered. However, the strong inhibition effect of cyanide often makes it difficult to recover these sulfide minerals effectively. In this research, a sample of cyanide tailings was investigated based on the principles of process mineralogy; activating flotation tests were carried out for the target minerals in the tailings, and the activation mechanism of the activator and its influence on the target minerals were investigated by Fourier transform infrared spectroscopy (FTIR). Mixed flotation of copper and zinc was carried out using QJ-01, a combined agent containing sulfite, as the activator of copper and zinc minerals, and ammonium dibutyl dithiophosphate (ADD) and butyl xanthate (BX) as the combined collector. Copper concentrate was obtained from the mixed concentrate by using a combined inhibitor of sodium sulfide and zinc sulfate to inhibit the zinc mineral. Zinc concentrate was extracted from the copper tailings by using copper sulfate as the activator and BX as the collector. The flotation test yielded copper concentrate with a grade of 22.56% and recovery of 76.96%, and zinc concentrate with a grade of 42.56% and recovery of 82.29%, which shows that comprehensive recovery of the sulfide minerals – copper and zinc –from the cyanide tailings was realized. The FTIR analysis showed that CN- was chemisorbed on the surface of chalcopyrite and sphalerite following cyanide treatment, while the combined activator QJ-01 containing sulfite reduced CN- into SCN- and weakened the complexing ability of CN- with metal ions on the mineral surface, thus achieving a good activation effect on chalcopyrite and sphalerite. The results of this study can provide practical guidance in increasing the resource utilization ratio of cyanide tailings in gold mines, and thus contribute to alleviating environmental problems caused by stockpiling cyanide tailings. INTRODUCTION Cyanidation, the most widely used technology for extraction of gold, has several advantages such as high recovery, process maturity, low cost, etc. According to available data, the annual discharge of cyanide tailings from China's gold mines exceeds 20 million tons (Li et al., 2011). Lower grades of exploitable gold ore entail increased discharge of cyanide tailings. Huge quantities of cyanide tailings are regarded as waste and stored, resulting in significant wastage of land resources. Moreover, residual beneficiation reagents, cyanide ions, and heavy metal ions in cyanide tailings cause severe pollution of water and land (Laitos et al., 2013; Donato et al., 2007; Mudder and Botz, 2004). In addition, cyanide tailings often contain valuable elements such as gold, silver, copper, lead, zinc, sulfur, and iron, which, if not recycled, would result in considerable wastage of resources. Hence, it is imperative to study the reduction and safety of cyanide tailings, and the mineral resources present in them."

Jan 1, 2018

By C. G. Anderson

Industrially proven and applied nitrogen species catalyzed (i.e. NSC) acidic pressure leaching has been utilized to treat a number of ores, concentrates and recycled materials. This versatile technology offers many advantages including low temperatures, low pressures, low capital costs, low operating costs, faster throughput and less costly materials of construction than conventional pressure oxidation. This paper will elucidate the application of this technology for production of gold, silver, palladium, rhodium, zinc, germanium, gallium, cobalt, copper, molybdenum, rhenium and nickel. Recycled material applications will also be elucidated. In addition, details of an application for treatment of a refractory chalcopyrite copper and gold bearing ore will be presented and pertinent economics discussed.

Jan 1, 2014

By Rob Morrison, Andrew Scott

"Long before a modern mine commences operations it has already become a wealth of information. After start up, it can generate enormous quantities of data - especially with semi-automated data acquisition by instrumented mine equipment.However, much of this data is of limited use for evaluation of (potential) performance unless it links in some way to the site business model.An underlying reason for this waste of data is that the different cultures, financial, technical, community, environmental, etc, not only have many areas of interest but also have very different conceptual models by which they evaluate performance.It is too ambitious to attempt to bring all of these cultures together - in a single step.However, the success of the Mine to Mill - project has demonstrated that substantial operational value can be added by using a more integrated approach to comminution. The next logical step is to integrate measurement and then to track performance from ore body model to saleable product and waste disposal. From resource to product also represents a path from very sparse, highly variable data to much more detailed measurement and more representative sampling.However, in both cases the data collected is strongly focused on the technical requirements - not on the business model.This paper considers how to define at least some of the key decision points in terms of some case studies.Performance data from many areas might be used to derive simple models which can then be used for forecasting and optimisation of planning."

Jan 1, 2003

By M. Brozek

The constant of flotation velocity is the value characterizing the kinetics of cyclic flotation. In the statistical theory of flotation its value is the function of probabilities of collision, adhesion and tearing off the grain from the air bubble. The grain ? air bubble collision plays a key role since there must be a prior collision before the grain ? air bubble adhesion happens. The probability of such an event to occur is proportional to the relation of the grain diameter to the bubble diameter. When the grain sizes are given, it is possible to control the value of collision probability by means of the size of air bubbles. Consequently, it is significant to find the effect of physical and physicochemical factors upon the diameter of air bubbles in the form of a mathematical dependence. In the pneumo-mechanical flotation machine the air bubbles are generated by the blades of the rotor. The dispergation rate is affected by, among others, the rotor rotational speed, the amount of air transported to the flotation chamber an time and the liquid surface tension, depending on the type and number of applied flotation reagents. In the proposed paper the authors will present the distribution of air bubble diameters on the grounds of the above factors, according to the laws of thermodynamics. The correctness of the de-rived dependences will be verified empirically.

Jan 1, 2014

By Yosep Han

Mechanically-induced chemical reactions between natural beach ilmenite (FeTiO3) and silicon (Si) have been examined by a combination of X-ray diffraction (XRD) and scanning electronic microscopy (SEM) analyses. The effect of various milling time on the phase transformation, crystallite size, and lattice strain of a beach sand ilmenite with silicon, and on their leaching behavior in hydrochloric acid (HCl) has been investigated. For mechanically activated FeTiO3, the crystallite size decreased and lattice strain increased monotonically with time of milling. However, the mechanochemically synthesized ilmenite with silicon showed a relatively smaller crystallite size and greater lattice strain compared with the mechanically activated ilmenite under the same milling condition. In accordance with the elapse of milling time, the intensity of both pure FeTiO3 and mechanically activated FeTiO3 gradually decreased. However, in case of the mechanochemically synthesized ilmenitereduction of FeTiO3 by silicon resulted in formation of rutile TiO2 at the milling time of 20 h and afterwards. Additional leaching experiments were carried out at an HCl/ilmenite (wt%) ratio of 20:1. The concentration of HCl was 3 M and the reaction temperature ranged from 70 to 90 oC. Mechanical activation was observed to significantly enhance the dissolution rates of both iron (Fe) and titanium (Ti) in HCl. Particularly, effects of both milling time and silicon addition on the dissolution rates of titanium and iron were significant, while those of temperature were relatively minor under the conditions investigated in this study. Keywords: mechanochemical treatment, natural beach ilmenite, silicon, leaching behavior

Sep 1, 2012

By H. B. Zhou

The process of bioleaching marmatite using moderately thermophilic bacteria has been studied in this research by comparing marmatite leaching performance of mesophilic bacteria and moderately thermophilic bacteria and valuating the effect of venting capacity on marmatite leaching performance of moderately thermophilic bacteria and the effect of pulp densities on marmatite leaching performance of moderately thermophilic bacteria. The results show that moderately thermophilic bacteria have more advantages over mesophilic bacteria in bioleaching marmatite. Aeration agitation can improve the transfer of O2 and CO2 in solution and promote the growth of bacteria and therefore, enhance the leaching efficiency. With the increase of pulp density, the total leaching amount of valuable metals increased, however, the extraction efficiency decreased due to many rea-sons, like increasing shear force that results in poorly growth condition for bacteria, etc.

Jan 1, 2014

By Bent Babel, Martin Rudolph

"The characterization of reagent-mineral interactions in flotation systems of finely intergrown ores holds difficult challenges for the applicability of standard techniques like Hallimond tube tests and contact angle experiments or renders them impossible due to a lack of sufficient samples in terms of quality and quantity. This disadvantage may not apply to more sophisticated techniques, but these often do not work in an aqueous environment. We present the utilization of an atomic force microscope with a hydrophobic colloidal probe to characterize the wettabilities of individual mineral domains of an ore sample, while additional spectral information is gathered by Raman spectroscopy. The exemplary ore sample investigated is mainly containing cassiterite and quartz, therefore the reference measurements like Hallimond tube tests and contact angle experiments were carried out with this binary system as a comparison. The focus of the study lies in the correlation of data gathered by the atomic force microscope and the Raman spectrometer with data from standard techniques. Finally, the applicability of the colloidal probe atomic force microcopy technique for reagent-mineral investigations is critically evaluated.INTRODUCTIONThe focus of this paper is the application of colloidal probe atomic force microscopy (CP-AFM) for theinvestigation of reagent-mineral interactions on a binary system of cassiterite and quartz. This and similar concepts using hydrophobic AFM probes have been applied by multiple authors (Rudolph and Peuker, 2014a; Rudolph and Peuker, 2014b; Wada et al., 2017; Xie et al., 2017). The hydrophobic interaction is the main interacting mechanism for the hydrophobic colloidal probe with hydrophobic sample surfaces and the long range attractive component has been accounted to nanobubbles on the interacting surfaces (Yakubov et al., 2000). More detailed information on nanobubbles are available in two reviews compiled by Attard and Hampton (Attard, 2003; Hampton and Nguyen, 2010). This paper is based on the work by Rudolph and Peuker comparing different AFM based measuring concepts, additionally gathering data with Raman spectroscopy and correlating results of microflotation and CPAFM measurements (Rudolph and Peuker, 2014a; Rudolph and Peuker, 2014b)."

Jan 1, 2018

By Leopoldo Gutierrez, Esau Arinaitwe, Marek Pawlik

"The effect of various polymers, including: anionic carboxymethyl cellulose (CMC), polystyrene sulfonate (PSS), humic acids (HA) and non-ionic hydroxypropyl cellulose, on the wettability of Athabasca bitumen was evaluated through dynamic contact angle measurements using the captive bubble technique. The tests were carried out as a function of pH at a constant ionic strength (0.01 mol/L sodium chloride). The evolution of the three-phase contact angle between the solution, bitumen and an air bubble was followed as a function of time over a period of ~6 minutes. The contact angle data were modelled using a first-order kinetic equation. The results were analyzed in terms of the initial contact angle, the evolution rate constant, and the steady-state contact angle value. In the case of anionic polymers, a pronounced decrease in the initial contact angle value was observed at pH 3. Under acidic conditions, there was no significant effect of CMC observed on the steady-state contact angle value but PSS and HA significantly decreased the steady-state contact angle value. At pH 8.5. the anionic polymers did not affect the wettability of the bitumen surface but they significantly decreased the contact angle evolution rate. These results suggested that CMC is not capable of permanently lowering the hydrophobicity of bitumen, and the polymer only slowed down the evolution of the contact angle to the steady-state value. The results also showed that polystyrene sulfonate and humic acids were capable of making bitumen hydrophilic but only under acidic conditions. Only hydroxypropyl cellulose (HPC) produced a large decrease in the steady-state contact angle under alkaline conditions (pH 8.5). The kinetics of contact angle evolution in the presence of HPC was also drastically lowered. The results were discussed in terms of the chemical composition of the polymers and their different affinities towards the bitumen surface."

Jan 1, 2014

By W. Kobal

The extraction of nickel (Ni) and cobalt (Co) from the laterite deposit of Ramu nickel-cobalt Project in Papua New Guinea was performed in this study. Chemical analysis by Inductively Coupled Plasma (ICP-AES) atomic emission spectrometer, SPS-3000 (Seiko Instruments (Inc.), shows the ore contains 48% Fe, 1% Ni, 0.1% Co, 1.8% Al, 0.14% Mg, and 0.8% Mn. Characterization by X-ray diffraction (XRD) analysis of the laterite ore obtained from the mine site shows the ore contains 70 to 80% goethite (FeOOH), assuming Fe content of 48% is mainly from geothite. The main leaching parameters investigated include; slurry temperature, leaching time and sulphuric acid (H2SO4) concentration to evaluate nickel and cobalt extraction. For all experiments, 10g batch samples are put into 300 ml beaker containing 100 ml of sulphuric acid of varying concentrations (1M, 2M, 4M). During the leaching period, 5 ml slurry samples are withdrawn at different times and filtered to obtain filtrate for ICP analysis to monitor nickel and cobalt extraction. Solid samples at the end of all tests are also obtained by filtration and after drying, XRD and ICP tests are performed to monitor nickel and cobalt contents. According to the test results performed at normal atmospheric pressure, over 99% of nickel and over 50% cobalt were extracted into solution within 120 min at 95ºC in 2M H2SO4 solution. Similar results were obtained when only temperature was reduced to 90ºC, but cobalt extraction increased to over 70% when leaching time was increased to 240 min. Further reduction in temperature to 80 and 60ºC resulted in reduction of nickel and cobalt extraction. At the end of each leaching test, magnetite was seen to attach to magnetic stirrer. The study showed nickel can be completely leached into solution but cobalt only up to 70%. Keywords: atmospheric pressure, sulphuric acid leaching, nickel laterite

Sep 1, 2012

By József Faitli, Barnabás Csoke, Károly Solymár, Zoltán Hatvani, Dimitri Papanastassiou

"Grinding has a significant economic impact on ore dressing/processing, therefore the sizing of mills has an outstanding role.In most cases, the sizing of dry or wet mills for ore processing is primarily based on the determination of the Bond grindability index, using the Bond-Kjos-Rowland relations. In several cases, grinding takes place under conditions different from these and the grinding conditions have a great influence on the post-grinding process. This is particularly true for the grinding of bauxites where grinding takes place in alkali, often in higher temperature (up to 100 ºC) in alkali Liquor. So it is necessary to develop a testing method providing a reliable grindability index even under these special circumstances (grinding in alkalis medium at different temperatures) and allowing a more precise mill sizing. The new heated mill is suitable to determine the grindability index under temperature-controlled circumstances, in liquids with different temperatures (water, alkali). This paper presents in detail the equipment, the conditions (parameters) of the testing process for wet and alkaline grinding, the measuring results and the conclusions."

Jan 1, 2003

By Arkady Senchenko, Yevgeny Zhagun, Yury Kulikov, John Starkey

"The paper contains description of a new project in Russia - gold-processing plant at Aleksandrovskoye deposit (start up in September, 2013). The paper includes a brief description of plant flowsheet, data for material composition and technological properties of ore, as well as information about the achieved parameters of ore processing over the first months of plant operation. The project is interesting because a new semiautogenous mill and a ball mill were purchased on the basis of SAGDesign Consulting Group recommendations after the testing of ore samples characterizing the deposit according to specific years of operation. The plant has relatively small design capacity - 750 000 tpa, but nevertheless is the biggest gold-processing plant in the territory of Zabaikalsky region. Major valuable component in the ore is gold, silver is recovered as a by-product. The ores are very hard to grind. The design grinding flowsheet includes a semiautogenous mill operating in closed circuit with a screen, and a ball mill operating in a closed circuit with hydrocyclones (SAB). Process technology includes gravity processing and flotation with subsequent cyanide leaching of concentrates. Mill operation analysis and conclusions about the compliance of the achieved values to target ones are shown, as well as the accuracy of SAGDesign method when applied to very hard ores of Aleksandrovkoye deposit are presented in this paper. Basic directions of technological flowsheet optimization are also given."

Jan 1, 2014