Search Documents

By Ventsislav Stoilov, Angel Angelov, Ivan Korolev, Antti Remes, Todor Pukov, Stoyan Gaydardzhiev

"The process modeling and simulation studies aim for better process operation and favorable environmental impact. The objective of this work is to set up a simulation model of the Assarel copper flotation circuit for planning and optimization of the process with the aim of increased metal recovery. The model is parameterized based on laboratory flotation tests of ore samples from the Assarel mine together with mineralogical studies by X-ray diffraction (XRD) and Mineral Liberation Analysis (MLA). A combination of several techniques allows reliable identification of mineralogical composition of the selected samples. The changes in the proportion between sulfide minerals in various products along the circuit have been also documented. Further, this information is used in the simulation model and in data reconciliation procedures for establishing mass balance. The simulation accuracy is studied by comparing the simulations with the plant survey based mass balance. Constructed simulation model can be used to run alternative process scenarios. As an example, the flotation circuit performance with different reagent regimes is simulated based on data from batch flotation tests. Two reagents were considered for this purpose, dithiocarbamate-based one and xanthogen formate/mercaptan blend. It has been revealed that these reagents do not have the same influence on the selective flotation. The one improves flotation of gold and overall recovery but without notable selective action. In contrast, the other showed better selectivity towards copper, rejecting more gangue and lowering gold recovery. The model is also applicable for process optimization studies with different feed compositions, flowrates and circuit configurations. INTRODUCTION In the pursuit for elevated technological indicators, finding an optimal set of process parameters fully utilizing the potential of the equipment is a key factor to success. Over the past decades, there has been a substantial development in flotation circuit optimization through performance benchmarking using metallurgical modelling and steady-state computer simulation. Practical simulation engineering tools are based on experimental data obtained from laboratory tests and from plant surveys and operation data. With the help of flotation models, it is possible to study grade-recovery response with different feed compositions and throughputs, and with various cell-operating parameters, as well as to evaluate and design different flowsheet configurations. Outotec’s HSC Chemistry® software, which incorporates simulation and mass balancing modules alongside with several other tools, can assist with this optimization (Mattsson et al., 2015)."

Jan 1, 2018

By Ranjeet K. Singh

Kelsey Centrifugal Jig was found to be promising for the beneficiation of fine coal particles. The present study was aimed at in-depth understanding of the separation features of Kelsey Jig through detailed experimentation. Beneficiation of fine coal of size 150 x 300 µm was studied in a laboratory Kelsey Jig. The thickness of the ragging bed is found to be an extremely crucial parameter apart from the other process parameters such as rotational speed and pulsation frequency. A constant pulp density (25% solids) of the feed slurry was maintained in the study. The feed rate was also kept constant at 50 kg/hr dry solids. Silica sand of size -1.68+0.85 mm was used as ragging material to avoid the pegging of internal screen having an opening of 425 µm. The rotational speed was found to have significant effect on the depth of the ragging bed and its porosity, which influenced the separation performance considerably. Pulsation was identified as the key factor in stratifying the coal bed and defining the misplacement as well as ragging bed porosity, which influenced the mass yield and quality of the products. Beneficiation studies were carried out with rotational speed varying between 900-1000 rpm while pulsation frequency was kept within 850-925 rpm. In a single pass through the Kelsey Jig 7-8% (absolute) reduction in the ash content of the feed material was observed at more than 55% mass yield. High rotational speed, moderate pulsation, and low ragging bed depth favored good cleaning. A high bed depth was found to facilitate rejection of high ash materials. It was established that Kelsey Jig is effective in fine coal cleaning though a controlled operation is required in order to achieve superior performance. Keywords: enhanced gravity separator, g-force, separation performance, ragging material, coal beneficiation

Sep 1, 2012

By Trevor Saldanha, Stephen Grano

A key uncertainty in flotation modelling is determining, a priori, the proportion of each mineral which will develop a certain rate constant for different feeds of variable liberation and hydrophobicity. First and foremost is the ability to predict the proportion of minerals that will not be recovered, even at very long flotation times, and which therefore report to the tailing stream as the non-floatable fraction (i.e., having a zero rate constant). Recent empirical evidence has shown there are at least two factors which contribute to heterogeneity in flotation rates and, in particular, the appearance of a non-floatable fraction - heterogeneity in the distribution of adsorbed collector amount on a particle-by-particle basis, even for the same liberated mineral in the same size fraction, and the existence of a critical contact angle below which the bubble-particle union is unstable. In this paper, inferred measures of the critical contact angle for liberated particles are compared with stability model calculations. This has demonstrated that the dependency of the critical contact angle with particle size and mineral specific gravity are explicable by bubble-particle stability considerations. This argument is further extended to the flotation behaviour of composite particles, as a function of liberation class, in which the wetting perimeter of the attached bubble on the composite particle surface is constrained by the presence of a surrounding hydrophilic domain for the case of simple binary composites. Reasons for the different flotation behaviour of composite particles having different textures, as noted in the literature, are also discussed in terms of the stability of the bubble-particle union.

Jan 1, 2014

By S. Banisi, O. Farshid, M. R. Rozebehi, A. Bahar, A. Arghavani, M. Mahdavi

At the rougher flotation circuit of the Miduk copper concentration plant (Kerman, Iran) five column cells (CISA) with the diameter of 4m and height of 12m using static mixer type (MicrocelTM) spargers have been installed. Based on the initial design, columns should accept a feed rate of 625 t/h with 80% passing size of 90 µm and solids concentration of 28% and produce 88% of the plant concentrate (i.e., 22 t/h) containing 32% copper. Due to mechanical and processing problems this objective was never realized and theses columns were remained out of operation from the commissioning time (2005). A new attempt with the aim of returning these cells into operation started in 2013. The results of an extensive study indicated that spargers plugging due to the entrance of small amount (2 kg) of coarse particles (up to 2.5 cm) because of usual problems at the plant environment was the main reason of columns non functionality. With a change in the recycle pump inlet design to the column, which prevented the entrance of coarse particles to the spargers, the operation of the column significantly improved. It was found that in order to have a stable operation of the columns at the rougher stage the feed rate for each column should be reduced from 125 (design) to 70 t/h. The air superficial rate had to be also reduced from 1.9 (design) to 0.6 cm/s. A period of 10 days of continuous operation showed that the carrying capacity was 0.23 (g/min/cm2) which was significantly lower that of the design value (i.e., 0.58). The gas hold up was found to be lower than 10% beyond which columns started to move to the turbulent state indicated by "boiling" froth. The average life time of spargers was determined to be 20 days which considered to be very short. The average recovery and concentrate grade of these columns were found to be 68% and 32%, respectively. The high wear rates of spargers, unusually high level of maintenance and supervision needed and instability of the operation made the plant managers not to use column cells as the roughers.

Jan 1, 2014

By Paulo Sérgio de Oliveira, Joaquim D. Donda, Andreia C. Rosa

"The search for energy efficient technologies for comminution processes is constant in mineral processing studies, since those processes represent a major percentage of operational costs. In this context the use of stirred mills is increasing, especially for ultrafine grinding. Although many authors claim that these new equipment are more efficient than the conventional ball mills, there were very little chances to prove that in a practical way, since there are few industrial circuits where those technologies perform the same duty. Therefore, the regrinding circuit of Germano second concentrator offers an interesting opportunity: a vertical mill operating in parallel with two ball mills. During almost two years of operation, several sampling campaigns were conducted to evaluate the vertical mill performance and to compare the operational data of the three mills. The industrial data was also compared to jar mill tests results, which are monthly conducted in Samarco labs in order to predict the specific energy consumption required by the ore fed to these circuits. The vertical mill demonstrated the same ability to achieve the product specifications of the ball mills while proved to be able to reduce the medium specific energy consumption in about 40%."

Jan 1, 2014

By Chris A. Fleming

"The ability to recover cyanide from gold plant tailings has been known almost as long as the cyanidation process has been practiced, but there has been little incentive to process tailings in this way in the past. With the development of technologies that make it possible to recover and recycle free or complexed cyanide directly from gold plant slurry tailings, which indicates, on paper at least, significant cost savings compared to cyanide destruction, coupled with the introduction of legislation to seriously limit the discharge of cyanide to the environment in most gold-producing regions of the world, many companies are evaluating the cyanide-recovery alternative.There is arguably an even more compelling reason for mining companies to consider cyanide recycling. With the growing storm of negative public opinion that the use of cyanide in the mining industry is attracting - following several highly publicized spills over the last couple of years - the time has come for the gold industry to demonstrate environmental diligence and stewardship in the use of this commodity that is so vital for their industry. There is no doubt that the widespread implementation of cyanide recycling will reduce the impact of the cyanidation process on the environment, both by reducing the risk of spills (with less cyanide being transported from manufacturing plants to gold mines), and by reducing the loading of toxic and nontoxic metals and ions in the tailings.This paper briefly discusses the pros and cons of the different processes that are available for the treatment of gold plant tailings to regenerate and recovery cyanide for recycling, and presents a techno-economic argument for the incorporation of this technology into many gold plant flowsheets today."

Jan 1, 2003

By S. S. Yu

In this paper, the producing process of using V2O3 as raw material to obtain vanadium nitride was analyzed through the means of thermodynamic. The analysis shows that conversion follows the principle of reduction step by step in the conversion process of V2O3. The temperature of the reaction system has prominent influence on the nitrogen content of products, and the reaction is very sensitive to temperature. As raising temperature, the fine grain structure of the nitrides is more evident, and the grain size of nitrides increases. At 1703K, the nitrogen content of the products tended to be constant after soaking over 3 hours.

Jan 1, 2014

By G. X. Du

Reaction kinetics of serpentine and hydrochloric acid is theoretical basis for optimizing reaction process conditions of serpentine and hydrochloric acid. Kinetics of serpentine and hydrochloric acid was studied in this paper. The results indicated that apparent reaction order to hydrochloric acid was two and reaction kinetic equation could be expressed as: 2HClHCl,ddtckct-=·. The diffusion rates of hydrogen ions in liquid film on surface of serpentine particle and in amorphous silica layer generated in the reaction and chemical reaction velocity during the reaction had important effects on to-tal reaction velocity. And chemical reaction velocity had the most significant influence. The relation of conversion rate of magnesia xMgO with reaction time could be expressed as: 1(1)xkt--=·.

Jan 1, 2014

By P. A. Harvey

Previous studies have reported that inorganic electrolytes can enhance floatability of coal. The research has shown that the enhancement, if any, is highly dependent on changes in solution pH, type of electrolyte, and electrolyte concentration. The reasons for this are still not clear. In this study the floatability of coal particles in mono and divalent salt solutions was investigated. The zeta potential and hydrophobicity of the coal was measured experimentally, and a modified Hallimond tube was used to determine the floatability of coal particles by single bubbles, where the collision efficiency was equal to unity. The experimental information was used in conjunction with the Hogg-Healy-Fuerstenau equation to quantify the electrical double layer interaction. It was found that for low electrolyte concentration (less than 0.1 M) solutions the flotation recovery of coal particles was less than that for distilled water, and decreased with increase in concentration. Conversely, at electrolyte concentrations above 0.1 M, flotation recovery increased with increasing concentration (Figure 1). Both of these results are consistent with previous observations, but are inconsistent with expectations when considering the possible influence of electrical double layer interaction. Modelling of the system indicates that the electrical double layer is compressed with increasing electrolyte concentration, resulting in an increase in flotation recovery due to a diminishing of the (electrical double layer) repulsion between the bubble and the coal particles. Moreover, for electrolyte concentrations above about 0.1 M the electrical double layer is completely depressed and would have little further influence, if any, on the flotation process. Therefore, the electrical double layer interaction is not the principal determining factor for the flotation of coal in electrolyte solutions.

Jan 1, 2003

By Aidan Giblett, Karen McCaffery, Robert Dunne

"A worldwide decline in competency levels of practicing metallurgists over recent decades has become clearly evident and is a common topic of discussion among senior practitioners and professional associations. The associated impacts on the industry are material and include operational inefficiencies, missed optimisation opportunities and suboptimal new plant designs. There are many contributing factors to this condition. Decrease in competency is particularly evident both in regions where imbalance between supply and demand has led to a general reduction in experience levels for comparable roles over time and in emerging regions where a rapid rise in demand for practitioners has occurred in conjunction with rapid economic development and industrialization. The context, depth and breadth of education curricula and levels vary with location such that solutions to the technical competency dilemma may need to be developed specifically for each region with these influences in mind. Delivering, demonstrating and maintaining competencies are a critical requirement of undergraduate training and ongoing professional development. Other factors such as generational and cultural characteristics and expectations, political influences, role requirements and employment reward and recognition systems all play a critical role in determining if core competencies can be effectively developed, applied and subsequently maintained. This paper reviews factors impacting and some common approaches to competency development. The authors’ experiences in the management of professional development efforts within the global industry are reviewed and a blueprint proposed to address industry requirements in this area."

Jan 1, 2014

By M. A. Hampton

The surface oxidation of sulfide minerals in aqueous solutions is an important sub-process in sulfide flotation and hydrometallurgy, but a full understanding of the oxidation process and products is still lacking. Many oxidation pathways and products involving elemental sulfur, metal polysulfide, metal-deficient sulfide and sulfate have been proposed, confirmed and argued. In this paper we provide further insight into the surface electrochemical behaviour of galena in aqueous solutions. For this research we have developed a novel experimental system, that combines chronoamperometry and AC-mode AFM surface imaging, which allows for in-situ, synchronized electrochemical control and examination of oxidative surface morphology. At pH4, the morphology of elemental sulfur (detected by ex-situ Cryo-XPS) formed on the oxidizing galena surface depends on the electrochemical potential pathway. In multi-step chronoamperometry (i.e. four potential steps from 0 mV to + 350 mV) the sulfur forms as nanoscopic domains, whereas in single-step chronoamperometry (i.e. one potential step from 0 mV to + 350 mV) sulfur forms as a heterogeneous layer. In each case the oxidation is controlled so that the number of electrons (coulombs) passed per unit area is the same, therefore the amount of sulfur produced is also the same. The differences in morphology with electrochemical potential pathway are explained using a nucleation and growth model. The formation of sulfur on the surface increased both advancing and receding contact angle of galena, but the morphological changes induced by different electrochemical potential pathways did not significantly alter the hydrophobicity of the surface. Keywords: galena, lead sulfide, oxidation, Atomic Force Microscopy, electrochemistry, collectorless flotation, hydrophobic

Sep 1, 2012

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, M. Zare

High Pressure Grinding Roll (HPGR) plays a major role in increasing specific surface area of iron ore concentrate for producing pellet feed. HPGR grinding mechanism implies that material be compressed between the two rolls, therefore layer of material must be able to resist required pressure for achieving suitable grinding conditions. In this study for determining a simple relationship between material pressure resistance ability and HPGR main design parameters, piston press tests were performed on different iron ore concentrate samples along with HPGR Blaine increasing tests. Piston press tests results showed that by decreasing moisture content, material pressure resistance increased and in constant moisture content this parameter will change based on material specifications. HPGR Blaine increasing tests results showed that by decreasing moisture content, HPGR specific throughput and working gap increased and in constant moisture content this parameter will change based on material specifications. For all of the studied samples at worst condition, we got the results including: HPGR delta gap equal to zero, specific throughput lower than 200 ts/hm3.According to the tests results, HPGR Applicability Index (HAI) can be introduced at four different class types from 1 (weak) to 4 (excellent). This index determines achievable specific throughput and possibility of using HPGR according to material specifications, i.e. for HAI 1-4 the pressure resistance is <90, 90 to<125, 125 to <150 and = 150 bar, respectively. Similarly for HAI 1-4 specific throughput is <200, =200, =220 and =250, respectively. So based on design moisture content, if concentrate HAI is 3 or 4, HPGR is a correct choice. For HAI 2, HPGR can also be used. But for a material with HAI equal to 1, HPGR is not a good solution. As a result in order to apply HPGR for HAI 1, material condition such as moisture or slime content should be decreased.

Jan 1, 2018

By C. Stollberg

The recovery of valuable materials from electronic waste is of growing importance for the re-source management not only in the industrialized nations. Being a significant step in an innovative automated process for recycling of metals and plastics from used electric and electronic equipment, the results of the work introduced below, prove the applicability of microbial leaching of metals from printed circuit boards (PCBs) at industrial scale. Within the first project step, which started in March 2005, experiments in shaking flasks with a mixed culture of chemolitotrophic bacteria (mainly Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans) were carried out to study the solubilization of non-ferrous metals present in the electronic waste. It was found that the best results were achieved by means of a two-stage process in which leaching of these metals was carried out by acidified ferric sulphate solutions generated as a result of the prior bacterial oxidation of ferrous ions to the ferric state. Special reactor systems for bacterial generation of such solutions and for the subsequent leaching of non-ferrous metals from the waste were developed, constructed and tested under laboratory and pilot scale conditions. The optimum technological parameters such as concentration of iron ions, pH-value, temperature and presence of nutrients were established for both reactor systems. Parameters such as particle size, pulp density and flow rate of the suspensions being leached were established for the leaching process carried out under continuous-flow conditions. The complex flow sheet reflects a highly efficient technology on the basis of metal recovery, environmental effect and economical acceptance. The process was successfully implemented into an industrial demonstration unit.

Jan 1, 2014

By Jun Qiu, Ping Chen, Xianjun Lu

Nitrogen of different forms from wastewater was adsorbed by the natural bentonite and modified bentonite. The effects of adsorption conditions on the nitrogen removal were investigated. The experiment results showed that natural bentonite could easily adsorb ammonia while poorly adsorb nitrate, the organic bentonite modified by octadecyl trimethyl ammonium could effectively adsorb nitrate with the removal ratio increased from no more than 5% to 89%. Two kinds of bentonite were added together to the simulated wastewater which contained ammonia nitrogen of 15mg/L and nitrate nitrogen of 10mg/L, the dosages were 1.0g respectively. Both ammonia and nitrate had significantly decreased on conditions that the oscillation time was 1.0h and room temperature 20?. The optimum pH value for ammonia removal was 7 while for nitrate removal was above 7. The adsorption isotherm fitting results indicated that the Freundlich adsorption isotherm was the better model to describe ammonia adsorbed on the natural bentonite and the saturated adsorption capacity was 10.25mg/L, while the Langmuir isotherm could better describe the adsorption of nitrate on the organic bentonite and the saturated adsorption capacity was 14.35mg/L. Fully considering the interaction between different ions and controlling the appropriate conditions, removing nitrogen from wastewater by adsorption of bentonite is an economic and effective method.

Jan 1, 2014

By S. Z. Khan, Veerendra Singh, Y. Rama Murthy, S. Prasad, Sunil Kumar Tripathy, Gajanan Kapure

"In this study, a low-grade ferruginous low-grade chromite ore was subjected to reduction roasting by using conventional heating as well as microwave heating. Sukinda chromite ore deposit contains majorly iron-bearing minerals as gangue phase. The magnetic susceptibility of these minerals enhances effectively after reduction roasting. Alteration of crystalline structure and magnetic property of these metals enables separation of low-grade ore by using magnetic separation. Conventional roasting studies by varying the temperature, time of reduction and reductant dosage were changed for low-grade ferruginous chromite ore. Similarly, microwave power, retention/exposure time and reductant dosage varied for reduction roasting studies under microwave environment. It is found that low-grade ferruginous chromite ore can be upgraded by reduction roasting and 61.2% Cr2O3 was recovered with a chromium-to-iron ratio of 1.93 from feed chromium-to-iron ratio of 1. Microwave reduction roasting studies resulted in upgradation of chromium-to-iron ratio to 1.73 with a recovery of 21% Cr2O3.INTRODUCTION The chromite ore occurs as a spinel containing oxides of chromium, iron, magnesium and aluminium. Most of the Indian chromite deposits are of ferruginous (rich in iron content) which indicates the abundance of ferruginous gangue minerals along with chromite. The primary use of chromite ore is towards the production of ferrochrome alloys. Chromite ores with less than 40% Cr2O3 and the chromium-to-iron ratio (Cr-to-Fe ratio) <1.8 is considered to be unsuitable for the smelting process (Tripathy et al. 2012, Tripathy et al. 2012a). A considerable amount of low-grade chromite ore and overburden excavated during chromite mining is getting accumulated every year, causing a threat to the environment. Its disposal poses a significant challenge and, hence, the beneficiation of low-grade chromite ore and its utilisation has been attracting a lot of attention. Different physical method of beneficiation methods is generally employed for the improvement of the Cr-to-Fe ratio (Tripathy et al. 2012, Murthy et al. 2011, Tripathy et al. 2012a, Tripathy et al. 2013, Tripathy et al. 2016, Tripathy et al. 2017, Tripathy et al. 2017a). It is observed that the enrichment of the chromite ore is carried out by using gravity and in some places by magnetic separation. However, the enrichment of Cr-to-Fe ratio from low-grade ferruginous chromite ore is difficult by using the above-mentioned beneficiation methods due to the presence of near gravity and near-magnetic susceptibility minerals along with chromite. However, an alternative beneficiation method is needed to explore for the beneficiation of such mineral deposits. Reduction roasting followed by magnetic separation is an alternative option for the separation of these types of ores which is widely reported for the iron and manganese ore (Li, et al., 2010; Chun, et al., 2014, Rath et al., 2018). These processes are majorly focussed on differentiating the magnetic susceptibility between minerals and subsequent separation by using magnetic field. The main advantage of such method is dry process option along with the pre-processed product for the costly smelting process. Also, the roasting of minerals in a microwave environment is also an active research topic in the recent time. So, the amenability of the separation feature of the roasting process by using conventional heating as well as microwave heating can be can be studied for the low grade ferruginous chromite ores."

Jan 1, 2018

By S. V. Bogdanov, S. I. Grishaev

"The article presents the materials about the appropriateness of the use of rental indices to assess the effectiveness of the use of deposits of rare earth elements (REE). The authors suggest from the standpoint of rent payments to rate for the owner the possibility of using the anticipated rental income as the indicator for the analysis of preferences and economic significance of enrichment of extracted raw materials in the emerging field of rare earth metals (REE). Usually from ore mined at the fields, for flotation technology to produce concentrates with collective REE, then they are subjected to chemical-metallurgical processing of the received products are divided into pure oxides, chemical compounds or isolated from them pure metals and alloys. This commercial product is shipped to the buyer. REE were a non-renewable natural resources, so the calculations for determining differential and specific rent showed that during the development of the technologies of mineral processing of a specific field it is necessary to consider what the expected rental income depends on the magnitude of differential rent is related to the volume of production of REE for the whole planned period of exploitation of natural resources. This income is determined by the amount of stock field. For long-term exploitation of the deposit is observed in almost direct proportional dependence between the annual differential rent and the rental income. The decrease in rents in the long run is determined by the change in the composition of ores included in the extracted raw materials and the balance between light and heavy REE. The largest 70% reduction of the rent projected for ""cerium"" fields, while for ""yttrium"" these losses are considerably smaller. Tomtor, Chuktukon and Katuginskoye Russian deposits are characterized by a level of rent that is comparable to the mastered foreign sources of REE. Thus, the enrichment of minerals with REM in the domestic deposits is quite competitive at the world level. INTRODUCTION Deposits of rare earth metals (REE) are non-renewable resources that should be developed and used so that it would be possible to provide a reduction due to payment of appropriate resources for future generations. This compensation, due to the reduction of natural resources, can be carried out both in natural and in economic terms (1). When analyzing economic compensation options, particular attention should be paid to rental income in assessing the attractiveness of using different REE deposits. It is known that absolute and differential rents are summands when calculating the value of natural rents. The value of the absolute natural rent is proportional to the unit price of the product obtained from mineral raw materials and sold on the commodity market. Limitations, as well as the use in production processes and business, contribute to the gradual reduction of natural resources, which increases their consumer value and affects the price of commodity products from primary raw materials."

Jan 1, 2018

The ever increasing demand for energy and the progressive depletion of crude oil resources, have renewed interest in oil shale as an alternative fuel resource. Weathered oil shale samples were assembled from El-Nakheil phosphate mine in Quseir area, Eastern desert, Egypt. The oil shale samples were prepared and analyzed by XRD (X-ray diffraction), XRF (X-ray fluorescence spectrometry), and optical microscopic techniques. Rock-Eval pyrolysis and total organic carbon were used to study shale hydrocarbon potential. A leaching procedure using inorganic and organic acids was used to selectively dissolve the oil shale associated ash forming minerals. XRD results showed that calcite is the dominant carbonate mineral, whereas primary silicate minerals are quartz and montmorillonite. SEM (Scanning Electron Microscopy) observations indicated that the organic matter is dispersed throughout the rock matrix. The acid soluble fraction upon leaching was determined to be 37.59 and 42.74 wt% by using 5% HCl and 10% HCl, respectively. The TOC was increased from 20.78 to 29.88 and 34.09 wt% by using 5% HCl and 10% HCl, respectively. Keywords: el nakheil oil shale, characterization, xrd, xrf, sem, elemental analysis, proximate analysis, ultimate analysis, thin section, rock eval pyrolysis, acid leaching

Sep 1, 2012

By Eduard Stefanescu, James M. Mwase, Egon Sehner, Stoyan Gaydardzhiev

"The study is focused on investigating the production of synthetic rutile of 95% purity or higher from a Norwegian ilmenite ore concentrate. This was to be achieved using a sequential process involving oxidative-reductive roasting at 975°C, followed by magnetic separation to further concentrate the sample and finally leaching with 20% HCl to remove mostly Fe-based impurities leaving behind synthetic rutile. The key process parameters considered were roasting time (1 and 2 hrs), leaching temperature (100, 125 and 145°C), pulp density (15 and 25wt%) and leaching time (3 and 6 hrs). The option of directly leaching the concentrate without pre-treatment was also evaluated. Test work was conducted using samples screened to a size fraction of 105-212 µm. Samples were leached in a 1 L glass autoclave. The reactor was hermetically sealed and thus the resulting pressure was not controlled but was dependent on the process temperature. The product from leaching was calcined and analysed via XRD and SEM to determine the purity of the product. The magnetic separation step was found to be ineffective and discontinued early in the study. Thus far a product with 97% synthetic rutile purity as analysed by SEM has been produced by directly leaching the concentrate at a temperature of 145°C, pulp density of 25wt% and leaching time of 6 hrs.INTRODUCTION The study investigates the use of a process route comprising oxidative-reductive roasting, followed by magnetic separation and then hydrochloric acid leaching and calcination to produce synthetic rutile from ilmenite concentrate. The grade of synthetic rutile produced should be suitable for chlorination to produce pigment grade TiO2. Hence the proposed process should produce a product consisting of no less than 95% synthetic rutile. Additionally, the product should have no more than 1.5wt% combined content of CaO and MgO (Zhang et al., 2011) as they tend to form high-boiling-point chloride leading to the malfunctioning of fluidized bed chlorinator (Cardarelli, 2008). Finally the product should have no more than 2.1wt% of Fe2O3."

Jan 1, 2018

By B. McFadzean, J. Taguta

The enthalpy of immersion is the heat change arising from the replacement of the solid-gas interface with the solid-liquid interface when a solid surface is immersed in a liquid. Although immersion calorimetry has been established as a valuable and reliable means of determining solid surface properties such as wettability, it has seldom been applied in mineral processing research. In this study, precision solution calorimetry was employed to measure the enthalpies of immersion of different minerals in water. The enthalpies of immersion were then related to the first-order flotation rate constant as determined by the microflotation technique. The same measurements were also made on sulphide minerals whose surfaces were modified to different degrees of hydrophobicity using different percentage coverages of amyl xanthate collector. The enthalpy of immersion technique was capable of distinguishing and ranking minerals according to their wettability. All mineral types and collector-treated minerals conformed to the same relationship that was found between the enthalpy of immersion and the flotation rate constant. This conformed, empirically, to a power law equation. As the enthalpy of immersion decreased, there were large increases in flotation response for very small changes in hydrophobicity. In addition, a critical enthalpy of immersion (CEI) was found, above which no flotation could occur. The scatter in the data points could be corrected for by adjusting the rate constant using the density of the minerals to produce a robust relationship between the rate constant and enthalpy of immersion. These results have shown that the enthalpy of immersion is able to indicate both the natural mineral hydrophobicity and the extent to which collectors can render a mineral hydrophobic. This technique has considerable potential to be used as a sensitive and accurate measure of mineral surface wettability in order to predict flotation performance.

Jan 1, 2018

Three high-grade limestone ores (CaO content over than 53 %) with different geological origin have been characterized for the synthesis of aragonite precipitated calcium carbonate. Limestone ores examined in this study showed different crystal particle size that cause difference in disintegration degree and surface area of the synthesized slaked limes. The limestone ore with smaller crystal particle size showed higher disintegration degree and also yielded slaked lime with smaller surface area, which is good for the synthesis of aragonite precipitated calcium carbonate. The synthesis of aragonite PCC using the limestone with a small crystal particle size was yielded needle-shaped aragonite with the aspect ratio of about 14. Keywords: limestone, lime, slaked lime, precipitated calcium carbonate, aragonite, accelerated carbonation

Sep 1, 2012