Search Documents

By Y. M. Zhu

Lead in environment often causes a serious health hazard. The removal of Pb2+ from aqueous phase is a beneficial project. In this paper, deposited Saccharomyces cerevisiae (S.c.) was chosen as adsorbent, Pb2+ ions as adsorbate, and the process of biosorption was studied. The dynamics of the adsorption was investigated. The adsorption mechanism of Pb2+ by S.c. cells was also investigated by detecting microstructure, zeta potential under different pH value, FT-IR spectra of the S.c. particles before and after biosorption. It was shown that the biosorption of Pb2+ by deposited S. c. is a rapid process, and the adsorbing equilibrium is reached within 10 minutes. The Zero point of zeta potential of S.c. cells is pH=3.3. When 2.0<pH<3.3, there exists biosorption (biosorption rate 76%~88%), which means static bio-sorption been not the only kind of biosorption. FT-IR spectrum analysis showed that groups on bacteria surface were mainly characteristic groups of protein and amylase; oxo-groups and nitric-groups on S.c. cell surface could chelate with heavy metal ions. Chemical adsorption might exist in the process.

Jan 1, 2014

By Ali Dehghani Ahmadabadi

Gravity separation technique is widely used in mineral beneficiation practices for its low cost, ease of operation, and eco-friendly nature. The most commonly used gravity methods for beneficiation of iron ores are shaking table, jig and spiral methods which aren&apos;t very effective for iron mineral fines. Multi-Gravity Separator (MGS) is suitable for the treatment of fines with a maximum particle size of approximately 500 µm. This study was performed on a low-grade haematite iron ore from Chadormalutailing dams. Detailed mineralogical, physical and chemical characteristics of a goethiticlateritic iron ore showed that the sample contained porous and friable oxides and hydroxides of iron. The ore sample had a feed grade of 35% Fe, 1.1% FeO, 15.5% SiO2 and 8.5% Al2O3. Haematite and goethite are the main iron-bearing minerals while quartzite and kaolinite are the major gangue mineral constituents. In this paper, the statistical evaluation and optimization of grade and recovery using a factorial design of experiment (DOE) method has been carried out for Chadormalulow grade ultra-fine haematite tailings with MGS. The input process parameters considered are drum speed, tilt angle, wash water flow rate and pulp density. The results show considerable improvements in both the quality characteristics such as grade and recovery with statistical evaluation and optimization, compared to the initial value of grade and recovery. Keywords: multi-gravity separator, mgs, statistical evaluation, optimization, haematite

Sep 1, 2012

By M. R. Hosseini

Among all gravity concentration methods, Shaking-table is the most effective one from the metallurgical point of view. In this study, Shaking-table was used for concentrating a manganese ore sample from Ghasem Abad area in Kerman, Iran. Experiments were designed by using L8Taguchi design with five variables and each variable in two levels. The influence of each variable and their interactions on the operation of the device was studied. The variables under investigation were: table slope, table frequency, water flowrate, feed rate, and particle size. The manganese concentrate grade and recovery were used as response variables. It was shown that water flowrate, table slope, feed rate, and particle size are the significant variable on concentrate grade; while, all the variables influence manganese recovery.

Jan 1, 2014

By V. A. Chanturiya

The results of development of new collecting reagents selectively interacting with the metals of platinum group (MPG) are presented. A new approach to the concentration of the platinum minerals from the fine grade platinum containing products with the use of cloud point polymers for the first time proposed for this purpose is discussed. An original method for the investigation of complexing reagents with the platinum under flotation conditions developed by authors is described. The influence of the complexing reagents on the xanthate adsorption and on the electrochemical properties of the platinum arsenide surface (sperrylite) as well with the interaction mechanism between the reagent and metallic platinum were investigated by means of the modern physical and physicochemical methods of the solid and fluid phase studies. The results of tests of some complexing reagents with the rich copper-nickel ore in the cycle of nickel-pyrrhotite flotation are given. The data obtained makes it possible to mark the complexing reagent containing phosphine group as the most effective additional collector for MPG. Cloud point polymers containing thioamide, aminosulphide, and phosphine functional groups were examined. It is shown that all the reagents tested increase the platinum and palladium extraction to the nickel-pyrrhotite concentrate without quality loss. Platinum containing particles flocculate selectively.

Jan 1, 2014

By S. Banisi

Thickening is the most widely applied dewatering technique in mineral processing. Thickeners are used to increase the concentration of suspension by sedimentation, accompanied by the formation of a clear liquid. As the particles get finer the thickening process encounters difficulty due to a significant change in the settling behaviour of particles. The batch settling tests of coal refuse of a coal washing plant which contained 91% particles smaller than 38µm and 0.6% coarser than 75 µm showed that the optimum feed percent solids that provided highest flux (solids handling capacity) was 4%. The flux of the pulp with the plant solids concentration (i.e., 10%) was 60% lower than that of the pulp with 4% solids. A thickener with a diameter of 22m based on the dilution of feed from solids concentration of 10% to 4% was designed. Monitoring of the thickener performance for a period of one month in the plant indicated that on average the feedrate of 25t/h (dry solids) with solids concentration of 10% could be thickened to the underflow concentration of 26.5% with a clear water overflow. It was found that the key component of the successful operation of the thickener is the dilution of the feed without which the overflow loses its clarity and the system ceases to operate under predetermined conditions. Specially designed feeding system which efficiently dissipated the energy of the incoming flow and staged flocculant addition regime are among the main contributing factors in making the design and operation of such thickener possible.

Jan 1, 2014

By M. Narasimha

The flow in a hydrocyclone classifier is highly turbulent complex nature of multi-phase structure, which has led designers to rely on empirical mathematical models for predicting the performance. A number of classifying cyclone models have been developed and successfully used in mineral comminution circuit simulators over the past four decades (Plitt, 1976 and Nageswararao, 1978). However, most of the mathematical models currently available to describe hydrocyclone classifier performance are based on single average mineral density component behavior. In industrial comminution circuits, the feed to the cyclone composed of a mixture of particles of varying degrees of liberation and sizes. The behavior of multi-component particles in a hydrocyclone is poorly understood and unaccounted for in most of the mathematical model equations available in the literature. There is evidence from a number of experimental data sets indicating the significant influence of the multi-component particles on measured cyclone performance. A concept for modeling the performance of hydrocyclones based on multi-component behavior is proposed in this paper. A set of semi-empirical model equations for cut-size, sharpness of separation are presented and the corresponding model parameters evaluated from the measured data are given.

Sep 1, 2012

By F. Q. Dong

According to the principle that should be originated from nature, compatible with nature, used in nature and back to nature and based on conception of designing of eco-material, the author combined the ideas of material, environment, zoology and healthy. Properties of natural mineral materials were used to produce micro-aggregate elements by bionic method, so its components and function could accord with living environment. Eco-mineral functional materials which can adjust, purify and optimize the microclimate were reviewed. The authors pointed out the multifunction, com-pounding, the compound characteristics and integration regularities of micro-aggregates. It was the first time in the world to put forward the ?gene? technique or ?material chip? technique of manufacturing function micro-aggregates and eco-function elementary materials. The results of this re-search supported by the national ?863? Hi-tech Project, mainly including the high-efficient air purifying mineral compound material indoor, the clay elementary antibacterial materials, the masonry cement/coating/putty/compound with preventing radon radiation, environmental friendly composite functional coatings, mosquito repellent and healthcare material and zeolite-based energy-saving composite materials, were introduced. Finally, the foreground of mineral materials in the field of future advanced eco-friendly materials was also discussed.

Jan 1, 2014

By Bertil I. Pålsson, Sture V. Persson, Kent T. Tano

"Grinding is one of the most energy consuming unit operations and is also a very inefficient and costly process. Therefore, it is of great importance to run the grinding process as efficiently as possible. The most common way today to control grinding processes is by measuring the power draw of the mill and try to keep it at a maximum level. However, some studies (Kawatra, 1989, Koivistoinen, 1989, Moys, 1989) have shown that this measurement doesn.t reflect everything that takes place inside a mill. Among other parameters like slurry rheology, temperature and charge behaviour, the volumetric filling of a grinding mill seems to have a large influence on the grinding efficiency (Herbst, 1988, Koivistoinen, 1992, Vermeulen, 1988). A problem in attempting to measure those parameters has been to get a sensor that is both robust and sensitive enough for continuous on-line measurement.This paper presents a method for the measurement of the apparent filling level in a pilot ball mill equipped with the Metso Continuous Charge Measurement system (CCM). In this technique a strain gauge sensor is mounted on a flat steel spring which is fitted into a recess underneath a lifter bar. In addition, a conductivity probe, the Boliden Grinding Measurement System (GMS), is mounted in another lifter bar with the purpose of comparing the two measurements. To visualise the behaviour of the charge a DEM modelling technique is used.The results indicate that the system is capable of following the normal variation that occurs in the mill. The signal also very well reflect changes in operating variables such as ball charge level, pulp density and rotational speed. By studying the nature and different features of the signal one can get a better understanding of milling circuit dynamics. Another feature of the technique is the possibility for an operator to continuously follow the grinding process and thereby run the process under optimal conditions."

Jan 1, 2003

By R. Shiva Kumar, G. E. Sreedhar, Rajan Kumar, K. Suresh, A. K. Aketi Veera, M. Narasimha, P. S. Jodan

"In most of the coal washeries, Dense Medium Cyclone’s (DMC) are deployed to treat coarse coal fraction in the range of 50-0.5 mm. DMC’s are very popular due to its ability of high tonnage, ease of operation and effective separation at high near-gravity material (NGM) in feed coal. The ease or difficulty of washing is merely depending on the NGM fraction present in run of mine coal. However, the quantitative effect of NGM on DMC performance was not explored in the literature. Hence, in this investigation, the influence of NGM on DMC performance is focused. With the help of synthetically prepared coal mixture, the effect of NGM mass fraction on separation efficiency is studied in three different approaches. Firstly, by increasing the NGM coal fraction systematically from low to as high as possible; second by varying the distribution of NGM coal; and third by varying distribution of particles lying just above and below the near-gravity zone. Washability studies are also carried out to establish the theoretical yield for the prepared synthetic mixtures. Pilot-plant experiments are carried out in a 4-inch DMC with 1.4 operating separation density treating coal in the size range of 4 - 0.5 mm. From results, the partition curves are constructed by both density and size wise distributions. It is observed that at higher NGM coal fraction i.e above 60%, the performance of DMC is very poor with significant coal particles misplacement. In second approach with increased distribution at higher density fractions, the separation efficiency reduces. In third series the distribution of fraction in near-gravity zone doesn’t much effect the separation except the shift in separation density. It is observed that smaller size (-0.5 mm) coal particle having high NGM content seems have a profound effect on DMC performance leading to significant fines misplacement to wrong products."

Jan 1, 2018

By S. Z. Shafaei

An experimental investigation has been carried out using a laboratory scale Denver flotation cell. For evaluation of cokeable coal of Alborze Sharghi coal washing plant, the full factorial method was used to statistically design and analyse the experiments. The 2 factorial interaction model were developed for combustible recovery and ash content as response and diesel dosage, conditioning time, feed percent solids and rotor speed as factors. Model validation and residual analysis were con-ducted and results indicated that the fitness, predictability power and residual distributions of models were good. The effect of parameters and interactions were examined and it has been demonstrated that rotor speed, solid percent and interaction between diesel dosage and solid percent were more important terms of all responses. A product with approximately 78% combustible recovery and 10% ash content was obtained at 4000gr/ton diesel fuel oil (high level), 30 sec conditioning time (low level), feed percent solids of 15% (low level) and 800 rpm rotor speed in appropriate condition.

Jan 1, 2014

By S. M. Bradshaw, V. Rocher, L Kabondo, B. Combrink, C. A. Snyders

Media losses are a significant contributor to the operational cost in a dense media separation (DMS) circuit. Of these losses, up to 80 wt% can occur on the drain and rinse vibrating screens. Although these screens are an integral part of any DMS circuit, surprisingly little work can be found in open literature regarding the effect of aperture configuration on the drain rates (draining water and medium). To establish the effect of slot aperture size, experiments were conducted on a 0.6 x 1.2 m vibrating screen with polyurethane (PU) panels at slurry densities between 1.6 – 2.8 kg/L, and volumetric flow rates of 19 – 25 m3/h for both ferrosilicon and magnetite. Results showed that an increase in the volumetric flow rate led to an increase in drainage rate, moisture content and medium carryover. Once an optimum volumetric flow rate was exceeded, a further increase in flow rate resulted in a decrease in drainage rate with a sharp increase in moisture and medium bypass to the oversize stream. An increase in ferrosilicon slurry density led to a decrease in drainage rate with an increase in moisture and medium bypass with each of these rates increasing as the slurry density increased. For magnetite, a gradual decrease in drainage rate was observed with increase in slurry density and volumetric flowrate beyond the screen optimum point. It was found that an increase in aperture size from 0.63 x 8.8 mm to 0.8 x 8.8 mm to 1.0 x 13 mm resulted in an increase in ferrosilicon drainage rate of between 1.3 - 1.8 m3/m2/h depending on the flow rate and slurry density with a reduction in moisture and medium carryover of between 1.0 – 1.2 % and 14.1 – 20.2 kg/t/m respectively. For magnetite, the drainage rate increased between 1.0 - 1.4 m3/m2/h as the slot width increased from 0.63 x 8.8 mm to 0.8 x 8.8 mm while an increase in slot length from 0.63 x 8.8 to 0.63 x 12 mm only resulted in an increase in drainage rate of 0.1 - 0.5 m3/m2/h.

Jan 1, 2018

By N. Jovanovic, A. Vazirizadeh

"The main objective of this study is to find a solution to design a mass flow observer system with the minimum required sensors and maximum observability for a mineral processing plant. The second objective is designing a mass flow observer configuration with high reliability to manage sensor failures. This configuration will provide a robust monitoring system that increases plant availability and process measurement fault detection. Furthermore, the monitoring system is expected to improve process efficiency. In this investigation, the procedure of designing an observer system is presented along with three models to design the sensor network. The advantages and disadvantages of each models are discussed and finally the models result for an industrial case are presented and analyzed. INTRODUCTION The concepts of observability and redundancy of mass flow are directly linked with the ability to solve and estimate the mass flow. There are hundreds of streams in a process plant flowsheet, and for technical and economic reasons it is not possible to measure all mass flows. It is thus important to know for a set of measured streams, which of the unmeasured streams can be estimated. The concept of observability deals with this issue. It is also valuable to know whether a measured mass flow of streams can be estimated even if a sensor fails for some reason. Redundancy deals with this failure question. A stream is said to be observable if it can be estimated by using the measurements and/ or mass conservation equations. Also, a stream is redundant if it is observable even when its measurement is removed. Observability and redundancy analysis can be exploited for adding new measuring instruments. It can also play a useful role in efficient decomposition and data reconciliation problem (Narasimhan and Jordache 1999). The value of an observer system cannot be justified without considering its benefits. This justification is done through evaluation of data reconciliation, gross error detection and improving process performance such as outlined below:"

Jan 1, 2018

By Osvaldo A. Bascur

One of the most vigorous of the continuous improvement methodologies is Six Sigma. While usually associated with improving manufacturing and product quality, leading manufacturers are using it to improve their extended supply chain and logistics capabilities. At the same time they are improving reliability, some companies have cut hundreds of millions of dollars of fat out of their supply chain. Mine to Mill optimization is a transformation of culture from processing tons to processing a quality feed size distribution which reduces the overall operational costs and add the highest value to the mine. This is not a constant endeavor. As such, a dynamic performance monitoring and diagnosis is necessary. We will review a systemic way to performance improvements and avoiding metal losses from the blast to the metals. We show the requirements of using raw data to analysis the data to define operational maps which provide assistance to run the mine and mill. A case study is provided with the mine and mill data was integrated combining process control and quality information resulting in reduction of water and energy consumption while improving the overall value of the mine. The results of reengineering the current system with this SIX SIGMA Strategy had the following results: an increase of ore milling: 4.6% decrease of mil power: 3.9%, decrease of fresh water consumption: 6.8%, with a total of net profits: US$ 31.8 million, the PI System infrastructure contribution: US$ 7.95 million. These estimates were for the period 2009/04/04 to 2009/12/31.

Sep 1, 2012

"The JKMRC researchers have been redeveloping the suite of breakage testing techniques to more realistically align with the breakage environment in comminution equipment. Computational modelling, especially with the DEM, has highlighted the modes of impact and contact, along with the energies of these interactions in a wide range of equipment. This has driven the need to match these modes in laboratory ore characterisation tests. The objective has been to build a continuum of breakage tests and associated models that span the required range of breakage forces and environments. The ore sample is subjected to a sequence of tests covering: abrasion (surface breakage) of angular through to smoothed particles; single particle impact from high energy single impact breakage down to low energy; incremental breakage covering 60 mm down to 50 µm particles; particle strength distribution; and bed breakage over a range of compression and energy input. These tests are suited to multi-component ores with a distribution of strengths. A modelling technique is also being developed to utilise primary breakage for modelling breakage under different types of confinement. This paper draws together these techniques, previously published by the authors, into a coherent whole. The suite of tests is approaching the point where a fixed set of tests can be used to model the performance of a full range of equipment, removing the need to conduct repeat ore characterisation tests for each different piece of equipment incorporated in a circuit design. This path should open up the application of different circuit configurations and novel equipment in comminution circuit design.1 INTRODUCTION Comminution modelling utilizes a wide range of ore characterisation techniques and methods to deal with the range of comminution equipment available for production use. In general, the tests have been designed to correlate with specific pieces of equipment, using calibration factors to provide the link between the small-scale test and industrial-scale performance. The majority of tests focus on estimating the power requirement of process equipment to achieve a desired throughput and grind size. Overall, this approach has achieved acceptable outcomes in the past, but the reality is that equipment sizing suffers from considerable uncertainty, in excess of ±20% is not uncommon. This uncertainty is covered by safety margins and automatic scaling factors in equipment selection. In striving to improve reliability, the industry tends to add more adjustment factors to the tests, and design margin rather than question the basic validity of the testing process. As the tests are often correlated to production equipment via carefully guarded databases, they are also locked into historic operating inefficiency, not providing direction or revealing opportunities to improve production efficiency in comminution equipment or circuits. Safe in the knowledge that they are achieving the expected production based on test work predictions, a site is unlikely to set their sights on reducing specific energy consumption by 10%."

Jan 1, 2018

By B. Orberger, J. M. Milazzo, S. B. Blancher, J. Lützenkirchen, J. L. Dubos

"Industrial dusts are commonly agglomerated using empirical recipes with binders such as bentonite, while Sludges are agglomerated into mixes. Those materials contaminate the products, are expensive and generate significant amounts of slag. Achieving cold dust agglomeration with little or no binder requires understanding the controlling parameters in order to predict and optimize the process behavior. This in turn necessitates comprehensive dust characterization to base predictions on measurable characteristics. In the present work we collected 13 Mn-rich dusts over all the process chain: feed fines, smelting, and refining dusts, as well as ferromanganese alloy dust. This is the first systematic study of dusts along the Mn-processing chain for chemical, physical and mineralogical parameters. X-Ray Diffraction, Qemscan® and laser granulometry analyses show that the mineralogy, Particle Size Distribution (PSD) and morphology evolves from complex heterogenous to simple, homogenous along the process chain: The mineralogy of the primary ore dusts shows various hydroxides, oxides, carbonates, tectosilicates and phyllosilicates. The furnace dusts contain oxides, tectosilicates and carbonates with volatiles, while the refining dusts present only oxides and metal. Finally, the Metal dust is nearly pure metal. Particle morphologies and PSD vary from jagged, irregular particles with broad PSD (>1 mm to <0.3 µm) to smooth and spherical with narrow PSD (100 µm to <0.3 µm). The Metal dust is an exception with angular particles. The Cationic Exchange Capacities (CECs) of all samples range from 0 to 22 meq/100g. Specific surface areas (SSAs) range from <0.1 to 27m²/g, and seem to decrease with from ore feed to Metal dust. This may be due to the disappearance of hydrated and/or sheet-bearing minerals, since a smaller grain size usually implies an increased SSA. The zeta potential varies strongly over the range of the samples tested. However, beside the Gabon ore which has an Isoelectric Point (IEP) ~ 4.1, the other IEP ranges between 2 and 2.5."

Jan 1, 2018

By F. Karakas

Organo-bentonite production enjoys important applications including solvent based paints and, more importantly, the production of polymer/bentonite nanocomposites. Quarternary ammonium salts in this regard are still considered as the most versatile reagents in the process of hydrophobization. In this study, a purified form of Resadiye region bentonites, which is one of the most significant sodium bentonite deposits in the world, was used. The raw Na-Bentonite was typically characterized by chemical analysis, XRD and DTA analysis and more importantly for its cation exchange capacity (CEC). Other technological properties such as swelling index, pH, apparent viscosity, water absorption, oil absorption were also conducted on the raw bentonite. The mineralogical analysis of the raw bentonite reveals that it contains about 80 % montmorillonite together with other associated gangue minerals including feldspar, quartz, calcite, dolomite, coloured impurities and other clay minerals. The raw bentonite was subjected to two stage processing involving a series of hydrocylones. Different apex and vortex diameters and different pressures were employed in order to produce a bentonite concentrate with 95 meq/100g CEC from a CEC of 71 meq/100 g. This high quality concentrate was used in the production of organo-bentontonite. The modification was performed with two different quaternary amines, i.e. Trimethyl Phenyl Ammonium Chloride (TPAC) and Hexadecyl Trimethyl Ammonium Bromide (HDTMA-Br). In the modification procedure, three parameters, i.e., adsorption density, zeta potential, swelling index and apparent viscosity were studied simultaneous-ly from the same suspension to identify both the mechanism of the process and also the degree of hydrophobicity. Adsorption measurements were made as a function of conditioning period, pH, and reagent concentration. Simultaneous examination of the adsorption density, zeta potential and apparent viscosity enabled us to pinpoint the optimum region of hydrophobicity which was subsequently tested by settling and critical coagulation concentration in both water as polar and toluene as nonpolar solvents. The results are analyzed in the light of experimental data.

Jan 1, 2014

By Lilong Huang, Xiang Zhao, Yuan Long, Li Shi, Guowang Zhang, Xiao Xiao

"Vertical stirred mill is expected to upgrade the iron concentrate by further size reduced efficiently. The tests for fine grinding of iron ores from Baiyun Boyu iron ore, Baogang Goup, iron contained tails of Cu-Pb-Zn ore in Wanguo ore, Xiaoshalong iron ore in Qinghai were conducted in this paper. The data of appropriate grinding fineness, optimum grinding conditions and energy consumptions obtained from the test were used to select appropriate scale of the vertical stirred mill, optimize the parameters of the grinding process and upgrade the iron concentrate of the iron ore dressing plant or design the new ore dressing plant. Based on the laboratory tests, industrial system of regrinding and magnetic separation with vertical stirred mill as the regrinding mill in micro-fine grained iron concentrate upgrading has worked out very well. The grade of Fe in iron concentrates has increased to about 65.0% (by 4.0~6.5 point percent) when the iron concentrates were reground to designed fineness and the specific energy is 5.0~7.1kWh/t. The system of regrinding and magnetic separation is proven to be eco-efficient in iron concentrate upgrading."

Jan 1, 2014

By T. V. Vijaya Kumar

Most of the iron ore washing plants set up in India consist of sizing of the ore by dry / wet screening, washing and classification by screw classifiers followed by multi-stage hydrocycloning of screw classifiers? overflow. The underflow of the hydrocyclones forms the concentrate which is used for pellets making. As the cut-point of hydrocyclones is generally at 20 microns, relatively lower diameter cyclones in a cluster with parallel feeding are used. This is found to, often, result in choking of the spigots, at times, by extraneous material as well reporting along with the slurry. It is observed to lead to sub-optimum performance of the cyclones with loss of iron values into cyclone overflow and thereafter into tailings. Analysis of data of an operating beneficiation plant (Beneficiation Plant - 1, BP - 1) of M/s Jindal South West (JSW) Steel Limited, Karnataka, India over a period of one year indicated that weight recovery of the concentrate from two-stage hydrocycloning was 45% (with respect to feed to the cyclones) and assaying 63.43% Fe, 4.43% SiO2 and 2.32% Al2O3. CSIR - National Metallurgical Laboratory - Madras Centre (NML - MC), India developed flotation process for processing screw classifier overflow with a view to improve the recovery of ultrafine iron values from it. Detailed investigations at laboratory scale flotation column and on-site pilot plant trials proved that the production of the concentrate and productivity of the plant could be enhanced by adopting reverse cationic column flotation technology. It was established that a typical screw classifier overflow analyzing 60.54% Fe, 5.95% SiO2 and 3.67% Al2O3 could be upgraded to 64.21% Fe, 2.64% SiO2 and 2.20% Al2O3 with 82.7% weight and 84.7% Fe recovery. This translates into an increase of 80% in weight recovery of the concentrate compared to what is being obtained, at present, by two-stage cycloning. It had an added advantage of reduced SiO2 in the concentrate. Thus, SiO2 in the final concentrate could be reduced to 2.64% from 4.43% by adopting column flotation. The concentrate so generated meets the stringent specifications, especially in terms of alumina in it(should be less than 2.50%) for pellets making. Later, JSW Steel Limited set up the flotation plant in BP - 1 based on the process developed by NML - MC and was commissioned in 2010. Keywords: iron ore, washing, ultra fines, alumina reduction, column flotation

Sep 1, 2012

By J. Botula

In the region of the North-Bohemian Coal Basin and its environment, there, in a row of places, are found the accumulations of rocks of the sedimentary and pyro clastic origin, the preliminary composition of those shows the possibility of their being utilized for the production of ecologically sparing natural Fe- and Ti- pigments and filling substances. In many places of the regions of Chomutov and Podborany and near Bilina and also in other places, there are found raw stocks perspective for the preparation of yellow up to ochre-brown, red, brown-red and green dyes. The target of project is the verification of dispensable reserves, their mineralogical composition and chemical and physical attributes, verification of treatment ways of Fe-and Ti-pigments separation (hydrocyclones, magnetic and electrostatic separation) and their stabilization and technological painting attributes for applications in colors, coating and plastic masses, mortar mixtures etc.

Jan 1, 2014

By S. Banisi, A. Haji-Zadeh, H. Asadi, M. Maleki-Moghaddam

One area in AG/SAG milling field which has received a great attention is the optimization of liner design for any application to increase the availability of mills. The Gol-E-Gohar iron ore concentration plant uses three 9m × 2.05m autogenous mills (AG) in parallel in a dry operation. The AG mill shell is lined with three series (57 cm each) of 36-row liners. Due to large variations in feed characteristics and inadequate blending, the performance of AG mills has been lower than the target value. Therefore, to improve the comminution efficiency, the optimization of the design of AG mill shell liners was applied in this plant. By simulation it was found that increasing the liner lifter face angle from 7 to 30° while maintaining the original lifter height (i.e., 22.5 cm) could provide an appropriate charge trajectory. Measurement of the wear profiles of shell liners indicated that the wear along the liner length was not uniform and the highest wear occurred between 0.5 m and 1.2 m of the mill length. A new liner design was proposed by redistributing the metal from parts with a lower wear rate to the parts with a higher wear rate to arrive at a uniform wear profile along the liner length at the liner removal time. The non-uniform shell liner was constructed and installed in one of the three parallel dry AG mills. It was found that the first and second liner designs increased the mill throughput by 2.6 and 7.5%, respectively. After conversion to SAG milling on the account of liner change, 18% (from 413 to 489 t/h) increase in throughput was realized. It was predicted that the non-uniform liner designs will increase the liner life time by 10% and will reduce the scrap metal from the current value of 59% to 50%.

Jan 1, 2014