Search Documents

By Mohammad Mainul Hoque, Linhan Ge, Ai Wang, Geoffrey Evans, Subhasish Mitra

"Dispersed phase interactions involving bubbles and particles in the turbulent environment play a significant role in the flotation process. The conventional collision models only account for the deterministic rather than the stochastic behavior of turbulenct flow. What the bubble-particle collisions would be like remains an open problem due to the complex nature of turbulent flow. To address this research question, the present study aims to quantify the bubble-particle collision efficiency incorporating turbulence using the computational method. Multiple solid particles were released to interact with a single stationary rigid bubble (non-deformable interface). Effect of particles Stokes number, turbulent intensity (TI) and integral length scale on the bubble-particle collision efficiency (Pc) was examined. Large Eddy Simulation method (LES) was used to compute the continuous phase. Fluctuating velocity required at the inlet boundary condition was derived from Gaussian energy spectrum to generate the upstream turbulence. Discrete Phase Model (DPM) is used to simulate particle trajectory. The characteristics of turbulent flow were analyzed through Energy spectrum and energy dissipation rate. The critical initial releasing radius of the annulus, where Pc equals zero, reaches up to 1.5(Rb+Rp) under high turbulent intensity (TI) 20.48% compared to 0.23(Rb+Rp) calculated from the traditional Pc model. Pc decreases as the distance of initial releasing annulus between bubble centre increases. Pc increases as particle Stokes number increase up to 0.66. The collision efficiency for particles of St less than 0.38 is higher under TI 11.78% compared to TI 4%.INTRODUCTION To increase mineral recovery, interactions between bubbles and particles are essential. All flotation devices achieve it through introducing some level of turbulence into the system by increasing specific energy dissipation rate. Figure 1 shows three different flotation equipment, traditional floatation cell, Concorde cell and cyclonic-static micro-bubble flotation column (FCSMC), with different turbulence generation mechanisms – impeller, down-flow liquid jet and pump recirculation, respectively."

Jan 1, 2018

By Liu Xiaodong, Jiang Meifen, Kou Xiaoyan, Lu Xianjun

"Two low grade calcium bentonite (Ca-bentonite) from Hejia (HJ) and Boteng (BT), Shandong, China, mainly contain montmorillonite and quartz, and slightly feldspar, calcite, and montmorillonite content are 32.37% and 55.90%, respectively. In order to examine the feasibility to produce activated clay to meet the standard of Chinese chemical industry (HG/T2569-2007), three types of industrial production process are proposed according to the screen test. The first process is grinding the raw bentonite to -200 mesh and then activating. The second is to activate the raw bentonite directly, and then classify the production to -200 mesh. The last one is to activate the raw bentonite after purification. Three parameters, which are sulphuric acid strength, ratio of liquid to solid and treatment time, are optimized via orthogonal test for every process. The preliminary test indicates that it is feasible to produce acid bentonite of difference quality. For the sample of HJ, milling the raw to -200 mesh first and activating afterwards, the parameter is at 9% acid strength, the ratio of liquid to solid 2, the time 4 hours, temperature 90°C, the products can meet the qualified grade for animal and vegetable oils refining. For the sample of BT, milling the raw to -200 mesh first and activating afterwards, the parameter is at 15% acid strength, the ratio of liquid to solid 2.5, the time 2 hours, temperature 90°C, the products can meet the qualified grade of high decolorization for petroleum products refining. For the sample of BT, adopting purification to -325 mesh by stirring and rubbing at first, and then activating at 9% acidity, under the conditions that the ratio of liquid to solid is 2, the time is 2 hours and the temperature is 90°C, the products can meet the first grade of high activation degree for petroleum products refining."

Jan 1, 2014

By Song Z. Guo

Calcite and magnesite are both carbonate minerals and their crystals belong to trigonal system. Flotation tests were carried out to investigate the flotation behaviors of calcite and magnesite. The test results show that the floatability of calcite and magnesite under different grinding environment had obvious differences. The floatability of calcite using sodium oleate as collector after dry grinding is better than wet grinding, but the floatability of magnesite after wet grinding is better than dry grinding. The XPS surface elements test and zeta potential measurement show that, wet and dry grinding process makes the distribution difference of surface anion and metal cation, then influence the floatability of the two carbonate minerals using sodium oleate as collector. Difference of the carbonate crystal structure and solubility properties was also investigated. Research shows that crystal structure difference of calcite and magnesite causes the difference of solubility, which can influence the flotation behaviors under different grinding environment. Keywords: carbonate mineral, crystal structure, solubility properties, flotation, surface character

Sep 1, 2012

By J. Broadhurst

"A number of metal supplying industries have in recent years seen the compilation of life cycle inventories (LCIs) and life cycle assessments (LCAs). The activity has largely been driven by the interest of ultimate metal users, such as the automotive industry, in the interest of designing more sustainable products. Often, the compilation of such inventories has been little more than an auditing exercise. However, the process of conducting an LCA can have more value, guiding designers and operators to points within the technology train where significant emissions and impacts originate. The LCA product can thus be used to inform on-site environmental management, and, where process data is used to construct dynamic operational models, to support strategic decision making in the realm of project planning and technology selection. LCA thus serves as a valuable tool to support the industry’s drive to support the sustainable development of the societies in which it operates.This paper reviews and compares the priorities of environmental and closure planning in the design phase, with environmental management and auditing during operation, and with green procurement of minerals and metals products. It shows how life cycle assessments of various complexities can be used to reconcile these various objectives, ensuring that the latter, critical to business success, can be addressed from the outset in a new project. The paper then reviews a case study of the use of LCA in the base & precious metals industry, where the complexity of the operation disallowed the simpler auditing process so that a detailed process understanding had to be built up in order to compile a meaningful life cycle inventory."

Jan 1, 2003

By Pengbo Chu, James Finch

Bubbles around 1 mm diameter provide the high interfacial area for capture and transport of hydrophobic particles in flotation. The formation of such fine bubbles is commonly achieved by addition of frothers that appear to simultaneously retard coalescence and promote break-up. High inorganic salt content in process water can substitute for frother. In this work we focus on the action of salt (sodium chloride) on formation of bubbles by break-up. An experimental setup that isolates break-up from coalescence was employed. A pocket of air is exposed to controlled mechanical turbulence to produce single bubbles by the induced deformation of the air and the events imaged. The presence of salt is shown to produce smaller bubbles than in water alone. Comparison with a similar study on frothers is made. The argument is advanced that the presence of frother and salt creates surface tension gradients at the air/water interface which add to the mechanical energy of the deformation and break-up process.

Jan 1, 2014

By A. E. Sobolev

The kinetics of hydrochemical oxidation of antimonite in solutions of nitric acid was studied using the rotating disk method and the factor experiment design. The dependences of the antimonite?s oxidation rate on concentration of nitric acid solutions, temperature, disk rotation frequency, and duration of interaction were determined. The adequate kinetic models allowing calculating the specific oxidation rate at any combination of the values of the influencing factors were obtained. The oxidation process is found to proceed in a mixed mode, close to chemically controlled. Gradually, as the sediments of elemental sulphur and Sb2O5 accumulate on the disk surface, the process becomes controlled by internal diffusion. The observed high (more than second) order of the oxidation rate with respect to the concentration of nitric acid was explained by the autocatalytic action of the acid reduction products. The apparent activation energy depends on the stage of interaction. At the initial stage (in a mixed mode of the process proceeding), it depends on nitric acid concentration and varies from 31.5 kJ?mol?1 (in 2 M HNO3) to 36.1 kJ?mol?1 (in 10 M HNO3). This trend indicates the weakening of diffusion limitations with a nitric acid concentration increase. When the process is controlled by internal diffusion, the apparent activation energy was found to be 14.5 kJ?mol?1. The obtained kinetic characteristics enlarge the database on hydrochemical oxidation kinetics of sulphides and can be used for the elaboration of the recommendations for the effective comprehensive exploitation of antimony-bearing ores and concentrates.

Jan 1, 2014

By S. J. Neethling

"This paper examines the impact of several key variables on the performance of flotation cells. The study makes use of a simulator for the froth phase of the flotation vessel, as the main purpose of this study is to separate the impact of different variables from one another. In experiments it is very difficult to separate the effect of variables from one another as a change in a singe input parameter, such as air rate, invariably also affects many of the other key variables, such as bubble size and bubble bursting rates.In order to achieve this a base case simulation that is typical of many of the rougher cells found in sulphide flotation circuits was carried out. Four key variables, air rate, incoming bubble size, surface bubble size and the fraction of the bubbles flowing out of the cell unburst, were varied in order to obtain the system.s response.The most significant results were obtained when the bubble size was varied. An increase in the incoming bubble size has the effect of reducing the pulp zone recovery, but increases the froth zone recovery. If it were possible to vary the incoming bubble size without influencing the overflowing bubble size, the impact of the change would be unclear because of these two competing effects. The effect of a change in the overflowing bubble size has an opposite effect on the froth recovery, with larger bubbles resulting in lower froth recoveries.A final interesting result is that all the effects examined affect the process to a similar degree, which implies that none of these variables can be disregarded, either in industry or in further research."

Jan 1, 2003

By G. Kumar

Water for domestic consumption is an essential right of society, which must be over secured. Water reclamation and reuse provides a unique and viable opportunity to augment traditional water supplies. As a multi-discipline and important element of water resource development and management, water reuse can help to close the loop between water supply and wastewater disposal. Effective water reuse requires integration of water and reclaimed water supply functions. During the coal mining activities, large quantities of water get contaminated and loses its potability characteristics. On an average, in coal mine operation, each coal mine discharges effluents at a rate of nearly 0.5 MGD and thereby wastage of nearly 50 MGD of water takes place per day from the famous Jharia Coal Field of the Dhanbad District. In this paper, attempt has been made to control the extremely high turbidity of mine waste water by using different coagulants and it is observed that ferrous sulphate is the most effective coagulants followed by alum, ferric sulphate and lime. Also combinations of coagulants are used for getting the optimal results. Further steps were also discussed to make this water potable and a scheme of low cost water supply system of mine waste water has been suggested under the Water Management Strategies. Keywords: potability, turbidity, coagulants, water management strategies

Sep 1, 2012

By P. K. Arya

Huge quantity of copper is lost in Crown, Sill, Rib Pillars, hanging wall, foot wall and unexploited ore bodies in several closed underground copper mines and old worked out stopes of Hindustan Copper Limited at Mosaboni and other places. These mines might have been uneconomical to work with conventional mining methods. However, huge quantity of mineral reserves is lost due to their closure. Chemical and in-situ bio-wash leaching, if tried can provide an answer to facilitate the recovery of metallic values economically. Encouraging results were obtained during an experiment at North Badia Mines at Mosabani in the past. Though the experiments were not completed but whatever results obtained were very encouraging and can be successfully tried to make it viable. The results of the experiments are discussed here and a plan is suggested to recover copper from such mines.

Jan 1, 2014

By Xu Wang, Bang Chen, Xiujian Luo, Wei Tang, Xiao’ou Xia, Fangming Liu

"The inertia cone crusher has lots of advantages, such as big crushing ratio, fine particle size, material layer crushing, good passing tramp iron performance and stable technical index, realized open crushing circuit and simplified crushing flowsheet. The crusher was input to China’s Beijing General Research Institute of Mining and Metallurgy (BGRIMM) from Russia’s Mekhanobr-Tekhnika Research & Engineering Corporation at the beginning of the 1990s. This paper introduces that after years of absorption and innovation how Chinese researchers optimized and creatively designed about transmission mechanism, bracing structure, kinetic parameters, lubrication system, dust sealing system, damping system and hydraulic control system etc on the basis of keeping its advanced theory and unique structure, therefore the crusher’s stability was raised and the usage cost was reduced greatly. Accordingly the inertia cone crusher in China has been widely used in many fields, such as mineral resources and the recycling of metallurgical slag. The achievement in cooperation was fully affirmed by governments of Russia and China, and cooperation of science and technology in the mining and metallurgy industry between Russia and China is promoted greatly. INTRODUCTION From the early 1950s, the former Mekhanobr Institite(now Mechanobr-Tekhnika Research & Engineering Corporation) devoted itself to the research of inertial cone crusher and put it into industrial application in the late 1980s. Inertial cone crusher is like a maverick flower in the field of crusher. With its excellent performance and excellent application effect, it shocks the world and is destined to shine with a bright future. In the early 1990s, the chief leaders of the Beijing General Research Institute of Mining and Metallurgy (BGRIMM), Academician Sun Chuan-yao and Professor Zheng Baochen, captured the extraordinary performance and strong vitality of inertial cone crusher with keen eyes. So the two big institutes started the cooperation to introduce inertial cone crusher to China. Since then, Inertia cone crusher has been able to flourish in China and have achieved impressive results with two institutes’ continuous effort."

Jan 1, 2018

By Gorki Davila, Irineu Brum

"Brazil has large reserves of coal (32 billion tons) located predominantly in the south of the country. Despite the relative ease of exploitation, these resources have been underestimated as a source of energy. Currently the country's strategic planning aims to minimize the gap between coal and resources traditionally used in the Brazilian energy matrix. In this scenario the processing of Brazilian coal by flotation appears as a promising alternative, having been successful in mineral systems containing fine particles This paper aims to study the overall process of flotation for a specific Brazilian coal. The material used in this study consists of fine coal that is usually discarded as waste and deposited in the tailings dam. The objective is to recover carbonaceous matter and reduce the ash and contaminants grade. The variables analyzed were the influence of size particle, solids concentration in the pulp, the concentration of surfactants and frothers to be used. The results showed that it is possible, from a feed with around 65% of ashes, to obtain products with approximately 35% ashes with mass recoveries about 40%. The types of collector reagent and foaming employees result in different concentrates. This study also presents a preliminary analysis of the effect of water recovery in concentration parameters."

Jan 1, 2014

By P. Gao, J. W. Yu

"Pre-concentration is a necessary step for upgrading low-grade iron ores, and its aim is to remove gangue minerals for improving efficiency of downstream separation process. The most important pre-concentration technique for iron ores, including hematite, siderite and limonite, is magnetic separation based on the appreciable differences between the desired iron minerals and gangue minerals in magnetic susceptibility. In this paper, the separation efficiency of one-stage low-intensity magnetic roughing combined with two-stage high-gradient magnetic scavenging for the pre-concentration of a low-grade hematite from Donganshan was investigated. It is a BIF type of ore containing hematite, magnetite and a bit of siderite, and an average content of Fe is about 34.6%. The effects of grinding fineness and magnetic field intensity for scavenging I and II were studied and optimized. The results showed that a magnetic preconcentrate assaying 42.7% with a recovery of 95.4% was obtained under the conditions of ore grinding fineness of -74 µm 70%, magnetic field intensity of 300 mT and 800 mT for scavenging I and II, respectively. Over 20% of the feed was rejected as the final tailings assaying 6.4% Fe. Meanwhile, the XRD, iron chemical phase and SEM analyses of different stage products revealed that hematite, magnetite and siderite could be recovered successfully by magnetic separation. However, some ultra-fine hematite particles (-10 µm) were difficult to be captured by magnet, and lost in the final tailing, resulting in lower iron recovery.INTRODUCTION Donganshan iron ore belongs to sedimentary-metamorphic iron formation called banded iron formation (BIF), which is formed in the Precambrian with a layered structure composed of ore bodies (Shen, 2012). Such type of iron deposit contains various iron-bearing minerals like hematite, magnetite, and siderite, suggesting it may be amenable to pre-concentration with magnetic separation. The pre-concentration process is effectively applied in recovering hematite, magnetite and siderite from iron ore, due to its benefits of further upgrading iron ore and improving separation efficiency. The most important pre-concentration technique for iron ore is magnetic separation, including low-intensity magnetic separation and high-gradient magnetic separation, based on the fact that there are appreciable differences between the desired hematite, magnetite or siderite and the gangue minerals in magnetic susceptibility."

Jan 1, 2018

By V. V. Zakopaylo, M. V. Lukyantseva, V. A. Ignatkina, V. A. Bocharov, L. C. Khachatryan, D. M. Altynamanov, A. A. Kayumov, R. H. Sharipov

"This research was aimed to explain the reasons of low floatability of tennantite from refractory pyrite ores of non-ferrous metals and to create a reagent regime for selective increasing a recovery of copper sulfide minerals from arsenic-containing copper pyrite ore. ?opper-zinc ore of the Uzelga deposit has 89% of pyrite, some part as melnikovite; copper is assayed as 3.58% of tennantite and 0.25% of chalcopyrite; there is 2.19% sphalerite. Sulfide minerals are very finely disseminated. Tennantite is genetically related to primary copper sulfides. Graphene was identified on the surface of tennantite by a transmission electron microscopy (TEM) method. The recovery of tennantite was rose up by using the collector M-TF. M-TF is the mixture of diisobutylditiophosphate (DTF) and O-isopropyl-N-methyl (ethyl) (TC) in the certain ratio. M-TF change up a kinetic of copper sulfide flotation in a slightly alkaline medium, but pyrite has slowly floatability at this moment. A depressing effect of thiosulfate ions in a liquid phase of pulp flotation tennantite from pyrite ore has been established. A copper recovery up 14.2% (from 67.7 to 82.0%) into a copper concentrate level off copper grade of 18.65% (butkx) and 18.68% (M-TF) has been increased by the new technology with M-TF compared to a standard technology with butkx. A main copper recovery up to 50 % in an inter-cycle copper concentrate assaying 19-21% Cu in case of using M-TF was gotten. A zinc concentrate with recovery of 50% and a zinc assay of 41.76% by a standard flow sheet with butyl xanthate was obtained. A zinc recovery of 70.3% with a zinc grade of 44.17% by the M-TF technology was achieved.INTRODUCTION The pyrite copper-zinc ores of the Urals region are considered refractory. The distinctive features of these ores include a high content of pyrite (90-95%), the presence of arsenopyrite and arsenical pyrite, and the simultaneous presence of chalcopyrite, bornite, tennantite with the predominance of the latter (Andreasen et al.,2008;.Dobrotsvetov, 2009; Chanturiya et al. 2016). The flotation properties of tennantite differ from those of chalcopyrite (Xumeng Chen, Yongjun Peng, Dee Bradshaw. 2014), which is the reason why a comprehensive study was under taken of the flotation activity of tennantite and a process for its recovery was developed. The proposed agent treatment and flotation process make it possible to produce salable copper and zinc concentrates."

Jan 1, 2018

By Jin Duan, Qi Zheng, Bo Yan, Li-cheng Ma, Xiao-kui Che

"The aim of this study was to develop an approach for the selectively removal of Zn(II) from heavy metal-bearing-wastewaters produced by gold chemical industry using magnetic chitosan based adsorbents. Chitosan beads were prepared by cross-linked modification of Fe3O4-chitosan bead using epichlorohydrin as the cross-linker. Both Zn(II) inprinted magnetic chitosan hydrogel bead (Zn-MCHB) and unprinted magnetic chitosan hydrogel bead (MCHB) were prepared and batch adsorption experiments were used to evaluate their adsorption capacities and selectivities. Single adsorption of Cu2+, Pb2+, Zn2+ and Ni2+ showed that both MCHB and Zn-MCHB adsorbs all the four metals and had an affinity in the order of Cu2+ > Pb2+ > Zn2+ > Ni2+. The binary adsorption revealed that the two adsorbents preferentially adsorb Cu2+/Pb2+ from Zn2+-Cu2+/ Zn2+-Pb2+ binary systems. However, MCHB does not show any selectivity in Zn2+-Ni2+ system. In contrast, Zn- MCHB preferentially adsorbs Zn2+ from Zn2+-Ni2+ binary system. Furthermore, the adsorption selectivity is predictable from stability constants of the metals with the amino group of chitosan. The information revealed in this work can be used for further applications in the treatment of wastewater containing a range of heavy metals from the gold chemical industry."

Jan 1, 2014

By A. N. Zagorodnyaya, T. N. Bukurov, Z. S. Abisheva, A. S. Sharipova

"The paper describes the results of stripping of copper production dusts by leaching with aqueous soda, nitric acid solutions and recovery from solutions resulting in the production of lead sulphate, tribasic lead sulfate (TBLS), ammonium perrhenate, zinc, copper-cadmium cake.The combination of two stripping operations under chosen optimal conditions allows the recovery of 98% rhenium, 82% lead, 92 % copper, and 96% zinc and cadmium each. The major amount of rhenium (~ 80%) is recovered at the carbonization stage, and other metals - at the nitric acid leaching stage.Lead sulfate was precipitated by mixing solutions resulting from carbonization and leaching. Tribasic lead sulfate was produced by dissolving lead sulfate in sodium hydroxide solutions. Rhenium was recovered from mother liquor resulting from lead sulfate precipitation by liquid-liquid extraction and zinc was recovered from raffinates. Trialkylamine (TAA) was used as an extractant for rhenium recovery and di-2- ethylhexylphosphoric acid was used for zinc recovery. Optimal liquid-liquid extraction parameters have been defined allowing the recovery of 96% rhenium in crude ammonium perrhenate and 94% zinc in sulfuric acid solution. Based on the experimental data, the flowchart for dust processing to produce salable products - lead, rhenium, zinc salts has been suggested."

Jan 1, 2003

By N. Johnson, J. Quinteros

With the general trend across all commodities towards the treatment of lower grade ores, it is becoming increasingly important to develop efficient protocols for comprehensive mineralogical characterisation to allow the development of the most appropriate strategies for processing an ore. In the case of silver, there are more than 200 known silver bearing minerals which can make it challenging to identify them. Knowledge of the deportment of silver within an ore is one of the factors used to determine an appropriate processing strategy. Automated SEM-based tools are commonly used for mineralogical characterisation but the low-grade together with the large number of minerals that are potential hosts for silver means that often, complementary analytical tools must be used in order to properly account for the silver. The work presented in this paper is a demonstration of the approach that should be taken when identifying the deportment of silver in complex ores. Three complex, low-grade silver ores were characterised using the approach. The insights from the mineralogical characterisation were then used to inform the metallurgical testing that was undertaken. The results from the batch flotation testing clearly demonstrate the importance of understanding the mineralogy in order to select the most appropriate metallurgical processes.

Jan 1, 2014

By S. I. Anufrieva, N. A. Permyakova, E. G. Likhnikeevich

"Russia’s rare metal reserves are composed of compositionally and structurally complex ores and are characterized by an increased content of natural radionuclides due to their geochemical similarity with rare metals. For instance, concentrates of Zashikhinsky daeposit are characterized by an increased content of uranium (0,06%) and thorium (0,59%); Beloziminsky deposit holds pyrochlore-apatite-magnetite-carbonate ores characterized by increased radioactivity (130 mkR/h) and containing 0,0016-0,0025% of uranium; Etykinsky deposit is characterized by columbite-pyrochlore-microlith mineralization with an average ore grade of 0,013% of uranium and 0,0020% of thorium; eudialyte concentrate of Lovozero deposit (Alluaiv area) belongs to Class II of mineral reserves. Industrial development of these mineral reserves involves the need to comply with environmental standards, public health requirements applicable to finished core and by-products, to take into account the amount and class of the generated radioactive waste, the possibility of disposal or recycling of the radioactive production waste. Concentration processes of radioactive rare metal feeds most often lead to a concentration of natural radionuclides and their accumulation in concentrates. Comprehensive hydrometallurgical processes are currently under development for such concentrates, aimed at producing salable products compliant with the radiation safety standards. The choice of the hydrometallurgical processing method for radioactive rare metal concentrates is based on the mineralogical component of the concentrate, textural and structural features, the distribution of valuable components and impurities, and the content of radionuclides. A systemic approach to the selection of processing methods, in particular integrating several methods, is an effective solution. Methods may not only be combined, but also inextricably linked with each other. Hydrometallurgical processing methods include leaching by acidic and alkaline agents; sulfatization for selectively decomposing the minerals and moving the bulk of U and Th into solution; fluorine extraction process. Methods of precipitation and co-precipitation, extraction (by liquid and solid extractants), sorption, and ion exchange are used to decontaminate the solutions by removing thorium, mezathorium, uranium, and their radioactive decay products. Agents used in hydrometallurgical processing of radioactive rare metal ores include sulfuric, nitric, hydrochloric, hydrofluoric acid, alkali (NaOH, KOH), sorbents (for example, AB-17) for sorption of uranium and extractants (mono- and bidentate organophosphorus compounds, diamides, etc.) for the extraction separation of rare, rare-earth, and radioactive elements."

Jan 1, 2018

By T. Khonthu

The purpose of this investigation was to evaluate the relationship between different milling procedures, viz. a ball mill and an IsaMill respectively, and the flotation performance of the different mill products. Two ores were used, viz. a base metal sulphide (BMS) and a platinum group mineral (PGM) UG2 ore. Flotation was used as a diagnostic to investigate whether the different milling procedures may have different effects of the floatability of the particles. The present study is part of a research programme investigating this question using a wide range of comminutiondevices and procedures. Similar particle size fractions from the different milling procedures were used in the flotation tests. The particles were characterized in terms of particle size distribution, morphology (using scanning electron microscopy and image analysis software) and rheology tests. The results have shown that in general when comparing similar feeds to flotation in terms of equivalent particle size distributions as indicated by the d80 value, the ball mill generally yielded better recoveries and grades in the case of the BMS and lower chromite recoveries in the case of the UG2 ore compared to the IsaMill. No significant differences were observed in the morphological or rheological characteristics of the particles subjected to the different milling procedures. Although the results appear to indicate that IsaMilling is less advantageous than ball milling in terms of the flotation performance for the two ores studied it should be emphasized that these results do not take into account the relative advantage which IsaMilling has over ball milling in terms of direct and indirect energy consumption and GHG emissions nor, most importantly, does it consider the platinum group element recoveries in the case of the UG2 which may have increased significantly as a result of the finer grind which the IsaMill produces after 4 passes compared to the ball mill after 64 min. Such results which will be reported is due course may show that the greater liberation expected after IsaMilling of the PGMs outweighs any disadvantages indicated in this study.

Sep 1, 2012

By V. Hema

Granular materials are widely used in process industries, such as chemical, pharmaceutical, cement, food, detergents, and fertilizers. Mixing, blending, calcining, reduction, heating, and granulation of these materials are frequently carried out in rotating cylinders. In all of these processes, the mixing and segregation of these granular materials is important as this controls the secondary phenomena in the rotating kiln such as heat transfer to the material. A significant amount of work is available in the literature but to date these efforts have not been able to capture the important parameters affecting the mixing and segregation in rotating kilns. In addition, the range of parameter values studied so far is rather limited. Simulations of granular materials are based on either discrete elements or continuum models. The discrete element methods (DEM) combine semi-empirical models for the inter particle interactions with the equations of motion from classical mechanics to simulate the explicit paths of all granules in a rotary kiln, thus yielding realistic predictions of the mixing process. This approach is very demanding computationally, which strongly limits the number of granules and the number of revolutions in a simulation. Continuum models dispense with the discrete particles and can therefore be scaled up more easily. But the constitutive relations that serve as the foundation for continuum modeling are difficult to come by, and often only applicable to specific systems and conditions. Here we have chosen DEM simulation for investigating the mixing and segregation behavior of granular materials in a rotating cylinder. This work is directed towards demonstrating the capability of the prediction of the mixing and segregation behavior of granular materials in a horizontal rotating cylinder through discrete element simulation. Further the effect of particle size and rotational velocity on the mixing and segregation behavior is investigated. The simulation results are quantified in terms of mixing index, mixing rate, segregation index and percolation index. Keywords: DEM simulation, granular mixing

Sep 1, 2012

By Marzio Piller, Girolamo Belardi, Jure Mencinger, Paolo Bozano, Gianni Schena

"The hydrodynamics of the Tri-Flo™, a two stage cylindrical cyclone used in dense media separation, is studied using Computational Fluid Dynamics. The flow field is simulated with an Euler-Euler Volume of Fluid two-phase approach and the Reynolds stress turbulence model.A unique feature of the device is that the separation medium suspension is pumped and introduced tangentially into the two cylindrical compartments while the raw feed is conveyed to the feed hopper and fed at the axial inlet. This feature allows to use less pumping energy and limits the unavoidable production of fines. The Tri-Flo™ complex flow pattern is little known but central to the efficiency of the separation.The velocity field is computed within the two compartments of the separator. The interface of the air-core that forms in the inner axial part of the cylindrical sections is identified and visualized. The numerical results for a reduced-size 100 mm ID Tri-Flo™ are compared against laser Doppler measurements on a transparent acrylic model (Chinè, 1995) operated with water. The robustness of the model and its prediction capability are verified.The possibility to accurately predict the velocity profiles within the vessel and their dependence on the main Tri-Flo™ operating and geometrical variables paves the way to a better understanding of the functioning of the separator, its design improvements and scale-up."

Jan 1, 2014