Search Documents

By Terri Jordan, Gregory Hempen, Thomas Keevin

Water-borne blast pressures from confined blasts were recorded as part of a submerged blasting program in Florida for channel deepening. The blasting was confined within the rock floor by stemming. Shot patterns of stemmed borings were recorded, as were two open-water shots. One hole of one shot was not confined properly, which allowed comparison of confined and a poorly confined larger charge weights per delay. The pressure data were intended to gain information on typical pressure measures from the rock removal program relative to impacts on marine organisms. Water-borne pressures from actual confined, rock-removal shots validate the hypothesis of lessened impacts to aquatic and marine biota.

Jan 1, 2007

By Marwan M. Mohammed, Hani S. Mitri, Wilfrid Comeaul, Baoyao Tang

In many parts of the world, rockbursts have become a major problem of mining at depth. As orebodies are being mined deeper, rockburst phenomena have become familiar to deep hard rock mines. Rockbursts are generally characterised by sudden release of energy in a volume of highly stressed rock, which can cause local violent failure of the rock mass around the opening. One method of controlling these failures is to precondition the rock mass by detonating fully confined explosive charges at the appropriate locations. This method known as destress blasting, was first tried in the deep South African gold mines (Roux et al., 1957), and was widely used later in Canada, United States, France, Poland and Japan.

Jan 1, 1999

By Ekin Güngor, Berkant Ozdemir, Erkan Bayrak, Serdar Ergün, Sedat Esen

"This paper presents the final wall blasting practices at Eldorado Kisladag Gold Mine in Turkey. Benchmark and improved wall control designs were explained in detail. Kisladag Mine has been implementing a high quality slope stability program on-site. The quality of pit walls is generally considered excellent, with very few wall failures being evident and with presplit hole barrels prominent in most areas of the pit. However, a minor scale slope failure occurred recently at the north-east section the pit. A project was initiated to diagnose the cause of the crest loss and evaluate ways to limit its effect on final walls. Final wall blasting practices and geotechnical designs were evaluated. The work presented in this paper showed that changes to the blasting and geotechnical parameters are required atthe north-east section of the pit. Geotechnical design changes were 10 m bench heights with 70 ° slope face angle at that specific area. Having implemented several geotechnical and blast design changes (elimination of the subdrill for the catch bench, appropriate primer location, more favorable blast tie-up and delays), the crest loss was minimized significantly (<1.5 m) (<5 ft)."

Jan 1, 2017

By Charles Deacon

The mining industry is constantly taking greater cognisance of their operating costs as a strategy to counter the effects of falling commodity prices. As a result, optimal operating efficiency is more important than ever. One such operation is that of blasting. Considering the relative increasing costs of explosives and accessories it is desirable to optimise the number of blast-holes fired by maximising their individual output. This achievement may now only be possible following the advent of higher technologies in the form of modified explosives and electronic detonators. This paper reviews and introduces some techniques of blast monitoring, types of operations where each is most suited, resulting modifications to blast designs, and identifies some pitfalls to watch out for when analysing the results.

Jan 1, 2000

By Douglas Rudenko

Have you ever had a neighbor complain about a blast one day, but says the next day’s blast was better, even though the Peak Particle Velocity (PPV) increased? How about neighbors that complain about a small trimming shot, but don’t complain about a big production shot? Have you ever reduced the pounds/delay and gotten more complaints ? Mine operators are often bewildered when trying to correlate blast design parameters to homeowner complaints. When complaints come, standard practice is to set up a seismograph in the neighbor’s yard to monitor the blast. Immediately after the blast, the neighbor usually reappears from the house wanting to know the seismograph reading. When told that the PPV was 0.1 in/set, well below damage levels, the homeowner explodes saying “Your machine is wrong”. Perhaps he is right. Understanding why people complain about blasting is not about PPV, it’s all about structural response. People could care less about how much the ground vibrates; they only care about how much their house vibrates. In this paper we will examine the primary factors that control structural response. Through the use of a large array of digital seismographs, the effects of two production blasts on a community surrounding a quarry are studied. The predicted structural response resulting from each blast is calculated at 175 seismograph locations. The predicted response is then correlated to previous research on human perceptibility to vibrations. The results of this analysis and correlation give a better understanding of what the residents actually feel in their homes. The detonations of two single-hole signature blasts are also recorded by the array of seismographs revealing the dynamic characteristics of the geology ‘surrounding the quarry. Once the influence of the geology was understood, blasts were configured to disrupt the natural rhythm of the site through the use of millisecond delays.

Jan 1, 2000

By L D. Lawrence

Certain blasting applications are more prone to the generation of significant levels of nitrogen dioxide post blast fumes, more commonly referred to as after blast smoke, generally ranging in color from dark yellow to bright red. This paper reviews basic background chemistry defining the observed fumes and attempts to correlate geology, blast design, and explosive composition effects on the level of nitrogen dioxide that can be observed in various blasting conditions. Additionally, a test setting for evaluating the generation of post blast fumes is presented with pertinent test data detailing generic explosive formulation modifications which effect the overall level of post detonation generation of nitrogen dioxide.

Jan 1, 1996

By Greg Mclellan, Mark Johnson, John Pepper

In this paper, the measured vibrations are plotted in terms of the individual PPV components versus Scaled Distance (SD) on logarithmic scales. The maximum PPV is pIotted on a separate graph and equations are presented to predict the maximum PPV based on sealed distance and prediction level usmg power fits. The prediction levels include a 99.9% curve, which encompasses the data points and provides an envelope formula for determining the maximum PPV at South Florida sites. The dominant frequency distribution is established for the PPV components.

Jan 1, 2001

By Rachel L. Bauer, Catherine E. Johnson

Explosive demolition involves first, the use of cutting charges to sever a column and second, kicker charges to move it out of alignment. Dynamite is the traditional explosive used in kicker charges as it is inexpensive, easy to initiate, and has a consistent track record of use. Dynamite, however, has health concerns in handling, fragmentation concerns from direct contact on the beam, and availability concerns due to being manufactured at only one location in the continental United States. Recently, water-cased kicker charges have been used in industry, and research has shown that a reduced dynamite mass is possible due to the added confinement, for energetic performance, and the incompressible fluid, which aids in the transfer of explosive energy into beam movement. This research will compare two different explosives, an emulsion (DYNO AP), and binary (HELIX), to dynamite for use in kicker charges, both with and without water-casing. Emulsion is commonly used in rock blasting to create a large push or throw due to its high gas volume production which could translate to kicker charge movement. HELIX is a binary explosive commonly used by the military in breaching charges with water backing. Experimental tests placed kicker charges at the base of a hanging steel column, modifying the ballistic mortar test used to determine explosive power. The study shows that water-casing effectively reduces air overpressure and enhances explosive performance. Among the tested explosives, HELIX showed the most substantial improvements with a 1.8 dB reduction in air overpressure and a 3.2 m/s (10.5 ft/s) increase in column velocity when water-cased. Dynamite and emulsion also benefited from water casing, with decreases in air overpressure (1.1 and 0.7 dB respectively) and increases in column velocity (1.1 and 0.7 m/s (3.6 and 2.3 ft/s) respectively). This research also shows that emulsion is a viable replacement for dynamite in demolition projects, performing similarly in both traditional use and water-cased charges.

Jan 21, 2025

By DuPont Magazine

RBH Note: as stated many times in these articles, frozen dynamite was one of the greatest hazards facing the blaster. It wasn’t until the late 1920s that it was solved for good, with the introduction of nitrated ethylene glycol as a partial replacement for nitroglycerin in dynamites. The du Pont low freezing dynamites contained TNT, DNT, or nitro-substitution compounds of various sorts.

Jan 1, 2015

By Gordon M. Matheson, Douglas A. Anderson, David K. Miller

"Traditionally, analysis of vibrations from blasting has been focused on peak particle velocity fordetermining the likelihood of both annoyance and damage. The US Bureau of Mines, in RI 8507,indicated the importance of frequency in vibration. Methods of controlling the vibration by reducingthe vibration concentrated in certain frequency bands using delays have been successful over the past decade."

Jan 1, 1997

By H G. Bosmare, G Bedser, C V. B Cunningham

Peak Quany has achieved substantial improvements to its bottom lie by giving close attention to blasting practice, and in pr@icnlar by introducing electronic delay detonators for routine production blasting. The precision and flexibility provided by these units has enabled the quarry to gain control over fmes and curtail oversize without increasing explosive usage. In addition, the extent of nuisance from blasting vibrations has been reduced.

Jan 1, 1998

By Ayman Tawadrous

Cave mining offers a flexible technique to exploit large, low grade, deep ore bodies with low operating costs. It is typically done in either a top down approach; i.e. sublevel caving, or in a bottom up approach; i.e. block or panel caving, to extract ore bodies that may have been previously considered unfeasible to mine. Sublevel Cave (SLC) mining, in particular, is a cave mining method based upon the utilization of gravity of blasted ore while the overlying host rock fractures and caves under induced stresses and gravity. Thereby the caved waste originating from the overlying rock mass fills the temporary void created by ore extraction to achieve a controlled collapse of the roof.

Jan 1, 2015

By Norman Paley, Finn Ouchterlony

Detailed fragmentation data for different blast delay timing tests at the Red Dog mine in Alaska are analyzed. This work is a continuation of previous work in which the crusher output was found to be better described by the three-parameter Swebrec function than by the Rosin-Rammler function. For a crusher model, the x50 variable sufficed to describe changing crusher input while b and xmax could be considered fixed. For the crusher output from aggregated stockpile rock, as measured by digital image analysis using Split-Online, the constancy of b was not as apparent. In this paper detailed stockpile data, single Split data series, and sieved belt cuts of crusher product are analyzed using the Swebrec and truncated Rosin-Rammler functions. The variability of b is confirmed. By using specific fraction passing sizes a shortcut is presented that removes the need to do curve fitting to determine the three Swebrec function parameters.

Jan 1, 2013

By John R. Holliday, William Marcum

Apogee Coal Company, DBA Arch of West Virginia, faced the challenge of drilling and blasting over one million cubic yards of high temperature overburden at its Ruffner surface operation near Logan, West Virginia. The overburden was removed above the Upper Five Block seam that was previously deep mined, abandoned, and later engulfed by fire. Borehole temperatures were measured above 700” F.

Jan 1, 1996

By Eduardo Lozano, Vilem Petr

This paper provides an overview of a new method for avalanche control using a high explosive charge placed at the avalanche runout zone: the case charge technique. This new avalanche control technique is well-suited to mountain roads presenting several advantages over the existing methods: minimum deployment time, low cost, reduced probability of misfires, and decreased operation time in the avalanche danger zone. The research work presented in this paper was conducted via large scale laboratory experiments where the detonation velocity and the blast physical properties were measured. During the charge design, several parameters were controlled: charge mass, diameter, geometry, density, and external confinement. In addition, the effective range of case charges was increased by the use of the Mach reflection for certain topographical situations. Finally, field test results collected by the Colorado Department of Transportation (CDOT) during the 2017 winter season are presented. The CDOT avalanche control crews have adopted the new case charge as the preferred technique in numerous avalanche locations along the Rocky Mountains roads.

Jan 1, 2018

By Shazad Hosein, William Birch, Douglas A. Anderson

This paper will present the results of tests of a new method for assessing explosive performance using wavelet transform analysis of standard blast seismograms. The theoretical background of the method was presented at an earlier ISEE conference.

Jan 1, 2015

By Sam Ammermann, William Heasley

"The mining industry is on an ever accelerating path to complete mechanization. As companiesutilize more sophisticated and efficient methods of blasting, a more thorough look should begiven to the pros and cons of mechanized shaft sinking. Historically, Vertical Shaft SinkingMachines (VSSM) have been capital intensive, making it hard to enter lowest bidder marketssuch as the United States. As advances in safety and technology have occurred, VSSM methodsare becoming increasingly common in many countries outside the United States. Decreasedcapital requirements, a greater amount of competition within the VSSM market along withgreatly improved safety practices, have made it more competitive with traditional drill and blast(D&B) methods. However, VSSM technology has yet to be embraced by the United States. Alarge culture shift will have to occur before VSSM technology will become common in theUnited States. The history, and advent, of raised boring machines will be discussed and how itrelates to the current development of VSSM technology. The researchers will analyze the uniquerisks of D&B methods and how they compare with the unique risks of VSSM technology. Theresearchers will put an emphasis on risks directly affecting the safety of personnel working onthe shaft sinking operation. Many of these risks are identified by contracting companies withregards to geology, relative location of resources and the chosen shaft sinking method. Theresearchers will discuss specific risks a given shaft sinking company will want to consider whenchoosing between D&B and VSSM methods."

Jan 1, 2016

By Dan L'Heureux, Joe Haid, Stephen H. Chung

Most coal deposits in Western Canada involve steeply dipping multiple seams. An efficient way to recover coal seams would be to drill through the seams and blast both the overlying and underlying waste material in one shot without disrupting the coal seams while fragmenting the waste rock for easy removal. This requires special blasting techniques as reported by Chung and Jorgenson in 1985.

Jan 1, 1998

By Paul Sainato

Recruiting and retaining students in the explosives industry is becoming increasingly important each year. With no undergraduate degree in explosives engineering currently available in the United States, it is from other industries and degree disciplines we must recruit. The 2014 annual ISEE conference saw the first anonymous online survey distributed to members of SEE student chapters of the International Society of Explosives Engineers. The survey contained questions about future job and career plans, ideal job placement, expectations of salary and current academic degrees. The purpose of the survey was to determine what these students expect or require from a career in the explosives industry, and their current path to pursue this. This information can help steer recruitment activities and job offers for graduating students. The success for both student response rates and interest from the industry has allowed space for a yearly update of this survey. A second survey was distributed in 2015 and included international students. This paper provides the data from a third online survey distributed to all student members of the International Society of Explosives Engineers, globally. Understanding the main incentives for a student to accept a graduate position as an explosives engineer can help us, as an industry; position ourselves to remain competitive in recruiting against other major degree disciplines.

Jan 1, 2016

By Evan Boone, Peter Bellairs

A technical services visit was conducted to determine the initial parameters to successfully presplit several benches for an input crusher installation at the Wolffdene quarry. The paper details the preliminary design utilising both detonating cord only and specialised presplit product charges and compares these to the final designs utilised based on site experience. The role of accurate drilling, explosive loading and geology in obtaining successful cost effective presplits is highlighted.

Jan 1, 1998