Search Documents

By Jason Baird, Philip Mulligan, Caleb Baumgart

This report details the pressure variances, measured at four pressure sensors placed equidistant from the center of an airburst explosion, as the blast pressure from a single charge expands radially. Many of the empirically derived equations used for predicting the blast pressures of an explosion, assume a point source detonation and that the radial pressure expansion is equal. The authors understand that the equations used to approximate the blast pressure may not have 100 percent agreement with the observed pressure. However, during previous research at Missouri University of Science and Technology (Missouri S&T) the pressure variances had a range of 1,200 psi, between the four pressure sensors placed two feet from the center of a 1/2-pound (226.8 gram) of hand packed C4. The variances indicated that at the close distance from a suspended explosive charge the pressure does not behave as that observed from a point source.

Jan 1, 2014

By S A. Steyn, P Terrett

Air decking has become a widely practised method internationally for modifying fragmentation results and providing cost savings from reduced explosive consumption. Duvha has been applying air deck technology to overburden and midburden blasting for a few years. A thorough evaluation of air decking at Duvha has been made by instrumenting a number of blasts and analysing costs from direct savings in reduced explosives costs to savings in improved dragline productivity.

Jan 1, 1995

In the office, on the wall to the right of my desk is a large map of the world. Some people stick pins in maps like this to show where they’ve been. If I did that my map would be a mess and look like a pin cushion. I was so fortunate to have been able to see how people live and blast in other parts of this beautiful planet. We l l , maybe some parts weren’t so beautiful and maybe some parts that were beautiful were hell holes for those living t h e re . Every time I re t u rn to the good old US of A, I say a small prayer in thanks for having been born and raised in a land of freedom and plenty. So many places and people have not been so blessed.

Jan 1, 2004

By P D. Katsabanis

"This chapter describes the principles for the derivation of the equations for a detonation wave.. Theimportance of the equation of state for the detonation products is demonstrated and commonly used equations of state are discussed. Furthermore a brief introduction to the TIGER code is presented."

Jan 1, 1992

By Roger Holmberg, Donald Jonson

The Swedish Standard SS 460 48 66, “Vibration and shock - guidance levels for blasting induced vibration limits”, is based on more than 50 years of experience from blasting close to structures and tunnels. The Swedish Standard gives a method for calculation of guidance values for different types of buildings and ground condition under the building. This is done for every building and structure within a predetermined zone. The guidance levels are for the peak particle velocity monitored in vertical direction. The standard is valid for all kinds of blasting project (tunnelling, quarrying, mining etc.) The guidance levels neither take in to consideration discomfort for people inside the building or structure nor vibration sensitive equipment inside the structure. The paper also presents the Swedish Standard SS 02521 “Vibration and shock - Blast induced airborne shock wave - Guidance levels for buildings”.

Jan 1, 2005

By Gary Kahn

The knowledge of how and when your explosives go off can help you make intelligent decisions regarding future application of explosives thus removing some of the black magic associated with blasting. The net result will be intelligently set-up shots with timing, explosive charges, and placement more accurately done. Lower operational costs can be achieved when the correct combinations are applied.

Jan 1, 1989

By M Ash, P Bellairs

The world class iron ore mines at Mt Whaleback, Tom Price and Paraburdoo located in the Hamersley Province of Western Australia must mine the Mt McRae Shale to obtain high grade ore from the Dales Gorge Member of the Brockman Iron Formation. The Mt McRae Shale contains a Black Pyritic Shale lithology that reacts with Ammonium Nitrate based explosives. This paper provides an overview of the problems associated with mining this reactive rock type as well as the development of a comprehensive procedure to safely and efficiently blast, excavate and dispose of this material.

Jan 1, 1995

By Qi Jinduo, Gong Min

On the basis of actual parameter of wall control blast in Nanfeng mine, China, the process of dynamic stress changing between two column charges was studied recently for a presplit-cushion blast by holographic photoelasticity. In the experimental model, two holes were simultaneously detonated from both ends (four ignition points). The bottom of the holes were loaded more than other parts (heavy charge). Under these conditions, four consecutive isochromatic fringe patterns at different times were acquired in one loading run, and the characteristics of the stress distributions were compared at different places and times in the holes. It was found that interaction types of stress waves vary along the holes. The theory is posed that the stress wave which is formed by the interaction of earlier producing P wave and later S wave along a distributed line charge is the most important part in all stress waves. Research indicates that a heavy charge in the bottom of the holes is crucial to producing a presplit-cushion effect at the bottom. "End Effect" doesn't affect the magnitude of stress along linking lines between the bottoms. The chief fields of the "End Effect" are also explained in the paper.

Jan 1, 1998

By John Yenter

"Unique blasting problems during reconstruction and expansion of 100 year old buildings toaccommodate gambling. Located on steep mountainous terrain and linked by narrowroadways, the towns of Central City and Black Hawk challenged blasters to exceptionalmeasures in order to control over_break, vibration, public exposure and damage to thecharacter of these historic mining towns. Utilities were also upgraded to fit demands of asmuch as 800% volume change in one year."

Jan 1, 1993

By Rundqvist

The best method to minimise disturbances from traffic to the neighbourhood and in Urban is probably to go underground. For obvious reasons this will cause vibrations, noise and other environmental effects which need very strict regulations and quality assurance in order to complete the work successfully. One project is “Southern Link”, a part of a ring road system. The system of tunnels includes 16 kilometres of tunnels right beneath the south part of the city of Stockholm. At least 20.000 people will be or could be affected by different kinds of disturbances and pollution such as vibrations, noise, gas and groundwater. Another project is the “Arlanda Link”. A new railway with three stations has been built under the existing and running to Arlanda airport with its terminals. Authorities have carefully judged these projects, which cause complaints from neighbours due to disturbances. The blasting operations are professionally managed by the contractors and controlled by consultants to keep the regulations according to the Swedish standards, which are well described in the tender documents by risk analysis and technical descriptions. In spite of that, one conclusion is that it is not always possible to go underground without exceeding stipulated regulations with existing technique. Some of the regulations also double the cost of excavation

Jan 1, 2001

By A. Karadogan, G. Tuncer, A. Kahriman, S. Gorgun

This paper presents the results of ground vibration measurements induced by blasting operations at five different sites located close to the residential areas. Within the scope of this study, ground vibration components were measured for all blast events over a long period of time in order to predict peak particle velocity and determine the slope of the attenuation curve for five sites. During the study, while the parameters of scaled distance were being recorded carefully, suitable monitors for all blast events of five blasting sites measured the ground vibration components. At the end of evaluation of the data pairs, an empirical relation, which gives an average line at 95% confidence level, and upper bound 95% prediction line with a good correlation coefficient was established and suggested for each site

Jan 1, 2003

By David Ziegler

A formal blast plan is sometimes required for projects involving rock excavation. A written blast plan submitted with a bid proposal can also be an important sales tool. A blast plan will cover the basic elements of shot design: hole diameter, spacing, burden, loading, and so forth. Some suggestions are discussed here for additional items or topics to address, including: safety issues, ground control, traffic & site control, public relations, pre-blast inspections, seismic monitoring.

Jan 1, 2003

By Ed Clah, Catherine Aimone-Martin

The vibration response of a 30 in. diameter high-pressure (845 psi) natural gas pipeline to 11 coal mine blasts was measured. The X-52 steel pipeline was buried 7 ft. below the ground surface. Ground and pipeline motions in terms of velocities were recorded on the pipeline, in the ground adjacent to the pipeline, and near the ground surface directly above the pipeline. These data were used to estimate the maximum stresses and strains in the pipeline occurring during the blasts. Pipeline standoff distances varied from 264 ft. to 3720 ft. Two blast hole layouts and timing schemes were used. One represented highly confined blasts to limit movement of the shot overburden that generated high ground motions at the pipeline. The second represented patterns that provided greater relief and lower the ground velocities at the pipeline.

Jan 1, 2003

By Jerald E. Harris

"Often taken for granted, drill accuracy plays a major role in the relative success or failure of a blast.Expensive technological advances in equipment capabilities, drilling tools, communications, explosives, and timing can quickly be nullified by poor drilling."

Jan 1, 1999

By Larry R. Fletcher

A misfire results when explosives fail to detonate as planned during a mine blast. Accidental detonation of misfires is a frequent cause of personal injury, equipment damage, and lost production. In an effort to minimize these problems, the Bureau of Mines investigated the causes of misfires, methods for detecting misfires, and procedures for their disposal. During this investigation, input was obtained from explosives suppliers, mining companies, blasting contractors, blasting consultants, and governmental agencies. Additional data were obtained through detailed analysis of blasting accidents involving misfires.

Jan 1, 1983

By Joseph Haid, om, Rio Yang, Kelly Fleetwood

Some coal mining operations in the Powder River Basin are currently observing a number of blast holes detonating sympathetically within their cast blasts. Sympathetic detonation can cause poor cast results, high blast vibration levels, excessive back break and fly rock, along with a number of other undesirable blast results. The reduction or the total elimination of blast hole sympathetic detonation is of paramount importance to the coal mining companies operating in the Powder River Basin. This paper describes a systematic approach to prevent cast blast holes from detonating sympathetically through the use of the electronic initiation and expanded blast patterns. In-situ measurements outlined in this paper were recorded from pressure probes, velocity of detonation probes and near field accelerometers, along with digital images generated from a high speed CCD camera. Large diameter angled drill holes were also checked for any measurable amount of deviation by a cable type borehole measurement tool. The field measurements provided the scientific evidence, statistical data, and documentation necessary to develop a sound method or a “road map” that would minimize and in some situations prevent the occurrence of blast hole sympathetic detonation.

Jan 1, 2005

By Jack Eloranta

To improve control of blasting, tests were performed to assess non-electric cap accuracy. Simultaneous testing using a Velocity of Detonation Recorder (VODR), Red Lake Lo-Cam and an Instantel DS-677 blast monitor was done. Favorable comparisons were found in the three records . This testing confirmed the accuracy of an inexpensive and expedient cap testing procedure.

Jan 1, 1992

By Rob Farnfield, Yuill Gavin

The rock blasting industry continues to be under pressure to reduce the level of vibration induced by the use of explosives. In recent years much research and development has been directed to minimizing vibration levels by controlling the delay period between blast holes. The most commonly applied technique is known as Linear Superposition. This technique takes the vibration produced from a single-hole test shot and simulates the vibration that would be produced from a full-scale production blast. The simulation can be run with various delay periods and the optimum delay chosen. The success of the Linear Superposition technique depends to a great extent on having accurate delay detonators and on the single-hole test shot reliably indicating the vibration signal produced from each hole in a production blast. A quarry-based case study is given illustrating how these assumptions are not always valid. In this case the use of electronic detonators has controlled frequency but not vibration level. The paper goes on to describe a series of single-hole test shots in an U.K. limestone quarry. The vibration 2 signals recorded are examined in terms of variations in free-face provision, blast geometry, explosive properties, etc.

Jan 1, 2001

By Lance McAnuff

The year 2001 coincided with the forty-fifth year of blasting-control specialization by the author. Commencing with the construction of the Saint Lawrence Seaway System in 1956 and continuing until the present time this career has spanned one of the most progressive and exciting periods in the still relatively short history of commercial blasting. The paper touches upon a number of the more interesting projects with which the writer was involved during those early days, including the removal by explosives of “Ripple Rock” the infamous underwater hazard to shipping which at one time inhibited ocean traffic along the Inside Passage between Vancouver Island and the mainland of British Columbia, Canada’s most westerly province. Various assignments involving incidents from devastatingly ,tragic to comically absurd are described, along with personalities encountered along the away, most of them readily recognizable as giants in the field of explosives engineering. Various stages in the evolution of state-of-the-art explosive products, initiation systems vibration monitoring equipment and limiting criteria are compared and some of the effects these have had on safety and productivity during the last forty-five years are analyzed.

Jan 1, 2002

By W. J. Birch, M. Kirke

Despite increasing competition from mechanical methods of tunnelling, the drill and blast method is often still the most viable method of excavating tunnels in strong and abrasive rock. To advance a tunnel using drill and blast, explosives are loaded into boreholes in the rock and detonated according to a prearranged sequence. On detonation of the explosive, the rock is fractured and displaced from its original position, leaving behind the desired void. Among the secondary effects of a tunnel blast are ground vibrations caused by elastic disturbances that propagate away from the blasted tunnel face. The possibility that such ground vibrations may cause permanent damage to property and substantial nuisance has generated significant opposition to the use of drill and blast, particularly in urban areas. It is therefore essential that the blasting engineer is able to predict Peak Particle Velocity (PPV) vibration levels at locations in the vicinity of the blast site. Such predictive capability enables the engineer to design blasts so as to ensure that ground vibrations can be kept within acceptable levels. The objective of this project was to analyse data obtained from the ground vibration monitoring program undertaken during the drill and blast excavation of a hard rock tunnel in Central England. Seismograph recordings of tunnel blasts contain a vast amount of information that cannot possibly be expressed using a single PPV value. The main focus of the study was to investigate whether predictive capability could be improved by using scaled distance models derived for selected PPV components relating to specific detonator timings in a given tunnel round. This study has established a method of analysis that can unlock this information for predictive purposes. By permitting the extraction of sub-event Peak Particle Velocity (PPV) values and allowing Scaled Distance (SD) models to be derived for individual period numbers or groups of period numbers, the method has the potential to vastly improve PPV prediction from tunnel blasting. The method established could also help diagnose blasting problems and help target blast design modifications, resulting in improved efficiency and excavation rates.

Jan 1, 2005