Search Documents

By Greg Shapiro, Paul Dr. Worsey

Mining, quarry, and construction blasts are becoming more and more dependent on bench profiling. The use of accurate profiling gives the blaster better data for the most efficient blast results. So, we ask the question: What is the best method for measuring and analyzing burden?

Jan 1, 2019

By Clay McNail, Paul N. Worsey, John Schillie

"This paper is the result of undergraduate student research over the period of 2 semesters at UMR, which was focussed on developing a practical way to pneumatically stem horizontal boreholes, mostcommonly used underground. The majority of dry horizontal underground boreholes are pneumatically loaded with bulk ANFO. ANFO is preferred due to its low cost and the ease of pneumatic loading. However, stemming underground in the United States is a rare practice. In sharp contrast, stemming material (crushed stone or drill cuttings) is virtually always used in surface holes. The purpose of stemming is to increase blast efficiency by containing the explosive energy in the ground and to reduce environmental effects such as air-blast. The problem with stemming horizontal boreholes are; gravity cannot be used to load stemming material and the ANFO does not have a good interface due to problems with withdrawing the hose and the loading itself. This work follows on from Wilkins’ work on stemming angled boreholes."

Jan 1, 1999

By Rick Lamkie

When investigating citizen complaints about blast vibration and airblast, it is important to be able to establish the spatial relationships between blasts, blasting seismographs monitoring the events, and complainant structures to assess any directional impacts. The Pennsylvania Department of Environmental Protection (DEP) routinely uses hand-held GPS receivers to document these relationships. The waypoint (structures and seismograph monitoring locations) and tracking (blasting and permit areas) features are used to map a site. These data are imported into the software for editing and conversion to GPS Exchange (.gpx) format.

Jan 1, 2008

By Thierry Bernard

New technology to automatically design a blast based on autonomous drone. The process of flying a drone, calculating the 3D cloud of points, generating the critical face profiles and placing holes automatically according to burden specification becomes fully automatic. A nice time saving with more efficiency

Feb 1, 2020

By Charles Dowding, Cathrine Aimone-Martin

This article summarizes an investigation of the structural response of a brick façade home in New Mexico. The subject Ricter residence was located some 1100 to 1400 ft away from an aggregate quarry, and was subjected to a maximum peak particle velocity and air blast over pressure of 0.29 ips and 122 dB, respectively. Superstructure (corner) and mid-wall responses to blasting and human induced activities were measured. An existing exterior crack in the brick work was instrumented to measure crack width response to blasting, human induced activities, and environmentally induced changes in temperature and humidity. Crack and structure response data were correlated with ground velocity and airblast excitations. Amplification of ground motions at the upper structure were calculated and compared with values for typical wood frame structures. The natural frequency and damping characteristics of the structure were determined to compare with measured amplification values. Wall strains produced by bending and inplane tension strains were computed from upper corner structure response and compared to failure strains for drywall and brick veneer. Calculated strains were found to be far lower than those required to crack brick and environmentally induced crack response was found to be far greater than that caused by blast induced ground motion or airblast overpressures

Jan 1, 2005

By Muamer Medusalic, Kim Henley, Lucas Bottomley

The period from 2009 to 2012 has witnessed a large rise in the number of blast-generated fume events in Eastern Australia, where highly visible oxides of nitrogen (NOx) are produced from coal mine blasting. Fume production mechanisms have been poorly understood by mine operators, and practical measures to reduce fume were initially elusive. Over time, data on fume events has been collected and analysis has pointed to a range of contributing factors associated with fume production.

Jan 1, 2012

By Michael S. Wieland

"This report investigates whether it is tractable and thereupon reasonable to remove the boosterinfluences when ranking the toxic fumes of non-cap-sensitive mining explosives. The hazard potential is represented by relative fume toxicity RFT, the resultant influence computed from a formulated rule with a restricted set (tally) of fume components and multiplying constants. The RFT result is compared to the rule criterion that represents the worst case tolerable toxicity stipulated by regulations or otherwise. The typical nonstoichiometric booster composition can render notable unwanted influence on the RFT ranking results. Historically, the remedy was to shoot the booster separately and reduce the trial concentrations by the relevant subtractions. Unreal negative concentration results were noted on rare occasions, revealing the faulty nature of the reduction procedure. With thermodynamic reaction chemistry codes TDRC, on the other hand, the booster ingredients can be retained in or removed from the reactant tabulation, yielding reduction factors taken as the concentration ratios for the two circumstances. The underlying presumption regarding reduction factors is that the ratios of component concentrations with and without the booster ingredients when resolved theoretically ought to equal those rendered experimentally, when tractable. Upon rearranging the presumed relationship, the unadjusted fume concentrations divided by theoretical reduction factors yield the wanted readjusted fume concentrations, thereby removing the booster influence without generating unreal negative concentrations."

Jan 1, 1999

By Norm Disley, Kingsley Hortin, Gertjan Bekkers

As part of the expansion of the Kidd Creek Mine to 2,682 meters (8800 feet) below surface, two largediameter 3000kW (4000HP) booster fans were installed at the 6000 level. Shortly after commissioning the fans, significant damage to the fan bearings were observed, forcing several shutdowns for repairs, which were very disruptive to the mine’s production process.

Jan 1, 2008

By Richard J. Mainiero, Harry C. Verakis, John J. Mulhern

There are application in coal mines where it would be advantageous from a safety stand point to fire unconfined shots. However, the firing of mud caps (adobes) or other unconfined explosive charges in underground coal mines is not permitted because of the explosion hazards associated with methane gas and coal dust. Present safety regulations in Title 30, Code of Federal Regulations prohibit such Practices. Recently, MSHA proposed revised coal mine regulations for the approval and use of sheathed explosives for Public comment.

Jan 1, 1987

By Jorge Flores, Benjamin Cebrian

Blast Optimization at a high altitude mine operation involves not only the selection of the right drilling designs and explosives but also the circumstances of operators working at low oxygen levels and low temperatures.

Jan 1, 2015

By Cameron McKenzie, John Heilig, Patrick Andrieux, Andree Drolet

It is widely accepted that both underground and surface blasting operations can de-stabilise excavations to the point where it can threaten the feasibility of mining through personnel safety or OK dilution. Research has been undertaken to outline a practical method in which the impact of blasting will be accounted for during the early excavation design stage by modelling, and during the following production stages by monitoring rock response to blasting operations.

Jan 1, 1994

By Stephan Iversan, Janae Singer

High resolution seismic refraction tomography has proved to be a useful tool to effectively estimate depth of blast induced damage in rock. Excavation blast damage can be as shallow as 1 to 2m (3 to 7ft) and requires resolution at a fraction of a meter for effective imaging. We used an accelerometer with flat frequency response to 1000Hz to record data at spacings of approximately 0.25 to 0.5m (0.8 to 1.6ft) along mine walls. The resulting tomograms of P-wave velocity show low velocity zones which we interpret as residual fracturing from blasting. Experiments on a concrete test block and at two underground mine locations give results that are consistent with fractured rock transitioning to competent rock.

Jan 1, 2009

By C F. Argo

In the past several years the "Kelly Bar", an innovative device, which incorporates borehole d-rifling and explosives loading into a single detail, has come under scrutiny and criticism. The practical aspects of the Kelly Bar procedure is not questioned, and the system has been highly successful in expediting the loading of explosives in difficult and unstable formations. There have been a number of accidents indirectly associated with Kelly Bar loading and the point in question has become one of safety rather than mechanical feasibility.

Jan 1, 1975

By Scott Stephenson

Making a tunnel through solid rock can sometimes be a dangerous task. Many things must be considered in order to complete such a task safely, and efficiently. Prior to starting things must be known such as, the type of rock, the purpose for the tunnel, the destination point, then angle of decent (or ascent). Once these things are known, the method to proceed must be considered. Factors such as cost, feasibility, and time to completion must be taken into account.

Jan 1, 2009

By Carlos Campos Junior, Leonardo Soares Chaves, Raul Carretero Hoz, Renato Jacome Costa, Davi Bastos Martins de Oliveira

The Vale’s Serra Sul mine, also known as S11D project, is one of the world’s largest open pit iron ore mines, located in Brazil’s Amazon region. The mine produces around 90 Mt of high-quality iron ore annually. Its unique orebody enabled the S11D project to adopt a truckless mining system with In-Pit Crushing and Conveying (IPCCs) for ore exploitation and waste stripping. The IPCCs system requires crushing the waste, mainly composed by the jaspilite lithology, and is also conveyed to waste deposits several kilometers away from the mine. Due to Amazon’s environmental restrictions, the project was designed with preliminary geological knowledge, leading to the installation of primary crushers not designed for the hardest jaspilite, with uniaxial compressive strength (UCS) up to 500 MPa. This resulted in low waste crushing performance, affecting stripping ratio and threatening future production. A project was developed to improve the fragmentation of the jaspilite, allowing higher waste IPCC production, and reducing the risk to the production due to low performance of waste crushing and conveying. The first challenge was the independence of the geological and the geomechanical models, while only the geological model was considered in blast designs, the geomechanical model describes six waste groups of jaspilite classified according to their strength. A new geological model was then created to incorporate the geomechanical classification, allowing different blasting design according to the rock strength of the jaspilite. The blasting pattern on most compact jaspilite was reduced 27%, from 22m² to 16m² in 9 7/8” diameter holes, with a proposed theoretical reduction of 23% of the P80, from 326mm to 250mm. The second challenge was the implementation of the new design, as this pattern size and the high powder factor (2.9 kg/m3) were paradigms for such a large iron ore mine. The measured results have shown 25% reduction of the P80, the crushing rate was increased by 17% (230t/h), saving around $2.4 million annually in crushing and conveying system maintenance.

Jan 21, 2025

By Dennis Alan Clark

An increase in construction and quarry operations has necessitated blasting activities in areas once considered rural and in the close proximity of transmission pipelines. A method to determine the maximum allowable bending stress by the formulas outlined by the Battelle Memorial Institute report of October, 1962, and the assumed stress comparison with actual measured data is presented. A direct relationship between pipe stress and ground particle velocity is shown, and a method to predict stress by relating stress to charge weight and distance from the shot point is discussed.

Jan 1, 1976

By Earl Cook

With all our power and hope, we are part of the natural system and subject to its laws. As Francis Bacon pointed out long ago, we must understand those laws and "obey" them if we wish to "conquer nature." Bacon was saying that if we plan and engineer in compliance with nature's laws, we'll get a lot more out of the natural system than if we don't, because then we can use the system instead of fighting it.

Jan 1, 1979

In this paper, the author points out the need to beware of simple time correlations as proof of cause and effect when comparing building cracks and blasting operations. There is a need to be aware of the many other causes besides blasting which affect buildings. Some of these have histories of cyclic behavior; others have a long-term increasing effect on aging and deterioration, often with poorly defined time histories. Many are so strongly site specific that generic relationships are difficult to quantify.

Jan 1, 1981

By John W. Kopp

The U. S. Bureau of Mines investigated flyrock and burden movement from blasting at several limestone and basalt quarries in the upper midwest. Blasts have been studied at 14 different sites using high-speed cinematography. Blasting was accomplished in 75- and 150-mmdiameter holes using a variety of explosives. Films from each blast were analyzed to show burden velocities, observed flyrock distance, and direction of throw in relation to the shot layout. This technique, in some cases, allowed determining point of origin and cause of the flyrock as well as the flyrock range.

Jan 1, 1994

Prepare ATF Report of Theft or Loss (ATF Form 5400.5). A Report of Theft or Loss - Explosives Materials must be prepared when it is discovered that explosive materials are missing from inventory. Submit the original to the U.S. Bomb Data Center and keep a copy for your records. The form can be obtained from the ATF Distribution Center or from www.atf.gov. Although the U.S. Bomb Data Center should be notified as soon as possible, Federal law requires notification within 24 hours of the discovery. A full inventory check is also highly recommended (but not required) to locate missing explosives and to prevent future losses.

Jan 1, 2008