Search Documents

By Hideaki Kitajima, Ryo Sakamoto, Katsuya Sasaki, Maehata Hidehiko

The Electric Discharge Impulse Crushing System (EDICS) is a technology for carrying out crushing by using electrical power and nitromethane. It is designed for construction tasks such as splitting of concrete and rocks.The EDICS consists of an electric discharge generator that supplies a high-voltage high-current pulse, a cartridge that generates power by using electric discharge energy, and cables that connect the electric discharge generator and the cartridge. The cartridge contains a thin metal wire that evaporates because of the electric discharge energy and a nitromethane that reacts with this evaporated metal wire. The cartridge can be used to generate a high pressure on the order of gigapascals within a time interval of several hundred microseconds, and crushing power equivalent to that generated by explosives is generated during this period. In recent years, the EDICS has been widely used in Japan because of its good performance and favorable characteristics.

Jan 1, 2011

By Midori Sakamoto, Nobuaki Sakuma, Tsuyoshi Murashita

Recently, tunnel blasting works near the residential area and existing building are increasing and environmental problems caused by vibration have become serious public concern. In order to solve these problems, blasting works have been conducted with segmented blasting and reduce advance per round. However, with these blasting, work efficiency is not obtained, and regrettably the cost and risk of accident tend to increase. We developed a new controlled tunnel blasting technique with electronic delay detonator. Electronic delay detonator can supply extremely large range of delay period which could not be achieved with conventional pyrotechnical delay detonators. We utilized advantages in initiating hole by hole over entire tunnel face at the same round. Much seismic data obtained from tunnel blasting with conventional detonator was statistically analyzed in order to find average duration time of vibration caused by a single hole initiation. Numerical simulation using sample waves from a single hole initiation was carried out in order to find an optimum delay time which can separate vibration in each hole initiation and without decreasing blast performance. Trial blasting was conducted to examine the correctness of optimum delay time obtained from numerical simulation. This blasting technique was applied to an actual tunnel construction. This tunnel is 2 lane automobile tunnel with a total length of 659 meters and internal cross section of 70 square meters. The purpose of the use of blasting technique on occasion, was the protection of fresh water reservoirs directly above the tunnel, and to keep the effect on local private houses to a minimum. The vibration level against this station was limited under 20 mm/see P.V.V. With this blasting, the tunnel construction was completed without exceeding the limited vibration level, with minimum cost and construction time.

Jan 1, 1998

By Francisco Leite, Tomi Kouvonen, Bianca Saraiva, Vinicius Miranda, Auã Oliveira

One of the main challenges facing mining engineers is to draw up a plan that can be implemented in a timely manner, taking into account the operational variability of the mine’s production processes. These plans are often drawn up based on deterministic modelling (provided there are a set of known inputs that will result in a single set of outputs), when in truth we are talking about stochastic events (the cycles involved behave like random variables and their nature may be studied and reproduced). The result of using this kind of methodology can lead to non-optimized intuitive choices, which may harm the long-term targets defined by the planning team. Based on this principle, this document investigates the simulation of the rock fragmentation process in an open pit mine to assess the stochastic behavior of the loading and haulage operating cycles. The data assessed by the simulation process were the total costs of these operations in function of the powder factor. Based on a sample set data items, it was possible to check the probability distribution of the event as a Poisson distribution, applied to the loading and haulage cycles. The simulation consists of the repeated sequenced reproduction of these events (Monte Carlo simulation), in order to find the configuration that best fits the loading and haulage operations. By integrating these systems, it was possible to better understand the influence of the blasting in these operations, and as such to reduce the associated costs.

Feb 6, 2023

By John Wright

As part of the redevelopment of the Royal Brisbane Hospital complex in Australia, a number of antiquated buildings were to be demolished and replaced by newer, modem facilities. Aside from the decommissioning of the hospital buildings, the project called for the removal of approximateIy 24,000 bank cubic metres (bcm) of varying quality rock material. Given the sensitivity of the project, in particular the close proximity of the required excavation to the existing hospital structures (-3 metres at the closest point), and the requirement that these were to remain lily operational during the construction phase, it was initially proposed to use hydraulic rock hammers as the primary means of excavation. Poor production rates and unexpected dif3icuIt rock conditions led to a revision of the excavation methods and a feasibility study on drill and blast practices was undertaken. Subsequent to an initial series of trial blasts to illustrate that vibration and flyrock could be adequately controlled, drill and blast methods were used in conjunction with mechanical methods of rock breakage. This paper reviews the drU and blast processes and the practices which were necessary to comply with the multiple constraints imposed on the project. The project has highlighted that modified drill and blast practices remain a cost-effective method of excavation, even in sensitive areas which are commonly deemed inappropriate for such methods.

Jan 1, 2000

By P D. Katsabanis, L Liu

Numerical modelling of fragmentation and throw is used to provide information on practical blast design parameters. The function of airdecking and its practical implications, the importance of the initiation point and aspect ratio of cratering charges and the timing between adjacent blastholes are investigated. Accuracy requirements for detonators are discussed with emphasis placed on the volume and fragmentation of the blasted rock, and compared to experimental results. Practical guidelines which have been based on intuition are examined using the model. Some of the predictions have been tested and correlate well with experimental results, obtained in the laboratory. Findings show that a minimum airdeck length is needed to realize any benefit from the application of airdecking in production blasting while the process can enhance the shock energy provided by non-ideal explosives significantly, bottom initiation of charges is beneficial to fragmentation and the aspect ratio for cratering charges can exceed the traditionally accepted ratio of 6. Regarding timing, in the ease of cratering charges, true simultaneous initiation shows beneficial results for the volume of blasted rock; however the accuracy required for practical detonators is very high. Fragmentation improves after a certain delay time while the optimum can be achieved at a range of delays. Timing affects muckpile shape; however it appears that subtle differences in delay times do not have a significant effect.

Jan 1, 1997

By Joe Atalla, Leojenen Etulle, Jesse Desrochers, Joseph Mukendi Kabuya, Remi Proulx, Ruilin Yang

The Mont-Wright mine is Canada's largest open-pit iron ore mine with multiple open pits in operation. It is operated by ArcelorMittal Mining Canada in the northeast of the province of Quebec, near the town of Fermont. Fragmentation of rocks with explosives generates vibrations and gas expansion that damage intact rocks, affect existing crack networks, reduce the shear strength of discontinuities and the quality of the rock mass of the highwalls. The efficiency of its blasting operations is challenged by the need to optimize production and manage the risk of mine slope instability caused by vibrations from successive blasts. This paper presents a Multiple Seed Waveform (MSW) vibration model that was established at the mine for this purpose. Near-field signature hole blast vibration monitoring was conducted in multiple areas to establish site characterization as input to the blast vibration modeling at the highwalls of the site. The vibration attenuation laws were established and the effects of different blasthole diameters, shifting frequencies and presplit design were evaluated. Based on the results obtained from the near-field blast vibration monitoring, the calibrated MSW vibration model was used to select blast design parameters to control blast vibration while maximizing productivity of blasts at Mont-Wright mine.

Jan 26, 2026

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson, Brian Somes

"To perform a probabilistic risk assessment (PRA), a method of quantifying the risks associated withinfrequent, high consequence events, consequence models that generate representative estimates of human health consequences for a wide variety of representative scenarios are commonly used. Criteria that suitable models must possess include: (1) input requirements necessary to generate large volumes ofprobabilistic simulations; (2) the capability to output injuries with the necessary details and resolution;(3) the ability to capture the variety of different scenarios inherent in an assessment; (4) acceptablecomputational requirements; and (5) sufficient stakeholder buy-in for community acceptance."

Jan 1, 2017

By Robert Hopler

SECTION 9.---BORING AND BLASTING.*155. Blasting is the operation of bringing down and detaching from its bed or position masses of material by means of explosives.

Jan 1, 2011

By Michael Wieland

The work principle from thermodynamics is used to model the shock and heave for explosives shot in rock or under water, with the latter compared to reported results. The work principle utilizes restrictions and constraints to yield a representative fit to the irreversible (natural) shooting process. The reduction of the internal energy of the reaction-zone yields the total expansion work (TXW), the resultant sum of the rock/water shock and heave. The restoration technique of forming a closed thermodynamic loop yields the reversible mechanical work (RMW) or the rock/water heave. The residual work that remains when RMW is subtracted from TXW yields the irreversible disorder work (IDW) or the un-dissipated (without loss) shock in the surrounding rock or water. The work principle renders an unequivocal relationship for the shock-loss factor, rather than the traditional roundabout formula for correcting the underwater gauge-shock of un-modeled explosives. There’s a novel heave-ratio factor that unquestionably rates the fit of results under comparison. Rock-shots are more complex in nature than underwater shots due to rock fracture and stratum rupture, though numerical resolution is worthwhile. The proposed rock-water-jelly (RWJ) model yields rough estimates, with rock-type results not wholly different from their underwater counterparts. Though reported underwater shots reveal shock and heave trends with respect to charge formulation ingredients, there are no such rock-shot results for comparison, since the relevant test measurements in rock remain difficult, if not intractable.

Jan 1, 2007

By Alejandro Ferrada Vergara, María Jesús Barros Godoy

The need for a basic method for selecting explosives based on rock mass or intact rock properties for mining and construction arises from the limited consideration given to these factors when choosing among products and also an implicit overestimation of the explosive power to fragment the rock. This study highlights the importance of evaluating different properties such as rock strength, deformation, fracturing, detonation velocity and energy release when selecting explosives. The concept of characteristic impedance, which considers rock strength against shock waves generated by explosive detonation, is introduced. Understanding this concept is crucial for assessing explosive behavior according to various rock types. The study concludes with a practical guide table that categorizes rock properties and provides recommendations for selecting explosives based on rock mass and rock properties. However, it is important to consider other relevant factors, such as the presence of water or nearby instabilities, which can influence the final choice of explosives.

Jan 21, 2025

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson

"The United States (U.S.) Department of Homeland Security (DHS) Directorate of Science and Technology (S&T), utilizes a probabilistic risk assessment (PRA) approach to explore the risks (anduncertainty) from chemical, biological, radiological and nuclear (CBRN) threat agents to the Homeland.This end-to-end risk methodology considers a broad range of hazards incorporating emergingtechnologies, available countermeasures and input from the Intelligence and Law Enforcementcommunities (IC/LE) to evaluate the acute risk to human health due to an attack on the U.S. homeland. The PRA generated output provides a mechanism to examine risk mitigation strategies, critical vulnerabilities, critical data and knowledge gaps and relative risk rankings of materials, targets, classes of compounds and scenarios."

Jan 1, 2017

By A. Torrance

A better understanding of the detonation performance of an explosive charge can be gained by directly measuring pressure, temperature and velocity of detonation (VOD). This is particularly important with commercial explosives because their performance is directly influenced by the degree of confinement given by the borehole diameter and the surrounding rock mass. A project funded by the Australian Coal Association Research Program (ACARP) was initiated in early 2009 with the view to design and build cost effective prototype instrumentation to measure the relative differences in detonation pressures and temperatures of commercial mining explosives. The project’s primary focus was on low density explosives. Low density (also referred to as low shock) explosives have been available in various forms for nearly 20 years. Identifying the pressure release patterns of both conventional and low density explosives under different geotechnical conditions should provide the necessary information to both validate detonation codes and better define input parameters for breakage and fragmentation models. This paper gives a general description of the prototype instrumentation developed and reports on the results obtained to date in testing the proposed instrumentation in laboratory scale conditions.

Jan 1, 2011

By Tie-jun Tao, Ming-sheng Zhao, En-an Chi

"Karst landform is a special kind of geomorphic unit which is often accompanied by a large number of geological defects: caves. In blasting engineering, if there are karst caves around the blast-holes, it may result in higher boulder yield and the generation of flying rocks due to the change of burden which is very hazardous for the safety of surroundings. The models of rocks with karst caves from blasting holewere built by the software of ANSYS/LS-DYNA. The results of computation simulation show that thecave can increase more free surface for blasting and leads to a broken zone around itself. Thus rockmass around the cave will fly toward inside and it will result in undesirable result of whole rock mass to be blasted. In addition, the models of rocks with karst caves in different shapes were simulated and thecomputation results show that the caves in round shape have higher load resistance capability than that the caves in rectangle shape. All the simulation results can offer effective guidance for blasting design. The models of rocks with karst caves were built in different distances and shapes from blasting hole by the software of ANSYS/LS-DYNA. The effect of different karst caves on blasting stress and blastingresult were studied."

Jan 1, 2017

By Calvin Konya, Anthony Konya

Presplitting is a form of blasting that when executed properly will create a smooth wall that will minimize secondary conditioning. In recent years, presplitting has become a popular technique to be used in both the mining and construction industries, however, presplitting fails on many occasions because of ‘geologic conditions’. This is typically because of improper explosive loads consisting of overloading and underloading blastholes. In this paper the authors introduce new factors such as a presplit factor which varies for different rock types, selection criteria for the spacing of presplits, and the optimization of explosive load for the technique of Precision Presplitting.

Jan 1, 2017

By Dr. Bronwynne Victor, Quentin Steyl, D. Scott Scovira

Bulk emulsions and emulsion blends may be formulated with a single salt, dual salts, or multiple salts. Blasting professionals familiar with single salt ammonium nitrate emulsion products may be less acquainted with dual and multiple salt emulsion products that may include calcium nitrate, sodium nitrate, and urea in their formulations.

Feb 1, 2020

By G. Walsh, L. Wolkovitch, A. Savage, V. Romero, T. Zimmerly, G. Imahara, J. Hyneman, K. Byron, D Tapster, S. Belleci, J. Metzger, M. Stanley

Testing was conducted at the Energetic Materials Research and Testing Center for the MythBusters on three separate occasions. This testing included (1) an experiment designed to create diamond from graphite using the shock and pressure of a detonation, (2) the flattening of a car using a steel plate driven by a rocket sled, and (3) the bifurcation of a car also using a rocket sled. All tests were successful; diamond was produced following the detonation of ANFO, and extracted from a graphite / cobalt matrix. A plate was accelerated to 646 mph (1040 km/hr) using a two-stage sled system loaded with 5” (12.7 cm) high velocity aircraft rockets (HVAR) into a car, which was subsequently demolished. Finally, a steel wedge was pushed to 541 mph (871 km/hr) by a one stage sled using HVAR rockets, and was able to cleanly cut a target car in half.

Jan 1, 2010

By Shonn K. McNeill, Joshua Micah Hoffman

Security engineering is similar to other forms of engineering – the design is guided by the loads, materials, and desired function. For facility design, the load is the threat. Facilities that are designed with considerations for explosive hazards are designed with a shot, or series of shots, of a given size and distance from key locations. These facilities range from office buildings and industrial sites in developed nations to military and police stations in contingency areas. The challenge is the design shots are not often communicated to facility owners and managers. If the hazards change, whether it’s due to an increased capacity to cause damage by a threat or a decrease in capacity by a structure, not knowing the design shot means not knowing if security design needs to change. Blast modeling is an engineering tool that can be used to reverse engineer what a facility is suitable for, as well as be a tool for modifying security design for new conditions. This paper will examine military and civilian examples, including a case study of a military facility that did not know their as-built conditions and had to be rapidly closed; due to the determination their security engineering shortcomings could not be mitigated.

Jan 1, 2019

By Unknown

[Executive Director’s note: According to 17th edition of the ISEE Blasters Handbook in its section on trench blasting, “...consideration must be given to the proper venting of gases generated from the blasting. Should those gases spread laterally rather than vent directly to the surface, the gases may travel underground and finally vent well outside of the planned area. Such events may be caused by the strata, soil conditions or root systems, or existing and/or abandoned utilities or other man-made structures. In the worst situation, gases resulting from the detonation such as CO2, CO, and/or NOx may travel through the strata and find their way into basements of nearby homes or businesses. The IME has recommendations on how to minimize this potential problem. Some of the points include removing the overburden and digging the rock immediately after the shot, and drilling vent holes periodically between the ditch and adjacent homes.” The Board of Directors of the International Society of Explosives Engineers has expressed its concern that blasters be made aware of the issue of migration of carbon monoxide resulting from blasting operations. What follows are excerpts from “Carbon Monoxide - The Silent Hazard”, an article that was recently included in the Safety Update, Vol. 20, No. 1, 2001, published by Nobel Insurance Services.]

Jan 1, 2002

By S. Klerkx, R Battulwar, J Valencia, J Sattarvand, E Emami, M. Soleymani Shishvan

A new technology for energy distribution optimization, supported by NIOSH.

Feb 1, 2020

By Roger Favreau, Patrice Favreau

The article reviews the aspects which contribute to the quality of the results from a blast with explosives, namely a good floor, no large blocks, easy mucking, and explains the mechanisms of the blasting process which decide on the quality of these aspects for a given blast method, and how these mechanisms can be simulated from basic principles. It proposes that good fragmentation size distribution can also be important if the rock is going to a crusher, e. g. for the ore in a mine and for the rock excavated in a quarry.

Jan 1, 2012