Search Documents

By Romel B. Villanueva

At the Yanacocha gold mine, in the Andes of northern Perú, the first instrumental tests were carried out in October 2019 to detect the initiation sequence of a production blast by detecting the EMF signal produced by the detonation from each blast hole in the sequence. Several experimental tests were carried out to choose the correct antenna and find the best setup of the high-speed Data Acquisition device (DAD) to detect these electromagnetic waves. Finally, the first measurement was obtained. With the instrument recording at a rate of 1 million samples per second, the initiation sequence was detected with 99.5% accuracy. It was found that it corresponded, without a doubt, to the designed scheme. The main result is that these tests provide us with a method and instrumentation to verify if the planned initiation sequence is carried out correctly in the field. In this way we can find operational deviations and detect possible misfires. This method has proven to be accurate, fast and easy to implement, mainly requiring an EMF signal capture equipment that can record at very high speed, something that is increasingly easier to satisfy with the development of microcontrollers. On the other hand, the type of antennas used in this method are low cost and very commercial. These tests have improved our understanding of the nature of detonation and have marked a new milestone in the development of blasting instrumentation in Peru.

Jan 21, 2025

By Muhammad Yamani, Marsell Riviera, Herry Saputra, Rizky Amin

Drill and Blast processes in hot and reactive ground conditions are a severe challenge in mining, especially in the blasting process. Our main objective is safety issues without compromising the blasting outcome. Safety concerns include unexpected detonation, product damage, and misfire. However, apart from the issue of blasting safety, it is also crucial to maintain good results such as fragmentation, loader productivity, and ore dilution control. Therefore, we use a different product selection method to produce a safe and efficient blast. Pit Araren is one of the pits of the Tokatindung Gold Mine Project in North Sulawesi Province, Indonesia, classified as hot and reactive ground conditions that range from elevation of 25mRL temperature could reach to 98⁰C (208,4⁰F) based on actual measurement. The previous practice for blast holes with temperatures above 70⁰C (158⁰F) loaded with the primer that was specifically designed for hot and reactive ground conditions consisting of detonating cord and packages emulsion that specifically formulated to inhibit exothermic reaction then tied in with a combination of non-electric surface delay detonator and detonating cord initiator (short length non-electric surface delay detonator housed in plastic connector).

Feb 6, 2023

By Saeed Karimifard, Saman Nouranian, Shahram Tafazoli, Bahram Sameti, Frank Chu, Caitlin McKinnon, Tetiana Konstantynivska, Glen Turner

We propose a particle size analysis solution for haul trucks that does not impact current operational workflows. Using artificial intelligence (AI) and 3D imaging technology, our solution reliably localizes and identifies haul trucks as they drive by, then accurately calculates the particle size distribution of the visible material in each truck load. In this paper, we identify the challenges of designing and implementing the proposed solution and explain the strategies we employ to overcome these. We also discuss a method for boulder detection that leverages the existing deep learning architecture to significantly reduce crusher downtime caused by oversized rocks

Feb 1, 2020

By Favreau R. F. Ph. D, Favreau Patrice

The article explains that the way to achieve a successful blast is by insuring that the explosive energy divides properly into the weakening action of the shock wave which is necessary to prevent large collar blocks and toe, and into adequate stress field intensity SS which is necessary to obtain good fragmentation size distribution at the crusher, as well as adequate burst out rock movement to achieve easy mucking.

Feb 1, 2020

By D. Preece

The mining and oil industry employs techniques such as geologic mapping, core drilling and electromagnetic and potential field techniques to explore for new deposits. Since new discoveries of major near-surface ore bodies are becoming progressively rare and since traditional exploration methods are unable to resolve ore bodies deeper than about 500m, high-resolution seismic reflection techniques show great potential for exploration to much greater depths down to almost 3km.

Jan 1, 2011

By Douglas Bartley, Kevin Hachmeister, Rich Barry

The use of explosive energy as a tool in mining and construction is the most effective way to move large amounts of rock that is otherwise unable to be efficiently excavated. Since the early days of explosive engineering utilizing black powder initiated by cap and fuse to the present day diversity of specialty products and technologies the goal has always been to "Break and Move" as much rock for the least expense possible. It has primarily been the competitive nature of our economy that has driven the advancement of technological innovations and practice. However, the concept of removing rock is not specific to the mining and construction industry. Since the dawn of creation, man has used rock as a medium to express his creativity in the form of sculpture. Even though the process of sculpture requires the removal of rock, the final work is defined by the rock that remains intact. This typically necessitates the extreme care of the sculptor to painstakingly chip away the rock allowing the image to emerge from the original mass of stone. The famous sculptor Michelangelo once said, "I saw an angel in the marble and carved until I set him free."

Jan 1, 2004

By L. Chaves

In rock blasting, due to numerous factors, both controllable and uncontrollable, the execution rarely meets the planning. The powder factor is an important KPI for blasting since it represents the amount of explosive used to fragment the rock, therefore it depends on the rock mass characteristics and may be influenced by factors such as weathering and drilling quality. The blasts at the Serra Sul mine, S11D project, are usually big blasts and the high productivity is a challenge for maintaining the quality of the whole drill and blast process. It is important to know the contributions of each of the most common influencing factors of the powder factor to direct the efforts to the improvement of the process. A buildup model is presented to evaluate the contributions of five influencing factors to evaluate the planed x executed powder factor. The factors considered in the model are the average hole depth, the amount of hole/blasted volume, the stemming and decking length, the linear charge weight, and the density of the explosive used. The build-up may be applied for both individual blasts and for overall view of the blasts in a period. A case study is presented with the application of the model for the monthly powder factor analysis at Serra Sul mine has contributed to direct efforts to enhance drilling quality and preservation of the drilled holes.

Jan 1, 2024

By Peter Moser, Andreas Grasedieck

In modern rock blasting it is becoming more and more important to achieve a certain specified fragmentation. This means that the rock particles formed as a result of the blast should conform to a desired particle size distribution. An important issue with respect to achieve a desired blast result in terms of fragmentation is both the availability of models for the prediction of the characteristic of the particle size distribution of blasted material and the determination of the energy necessary to achieve a certain fragmentation status. Within the research project “Less Fines” funded by the European Union under project reference G1RDCT200000438, the latter has been addressed by the Department of Mining Engineering& Mineral Economics of the University of Leoben. For that purpose fragmentation results from lab scale blast tests have been analyzed and the relationship between the specific charge used for the blasts and the resulting specific surface of the fragmented material has been examined. Linear relationships between the specific charge and the specific surface of the resulting fragmentation were found for various types of rocks to apply over a range of 10 for the powder factor.

Jan 1, 2004

By Ulf Nyberg, Changping Yi, Daniel Johansson, Håkan Schunnesson

To investigate the non-ideal detonation properties of aluminized emulsion explosive, a series of tests for an emulsion explosive with 5% aluminum powder additive were carried out with mortar confinement. The velocity of detonation (VoD) and the curvature of the detonation front for different charge diameters were obtained from the tests with a high-speed camera. The burning process of the aluminized emulsion explosive has been modelled with the ignition and growth (I&G) flow model in the LS-DYNA code. A routine based on the optimization program LS-OPT code was developed to identify the parameters in the burning rate function with the detonation velocities and the front curvature radii from two tests. A Perl code was implemented in the routine and was used to calculate the VoD, fit the detonation front and obtain the detonation front curvature radii. The calibrated parameters were used to predict the VoDs and the detonation front curvature radii for the rest cases. The results indicate that both the VoDs and the detonation front curvature radii from the numerical modelling are in good agreement with the experimental results. The numerical results also indicate that the variety of the burn fraction and the peak pressure with the change of charge diameters is reasonable with the calibrated parameters.

By Ulf Nyberg, Changping Yi, Daniel Johansson, Håkan Schunnesson

To investigate the non-ideal detonation properties of aluminized emulsion explosive, a series of tests for an emulsion explosive with 5% aluminum powder additive were carried out with mortar confinement. The velocity of detonation (VoD) and the curvature of the detonation front for different charge diameters were obtained from the tests with a high-speed camera

Feb 1, 2020

By Catherine Johnson, Kelly Williams

The ability to measure the overpressure of a shock wave is necessary for explosives research such as shockwave focusing and field testing of blast-resistant designs for buildings and vehicles. To record the peak overpressure of the nearly instantaneous pressure rise at the shock front, pressure transducers with a fast response rate and streamline pencil design are needed. Time spent setting up sensors coupled with the expense of high-frequency data acquisition systems, and the inconvenience of low impedance cables can make the process challenging. Additionally, only small inaccuracies in sensor position can drastically change the measurement recorded. Advances in high-speed video imaging make it possible to see the refraction of light due to the high-density gradient at the shock front without the need for parabolic mirrors or additional light sources necessary for Schlieren or shadowgraph imaging. The average shock front velocity between two points can be calculated by dividing the change in position by the elapsed time between the images. Using the Rankine-Hugoniot relationship demonstrated by Swisdak the peak overpressure of the shock wave can be calculated from its velocity eliminating the interference of the gage and mount. This paper investigates the accuracy of this method by setting dual transducer pencil probesat0and180 degrees perpendicular to the central axis of a285-gram(0.63-pound)cylindrical charge to record pressure versus time for comparison to the high-speed video. The axis of the camera lens is aligned with the central axis of the charge with both pencil probes in view. The pencil probes have two pressuretransducersset100millimeters (3.9 inches)apart to measure the time of arrival and are used to validate the velocities calculated from the high-speed images. This method can be used to evaluate the shock wave propagation from more complex prismatic charges with different cross-sectional shapes where precise placement of cumbersome pencil transducers in the near field is almost impossible.

By Nicholas Matthews, Vilem Petr

This project will report findings on the establishment of a new surface test site at the Colorado School of Mines Edgar Mine. Concerns over the blast effects on site neighbors prompted the study to be conducted. The current maximum charge weight of 20-lb was studied to ensure that all environmental effects were within the range prescribed by state and federal regulations. Geophone locations were surveyed using GPS and monitored using Instantel Minimate Plus instruments. Distances and orientation of measurement sites to the test site were varied according to the local geography and geology. Weather conditions were also observed and recorded during all tests. Neighbor complaints were recorded and taken into account during analysis. Current results show that the current charge limit results in a safety factor of over 200 for all blasting activities at the site. Data collection is ongoing and a review is to be conducted annually. These results will be presented in the future. Results are presented and discussed in the following paper. Copyright

Jan 1, 2010

By J. Rafael Otaíza, Francisco Mardones

This work has addressed the problem of creating a predictive model of the maximum particle velocities in the rock mass (PPV). The model designed specifically can model the subsequent vibrations of blasting based on geometric parameters, explosive loading, and the blasting process itself. Models based on artificial intelligence (AI) algorithms can find useful non-linear patterns to solve classification, regression, clustering, among other problems. They are flexible mathematical transformations adaptable to various objectives and types of data. With their different levels of abstraction, they can find a function that relates the input variables to the sought-after response. These models have been successfully used in similar contexts (Prashanth, (2018)) and have achieved state-of-the-art results in the field (Lawal, (2021)). The main challenge is to adapt them to the context of Chilean mines, in addition to including the geometric information of the blasting and the heuristic to obtain the set of optimal parameters, it is proposed to follow the work of (Simonyan, (2013)) and obtain "saliency maps" adapting it to tabular variables. We implemented an Artificial Neural Network (ANN) with a large number of neurons in the hidden layers. Models based on neural networks can find useful non-linear patterns to solve classification, regression, clustering, among other problems. They are flexible mathematical transformations adaptable to various objectives and types of data. With their different levels of abstraction, they can find a function that relates the input variables to the sought-after response. The literature shows that, for the problem of rock type identification, basic neural networks perform well (Simonyan, (2013)), but lack uncertainty estimates. This is a data-driven model, and in this sense, the model training was carried out using data from multiple operations in the large copper mining industry in Chile. In these databases, data consistency and the balance of the various independent variables that have the greatest impact on the model were ensured. With the above, the optimal hyperparameters of the model were determined, obtaining a predictive R-squared of 0.94.

Jan 21, 2025

By Emily Johnson, Catherine Johnson, Ben Sonpon, Kelly Williams

The effect of length to diameter of the detonator is compared using Ansys/Autodyn 2-D simulations, the results of which are validated experimentally. It was found that higher pressure comes with a larger diameter, because it will result in more explosive energy being allocated out the end of the detonator.

Feb 1, 2020

"Large scale open pit mining and quarrying operations dictate safe and reliable pit wall stability. The current approach of employing the particle velocity-scaled charge distance approach to estimate and minimize damage to residential structures is considered inadequate to protect rock slopes. This study utilizes close-in blasting vibration data as input to an advanced 2D numerical code to study its applicability to serve as a predictive tool in terms of blast-induced rock slope failure. Two tri-axial accelerometer stations, consisting of high-frequency and high-amplitude (20 kHz, 100g) sensors, located within ~100m of the blast, but at two different bench levels, were used to monitor a production blasting in a quarry. The production blast consisted of double-decked explosive loads in 155 mm (6 in) diameter holes, with an inter-deck delay of 42 ms, and each deck consisting of 130 kg (285 lb) of emulsionexplosive. The blasting vibration data obtained at the two bench levels were critically analyzed, and thevibration results served as input to the numerical model consisting of a single rock block with a 45 degree persistent joint plane but with specified strength properties, significantly different from that of the intact rock. The model was able to characterise progressive accumulation of damage in the form of micro-cracks along the joint surface as a function of the vibration load from successive explosive decks. The results showed that such a numerical model can serve as a very good diagnostic and predictive tool, when backed up by careful vibration monitoring and further supported by detailed slope monitoring."

Jan 1, 2017

By A. S. Tawadrous

Fines are produced in any blasting application. Depending on the application, fines may or may not be a desirable product of the blast. In most quarry and construction applications, fines are considered an undesirable product since it does not constitute a sellable product and there are costs to the operation for disposal. On the other hand, in most open pits fines do not represent as much of a problem since the ore has to be crushed and ground after being blasted. Therefore, fines in such operations may reduce the energy consumed in the downstream operations.

Jan 1, 2012

By J. D. Aubertin

Rock blasting is a complex engineering process that requires in-depth knowledge of operations and geomechanical conditions. Acknowledged design precepts are based on cratering behavior associated with stiff hard rock masses. Other cratering mechanisms may however arise under certain geomechanical conditions such as extremely fractured rock masses, or with soft rocks such as rock salt and potash. The burden dimension also plays an important role in the prevalent cratering mechanisms of a given blasting condition. The present article investigates the variability of cratering profiles and geometrical trends based on characteristic geomechanical differentiation and considering the influence of burden. The differences in observable mechanisms are examined through small and large-scale single hole blast (SHB) tests. SHB tests involve a series of individual shots blasted parallel or sub-parallel to an open face. The burden dimension is varied to obtain burden dependent characteristic trends. The breakout shape is represented by a crater model in the form of a power law equation capable of describing prismatic, concave and convex cratering. The formulation comprises two reference index parameters that can describe the geometrical and geomechanical conditions. SHB test campaigns conducted in rock salt, limestone, massive amphibolite, pinolite, and grout blocks are compiled in quantitative manner to demonstrate the influence of geomechanics on cratering profiles. The observed trends are corroborated through numerical modelling carried on Finite Element Model (FEM) LS Dyna to investigate the prevalence of specific cratering mechanisms. A series of SHB tests at large and small burden values are also used to showcase the influence of geometry on the prevalent cratering mechanism and the resulting crater

Jan 1, 2024

By M. Szumny, P. Mertuszka, K. Fuławka

Multi-face destress blasting is the basic method of reducing rock bursts hazard in Polish copper mines. Blasting operations of this type are carried out regularly, twice a day in order to minimize the geomechanical threat while maintaining high extraction efficiency. Unfortunately, the assessment of the effectiveness of this type of work until recently was based solely on determining whether a given destress blasting triggered a seismic tremor or not. Information on the characteristics of seismic waves generated by blasting has so far been omitted in analyzes of this type. The lack of reliable knowledge about the generated seismic effect makes the introduction of constructive corrective actions impossible, which in turn significantly reduces the triggering potential of conducted destress blasting. This study presents the results of comprehensive work aimed at increasing the effectiveness of active rock burst prevention in Lubin underground copper mine. For this purpose, an innovative system for continuous monitoring of seismic waves induced by multi-face blasting was developed, and a new method for seismic assessment of the effectiveness of the destress activities was developed. Based on the monitoring data and the comprehensive analysis of waveforms, the effectiveness of individual blasting operations was determined, and on this basis, modifications to the drilling and blasting patterns aimed at increasing the generated seismic effect were proposed. The use of innovative methods of monitoring and data analysis made it possible to increase the effectiveness of the conducted activities, in terms of the magnitude of seismic vibrations, up to 250%. It should be emphasized that the introduced modifications were aimed at increasing the effectiveness of blasting operations while maintaining the current level of costs. As a result, the proposed solution turned out to be highly effective, significantly affecting the safety of the work carried out in Polish copper mines. Thus the proposed approach is planned to be implemented in other Polish copper mines belonging to KGHM in the near future

Jan 1, 2024

By E. McCullough, D. Preece, M. Ortel

The mining and oil industries employ techniques such as geologic mapping, core drilling and electromagnetic field techniques to explore for new deposits. New discoveries of major near-surface ore bodies are becoming progressively rare and traditional exploration methods are unable to resolve ore bodies deeper than about 500 m (1640.4 ft). Consequently high-resolution seismic reflection techniques show great potential for exploration to much greater depths down to almost 3 km (1.9 mi).

Jan 1, 2013

By Jeffrey W. Lin, Jonathan D. Abbott, Patrick R. Bowden, Tyson J. Plitt

Pentolite is a class of high explosives containing trinitrotoluene (TNT) and pentaerythritol tetranitrate (PETN) with PETN content typically ranging from 40 to 60 wt%. Manufacture involves melting TNT, 80 °C, followed by addition of PETN and trace ingredients to form a homogeneous mixture. Once a mix is ready to be poured, several factors can influence the behavior of the finished product including how long the mix has been at temperature and cooling rate. After the manufacturing process has been completed, storage conditions combined with manufacturing conditions may cause physical changes. Two such changes explored were exudation, liquid exuding from solid boosters, and ratchet growth, irreversible volumetric expansion. Exudation is principally caused by excess water in the process. Ratchet growth is a common phenomenon of nitroaromatic compounds such as TNT where time and temperature fluctuations can cause materials to increase volume, simultaneously decreasing density. Although neither phenomenon affects common attributes such as sensitivity, performance, and shelf-life, both can cause issues in storage and handling. In this study pentolite was cast into various forms under different manufacturing conditions and evaluated over several months of controlled storage conditions including ambient, temperature cycling and elevated isothermal. Subjective and objective measurements were made throughout the evaluation period with the aim to determine the preferred storage methodology.

Jan 21, 2025