Search Documents

By T. J. Lutz, G. T. Homce

A standard Ford1 4600 agricultural tractor was converted to remote control to perform ASAE/SAE field upset tests (rear rollover and side rollover). This paper discusses the engineering process to develop a remote-controlled tractor in determining the critical parameters of operation, to choosing appropriate actuators, designing the circuitry to control them, installing the actuators on the tractor, testing the system for functionality and then conducting numerous overturn tests. The system uses off-the-shelf components for simplicity, replaceability, and economic concerns. The remote control system has withstood 21 tests to date with no failures and will continue to be used for at least three more years of testing.

By M. Kanda

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in and above an operating coal mine, McElroy Mine, located near Moundsville, West Virginia. The electromagnetic environment created by 300 volt dc and 480 volt ac machinery was measured. In one technique noise was measured over the entire electromagnetic spectrum of interest for brief time periods. The noise was recorded using broadband analog magnetic tape. The noise data was later transformed to give spectral plots. In the other technique, noise amplitudes were recorded at several discrete frequencies for a sufficient length of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 1, 1974

By R. Marshall

Electrical trailing cable handling techniques and practices used in metal and non-metal surface mines were investigated by obtaining information through actual visits to the mine properties located in a variety of geological areas and climatic conditions. An analysis was made of all accidents related to cable handling which are cataloged by HSAC* for the period from 1971, through June 1980. Information was also collected from mine operators concerning near accidents and non-reported accidents. The results of this investigation were presented to the U.S. Bureau of Mines in an effort to outline recommended practices for cable handling in surface mines and to recommend additions and/or changes in the present regulations now being enforced by MSHA** field inspectors. These recommendations are also intended to assist the U.S. Bureau of Mines in evaluating the need for assisting the mine operators in the areas of training and distribution of information related to material handling of trailing cable. * Health Safety Analysis Center ** Mine Safety & Health Administration

Jan 1, 1980

By C. A. Hesse

The Quartz Hill Molybdenum Project, In Southeast Alaska, was the first mining project to attempt the permitting of a submarine tailings disposal system in the United States, since the passage of the National Environmental Policy Act of 1969 and the Clean Water Act of 1977. Over $20 million was spent by the project developer in baseline data gathering and In funding the preparation of the four Environmental Impact Statements and other environmental documents required at various stages of the project between 1977 and 1988. Because of the timing and a unique set of environmental, legal and regulatory requirements which applied to this project, innovative approaches were developed. This report describes those requirements and the developments, and gives a full historical account of the campaign for permitting submarine tailings disposal at Quartz Hill, until denial of the NPDES permit application by EPA in September 1 990. The extensive studies done for Quartz Hill suggested that under certain conditions the selection of submarine tailings disposal can be the overall environmentally preferred alternative for a mining project. The Quartz Hill story illustrates the complexity of the existing permitting structure and paints out the desirability of rationalization to achieve a more effective system.

Jan 1, 1993

This publication summarizes, for potential contractors and other interested parties, the research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1980 (October 1, 1979 - September 30, 1980) under its Minerals Health and Safety Research program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1980

By Roy L. Wilfong

The thermal decomposition of the ammonium sulfate, carbonate, nitrate, oxalate, and sulfate salts of praseodymium, neodymium, and samarium was investigated thermogravimetrically in the temperature range 25° to 1,500° C. Each salt was decomposed at a heating rate of 2.5° C, per minute. The pyrolytic sequences have been identified and the temperatures of formation of inter-mediates, the minimum oxide formation temperatures, and values for loss on ignition have been determined. The nonstoichiometric ranges between Pr6011 and Pr203 and the extent of these ranges have been determined for oxides derived from the carbonate, nitrate, and oxalate salts of praseodymium. The alum and sulfate salts of praseodymium produced the sesquioxide without forming the intermediate non-stoichiometric oxides. The temperature limits of formation and regions of stability for the alums and sulfates were better defined than were those for the carbonates, nitrates, and oxalates. The minimum oxide formation temperature increased in the order of samarium, neodymium, and praseodymium irrespective of the anion.

Jan 1, 1962

By R. F. Chaiken

The Bureau of Mines has carried out experimental and theoretical studies with prilled and pulverized ammonium nitrate-fuel oil (AN-FO) mixtures containing varying amounts of fuel oil in an attempt to quantify the effects of stoichiometric composition, nonideal detonation behavior, and expansion volume on the production of CO, NO, and N02 fumes. Experimental fume measurements were obtained in the Bureau's large closed gallery facility (7.2 X 104 liter expansion chamber) and in the standard Crawshaw-Jones apparatus (90--liter expansion shamber) using a prepackaged charge configuration containing about 450 g of explosive.4 The theoretical calculation of toxic fumes was achieved with an equilibrium detonation code called "TIGER,," Contrary to initial expectations, the NOx (= NO + N02) fumes from the large gallery test were found to be in essential agreement with the Crawshaw-Jones results. It was also concluded that (1) "TIGER" calculations offer a good approach to the prediction of toxic fumes; (2) there is a basic problem in extrapolating laboratory measurements of CO fumes to mine conditions--this being due to postdetonation oxidation of CO to CO2; and (3) the detonation velocity decay rate of an explosive is a useful experimental parameter for correlating toxic fumes production with nonideal detonation behavior.

Jan 1, 1974

By George J. Conroy

To provide data as a basis for proposed acceptance standards and procedures covering permanent splices in trailing cables, the Bureau of Mines conducted testing programs on the flexure life in flat types W and G dc trailing cable splices and ground conductors. Primary reliance was placed on laboratory testing, although some cross comparisons were made at manufacturers' plants and mine operations Besides providing data for acceptance standards and procedures, results of the program should promote the general improvement of commercially available splice kits.

Jan 1, 1977

The contract objective was to evaluate sources of airborne quartz and research control methods that would assist underground mine operators in complying with respirable dust standards which have been reduced because of quartz in the dust exceeding five percent. The work involved: Phase I -evaluate sources of quartz dust at the roof bolter work location; Phase II -evaluate the relationship between the quartz content of the coal and adjoining rock strata and quartz exposure at the roof bolter and continuous miner locations Phase III -conduct laboratory tests to determine performance parameters for roof bolter dust collector systems. The underground surveys for Phases I and II determined: (1) the continuous miner typically is the greatest source of quartz exposure for the miner and roof bolter operators when single-split ventilation is utilized, (2) a statistically significant relationship be­tween quartz content in face material and operator exposure was not determined and data suggested mining equipment and procedures may be more critical. The Phase III lab tests indicated the use of dust hog-type bits, filter cartridges, maximized collector airflow, and reduced bit rpm should be utilized to minimize dust liberation at the roof bolter.

Jan 1, 1985

By B. J. Moore

This publication contains analyses and related source data for 352 natural gas samples from wells and pipelines in 18 States and 5 foreign countries. All of the samples were obtained and analyzed during calendar year 1974 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economics. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576.3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the public in general. Sixteen previous publications have presented the results of 10,479 gas analyses prior to 1974. The first three, Bulletins 486,4 576,5 and 617,6 contain analyses and related source data on

Jan 1, 1975

By G. F. Livingston, F. K. Shelton, J. C. Stahl, R. E. Churchward

"INTRODUCTION An investigation of the metallurgy of cobalt from domestic ores has been in progress since February 1940 and has resulted in the formation of a hydrometallurgleal process for the production of electrolytic cobalt metal. Previous reports of these investigations have been given by F. K. Shelton; 7/ and Ruth E. Churchwrd, F. K. Shelton, and G. Knickerbocker. 8/ Briefly, the process, as applied to ores containing cobalt oxide, consists of leaching with H2SO3 or, preferably, with H2SO3 and H2SO4, to dissolve the cobalt. The cobalt solution passes through one or more purification stages to remove iron and elements of the copper group, and cobalt carbonate is precipitated under carefully controlled pH conditions. The cobalt carbonate is dissolved in on acid electrolyte containing sulfuric acid, boric acid, and sodium fluoride. The electrolyte then proceeds to electrolytic cells where cobalt is plated as a metal and sulfuric acid is regenerated.The present paper contains the results of several investigations signed to give a more complete chemical and engineering understanding of different unit processes involved in the electrowinning of colbat. Some work has been done to broaden the process to include arseniferrous cobalt ores as well as the oxide ores upon which the investigation was initiated. Most of the data presented herein have been obtained since the release of the previous reports; any changes suggested heroin that conflict with recommendations in earlier reports are based on more complete data and usually are preferable."

Nov 1, 1945

By R. C. Ellman

Since successful industrial lignite-burning equipment was developed in 1925, the commercial use of lignite as a fuel for power plants has increased. It has proved an entirely satisfactory fuel for generating power and can be burned efficiently by various methods.4/ Equipment to fire pulverized lignite was installed and used successfully at the Trinidad Station of the Texas Power & Light Co. as early as 1926. The lignite was predried in steam-heated grid driers before pulverizing.5/ This method of firing was used later in the Comal Station of the San Antonio Public Service Commission.6/ Both stations, however, have since been converted to use other fuels. Units for pulverizing and drying lignite are relatively new in the lignite-consuming region of North Dakota. The air which sweeps the pulverizer and transports the pulverized product to the burners is preheated to dry the lignite during pulverization. The first unit was installed in 1948 in one of the two boiler units of the Crookston Station, Otter Tail Power Co., Crookston, Minn.7/ In 1951 the 30,000-kw. W. J. Neal Station, Central Power Electric Cooperative, Inc., Voltaire, N. Oak., was designed and constructed for firing pulverized lignite exclusively. It is the largest lignite-fired, power-generating station in North Dakota. The 44,000-kw. Lewis and Clark Station of the Montana-Dakota Utilities Co., Sidney, Mont., is fired by a similar pulverizing system. Operation of this plant was begun in October 1958. At Fergus Falls, Minn., the 53,500-kw. Hoot Lake Station of the Otter Tail Power Co., also using a pulverized lignite-firing system, began operating in September 1959.

Jan 1, 1961

This Bureau of Mines report is devoted to descriptions of investigations pertaining to underground mine trailing cables, their handling, splicing, and the use of couplers.

Jan 1, 1979

By V. A. Marple

At the Twin Cities "lining Research Center (TCMRC) a project is underway to determine how varying the parameters of a coal-cutting process would affect the amount and the size distribution of the generated dust. The cutting parameters being investigated are the cutting speed, depth of cut and shape of the cutting, tool. To accomplish this research ft is necessary to collect and transport the coal dust venerated at the cutting tool to measuring instruments for analysis. The purpose of this contract was to develop and deliver a system of instruments for measuring the size distributions of the generated coal dust. The instruments employed are essentially those developed for particulate air pollution measurements (1, 2). The instrument system covers a particle size range of 0.005 to 20 microns and is capable of performing in situ measurement and presenting data in real time.

Jan 1, 1974

By M. M. Fine

Research on the solid-fuel reduction of Knob Lake iron or was conducted to upgrade lean and high-grade ores and recover metallized products suitable for ironmaking or steelmaking. The program included bench-scale tests plus a number of continuous campaigns in a 34-inch by 36-foot rotary kiln. In the laboratory, metallizations in excess of 90 percent were achieved by reduction of crushed ore with lignite at 950° C. Subsequent grinding (to minus 200 mesh) and wet magnetic separation yielded concentrates analyzing less than 3.0 percent SiO2 and more than 90 percent Fe. Virtually complete recovery of the iron occurred. During early continuous tests the crushed ore created a serious ringing in the kiln which was solved by balling the fines with bentonite. Unfortunately, at this temperature (950° C) the bentonite militates against the concentratability of the metallized product. For example, a run on direct-shipping ore produced concentrates of 89.5 percent Fe and 4.5 percent SiO2. At 500° C the adverse effect of bentonite disappeared and concentrates of 88.4 Fe and only 2.5 percent SiO2 resulted. However, with comparable feed r Los, the metallization dropped to 73 percent.

Jan 1, 1969

By Martin H. Rogoff

This publication combines a critical review of the literature on the microbiology of coal with an introduction to those areas of microbiology related to studies of coal as a biological material. The attack on coal by microorganisms as yet remains doubtful. Only the low-rank coals contain an indigenous microbial flora, and even these organisms are not peculiar to coal, but are common soil and water forms. No experimental data have as yet been presented, either in the literature or in the present work, which unequivocally demonstrate the oxidation of coal by microorganisms. Reasons for the resistance of coal to such attack, including insolubility, physicochemical structure, steric hindrance of enzyme action, and the presence of antibiotic materials in coal are discussed. Microorganisms do attack large aromatic molecules and the mode of oxidation of aromatic ring systems by bacteria is presented. Well-defined pathways are known for the oxidation of polycyclic compounds with one to three rings, and these paths with their key intermediates are described and related to the possible oxidation of coal.

Jan 1, 1962

By John C. Machisak

DATA ON INJURY experience at quarries and related plants of the United States are presented in this publication under the following general sections: A) General injury experience: Tables 1-4: Contain current data on number of injuries, injury-frequency rates, work location, accident agency, degree of injury, and related employment data. (B) Injury experience at different kinds of quarries: Tables 5-6: Current data on number of injuries, injury-frequency rates, work location, accident agency, degree of injury, and related employment data. (C) Injury experience by States: Tables 7-19: Current data on the number of injuries, injury-frequency rates, accident agency, degree of injury, and related employment data. (D) Selected injury data: Tables 20-30: Current data on various selected factors of operating conditions at different kinds of quarries, including employment size-groups, length of shifts, comparative severity of injuries, and injury data and related employment experience at dimension-stone and crushed and broken stone quarries, and underground quarries. (E) Mining methods and historical injury experience: Tables 31-32; Employment data and injury experience in the quarrying industries of the United States, by mining method and work location, 1953-58; and historical injury experience and employment data in the quarrying industry, 1911-58.

Jan 1, 1962

By Ross W. Smith

Microflotation and surface chemical studies were conducted on a chromite from the Stillwater Complex in Montana and on some of the minerals usually found to be associated with such chromites. Considering the chromite it was found that aging the ground mineral in air or heating it markedly affected its flotation behavior. Much of the observed effects could be attributed to oxidation reactions involving surface chromium and iron species. Strongly acid pretreating the mineral appeared to reverse such effects. Thus, it can be concluded that the manner in which the mineral (or the ore) is pretreated is of utmost importance in its flotation. Work carried out on associated gangue minerals determined how they are likely to behave in a flotation environment and how certain foreign ions derived from a chromite ore itself can affect their surface characteristics and, thus, presumably also their behavior in a flotation circuit.

Jan 1, 1981

By Frank B. Fulkerson

Of the about 60 million pounds of aluminum used in the Pacific Northwest in 1960, 40 million pounds or two-thirds was used by 10 companies. One of these companies made airplanes and missiles; one manufactured roofing, siding, and tubing; three produced truck tractors, truck bodies, or truck trailers; two made architectural metal products; one made irrigation and industrial products; one was a general foundry; and one was a shipyard. These companies contributed to regional growth by developing markets outside the area; some have worldwide sales. Aluminum consumption increased at an average rate of 7 percent annually from 1954 to 1960. Airplane manufacture, formerly preeminent in aluminum use, no longer was in first place in 1960. By industrial group, the leading users were manufacturers of building products, 30 percent; airplanes and missiles, 22 percent; truck tractors, truck bodies, and truck trailers; 17 percent; general foundries, 5 percent; ships and boats, 4 percent; mobile homes, 4 percent; other transportation equipment, 3 percent; and irrigation equipment and all other products, 15 percent.

Jan 1, 1962

Protect mine rescuers from heat-induced stress that drastically cuts their endurance and saps their strength. Approach To prevent exhaustion caused by thermal stress, a rescuer can wear a liquid-cooled hood and vest which absorbs heat, thereby reducing the heat-induced strain on the rescuer's heart and circulatory system. How It Works Liquid coolant is continuously circulated through a self-contained system in which the coolant is chilled by a heat sink on the wearer's belt. The coolant, which is a mixture of alcohol and water, is pumped from the heat sink to bladders inside the hood and vest where it absorbs body heat. After absorbing heat In the hood and vest areas, the coolant returns to the heat sink where it is rechilled by passing through a tube coiled around a steel can containing a block of ice. To adjust the temperature of coolant leaving the heat sink unit, a valve can be operated by the wearer, causing part of the flow to bypass the coil. A small pump and a rechargeable battery are also part of the assembly.

Jan 1, 1979