Search Documents

By Alvin M. Cummings

During the period from June to September 1943, the Bureau of Mines undertook an investigation of the Vial mine, near the village of Linden I in Iowa County, Wis., as part of a general investigation of the zinc-producing area of southwestern Wisconsin. The work was done when every effort was being made to increase the production of metals important to the Nation's war program. The Bureau completed 29 churn-drill holes aggregating 3,348 feet of bore in areas immediately north and west of the old Vial mine, which had been worked intermittently between 1908 and 1939. The drilling supplemented a previous drilling program by the lessees and disclosed the presence of two significant zones of mineralization.

Jan 1, 1948

By D. T. Holmes, W. G. Sandell

"INTRODUCTION Three representative lots of ore wore obtained from the Aguila minim district in Arizona during the Bureau's exploration of manganese deposits there. Since only selectively mined ore from this district will meet commercial-grade specifications, the ores were studied to determine their amenability to concentration.Although the purpose of the investigation was to determine the possibilities of the district as a source of commercial-grade manganese, testing was sufficiently comprehensive to indicate the response of the ores to several different types of treatment. Many data of secondary importance have been omitted, end only the more pertinent tests are presented in detail.At the beginning of the investigation of manganese-ore beneficiation in December 1940, the only product marketable to. Metals Reserve Company was ferro-grade manganese, grade B, the requirements for which follow: Mn, min., 48 percent; Fe, max., 7 percent; Si02, max., 10 percent; P, max., O.18 percent; Al12O3, max., 6 percent; Zn, max., 1 percent.Later the specifications were modified gradually. As of May 15, 1943, manganese products were acceptable if they contained over 35 percent manganese and less than 3 percent zinc and 1 percent phosphorus. Prices were based upon material containing 48 percent manganese, 6.O percent iron, and. 11 percent silica plus alumina. Premiums were paid for manganese con¬tent over 48 percent and iron content under 6 percent, penalties being imposed upon products containing loss than 48 percent manganese or more than 6 percent iron or more than U. percent. silica plus alumina.. The specifications for commercial manganese further required that the maximum particle size be 12 inches and that 75 percent of the product be coarser than 20-mesh. Therefore, fine material, such as table and flotation concentrates, had to be nodulized or sintered. In addition, carbonate manganese ores were not acceptable unless calcined.."

Aug 1, 1948

By D. A. Reynolds

A few studies on the relationship of the fusion temperature of the ash on coke to that of the corresponding coal have been made on commercial high-temperature cokes. H. J. Rose3/ in 1921 compared the fusion temperatures of the ashes of 10 coals and the cokes produced from them and concluded that they were in such hose agreement that either figure could be used. More recently, Quarfort4/ found that the ash of coke fused at a somewhat lower temperature than that of the original coal. As the ash of a coal and that off tie coke produced therefrom have the same origin their chemical composition should be identical, provided that carbonization has not altered the inorganic, or ash-forming, constituents of the coal, and such alteration seems highly improbable. However, it has been shown5/ that coke is liable to contamination by iron during crushing and grinding preparatory to sampling. Pieters6/ found that coke ash was contaminated in this manner up to 0.4 percent. Extraneous iron would lower the ash-fusion temperature because such iron may form ferrous silicate, which is readily fusible.7/ These results provide a basis for the prediction that the ash of coke will fuse at a lower temperature than that of the corresponding coal, especially if the fine grinding of the coke was done by rubbing -surfaces of iron, as in a disk pulverizer or bucking plate.

Jan 1, 1940

By Robert H. Bedford

As a result of the Bureau's general survey of quicksilver deposits in California, the Guadalupe mine area was among those chosen for exploration. Exploration, such as that at the Guadalupe, was aimed primarily at maintaining or increasing production of quicksilver during the critical wartime period. The project as originally planned contemplated sampling the dumps and prospecting some promising surface exposures by bulldozer trenches. Salvage was the objective in the first case and new ore in the second. Later, a program. of diamond drilling was added, designed to add both to ore reserves and to geological information. This report summarizes the history, notes the location and physical features, mentions property and ownership, and presents a brief description of the mine. The geology is outlined, and the work done by the Bureau of Mines is explained and supplemented with accompanying maps. The work involved repairing 1-1/4 miles of roads; bulldozing 13 trenches by removing 2,345 cubic yards of dumps to provide for sampling; digging and sampling 9,284 linear feet of hand trenches, digging and sampling numerous test pits; and drilling 7 diamond-drill holes, totaling 1,000 feet. A total of 419 samples, including 10 percent check samples, were taken. Exploration work in California at the time of this project was under the direction of Spangler Ricker, supervising engineer of the California field office, the late Robert Bedford was in charge of the fieldwork on this project.

Jan 1, 1950

By D. D. Walker

Scheelite, the most abundant tungsten mineral in the Philipsburg region of Montana, is found in replacement deposits and along fissures and cracks in limestone at various distances from contacts with acidic igneous rocks. It also occurs at the limestone-igneous contacts, but typical garnet tactites are developed in only a few places in the region. The most favorable host rocks for scheelite mineralization are the Jefferson, Hasmark, and Madison limestones. Scheelite is exposed in float, outcrops, and surface and mine workings along a 2-mile-wide belt extending southwest from Lost Creek beyond Silver Lake, a distance of 15 miles or more. (See fig. 1.) Some scheelite is found in veins formerly mined for silver. Powellite and molybdenite occasionally are present with the scheelite. Hubnerite occurs in quartz veins in the Black Pine area 10 miles northwest of Philipsburg. These quartz veins occur in the quartzites of the Precambrian Spokane formation. Tungsten production in the region has come almost exclusively from scheelite deposits, both lode and placer. During a 6-year period beginning in 1943 a total of 142.0 tons of 63-percent W03 concentrate was produced by H & H Mines Co. In the early 1950's, the Trigger mine produced 4,000 tons of 1-percent W03 ore and the Tip Top 650 tons of 2.0-percent W03 ore and 2,906 tons of 2.2-percent ore. There has been sporadic production from some of the smaller properties in the area.

Jan 1, 1960

By Charles B. Carpenter

[The Bureau of Mines selected Anahuac for a petroleum-engineering study because it is one of the notable fields of the Gulf Coast region. It is outstanding because the producing formation is very thick; ever modern technique of drilling' and development has been applied; complete records of all operations,, including detailed subsurface information have been kept; the field has ,been developed systematically; and every effort has been made to utilize the reservoir energy efficiently. Data and information pertaining to the development anal operation were collected, compiled, and studied by the writers as if the field were under single ownership. The chief aim of the study was to increase the accuracy of the existing methods of estimating reserves by applying all the data collected during the modern development of an oil field, These scientific aids include coring; electric logging; micropaleontology determinations of porosity, permeability of oil-bearing sands, and their connate water content; subsurface sampling of the reservoir oil; and depth-pressure measurements. Because the reservoir structure in the Anahuac field is extremely complex, special attention was given to methods of calculating the reservoir volume.]

Jan 1, 1941

By Charles B. Carpenter

[The Bureau of Mines selected Anahuac for a petroleum-engineering study because it is one of the notable fields of the Gulf Coast region. It is outstanding because the producing for is very thick; every modern technique of drilling' and development has been applied; complete records of all operations,, including detailed subsurface information have been kept; the field has been developed systematically; and every effort has been made to utilize the reservoir energy efficiently Data and information pertaining to the development anal operation were collected, compiled, and studied by the writers as if the field were under single ownership. The chief aim-of the stud,, was to increase the accuracy of the existing methods of estimating reserves by applying all the data collected during the modern development of an oil-field, These scientific aids include coring; electric logging; micropaleontology determinations of porosity, permeability of oil-bearing sands, and their connate water content; subsurface sampling of the reservoir oil; and depth-pressure measurements. Because the reservoir structure in the Anahuac field is extremely complex, special attention was given to methods of calculating the reservoir volume.]

Jan 1, 1941

By V. B. Dale

San Manuel has been a modern prodigy from its inception to its present status as a block-caving operation producing 33,000 tons per day. The deposit was discovered, prospected, and developed with modern techniques, and nearly all planning was done from results of an extensive drilling program through an average overburden of 670 feet. The Federal Government had a prominent part in the discovery and primary development of San Manuel. The first 17 holes were drilled by the Bureau of Mines, and discovery of the large, low-grade, disseminated copper deposit is credited to the Bureau. A loan fund of 94 million was granted through the Reconstruction Finance Corporation to the San Manuel Copper Corp. for development of the deposit and erection of concentrating and smelting facilities. Then, while the mine was still being developed, the Defense Materials Procurement Agency contracted to buy a large amount of copper at a pegged price.

Jan 1, 1962

By Philip Thompson

The Bureau of Mines investigated a selective flocculation-flotation technique to remove insoluble slimes from low-grade potash ore in a continous 45-kilogram-per-hour (100-pound-per-hour) process investigation unit (PIU). This research is part of the Bureau's program to improve resource recovery from low-grade ores. Results showed that 84 percent of the insoluble slimes were removed from an ore containing 5.5 percent water-insolubles and 14 percent K20 using a Bureau-developed, cationic flocculant-glycol ester-diesel oil reagent. Subsequent potash flotation recovered 75 percent of the potash in a cleaner concentrate assaying 56 percent K20. Concentrate leaching upgraded the product to market specifications of 60 percent K2O. An economic evaluation by the Bureau suggested that the rate of return on investment, after taxes, should be about 20 percent for such an enterprise.

Jan 1, 1980

By Ronald P. Hollenbeck

The value of mineral production in Alabama increased 1 percent above the record high set in 1965. Alabama ranked second among the States in the production of bauxite, third in the production of masonry cement, native asphalt, and scrap mica, sixth in the production of portland cement, ninth in the production of iron ore, and tenth in the production of lime. The mineral industry of Alabama was dominated by the mining and processing of coal and stone, the manufacturing of cement, and the production of crude petroleum. These industries accounted for 87 percent of the State's total value of mineral production, compared with 85 percent in 1965.

Jan 1, 1967

By Reno M. Pappas, Christopher Mark

This report presents results of a U.S. Bureau of Mines study of longwall gob material. The objective of this work was to determine material stiffness properties of the gob for use in numerical models of rock mass response to longwall mining. Photographs of actual mine gob were digitized to obtain approximate particle size gradations of gob material. The gradation curve was shifted down to a lab- oratory scale, and 20 uniaxial compression tests were conducted. Varying the maximum particle size was not found to affect the stress-strain behavior, but changing the gradation appeared to influence the stress-strain behavior. The stress-strain relationship of the simulated gob material was nonlinear, the stress-secant-modulus relationship, was approximately linear, and the stress-tangent-modulus relationship was approximately a second-order polynomial function. Equations were generated from these curves, providing numerical modelers with a means to estimate gob moduli based on the stress level. In addition, the experimental data were statistically evaluated using multiple regression analyses, producing a series of equations to predict the secant and tangent moduli from the given stress level, bulking factor, rock strength, and thickness-to-width shape ratio of the particles.

Jan 1, 1993

By Frank C. Townsend

Centrifugal model embankments with varying geometries and materials were constructed of- coal waste material, accelerated From 100 to 120 times earth's gravity, and subjected to various throughflow rates until failure occurred. Complementary laboratory tests were performed on the waste materials to obtain strength and permeability parameters for analytical calculations to predict observed centrifugal model behavior. Failures in the form of deep.-seated failure, or erosion and sediment transport or a combination of both, occurred in model embankments with 1V:1-1/2H and 1V:2H slopes when the phreatic surface due to seepage exited on the downstream slope: Positive seepage control, i.e., a toe drain successfully prevented sloughing and failures. Slope stability analyses agreed well, albeit conservatively, with observed model performance. Factors of safety ranged from 0.7 to 1.02 at the instant of failure for models with retrogressing slips as compared with 1.05 to 1.7 for stable embankments, These models verified existing criteria of a minimum safety factor of 1 3 and the necessity of positive seepage control.

Jan 1, 1980

By Bruce D. Sartwell

A program was written which utilizes a remote teletype input to a time- sharing computer to plot charged particle or X-ray energy spectra which are stored in the memory of multichannel analyzers. The program, written in FORTRAN V, accepts the data printed out by the pulse height analyzer on paper tape and then, after reading these data tapes into the computer, plots on the teletype the desired energy spectra on a scale automatically adjusted for the maximum number occurring in the data. The program is flexible enough so that the researcher can subsequently expand or contract the vertical (intensity) or horizontal (energy) scales. With a slight modification, the program will accept data printouts from scalers or analog to digital converters. The program also includes a feature for integrating the energy peaks obtained by pulse height analysis.

Jan 1, 1970

By William H. Schiffbauer

One of the safety and health research programs of the former U.S. Bureau of Mines Pittsburgh Research Center was the evaluation of technology that will provide remote-controlled operation of mechanized equipment in underground room-and-pillar mining. The purpose of this effort was to enable workers to be located away from the hazardous and unhealthful coal extraction area (the face). As part of this program, advanced machine navigation and control technologies were developed for underground room-and-pillar and highwall coal mining that can be applied to commercially available mining equipment. These technologies use off-the-shelf components and a flexible control software architecture to minimize the effort required to adapt them to mining equipment. An accurate, reliable navigation system that can provide the mining machine's heading and location is a critical requirement for a remote-controlled mining system. After investigating several different types of navigation sensors, researchers selected the Honeywell Ring Laser Gyro Inertial Navigation System (INS) as showing the most promise. It was installed on a continuous mining machine at our Mining Equipment Test Facility. Extensive testing at an open pit (OP) site was also performed. This report describes the INS as it was employed on the mining machine in the laboratory, in the field, and OP tests, and provides the accuracy and performance results of the OP and highwalltests.

Jan 11, 1997

By Kay E. Goldberg

The Bureau of Mines conducted a study to develop and evaluate a training workshop for mine safety training personnel. The workshop was based on the Instructional Development Institute (IDI) which has been used for nearly ten years to train educators and administrators in the application of a nine-step model for defining, developing, and evaluating instruction. The Mining Instructional Development Institute (MIDI) was developed by investigators at the University of Southern California as a two-phase project. Phase I involved the modification of the six-day IDI program (including audiovisual presentations, workbooks, games, and exercises) for use by mine safety trainers as a workshop lasting three and one-half days. Phase II involved the evaluation and validation of the prototype MIDI workshop by means of a two-stage jury of experts and a prototype field trial. On the basis of data collected in the validation process it was determined that the institute provided an effective and useful method of instruction in mine safety training and that the institute would be especially valuable for mine safety training administrators and supervisors.

Jan 1, 1980

Surface mining and reclamation of a southeastern Ohio site with sandstone-shale overburden resulted in (as compared to premining levels): 1) runoff volumes and peak rates that increased by a factor of from 2 to 10 during mining and after reclamation, 2) destruction of the "aquifer" perched on the underclay of the mined coal bed and gradual, but, as yet incomplete redevelopment of this aquifer after reclamation, 3) no immediate effect on another, lower perched "aquifer", 4) up to 100 times greater sediment concentrations in runoff. Results were influenced by increasing annual precipitation amounts through the period of record; 1978, 1979, and 1980 (postreclamation years) experienced precipitation amounts approaching or exceeding long-term normalcy for the area. Part of the reason that the site produced more runoff after reclamation than before mining is that the premine condition was one of an open, porous soil under woodland, while the postreclamation condition was one of a compacted, bulldozed soil. Sediment concentration results were influenced by failure of the postreclamation erosion control system and by a series of detention reservoirs above the stream monitoring station.

Jan 1, 1983

By Michael J. Beus

This Bureau of Mines report describes the development of load cells for measuring compressive loads in timber and lock-bolt support systems commonly used in. coal; metal, and nonmetal mines Design and evaluation is covered in detail to insure a reliable, accurate, and practical instrumentation scheme. The load cells are relatively inexpensive and adaptable to various size support systems. User-oriented procedures are emphasized, and design equations were reduced to a series of nomographs. Laboratory evaluation, destructive testing, environmental testing, and tests to determine the effect of extraneous loads were conducted. Field performance was evaluated in conjunction with ongoing Bureau projects at a metal mine in North Idaho and a coal mine in Utah. Load cells utilizing a titanium alloy as the cell body and weldable strain gages as the strain-sensing components satisfied the basic design and performance criteria, and with minor design modifications, the load cells can be adapted to many mining applications.

Jan 1, 1974

By G. K. Derby

Five different types of drilling systems were developed under the flexible drill program that was initiated by the Federal Bureau of Mines to protect roof bolter operators. The systems were designed for underground coal mines with seams as low as 30 inches, and with roof bolts longer than the height of the seam opening. Four of the developed systems were true flexible drills; the fifth was a remote-controlled, automatic rod changer concept. Only two of the five firms successfully completed testing requirements under the original contracts: BendixCorp.,4 with a true-flex drill; and Ingersoll-Rand Research, Inc., with the rod changer concept. The Bendix drill was rated best, and the Ingersoll-Rand drill was rated second. Because of the closeness of the ratings and the vast differences in the two development concepts, both systems had sufficient potential to justify further development funding for design updating and testing. Also, both systems warranted consideration for inclusion into other ongoing development projects under both safety and energy directed programs.

Jan 1, 1978

By John R. Bradley

The object of this paper is to survey and analyze the bearing of economic nationalism, competitive sources of energy, and technologic developments on international trade in coal with especial reference to the competitive position of the leading coal-exporting countries in the Italian market, the largest in the Mediterranean region, and the Brazilian market, the second largest in Latin America. The political, economic, and financial disturbances caused mainly by the World War have resulted in an amazing situation. Especially since 1930 have conditions been complicated.

Jan 1, 1936

By John E. McCullough

The purpose of this development program is to design and develop a known volume air sampling pump for use in measuring the amount of radio-active material in the atmosphere of an underground uranium mine. The principle nuclear radiation hazard to underground uranium mines comes from the mine atmosphere. Daughter products of 222-radon, namely 214-polonium, 214-lead, 214-bismuth and 214-polonium, are inhaled by the miner, resulting in a relatively high lung cancer rate among these workers.

Jan 1, 1976