Search Documents

The Bureau of Mines found sulfur hexafluoride (SF6), released from a lecture bottle, to be an ideal gaseous tracer for studying mine ventilation systems. Air samples were collected in glass syringes and analyzed by electron-capture gas chromatography. In these studies, the lower limit of detection was about I part per billion by volume (ppb) of SF6 per part of air. Experiments conducted in a Pennsylvania limestone mine showed this technique useful in evaluating the effectiveness of auxiliary fans, measuring low flow velocities, probing the air circulating near a working face region where ventilation appeared to be poor, and estimating volumetric flow rates in airways of large cross-sectional area and having low flow velocities. This technique was also used in a western vein-type metal mine to measure the amount of return air being recirculated into the intake air due to leakage through old stoped areas.

Jan 1, 1974

By E. J. Gleim

The importance of "good voltage," especially for direct-current systems in coal mines, is not always fully appreciated. From the practical aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

By Laurance L. Oden

The Bureau of Mines is developing nickel catalysts for converting synthesis gas derived from coal to synthetic natural gas. The present report describes the relationship between the composition of aluminum-nickel alloys in the composition range NiAl3 to Ni2Al3 equilibrated at 840° C and the properties of catalysts obtained from them. Methanation activity was determined in the temperature range of 300° to 360° C in a flowing gas stream containing 1 pct CO, 8 pct H2, and the remainder He. One part per million of H2S was added to the gas stream at 400° C to evaluate the susceptibility of catalysts to sulfur poisoning. The total surface area was measured by the adsorption of nitrogen at liquid nitrogen temperature, and the active surface area was measured by the adsorption of hydrogen at room temperature. Total surface area and active surface area were found to increase with increasing proportion of aluminum-saturated Ni2Al3 in the precursor alloy, but methanation activity and resistance to poisoning by H2S were nearly constant. However, the methanation activity of the catalyst prepared from stoichiometric Ni2Al3 was less than half that of the other catalysts.

Jan 1, 1978

By Terry R. Neumann

In 1989, the Bureau of Mines conducted a mineral resource investigation of the 52,350-acre Jersey Jack study area, located in the Clearwater Mountains of north-central Idaho. Twenty-eight mines and prospects were examined, and 483 rock, placer, and petrographic samples were collected during the field study. Two properties contain gold resources; mining company data show the Robinson Dike mine contains an estimated 940,000 tons of "drill proven and probable reserves" averaging 0.041 oz/ton gold, and the Bureau of Mines investigation showed the Blacksand placer mine contains an estimated 64,000 cubic yards of identified placer resources averaging $8.13 in gold per cubic yard. Sample analyses from other properties indicate that gold resources are likely to exist; however the low tonnage, narrow, fissure-vein type deposits would require mining by relatively high-cost underground methods and would be subeconomic at a gold price of $400/oz.

Jan 1, 1991

Mineral production was of little significance in the country's economy, and Bangladesh was not a world-ranked producer of any mineral commodity during 1977. Natural gas was the most important mineral exploited; however, reserves were sufficient to allow for much greater production, Economically, Bangladesh made some progress in 1977-782 in its struggle against poverty, underdevelopment, and rapidly increasing population. The gross domestic product (GDP) grew 8%, mainly owing to a 13% increase in food grain production, the key economic indicator in this highly agricultural nation. GDP at current prices dropped slightly in Fiscal Year (FY) 1976.77 to $6.6 billion3 and rose to $7.2 billion in FY 1977.78. The population rose from 81 million in FY 1975-76 to about 85 million in FY 1977-78, resulting in an increase of per capita GDP from $83 to $85 during the same period. The high annual population growth rate, over 3% in 1976 and about 2.8% in 1977, was recognized by the Government as the main problem facing the country. Average density was 525 people per square kilometer. A similar density would have the entire world population living within the continental United States.

Jan 1, 1981

By V. R. Spironello

The Bureau of Mines is involved in research directed toward the conserva¬tion of important raw materials and the utilization of solid waste. Two of the objectives are to conserve high-quality coking coals used for foundry coke and to utilize waste materials of marginal quality but of high calorific value. These objectives are consistent with Bureau goals. Pilot plant cupola trials were made to evaluate the adequacy of various alternative fuels, and to determine to what extent they could replace the foundry coke in cupola charges. Information was obtained on furnace performance, metal and slag chemistry, environmental questions, and the properties of castings. It was shown that anthracite or bituminous coals can partially replace charge coke up to the 40 pet level. Briquetted materials prepared from fuel fines, and waste prod¬ucts or byproducts of high calorific value, all tend to break down on heating in a cupola so that their use must be restricted to below 20 pet replacement. In cases where pitch-bonded coal fines or petroleum coke were used, carbon pickup by the iron was inadequate for gray iron specifications. Although emphasis during this work was placed on basic slag practice, some acid practice results are included.

Jan 1, 1980

By Wilton Johnson

Native asphalt was produced in 1982 by five companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by White Uvalde Mines and by Azrock Industries, Inc., Uvalde County, Tex. Historically, gilsonite, a solidified hydrocarbon found only in Utah and Colorado, had been mined by American Gilsonite Co. and by Ziegler Chemical and Mineral Corp. from properties near Bonanza, Uintah County, Utah. During 1982, Hydrocarbon Mining Co., a subsidiary of the Oberon Oil Co., entered into a joint venture with Miocene Resources Inc. of Novato, Calif, to form Hydrocarbon Resources Co. for the purpose of mining gilsonite about 50 miles south of Vernal, Uintah County, Utah. Under the agreement, Hydrocarbon Mining contributed gilsonite-bearing properties held by lease or sublease as well as mining equipment to the venture. The property contained leases totaling 760 acres with probable reserves of 268,000 tons of gilsonite. Miocene Resources provided the partnership with a minimum of $200,000 to develop two of the leases and were to be responsible for management of the mining operations.2

Jan 1, 1983

By D. J. Parker

On Thursday, March 18, 1937, the country was shocked by news of a terrific explosion at the New London, Tex., school, which caused the death of 280 pupils rind 14 teachers. The explosion occurred at about 3:05 p.m. in the largest of the 11 school buildings on the campus. Figure 1 shows this building, market; "Main high school building?, with respect to other buildings, pipe lines, oil wells, and gas lines on the property.

Jan 1, 1937

By H. P. Greenwald

About mid-December 1936, the safety director of a large coal corporation visited the authors at the Bureau's Experimental coal mine to discuss a rock-dust barrier he had invented primarily for use in trackless entries of coal mines. The rock dust in this device was carried in its original paper containers and means were provided for ripping these open so that the dust might be scattered in the path of an explosion. The inventor termed the device a "bag barrier", and this term has been adopted in the present paper for convenience. At that time the device was in an early stage of development, and the inventor felt that the barrier should be tested to determine whether it had enough promise of being successful to justify further development. The matter was taken under consideration and finally three tests were made during the week of February 15, 1937. It was concluded that while the device did stop an explosion in two of the three tests, it was much loss effective than ordinary rock dusting, and that too few data were obtained to permit direct comparison with tests of other barriers. Apparently, the conditions under which the device could, be successful were somewhat limited, out the limits could not be defined without additional tests.

Jan 1, 1938

By E. R. Maize

[?he scconG rcport of :his st?rI.org 8cdt with o3servatioi:s of conver- gence of roof an4 floor at t!x*re: ?.cc.-.tioris iri til~ ClVucible mine of kke Cru- cib1.o Fuel Co. Data on sl:'ociacnce ?.rd Lztcrcl mwe:~cnt cf the surface were .:lven for two of these areas, cnS it was mentioned that ~lr~~ilar data were being obtained on a ?art of Pe:sc:rlvtzr.ia Fii~l?trr.y FE:, ~i!lic;l pcser: over the third area. 'I'hie hichwc :LEO FasseE over t!lc ITenncoli::. :.line of the Bnckeye Coal Co. 9 milcs to ';he so-lth, cnd at P. l~tcr C'..att: ~.nr?r.,cc?r:cntS *.rere mnd.e to make similar observati on3 there. This y: pr mrnmri:.c n Czto obtnino? at those two locetionn,]

Jan 1, 1941

By Robert S. Schechter

This report describes the development and application of PHASEQ/FLOW, a geochemical flow simulator capable of describing the dynamic changes in chemical composition of an aqueous solution during flow in a permeable medium. The solution components can react through intraaqueous reactions, redox, precipitation, or dissolution. The assumption of local thermodynamic equilibrium ensures maximum generality with respect to the number of species and components possible; however, the fluid flow itself is limited to one-dimension. The report describes several applications: generic batch equilibria, flowing equilibria, uranium roll-front deposition, and roll-front leaching.

Jan 1, 1985

By C. H. Fisher, M. L. Fein, A. Eisner, G. C. Sprunk, Loyal Clarke, H. H. Storch

"The large reserves of low-rank coals in the western United States are at a disadvantage in competing with the more mature but less plentiful eastern coals, which are nearer important markets and are more suitable for combustion and coke production. However, low-rank coals generally are amenable to hydrogenation, and the western coals might become an important source of liquid fuels and organic chemicals when petroleum is less plentiful.In view of these facts an the tremendous quantities available, further information on the western coals clearly desirable. The purpose of the work described in this paper was to study the hydrogenation characteristics of some of the low-rank western coals in discontinuous converters. The data obtained in this manner, which are inadequate for predicting the suitability of coals for large-scale continuous hydrogenation, were used as a basis for selecting samples for further study in the Bureau's experimental coal-hydrogenation plant (26, 35). 8/ Because of the general importance of the western coals and recently demonstrated relation between coal hydrogenation and petrograghy (14, 15, 16), the proportions of anthraxylon, (vitrain), translucent attritus, and opaque matter were determined. In some instances samples of anthraxylon were isolated and hydrogenated separately so that their properties might be compared with those of the entire coal. The samples studied include peat, brown coal, lignite, sub-bituminous coals, and low-rank bituminous coals."

Mar 1, 1940

By Frank E. Chase, Deno M. Pappas, Christopher Mark

Multiple seam interactions are a major ground control hazard in many U.S. underground coal mines. The two most common types are: • Undermining, where stress concentrations caused by previous full extraction in an overlying seam is the primary concern, and; • Overmining, where previous full extraction in an underlying seam can result in stress concentrations and rock damage from subsidence. The National Institute for Occupational Safety and Health (NIOSH) has completed a major study aimed at helping to identify the location and likely severity of these interactions. In the course of field visits to mines throughout the U.S., more than 300 multiple seam case histories were assembled into the largest data base of multiple seam case histories ever collected. These data were analyzed with the multivariate statistical technique of logistic regression. The study also employed LaM2D to estimate the multiple seam stresses, ALPS and ARMPS to determine pillar stability factors, and the CMRR to measure roof quality. The study resulted in the development of a computer program, called Analysis of Multiple Seam Stability (AMSS), which can help mine planners to evaluate each potential interaction and take steps to reduce the risk of ground control failure. AMSS first evaluates pillar design by calculating the single seam Stability Factor (SFSS) using ALPS or ARMPS. It also automatically generates a LaM2D analysis that provides the additional multiple seam stress so that the final, multiple seam SFMS can be determined. The second part of the AMSS procedure builds upon the statistical findings that overmining is much more difficult than undermining, isolated remnant pillars cause more problems than gob-solid boundaries, and weaker roof significantly increases the risk of multiple seam interactions. AMSS quantifies these effects and predicts the outcome in terms of three levels of risk: GREEN (where a major multiple seam interaction is considered unlikely), YELLOW (where adding a pattern of cable bolts or other equivalent supplemental support could greatly reduce the probability of a major interaction.), or RED (a major interaction should be considered likely, and it may be desirable to avoid the area entirely).

By Glan Dale Coe, Will H. Coghill

"INTRODUCTION Characteristics of the mineral products that are to be contrasted herein are net energy consumed in grinding to a definite top limiting size and size distribution of the ground products. Through contrasts of these grinding characteristics this paper to differences in related mineral products and in unlike products. For,example, in anticipation of the data to follow, although Joplin chert and Babeitt taconits are running mates in defying the best crushing machinery, taconite is one of the more docile and Joplin chert one of the most refractory mineral products ordinarily fed to a grinding Routine grinding tests on a great variety of ores and tabulation of the findings have been covered amply by Lennox 4/ and by Maxon 5/ and associates. In contrast to that work, the present paper is a record of random tests made over a long period, and each answered an urgent question at the moment. The work was done at the Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama. The pressure of war work prevented an organized investigation."

Apr 1, 1943

By C. E. Dobbin

The coal fields of Montana are widely distributed through the plains region in the eastern and northern parts of the State, and the mountain regions in the central, southern, and southwestern parts of the State. (See fig. 1.) SURFACE FEATURES The Fort Union region in eastern Montana is a broad plain of almost horizontal rocks, characterized by extensive "bad lands" along the larger streams and by red hills, benches, ridges, and buttes which represent shale and sandstone that have been fused by the burning of an underlying coal bed.

Jan 1, 1932

By Stephen R. Iverson, Bill M. Stewart, Michael J. Beus

The U.S. Mine Safety and Health Administration (MSHA) has identified ore pass hazards as a significant safety problem in underground metal mines in the United States injury and fatality data show that many injuries are related to pulling or freeing ore pass chutes and structural failures of control gates and ore pass walls. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating these hazards and developing methods to improve safety during transport of ore and waste. Particle flow analysis methods were used to simulate chute and control gate response to various material loading scenarios. Results from computer models indicate that dynamic impacts from ore and waste rock might be considerably greater than theory predicts. Static and dynamic loads were measured in a laboratory setting using scaled ore (sass mock-ups. Field tests were initiated in an active ore pass to determine actual static and dynamic loads. Field data were compared to computer results and indicated that impact and total static loads were substantially less than the computer model results suggested. Damping factors, normal and shear stiffness, and mass frictional characteristics have a significant effect on particle flow and resulting impact loads.

"U.S. Bureau of Mines Publications and Articles, 1994 with Subject and Author Index Compiled by Office of Public Information U.S. Bureau of Mines (USBM) Department of the InteriorINTRODUCTIONThe U.S. Bureau of Mines (USBM) was established in 1910 to conduct inquiries and scientific and technological investigations on mining and the preparation, treatment, and use of mineral substances; to promote health and safety in the mineral industries; to conserve material resources; to promote economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau of Mines to ""disseminate information concerning these subjects in such manner as will best carry out the purpose of this Act.""In accordance with this directive, USBM reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-USBM publications. This edition describes reports and articles published during calendar year 1994. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960; 1 the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960; 2 andthe 5-year lists of publications and articlesfrom January 1, 1960, to December 31, 1964,3from January 1, 1965, to December 31, 1969,4from January 1,1970, to December 31,1974,5from January 1,1975, to December 31,1979,6from January 1,1980, to December 31,1984/and from January 1, 1985, to December 31,1989.8"

May 1, 1995

By J. G. Kirby

The total number of petroleum refineries in the United States continued to decline during 1950, and according to the Bureau of Mines annual refinery capacity survey there were 357 refineries January 1, 1951, compared with 367 a year ago. The total throughput capacity increased 267,344 barrels daily during the year to 6,963,644 barrels daily as of January 1, 1951, continuing the trend of the past several years to increase the throughput capacity of the refineries and decrease the number of plants. The capacity of the average refinery to process crude oil increased during 1950 from 18,246 barrels daily to 19,506. The Indiana-Illinois refinery district accounted for 110,175 barrels, or 41 percent of the total crude-oil capacity increase, the Oklahoma-Kansas district, 17 percent, the California district, 14 percent, the East Coast district, 13 percent, and the Louisiana Gulf Coast district, 12 percent. Slight declines ill crude-oil capacity were reported in the Texas Inland, Texas Gulf Coast, New Mexico, And Appalachian refinery districts. The 160,100 barrels of additional crude-oil capacity that was building January 1, 1951, represents an increase of 10 percent over the year earlier figure. The only completely new refinery listed as under construct ion at the beginning of 1951 is located at Superior, Wisconsin. Other new construction involves enlargement of existing refineries. Plans for at least five additional new refineries are under consideration, and construction is expected to begin during the current year.

Jan 1, 1951

By G. R. Hopkins

Crude-petroleum pipe lines in the United States on May 1, 1941, had a total length of 118,350 miles - an increase of 7,770 miles since Jun, 30, 1936, then the last previous survey was made by the Bureau of Mines. The expansion was due almost entirely to trunk-line construction, as the mileage of gathering lines was virtually unchanged from 1936. The greatest mileage of gathering lines, 53,640, was recorded in the survey of May 1, 1931. Both trunk and gathering-line mileage decreased moderately, in the interval from 1531 to 1936, but the present survey indicates that trunk-line facilities have expanded since 1936 to new high levels. Truck-line mileage equaled 55 percent of the total mileage of all crude lines on May 1, 1941, and 52 percent is 1936. The total length of gasoline pipe lines on May 1, 1941, was 9,001 miles this does not include several hundred miles of life under construction at that time or several hundred additional miles now being laid. No detailed surveys of gasoline mileage were made for 1, 1931, and June 30, 1936, but the mileage for those dates was about 1,400 and 4,600, respectively.

Jan 1, 1941

By A. E. Raddatz

The Federal Bureau of Mines, as part of its goal to minimize undesirable environmental impacts associated with mineral processing, has investigated a soda-smelting technique for processing ilmenite into pig iron and a titanium slag that is suitable for a feed to a sulfate-process titania pigment plant. By this procedure, the generation of ferrous sulfate waste and its associated disposal problem is obviated. Molten titania slag was quenched, water leached, and filtered to yield a sodium titanate intermediate product containing about 70 wt-pct Ti02, 1 wt-pct Fe, and 20 wt-pct Na20. This intermediate product, high-soda titanate (HST), was mixed with H2S04, calcined, quenched, and water leached to produce a low-soda titanate (LST) product that contained only 2 wt-pct Na20. Both the HST and LST were evaluated as feed materials for preparing titania by the sulfate process. About 95 pct of the Ti02 was extracted from HST and LST by digestion in concentrated or 50-wt-pct-H2S204 solutions. About 95 pct of the solubilized Ti02 was subsequently recovered from the titanyl sulfate solutions by hydrolysis. Barren solutions from hydrolysis, containing about 26-wt-pct H2S04, were upgraded by vacuum-thermal evaporation or electrodialysis. The regenerated acid solutions were used to digest additional HST and LST.

Jan 1, 1979