Search Documents

By Phillip M. Busch

VANADIUM was discovered in 1801 by Andres Manuel del Rio, a professor of mineralogy at the School of Mines in Mexico City. Del Rio called the new element erythronium. Later, he decided that this was not a new element but a form of chromium. Not until 1831 did Nils G. Sefström, a Swedish chemist, positively determine that the metal was a new element which he named vanadium, after Vanadis, the Scandanavian goddess of beauty. From 1831 to the 1860's and 1870's, the comparative scarcity and high cost of vanadium restricted its commercial use. Shortly after 1870, more information was obtained on the physical and chemical properties of the element. Thereafter, research on vanadium has dealt largely with its use as an alloying element in steel and nonferrous metals. Vanadium is a widely distributed element in the earth's crust. It is more abundant than many metals but is disseminated in small quantities throughout a great variety of rocks. Relatively few deposits have contained ore of a grade suitable to warrant development for vanadium alone. It is produced in conjunction with uranium, iron, titanium, aluminum, and lead-zinc ores.

Jan 1, 1961

By P. D. Kovscek

The Bureau of Mines equipped a longwall shearer with a water-jet-assisted mechanical cutting system to determine the effect of the high-pressure sprays on machine performance, airborne dust levels generated, and size of particles formed. Testing was conducted on a simu-lated coal block (coalcrete) while cutting at a water pressure of 190 psi and at water-jet-assisted pressures ranging from 1,000 to 6,000 psi. The shearer motor energy used by the shearer while cutting coalcrete was determined for each cutting condition. Results indicate that the motor energy required by the shearer for each ton of material cut did not vary significantly as the water pressure was increased. Results of dust measurements recorded near the cutting drum indicate that at water pressures above 3,000 psi, dust reductions up to 85 pct were achieved com-pared with cutting with conventional sprays. Analysis of the particle size distribution during cutting showed that increasing the water pres-sure resulted in increased median particle size. In light of these results, various mechanisms for water-jet-assisted cutting are discussed.

Jan 1, 1986

By S. M. Shelton, M. M. Fine, T. L. Johnston

"INTRODUCTION The Bynum property is about 15 miles west of Gadsden and 1 mile north of Walnut Grove, Etowah County, Ala. The ore lies in layers and as irregular masses and pockets in the clay residue from decomposed quartzite and limestone formations to the district.The property has been developed by means of numerous shallow shafts sunk to water level - about 25 foot. Operations are confined to small-scale, selective mining of pockets of high-grade ore. The ore is marketed directly, without beneficiation. The property does not yield a large amount of manganese ores. No estimates of reserve ore tonnages are available.A 206-pound sample was furnished for test. It was taken at random from a stock rile estimated to contain 130 tons of ore. The sample con¬sisted of a mixture of manganese oxides, iron oxides, and siliceous fragments in clay. The manganese occurred largely as soft, unconsolidated pyrolusite and wad. Some hard, crystalline pieces of psilomelane were distributed through the soft material. Small amounts of iron oxides were associated with the manganese oxides. Chert, quartzite, and clay comprised the gangue minerals.Dry analysis of the sample was as follows: 36.0 percent manganese, 6.1 percent iron, 2: .0 percent silica, 1.5 percent calcium carbonate, 0.36 percent phosphorus, 3.0 percent alumina, 2.2 percent barium, and 0.31 percent zinc."

May 1, 1942

By J. E. Shelton

Flotation tests are described on samples of two lowgrade nickeliferous ores of Oregon and Washington. The sample from the Congress mine, Ferry County, Wash., contained 1.2 percent Ni, occurring chiefly as millerite. The sample from the Shamrock mine, Jackson County, Oreg., contained 2.20 percent Ni and 0.78 percent Cu occurring chiefly as pentlandite, nickeliferous pyrrhotite, and chalcopyrite. The millerite in the Congress ore was concentrated by flotatioin with aulfydric collectors in a series of locked tests to recover 73 percent of the nickel as a 7 percent bulk concentrate. By successively regrinding and floating the bulk concentrate, it was further concentrated to 12.4 percent Ni at a recovery of 59 percent and 21.8 percent Ni at a recovery of 50 percent. Attempts at selective concentration of the copper-nickel Shamrock ore were only partly successful because of the intimate association of pentlandite and chalcopyrite. The nickel concentrate, which contained 86 percent of the nickel, had an analysis of 4.42 percent Ni and 1.03 percent Cu. The copper concentrate had an analysis of 18.8 percent Cu and 1.96 percent Ni and contained 48.5 percent of the copper. A bulk sulfide concentrate contained 92 percent of the copper and 01 per¬cent of the nickel and had an analysis of 4.17 percent Ni and 1.63 percent Cu.

Jan 1, 1956

By J. L. Hoffman, F. W. Wood, R. A. Beall, W. E. Anable

For melting and purifying reactive and refractory metals , two electronbeam furnaces have been constructed and operated on the principle of highpowered vacuum diodes . It was necessary to design the vacuum and electrical systems , mechanical features , and operating procedures to cope with dynamic conditions . Vacuums of 10-5 torr , tens of kilowatts of power at 5 to 10 kilovolts , and the evolution of impurities at thousands of liters per minute constitute a challenging combination . The furnaces have been used to melt either button specimens weighing several hundred grams or , by feeding material as a consumable electrode , small ingots weighing several kilograms . Hafnium is among the metals that can be purified . For example , hafnium starting material with Rhn 94B was softened to Rhn 70B after 2 hours of melting under a 25 - kw electron beam , and impurity levels were reduced as follows : Oxygen , from 700 to 350 ppm ; nitrogen , from 71 to 20 ppm ; hydrogen , from 6 to 1 ppm ; aluminum from 75 to < 20 ppm ; chromium , from 80 to < 10 ppm ; iron , from 100 to 40 ppm ; and silicon , from 40 to < 20 ppm .

Jan 1, 1963

By Bolmerm R. L.

This information circular describes the application of modern methods and equipment in sinking a vertical, 916-foot-deep by 16-foot-diameter, concrete-lined access shaft for the Harold D. Roberts tunnel near Montezuma, Colo. Although the access shaft was merely a construction facility to expedite completion of a 23-mile water-diversion tunnel, a circular shaft of this type would be equally adaptable for mine development or other purposes. Comparable sinking methods and equipment could be used for similar shafts within a wide range of sizes and depths. SUMMARY In addition to excavation and support of the basic access shaft to tunnel grade, the overall sinking project involved initial preparation of a surface site and plant, subsequent construction of a tunnel-level station and loading pocket at the shaft bottom, and ultimate conversion of the basic shaft into a hoisting and access facility for tunnel operations. The sinking period for the basic shaft approximated one year. Actual tunnel operations through the converted shaft began on April 3, 1958, approximately 19 months after the project was initiated.

Jan 1, 1961

By Melvin E. Poad

This Bureau of Mines report presents two phases of a research program to evaluate a single-entry system for longwall development. Organizations participating in the program; which began in July 1971, include the Bureau of Mines, the Mining Enforcement and Safety Administration, and the University of Utah, working under a cooperative agreement with Kaiser Steel Corp. at its Sunnyside mine in Utah. Part 1 of this report describes the present longwall mining practice, including a brief history, and discusses the advantages and disadvantages of a single-entry development system and its introduction in the United States. Part 2 of the report presents the research program; test design, instrumentation for ground and support evaluation, and the test results from the No. 2 mine. Subsequent reports will describe the research conducted in the No. 1 mine.

Jan 1, 1977

By C. W. JEFFERS

At its annual meeting on March 5, 1928, in Washington, D. C., the Joseph A. Holmes Safety Association gave to the Ford Collieries Co., Curtisville, Pa., a certificate of honor for "having worked 922,628 underground man-shifts from August 14, 1920, to December 31, 1926, producing 5,755,669 short tons of coal without a fatality." This remarkable record certainly deserved recognition. It developed that this company's freedom from fatalities continued until October 2, 1929, hence the full period during which no underground fatalities occurred was from August 14, 1920, to October 2, 1929, or 9 years, 1 month, and 18 days, the total tonnage being over 7,700,000. Table 1, shows the complete safety record of the Ford Collieries Co. since 1920 as given by the officials of the company. The first item in Table 1 shows a remarkable performance. This company since 1920 has mined 15 times more coal per fatal accident than the average pro- duction per fatal accident for the State of Pennsylvania in 1928 (255,257 tons). Excluding the two fatalities (one in 1922 and one in 1929) the severity rate for the same period has been 1.259 per thousand hours worked, a record of which the company may justly be proud. However, including the fatal accidents the rate is 2.407. This compares favorably with an average of 12.4 in 1928 for 66 mines in the National Safety Competition. The Ford Collieries Co. operates three mines located in the vicinity of Curtisville, Allegheny County, Pa. One of these mines, Benjamin No. 1, is idle at the present time. The officials are: A. R. Pollock, general manager, Curtisville, Pa., and C. W. Pollock, assistant general manager in charge of safety and operation.

Sep 1, 1930

By R. C. Hickman

"INTRODUCTION Marl, consisting of a bed of coarse shell conglomerate from 1 to 5 feet thick, occurs on the Chesapeake Corporation tract and Philbates properties in New Kent County, Va.Nine holes were drilled on these properties in February 1946. ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts prelimi¬nary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.The project was under the immediate supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch.LOCATIONThe Chesapeake Corp. deposit is reached from West Point, Va., by driving west on State Route 33 to the junction of State Route 634, approximately 5 miles. Proceed southeast along State Route 634 about three-quarters of a mile, at which point an old longing road turns north along a ridge and leads to the marl outcrops about one-half mile distant. The Philbates property lies three-quarters of a mile farther west along State Route 33 from the junction with State Route 634. The property lies north of State Route 33 and east of State Route 623 (fig. 1). The marl deposits are on the north end of the farm. The Chesapeake Corp. tract comprises 174 acres and the Philbato property 58 acres."

Aug 1, 1947

By Frank E. Cash, Max S. Petersen

The use of safe equipment, safeguards, and safe practices in the mining and allied industries should reduce injuries and improve accident experience. The object of this report is to give to the mining industry, especially metal mining, a graphic pictorial description of some of the safeguards, equipment, and practices used and followed in the iron-ore mines of the Lake Superior district. Some of the subject material has been in use or has been established for many years, and some is relatively new. Some of the equipment was purchased commercially, and some was designed by the company employees and constructed in the mine shops. The photographs were taken by the personnel of the Health and Safety Division of the United States Bureau of Mines, primarily for use in the Metal-Mine Accident-Prevention Course of the Bureau of Mines. In general, they are arranged under the following headings or subjects: 1. Accident statistics. 2. Support of ground. 3. Hoisting and haulage. 4. Explosives. 5. Fires, gases, and ventilation.

Oct 1, 1948

By Lowell B. Moon

Concern over possible wartime shortages finally resulted in passage of the Strategic Materials Act in 1939. As authorized by one section of this legislation, the Bureau of Mines proceeded to investigate deposits of seven strategic minerals with the objective of developing tonnages of low-grade material that could be mined in an emergency. During the war, the size of the program and the number of strategic minerals were increased, and the objective was the more immediate one of aiding production. Since the war, the size of the program has been reduced, but the number of minerals on the strategic list continues to be large. The objective has returned to that of 1939. In the course of the program, more than 10,000 examinations were made and about 1,300 projects were run on deposits of 33 different commodities. A considerable contribution to war production was made in six of the commodities investigated, and a minor contribution was made in twelve others. Substantial reserves have been indicated in 19 minerals. Private interest is currently active in some of the deposits developed in 14 commodities.

Jan 1, 1950

By Yael Miron

The presence of pyrite (FeS2) in coal can cause or contribute to several problems for the coal mining industry. These problems, which include spontaneous combustion, roof falls, floor heave, and accidental explosions in coal surface mining when ammonium nitrate fuel oil (ANFO) explosives are used, result from pyrite oxidation. Pyrite oxidizes exothermically in the presence of air and moisture to form a large variety of products, including hydrated ferrous and ferric sulfates, and sulfuric acid. Some of the products are reactive chemicals and strong oxidants. The volume of many of these oxidation products exceeds the original volume of the pyrite; as a result, the adjacent coal disintegrates and its surface increases, rendering it more susceptible to oxidation. The heat from pyrite oxidation raises the temperature of the adjacent coal, accelerating the oxidation and self-heating rates of the coal. These combined chemical, physical, and thermal effects are the cause of the aforementioned problems. When ANFO is used in surface coal mines and contacts ferrous sulfate, a highly exothermic reaction ensiles. Additional hazards are fires or explosions caused by the frictional ignition of methane when the pyrite in the coal is struck by a cutting bit during mining.

Jan 1, 1994

By H. W. Kilau

The Bureau of Mines tested chromium-bearing waste slags from industrial stainless steel and other chrome alloy operations to determine their chromium leachability characteristics under acid precipitation conditions and to devise measures to prevent any pollution originating from this source. Two critical slag composition factors were found to control the chromium leachability: (1) CaO:Si02 ratio and (2) magnesium content. Above a 2.0 CaO:Si02 ratio, chromium exists in slag as CaO·Cr203, which can be vulnerable to leaching by acid precipitation especially if oxi-dized to CaCr04 when exposed to the environment over an extended period. Maximum chromium leachability from industrial slags occurred when the composition of the slag had about a 2.0 CaO:Si02 ratio. Between a 1.0 and 2.0 CaO:Si02 ratio, in the presence of sufficient magnesium, MgO ·Cr203 was formed, which is very resistant to oxidation and to dissolution by simulated acid precipitation. Addition of magnesium silicates to molten slag to fix the chromium in the MgO·Cr203 form was successful in preventing chromium leaching in simulated acid rain solutions. Experiments showed olivine and waste taconite tailings were suitable for this purpose. Olivine addition to a waste slag having a composition vulnerable to leaching (CaO:Si02 > 2) reduced the chromium leachability more than 80 pct.

Jan 1, 1984

By George L. Gates

The Bureau of Mines studied pressure-buildup data from a number of California gas wells to determine if the reservoir properties calculated from these data correlated with field-observed reservoir properties. Pressure-buildup curves from 24 wells showed distinct changes in slope, indicating changes in permeability of the reservoir rock. Calculated distances from the wells to indicated permeability changes were in fair agreement with distances deter-mined in the field. Pressure-buildup curves from three wells had more than one distinct change in slope, indicating multiple permeability changes. Thus field data supported the theoretical relations used to calculate reservoir properties from pressure-time relations measured in gas wells.

Jan 1, 1967

By P. B. Altringer

Searles Lake, CA, contains the largest known domestic tungsten resource. The brines in this near-dry lake bed, located in the Mojave Desert 130 mi northeast of Los Angeles, contain an estimated 135 MMlb of tungsten. However, the low concentration of tungsten (0.080 g/L W03) in the supersaturated brine makes selective tungsten extraction very difficult. Although many brine chemicals are extracted from the lake, tungsten recovery was an elusive goal prior to Bureau of Mines development of an ion-exchange technique. This publication describes the Bureau process. The following subjects are ad-dressed: ? The Searles Lake tungsten resource. ? General problems associated with tungsten recovery. ? Bureau research objectives. ? Synthesis of ion-exchange resins. ? Development of a two-stage ion-exchange tungsten extraction and concentration procedure. ? Product recovery and purification. ? Economic evaluation. Flowsheets for recovering three products (calcium tungstate, sodium tungstate, and tungstic oxide) are presented and evaluated, as well as a summary of the research effort and potential applications.

Jan 1, 1985

By Clarence A. Wright, JAMES T. NORTON, JAMES G. PARMELEE

The object of this paper is to give to mining companies and to all others who are interested some idea of the possibilities in the treatment, by differential flotation, of lead-zinc ores of the Coeur d'Alene region and other districts. The purpose of these investiga.. tions is not to evolve a differential flotation process that would replace present methods of gravity concentration but rather one that could be applied to the relatively fine material and slime produced in the mills and treated unsuc_pessfully by gravity methods or by flotation. It is expected, of course, that the products to be obtained by differential flotation would be of much better grade than those now produced by flotation in the Coeur d'Alene mills. In view of the fact that it has been difficult to obtain representative samples of flotation feed from the mills, owing to the necessity of shipping the material wet and free from oil or other foreign matter that might be deleterious to the differential separation of the sulphides, the writers have felt justified in running flotation tests with the mill feeds in order to ascertain whether a differential separation of the sulphides could be effected. However, two different lots of flotation feed were tested for differential flotation, and the results of tests of one of these are given in this report. It is hoped that it will be possible later to test out the flotation feed for differential flotation on a large scale in some of the mills. This paper covers part of the investigations carried on by the United States Bureau of Mines in cooperation with the Idaho Bureau of Mines, the University of Idaho, and certain mining companies of the Coeur d'Alene region. Although the results of the tests included in this report are not to be considered final, they indicate possibilities and may suggest others leading to a solution of the problem of separating lead and zinc sulphides by differential flotation in the treatment of certain ores.

Jan 1, 1921

By Mark P. Meyer

This U.S. Bureau of Mines publication presents salient information in abstract form on 247 coal deposits in Alaska. Coverage includes currently producing deposits and deposits that appear to have commercial production potential. Data arc taken from coal properties identified by the U.S. Bureau of Mines minerals availability program and by a literature search. Infrastructural and institutional factors affecting coal development in Alaska are also discussed.

Jan 1, 1987

By G. T. Fisher

The material requirements of carbide cutting tools for machining steel and cast iron are dependent on WC bonded with Co, with additions of TaCand TiC. The Bureau of Mines is conducting research to devise substi-tute materials, based on Ni-alloy-bonded TiC, for C-5-grade cutting tool applications. This substitution would result in less dependence on foreign sources for Co, Ta, and W, and use of lower cost materials. In this preliminary study, the Bureau investigated the effects of composition and processing variables on the transverse rupture strength and hardness of Ni-alloy-bonded TiC to identify compositions that exhibit promising mechanical properties. Further systematic modification of these compositions by soild-solution strengthening additions would subsequently be evaluated to obtain cutting tool materials with requisite properties and performance for C-5 applications. Compositions for evaluation were prepared by a powder metallurgy method of cold-pressing and liquid-phase sintering. Complementary analysis of compositions included chemical analysis, X-ray diffraction, energy-dispersive X-ray spectro-scopy, and density measurements. Based on results of this investigation, promising compositions were determined to be 59.37TiC-25Ni-5Mo-lO.63Mo2C, 59.68TiC-25Ni-3.33Mo-1.77Mo2C-6.67W-3.55WC, and 59.35TiC-25Ni-l.67Mo-3.54Mo2C-3.33W-7.1WC.

Jan 1, 1987

By Roswell W. Prouty

As part of a general plan for control and economic utilization of the waters of the Missouri River Basin as well as development of its inherent power resources, the Corps of Engineers of the United States Army has under construction a rolled earth dam near the site of old Fort Randall in South Dakota. The dam is in Charles Mix and Gregory Counties on the Missouri River at a point about 922 miles above its mouth. It is approximately 125 air-line miles southeast of Pierre and 55 miles southwest of Mitchell, S. Dak. The storage reservoir to be formed by the dam will extend upstream for 150 miles and, at maximum operating pool level, will cover an area of some 107,000 acres. It will have a storage capacity of 6.2 million acre feat.

Jun 1, 1949

By J. H. Holden, C. C. Shale, G. R. Strimbeck, W. S. Bowie

Electrical characteristics are presented for air in a 2 - inch pipe - type electrostatic precipitator operating under dynamic conditions at temperatures of 600 ° to 1,500 ° F and pressures of 0 to 80 psig using a negative discharge electrode . Results of this one - geometry study show that current - voltage relationships are a function of air pressure and temperature and indicate that precipitators can be used at any temperature through about 1,350 ° F over the full range of pressure . Corona starting voltage and sparkover voltage vary directly with pressure and inversely with temperature . At temperatures above 1,350 ° F use of precipitators may be limited to operations at pressures somewhat above atmospheric pressure . Theoretical derivations are presented that relate the effect of gas density on corona starting voltage and the effect of ion mobility on corona current . Deviation from the theory is noted at high current levels . Theoretical discussion is presented to explain the apparent electrical limitations for use of precipitators at high temperature , low gas density , and high corona currents , conditions at which calculated ionic velocities are extremely high . Experimental results are interpreted in terms of the theory presented . 1,500 ° F thermal ionization does not appear to be a critical factor .

Jan 1, 1963