Search Documents

By M. H. Salsbury

This report describes the tunneling at the Leadville drainage tunnel, which was resumed in September 1950 with funds made available in the 1950 appropriation of the Department of the Interior. It brings up to date the account of the first project, carried on from December 1943 to August 1945, published by the Bureau of Mines which supervised both the first and second projects. In this report Leadville mining history, particularly related to drainage efforts, and the possibilities for future mine drainage are discussed briefly. An account of the second project, including a description of the operating cycle, exploratory drilling done as a safety measure, surveying procedures, geology, cost data, and other pertinent information, completes the report.

Jan 1, 1956

By R. P. Walters, M. J. Lynch, D. R. Flinn

The Bureau of Mines evaluated tthhee feasibility of substituting platinum- coated metals for bulk platinum shapes as a means for conserving platinum . Platinum coatings were prepared using four different methods of electrodeposition , then tested and evaluated . In order for platinum coatings to be useful in process environments , they must be thick , adherent , stress - free , and pore - free . The Bureau evaluated direct - current , current reversal , cathode shielding , and pulsed- current plating techniques for producing a pore-free platinum electrodeposit from a molten cyanide bath . Aqueous corrosion tests of Fe - 10Cr substrates coated with approximately 25 μm of platinum showed that pulse plating yielded the most corrosion- resistant and , hence , the most pore -free coatings . The morphology of coating cross sections was in all cases columnar . The average grain size of pulse -plated deposits was independent of thickness , while all other plating techniques produced grains that increased in size as the coatings became thicker . It is believed that the constant grain size in the pulse - plated deposits resulted from better mass transport during the electrodeposition .

Jan 1, 1965

By B. W. Gandrud, G. D. Coe

"INTRODUCTION The Bureau of Mines, United States Department of the Interior, with the cooperation of the University of Alabama and coal producers of Alabama, is making a series of washability studies to obtain technically and commercially important data from the productive coal beds of the State. Based on the system followed in these studies, this report consists of screen-sizing and sink-and-float data on the America and Pratt beds at Gorgas, Ala.SAMPLING AT THE MINESAlthough operations were discontinued in 1929, the accessible openings of the old Gorgas mines of the Southeastern Fuel Co. made possible the taking of samples from the America bed at three openings and from the Pratt bed at two openings. A sample was taken from the America bed at the Klondyke opening; a second was taken about 1 rile south of the Klondyke at the Musgrove America opening, and a third sample was taken about 1-1/2 miles south of the Musgrove-America at the Cricket Lodge opening. A sample was taken from the Pratt bed at Musgrove-Pratt No. 1, which is about 3/4 mile east of Musgrove-America, and a second sample was taken at Musgrove-Pratt No. 2, which is about 3/4 mile west of Musgrove-America. The samples ranged in weight from 1/2 ton to 1 ton and were equivalent to approximately a 2-ton sample from each bed. Figure 1 shows sections of the beds at the places sampled.In addition to the samples for washability study, a seam sample for analysis was taken at each of the places sampled. So as to give a representative seam sample for each of the two beds, these samples were combined in the laboratory in proportion to the thickness of the bed at the places sampled."

Jul 1, 1939

Toward the goal of maximizing minerals and metals recovery from domestic resources, the Bureau of Mines, U.S. Department of the Interior, has conducted in situ corrosion studies at the Salton Sea Known Geothermal Resources Area (KGRA) in the Imperial Valley, Calif., to evaluate and characterize materials of construction for geothermal resources recovery plants. General-, pitting, and crevice-corrosion characteristics of 13 commercially available alloys were investigated for periods of 15 and 30 days in seven process environments expected to be found in typical geothermal resources plants. Stainless steel alloy 29.4, Inconel 625, and the Hastelloys G, S, and C-276 were the most resistant to general corrosion, did not pit, and exhibited little susceptibility to crevice corrosion. Stainless steel alloys 430, E-Brite 26-1, and 6X had low general corrosion rates, but pitted and were susceptible to crevice corrosion. Stainless steel alloy 316 L had a low corrosion rate, but corroded intergranularly, pitted, and was susceptible to crevice corrosion and to stress-corrosion cracking. Titanium-1.5 nickel and TiCode-12 had low corrosion rates, did not pit, and were not susceptible to crevice corrosion. Carbon and 4130 steels had high corrosion rates, pitted, and had high susceptibilities to crevice corrosion. The major scale-forming mineral on the corrosion samples in most of the process environments studied was galena mixed with lesser amounts of other minerals.

Jan 1, 1979

By Milton H. Fies

The dedication of thin building, establishing a station of the U.S. Bureau of vines at the University of Alabama, bristles with significance and challenges the wisdom and courage of the people of this State. Here is united, in common aim, the Engineering School of our State University, recognized for its competency and usefulness, and the Federal Bureau of Mines. The Bureau is one of the most effective arms of our National Government. It outranks in accomplishment, measured by practical scientific contribution, any like governmental organization in all the other nations. It possesses none of the characteristics of many other bureaus of government which have created popular bias. Here is one Bureau devoid of political suggestion or aim with a personnel zealously devoted to labor in scientific re¬search - an organization marked by practical accomplishment, alleviating many of life's burdens, raking easier life's pathway, and unerringly pointing to life's possibilities.

Jan 1, 1936

By Herbert H. Einstein

The thrust of research reported in Part I was to collect in-situ data from exploration programs and the published literature, and to empirically establish distributional patterns for these variables. Since discontinui¬ties in a rock mass govern to a large extent its engineering properties and thus the performance of any slope in the mass, work has been devoted to determining the appropriate distributional forms for attitude spacing and length of discontinuities and to distributional properties of resis¬tance and deformability parameters. The conclusion from these analyses is that trace lengths are logNormally distributed and that joint spacing is Exponentially distributed, regardless of orientation of the sampling line, and regardless of whether each joint set is considered separately or not. Joint orientation (attitude) data representing 22 individual joint sets from eight sites (a total or approximately 20,000 joints), do nor strongly support any of the commonly used distributions as broadly applicable in practice. The autocorrelation )f geometric joint properties is also examined. However, no significant spatial correlation could be found even after extensive data manipulation. The investigation of resistance and deformability parameters starts with a review of mechanisms and models that are used to represent them. Review and statistical evaluation of approxi¬mately 2,000 discontinuity shear tests has shown that good statistical estimates for use in reliability analyses can be obtained for friction angles.

Jan 1, 1979

By H. Herbert Hughes

Soapstone commonly is associated with talc , and reports on either commodity usually contain a discussion of the other . From a geological or mineralogical standpoint the combination is justifiable , for soapstone essentially is impure talc . Commercially , however , the relation between them is remote . About 95 per cent of all talc sold in the United States is in ground form, whereas practically all soapstone is sold as furnace blocks or as fabricated structural slabs for many and diverse applications .

Feb 1, 1932

By Frank E. Cash

The compensation-insurance rates for quarrying in North Carolina are 11 times higher than for the State?s major industry, textiles. Some operators are willing to accept this as representing the ratio of existing hazards. This was not true of the management of the Southern Aggregates Corporation, and in 1935 it tools definite steps to correct the idea of its local officials and employees that loss of life and limb in quarries is inevitable. ACKNOWLEDGMENTS The authors acknowledge gratefully the assistance and information concerning these operations furnished by H. M. Shaw, safety director (also secretary and treasurer), Southern Aggregates Corporation, Raleigh, N. C.; by the following superintendents: J. H. Rodgers, Blair Quarry, Blair, S. C.; J. D. Lane, Greystone and Rolesville Quarries, Henderson, N. C. ; J. H. Arthur, Guilquarry, Stokesdale, N. C.; J. H. Watkins, Rockton Quarry, Wendell, N. C.; P. A. Wellenborne, Reidsville Quarry, Reidsville, N. C.; and J. L. Kirchin, Woodleaf Quarry, Woodleaf, N. C.; by the various foremen at the plants, and by Murry Id. Grier, safety engineer, North Carolina Department of Labor, Asheville, N. C.

Jan 1, 1940

By Ivette E. Torres

Aruba, formerly a. part of the Netherlands Antilles, separated on January I, 1986, and became an autonomous part of the Netherlands. Full independence of the island from the Netherlands is scheduled for 1996. In this chapter, however, Aruba's statistics are included with those of the Netherlands Antilles. Tourism continued to be the main industry of the island, which continued to depend heavily on imports, mostly from the United States. During the year, the Government was preparing legislation to regulate the exploration of oil deposits in the relatively shallow sea around Aruba.

Jan 1, 1989

By M. H. Kline

The Great Gossan Lead in Carroll County, Va., is one of the largest undeveloped sulfide ore bodies known in the eastern United States. It extends for 16.7 miles along the western slope of the Blue Ridge Mountains (fig. 1). The various known segments of the deposit, extending from the southwest end to the northeast, are: The Great Outburst or Iron Ridge segment, Chestnut Creek, Copperas Hill, Sarah Ellen, Wild Cat, Cranberry, Dalton Hill and offset segment to the south of the Cranberry, Little Reed Island, Little Vine, and the Betty Baker at the northeast end. All of these segments have been explored or mined to various extents in the past for the iron gossan and secondary copper ore. The Great Outburst or Iron Ridge segment is now being mined by the General Chemical Division of the Allied Chemical & Dye Corp. for the sulfur and iron content of the primary ore. These deposits are becoming increasingly of Interest as a. large potential source of iron and sulfur owing to their proximity to Birmingham, where the burned cinder sells at a premium, and to the acid markets of the region.

Jan 1, 1949

By Arno C. Fieldner

The objectives of the coal-research activities of the Bureau of Mines are very well expressed in the organic act of Congress establishing the Bureau. It reads as follows: That it shall be the province and duty of the Bureau of Mines, subject to the approval of the Secretary of the Interior, to conduct inquiries and scientific and technologic investigations concerning mining, and the preparation, treatment and utilization of mineral substances with a view to improving health conditions, and increasing safety, efficiency, economic development, and conserving resources, through the prevention of waste in the mining, quarrying, metallurgical and other mineral industries; to investigate explosives and peat; and on behalf of the Government to investigate the mineral fuels and unfinished mineral products belonging to, or for the use of, the United States, with a view to their more efficient mining, preparation, treatment, and use; and to disseminate information concerning these subjects in such a manner as will best carry out the purposes of this act.

Jan 1, 1946

By David A. Lipton

U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources and potential of the Moses and Dennison Peak RARE II areas in Tulare County, California. These areas, along the west slope of the Sierra Nevada, are underlain by grarnitic rocks of the Sierra Nevada batholith and contain numerous metasedimentary roof pendants. Silver, copper, and zinc occur in contact-metasomatic deposits within the metasedimentary rocks. In the Moses area, the Powell Mine (fig. 1) contains an estimated 90,000 tons (82,000 t) of subeconomic silver, zinc, and copper resources. The King Solomon Prospect has 3,000 tons (2,700 t) of silicified phyllite containing zinc. On the Helen-Joyce Prospect, 44,000 tons (40,000 t) of gossan occur above a poorly exposed silver-zinc rich zone. Potential exists for additional mineral resources and occurrences at each of these properties.

Jan 1, 1983

By Lawrence K. Requa

The property being worked by the Lewiston dredge of Placer Development (Ltd.) is on the Trinity River in Trinity County, Calif., about 9 miles north of the town of Lewiston (see fig. 1). The nearest rail point is at Rending, Calif., which is exactly 50 miles bar road from the dredge camp. Recently a very good section of State highway has been constructed from Redding to Weaverville, and it is now possible to use this highway for 35 miles of the distance between the dredging property and Redding. The remaining 15 miles, however, are over ordinary dirt road. No trouble is experienced in reaching the property except for a few weeks during the middle of the winter when snowstorms may make travel difficult but not impossible. At present the property consists of about 500 acres of patented land, which extends for about 3 miles along the main Trinity River and Stuart's Pork. It is being worked with one 7-cubic foot, Bucyrus-type dredge, which has an average monthly capacity of about 100,000 cubic yards. To the end of 1931 approximately 10,000,000 cubic yards of gravel had been dredged.

Jan 1, 1932

By Robert J. Hundhausen

During the early part of World War II , it appeared likely that supplies of chromite for United States industry might become critically short . As a part of the ensuing search for new sources of domestic chromite supply , the chromite - bearing black sands along the coast of southern Oregon were hurriedly investigated by State and federal agencies and by private interests , These investigations led to a decision to begin exploitation of the deposits immediately . A government stock- piling program was put into effect , a concentrator was financed by the Defense Plant Corporation , two privately controlled companies were encouraged to start mining operations , and the Bureau of Mines and the Geological Survey were authorized to search. for additional reserves of minable ore .

Feb 1, 1947

By M. G. Zabetakis

Benzene and toluene are the first two members of an important homologous series whose general formula is CnH2n-6. The members of this series differ in composition from benzene by some integral multiple of CH2; they can all be prepared in the laboratory by the Wurtz-Fittig, Friedel-Crafts and Grignard syntheses. Because 'of the industrial importance of these-hydrocarbons, the limits of flammability of eight members of the series have been determined at 100° C.-(A temperature of 1000 C. was chosen because the determination of the upper limit of flammability of p-cymene requires an apparatus temperature. of at least 90° C. As elevated temperature data are available for other combustibles at 100° C. but not at 90° C., all data were taken at 100° C. in order to obtain comparable results.) Minimum ignition temperatures of these combustibles have been determined at laboratory-pressures.

Jan 1, 1951

By Verne E. Hooker

The Bureau of Mines conducted a preliminary investigation to determine the state of stress in crystalline rock outcrops near Atlanta, Ga. The secondary principal stresses in a horizontal plane near the surface are compressive and are 500 to 3,000 psi. The maximum compressive stress is northeast-southwest in the Stone Mountain-Lithonia district but changes to northwest-southeast near Douglasville. The elastic constants were determined from data obtained by static and dynamic laboratory methods and in situ velocity measurements. Results show Young's modulus to be dependent upon both stress level and anisotropy in the rock. Average secant moduli obtained from triaxial tests were used to compute the applied stress from borehole deformation measurements.

Jan 1, 1966

By William H. King

The Mercur Dome mine is in the Camp Floyd mining district, Tooele County, Utah (fig. 1). The property lies between 6,000 and 8,000 feet altitude on the southwesterly slope of the Oquirrh Mountains, a short distance west of Mercur, the district settlement. Mining began in the Mercur area in 1870. Operations at the Mercur Dame mine were started in 1937 after several claims had been consolidated into one group. Preliminary examination of the ground by F. H. Gunnell, a Bureau of Mines engineer, disclosed the presence of vanadium in a carbonaceous shale horizon. Rocks near the Mercur Lame property are chiefly sediments of Carboniferous age, including the Madison and Deseret limestones. The main shaft penetrates the Deseret formation to a point a few feet above the 1,000-foot level where it enters the Madison limestone. The flat-lying vanadiferous shale horizon is exposed on the 1,000-foot level near the top of the Madison limestone. The Bureau of Mines development program, consisting of diamond drilling, auger hole drilling, and sampling, was planned to determine the extent and assay value of the vanadiferous bed. Seven diamond-drill holes totaling 300 feet were drilled from the 1,000-foot level of the mine. Eight hand auger holes were drilled in the back of the drift on this level (fig. 2). Assay determinations were made on 74 samples from the drill holes and supplemental channel samples and are tabulated in this report. The concluding section embodies results of metallurgical tests.

Jan 1, 1949

By F. E. Diebold

The wastewater-treatment system of the Anaconda Mining Co., at its Butte, MT., operation has been physically and chemically characterize modeled on a computer and investigated with respect to alternate systems for economic heavy metal recovery. The system involves lime addition to a mixture of acid underground copper sulfide mine water, acid effluent water from the iron induced precipitation of copper from acid leach solution and basic suspensions of solid effluent from a concentrator plant. Experimental chemical analysis and predictive computer calculations shows that the monosulfllte and disulfllte complexes of transition metals (Iron II being dominant) and alkaline earths are 40% of the total dissolved metal load of both acid streams. The suspended solids (30% by weight) in the basic concentrator slurries are dominated by quartz and pyrite and also contain kaolinite muscovite, biotite and undissolved lime. The mixture of these three streams result's in major reductions in concentrations of Al, Cu, Fe, Mg, Mn, Sir and Zn, and a pH >7 with calcium, sodium, potassium, and sulfate being the major dissolved ions. The treatment system has been simulated in the laboratory and accurately modeled on a computer. The computer program, an altered REDEQL-EPAK, is capable of accurately predicting the amount of lime required to reach a desired effluent water. Preliminary research has indicated the usefulness of electroprecipitation as a means of recovering the valuable metal load and providing an EPA acceptable effluent.

Jan 1, 1982

By Bernard S. Covino

The Bureau of Mines is conducting a study of methods to improve the efficiency of the process used to pickle stainless steels. A review of the literature on pickling of stainless steels showed that the chemistry of several process operations involved in the pickling of stainless steels is not fully understood, and that further research could improve the pickling efficiency. The benefits of this research would be a reduction in the annual loss of several thousands of tons of critical minerals such as nickel and chromium, and a reduction in the amount of solids and spent acid solution that are currently discarded. The conclusion from this review is that further research is needed in four operations that either directly or indirectly influence the pickling process: hot working, annealing, conditioning, and the actual operation of pickling, Laboratory studies of the pickling operation are presently in progress.

Jan 1, 1984

By Victor Himel

This report documents a systematic approach towards implementing an improved ensemble for the mine rescue team system that will protect against the hazards of mine rescue and recovery and will also afford improved performance through increased comfort and maneuverability, lighter burdens, and improved human engineering designs. In the first part (Task 1) the mine rescue team's protective needs were defined along with the test methods required to evaluate whether a particular piece of gear met these needs. Task 2 assessed existing gear against performance criteria and standards developed in Task 1. Task 3 consisted of the conceptual design and construction phases of the MRPE program. Special consideration was given to advanced concepts, materials, and equipment.

Jan 1, 1982