Search Documents

By A. B. Hooker, P. G. Guest, E. J. Gleim

"From time to time the United States Bureau of Mines has received reports of gas explosions alleged to have been caused by correctly assembled flame safety lamps. In most of the mines where the explosions occurred the lamp was in use at a working face where the velocity of the ventilating current would be relatively low. The inference has been that the lamp was correctly assembled but that the gauze became sufficiently overheated to ignite the surrounding atmosphere.As part of its routine investigation of flame safety lamps the Bureau of Mines subjects each lamp to a test in still and moving atmospheres to determine its safety. Heretofore, as long as the lam, successfully passed this and other tests no determinations as to the margin between success and failure were made; hence, in attempting to answer inquiries concerning the reported explosions it was found desirable to be able to give actual gauze temperatures as a measure of the comparative safety of lamps under various conditions. The previous laboratory tests of flame lamps in still mixtures were made in a chamber or ""gallery"" of relatively small volume where the lamps might have been subject more or less to the smothering effect of the combustion products. It was therefore decided to make a special series of tests to obtain the gauze temperatures of both bonneted and unbonneted lamps in still and low velocity mixtures, using a larger gallery to offset any smothering effect.These tests are believed to represent the first attempt at measuring gauze temperatures by means of themocouples. The results will not only be of interest but will also be helpful to many in determining the status of flame safety lamps relative to gas ignitions in mines."

Feb 1, 1929

By Elizabeth A. Johnson

The vaporization thermodynamics of the aluminum-silicon carbides Al4SiC4 and Al8SiC7 were studied by the Bureau of Mines over the temperature range of approximately 1,500 to 1,700 K. Vapor pressures were measured by a Knudsen effusion-mass spectrometry technique in which powdered samples were effused from graphite crucibles through small orifices. For each compound, a total of six orifice diameters was tested to verify equilibrium within the cell. Aluminum, mass number 27, was the only vapor species detected over the range 4 to 200 amu. Experimental results are based on the following equations for incongruent decomposition: A14SiC4(cr) - 4A1(g) + SiC(a,hex) + 3C(gr); Al8SiC7(cr) - 8A1(g) + SiC(a,hex) + 6C(gr). The observed vapor pressure-temperature relationships determined with a cell orifice area of 2.0 x 10-3 cm2 for Al4SiC4 and 1.81 x 10-3 cm2 for A18SiC7 are the following: Log P - (-18,682/T) + 12.476, for Al4SiC4 (1,550 to 1,643 K) and Log P = (-19,308/T) + 12.421, for Al8SiC7 (1,526 to 1,784 K), with P in pascals and T in kelvins. Third-law analysis of the data provided the following heats of formation: A14SiC4 ?H at 298.15 K - -50.0 kcal/mol and A18SiC7 ?H at 298.15 K - -92.1 kcal/mol.

Jan 1, 2011

By Henry E. Perlee

Air compressor explosions that are caused by the ignition of combustible vapor mixtures cannot be explained by a single reaction mechanism or sequence of events. Explosions have been caused by the sudden release of large quantities of lubricating oil, by the rapid vaporization of oil that had accumulated slowly in high-pressure piping, and by the production of decomposition products from carbonaceous deposits. Ignitions can be caused by the heat produced in a catalytic reaction, in a compression process, or when a shock wave is propagated through a combustible vapor-air mixture. The frequency of these ignitions can be minimized by establishing proper maintenance and cleaning schedules. Further study is needed to satisfactorily correlate the various factors involved in compressor explosions.

Jan 1, 1963

By R. D. Rosenkranz

The Bureau of Mines has investigated the availability of copper from 272 deposits in market economy countries. The deposits studied have demonstrated resources totaling 413 million metric tons of contained copper and account for more than 90 pct of the reserve base for market economy countries. Using data gathered as part of its Minerals Availability Program, the Bureau performed geologic, engineering, and economic evaluations in order to determine the copper production potential of each deposit. At the 1981 copper market price of $0.85/lb, the deposits studied could economically produce an estimated 88 million metric tons of copper (allowing for profit computed at a 15-pct rate of return), primarily from mines operating at the time of the study (1981). At this price, producing mines in market economy countries could economically produce only 2.1 million metric tons of refined copper per year. However, actual 1981 production was 6.2 million metric tons, indicating that many mines continued to operate even though they were unable to cover all production costs. For U.S. producing mines, the estimated average cost of production per pound (including profit at a 15-pct rate of return) was $0.15 higher than the average cost in other market economy countries.

Jan 1, 1983

By R. H. Nafziger

Bureau of Mines research has shown that very low-sulfur pressure vessel steels with improved mechanical properties can be prepared by two melting processes. Four pressure vessel steels having sulfur contents ranging from 0.0008 to 0.0040 wt-pct, were produced by the electric-arc furnace or by the electroslag processes. Calcium carbide was used as a desulfurizer in the electricarc furnace. Fluxes containing at least 40 wt-pct CaO provided sufficient desulfurization during electroslag remelting. Element recoveries were higher for electroslag remelting than for metal melted in the electric-arc furnace. Bar rolled from electroslag-remelted ingots generally possessed higher tensile strengths and ductility than bar rolled from it t melted in the electric-arc furnace. Charpy V-Notch upper shelf energies were also improved as a result of electroslag remelting. The primary failure mode during impact testing was was microvoid coalescence. Sulfide inclusions were minimal, especially in the electroslag-remelted material.

Jan 1, 1979

By J. B. F. Champlin

The continuing development of the nuclear industry in the United States requires a program of waste disposal that insures against the release of large amounts of radioactivity to the environment. This paper describes research on one proposed means of disposal of this waste, that of injection into geologic formations at depth. Nuclear production plant wastes were simulated and injected into samples of sedimentary rock obtained from outcrops, quarries, and deep wells. Changes in the chemical and physical characteristics of the rocks caused by the interaction of ions and suspended particles in the waste solutions with the cementing material and claylike particles in the rock are discussed. Laboratory tests show that nuclear wastes can be injected into many natural porous, permeable geologic formations. Injectivity can be maintained over a longer period by monitoring the ionic balance and particle-size distribution of waste streams. The combination of permeability and porosity with low cation-retention capacity, as exhibited by most sandstones, would satisfy the engineering requirements for the subsurface disposal of nuclear waste. Shales and clays with their low permeability and high cation-retention capacity would make excellent confining formations. The amount of cation retained by sedimentary rocks increases with increasing valence or concentration of the cation or decreasing brine concentration. The use of rock cores as model reservoirs had proved successful in determining some of the parameters that need to be considered in full-scale field disposal of wastes.

Jan 1, 1967

By D. S. Kingery

Efficient transportation is necessary to complement modern mechanized mining methods. The increasing trend toward high-capacity face loading equipment has demanded equally efficient haulage methods; this has been met by increasing mine-car sizes, using larger locomotives, and increasing haulage speeds, all requiring properly installed and maintained haulage roads specifically designed for this type of traffic. The recommendations and specifications included in this circular were made to point out salient factors important to the proper construction and maintenance of track haulage roads and to serve as recommended standards for track installation and maintenance. GLOSSARY OF TERMS USED Haulageway. - The track, walkway, trolley wire, feeder lines signal end telephone lines, signals, telephones, support, and drainage of the entry referred to. Subgrede. - The base upon which the ballast is laid.

Jan 1, 1954

By Lester J. Crow

A preliminary survey was performed to investigate the impregnation of relatively weak, porous volcanic tuff and a relatively strong, dense sandstone with five different monomers. Increases in compressive strengths by factors of 2 to 5, and elastic moduli by factors of 2 to 3.5, are reported for natural rocks (tuff., sandstone, dacite), which were impregnated with five monomers (methyl methacrylate; chlorostyrene; 40 percent TMPTMA-60 percent styrene; 40 percent TMPTMA-60 percent chlorostyrene; 60 percent polyester-40 percent styrene); polymerization took place after monomers were forced into the rock. Impregnation was performed (1) by pressurizing rock specimens from one end, or (2) by a vacuum-soak operation. Polymerization was accomplished by either radiation or chemical initiation techniques. Strength improvement is dependent on (1) the type of monomer used, (2) the amount of polymer incorporated into the rock, and (3) the degree of water saturation of the rock. Water saturation strongly reduced the effectiveness of the method for the polymer systems tested. The more viscous monomers (for example, 60 percent polyester-40 percent styrene) were more effective in displacing the water from the rock, and compressive strengths of wet rock were doubled with these systems. Water saturations ranging from 25 to 100 percent of maximum saturation gave essentially identical results. Further tests on other types of mine rock; including shale and coal, are planned. Water-compatible polymer systems should be developed, or present systems should be suitably modified. For application to tunnel stabilization, design studies evaluating the improvement in rock strength and its influence on the support system are also recommended.

Jan 1, 1971

The contractor examined L.T. White's Patent No. 3524680 and, finding it in need of engineering refinements, proceeded with a conceptual design of a variable wall mining machine. The contractor then proceeded to assess the feasibility of the variable wall mining machine measured against the criteria specified by the U.S. Bureau of Mines. The feasibility was judged from a physical aspect, a health and safety aspect, and an economic aspect. The Variable Wall Mining Machine was judged to be feasible on all three aspects provided that certain specified practices were adopted. Description The specifications and design and performance parameters of the Variable Wall Mining System as conceptualized are summarized in Tables I and II. The system consists of a side-cutting auger operating in a string of identical 12 ft. sections, along a 500 ft. retreating longwall face. In addition to the 41 identical sections, there is a special drive and discharge section at the head gate.

Jan 1, 2012

By George D. Drechsler

The purpose of this review is to provide an analysis of the supply and demand for coal in Europe in 1955-56 and estimates of future growth in European requirements as a medium for appraisal of the effects and benefits to the economy of the United States. This review stems from observations and evaluations made in contacts with Government and industry representatives of the principal countries of Europe and is based on detailed data selected from the established flow of unclassified economic and statistical material originating in overseas areas for use and deposit in the Bureau of Mines, Foreign Solid Fuels Section. This material includes current reports and analyses prepared by the United States Foreign Service, official reports of individual countries, foreign industry and trade publications, and the committees of the several European organizations engaged in continuing review and study of problems relating to fuels and energy. The review is presented in four sections: 1. Discussion of the more important factors relating to the present and future fuels and energy position of Western Europe.

Jan 1, 1957

By E. F. Ferrell

Electrowon molybdenum powders and a commercial hydrogen-reduced powder, all with different minor impurities, were investigated by the Bureau of Mines with respect to inherent properties, to fabrication techniques, and to proper-ties of the fabricated sheet. Compared with the commercial hydrogen-reduced powder, the electrowon powders had a larger particle size, a greater flow rate, a higher apparent density, and a lower oxygen content. Sheet materials prepared from the two types of powders showed similar mechanical properties, under the same conditions of heat treatments, except for low-temperature ductility. Yield strengths varied with carbon content, heat treatment, and test temperature.

Jan 1, 1970

By Henry P. Cole

A series of studies are described that identify critical health and safety skills needed by underground coal miners for coping with mine emergencies. First aid and self-rescue and escape were selected as two broad performance domains that include many subordinate skills needed for preventing, recognizing, and coping with mine emergencies. The performance domains and their objectives were used to direct the development of simulation exercises that permit miners to experience mine emergencies in the safety of a training room. The exercises are based upon research with similar simulations for the training of flight crews and medical personnel in information gathering, judgment, and decision making skills. Exercise content is drawn from actual mine accident and disaster case studies. The exercises incorporate recent principles of cognitive psychology and instructional design. Initial studies in annual refresher training classes suggest the exercises are stimulating for miners and their instructors, easy to use and read, sufficiently complex and authentic to challenge experienced miners, and useful devices for both teaching and testing critical problem solving skills required for preventing and minimizing emergencies.

Jan 1, 1988

By A. Gene Collins

Rapid, sensitive, and precise methods of determing major, minor and trace constituents of oilfield brines are needed. Several methods have been developed or adapted by the Federal Bureau of Mines at the Petroleum Research Center, Bartlesville, Okla. The following methods are described in this report: Spectrophotometric and volumetric for iodides and bromides; potentiometric for pH, alkalinity, acidity, borate boron, total boron, and organic boron; gravimetric for potassium; disodium ethylenediaminetetraacetate (EDTA) volumetric for total hardness, calcium, and magnesium; spectrophotometric for fluorides; and color comparison .for arsenic. Adequate sensitivity, precision, and accuracy were obtained for each method. The Bureau of Mines pioneered in research on the analysis of oilfield waters (2, 46, 47).6 However, several of these early procedures were quite time consuming. Also, they did not include methods for determining trace and minor constituents of brines.

Jan 1, 1961

By R. E. Heithecker

The separation of enormous quantities of water produced with the oil in some West Texas fields necessitated the use of special equipment other than the regular lease tanks. Several methods were used with varying degrees of success. They include the water-trap, hay tank and gun barrel, gun barrel and settling tank, chemical and electrical-dehydration methods. The water trap which has been used extensively in the Hendricks field, and in some instances has been installed in the Yates field separates the water and. oil under high pressure before tile liquid and gas pass through the flow beam. The first trap was constructed and installed by the Southern Crude Oil Purchasing Co. in July, 1928. By July, 1929, approximately 300 traps were in use. Treating cut oil by running it through a hay tank was done quite extensively in the Roberts-Settles field, Howard and Glasscock Counties, Tex., and later the method was used in the Hendricks field. In July, 1931, there were 37 hay tanks in the Roberts-Settles field, treating the oil from 123 wells. The cut oil frequently was made acceptable to the pipe-line company by running it through the hay tank. In some instances, however, it was necessary to heat the oil, and occasionally both heat and chemicals were used before complete separation of the oil and water was obtained.

Jan 1, 1932

By R. E. Heithecker

[The separation of enormous quantities of water produced with the oil in some West Texas fields necessitated. the use of special equipment other than the regular lease tanks. Several methods Were used with varying degrees of success. They include, the water-trap, hay tank and gun barrel, gun barrel and settling tank, chemical, and electrical-dehydration methods. The water trap which has been used extensively in the Hendricks field, and in some instances has been installed in the Yates field separates the water' and. oil under high pressure before tile liquid and gas pass through the flow ?bean. The first trap was constructed and installed by the Southern Crude Oil Purchasing Co. in July, 1928. By July, 1929, approximately 300 traps were in use.]

Jan 1, 1932

By R. S. Dean

The function of the Metallurgical Division is to conduct investigations relating to the treatment of mineral products from the state in which they are mined to the refined metal or other unfabricated product. These investigations include scientific and practical studies of ore dressing, covering the crushing and grinding of ores, separation by gravity, flotation. and magnetic methods; the hydrometallurgical treatment of ores, including cyanidation and amalgamation of the precious metals; the smelting and refining of copper, lead, and zinc, as well as the rare metals; and steel-melting practices from the raw ore to the finished steel. The object of this work is to conserve natural resources and eliminate waste by furnishing information on current methods of metallurgical practice. making fundamental studies of metallurgical processes, and developing new processes to the point of demonstrating their practicability. The Division is made up of sections devoted to the several phases of this work, each section being headed by an investigator capable of supervising his particular work. The work is carried on at the experiment stations and field offices or in the field, whichever seems best suited for the work in hand. The following, projects should be mentioned as particularly outstanding among those consummated successfully during the year: 1. Application of the type of chemicals known in the textile industry as wetting-out agents to flotation and agglomeration of ores, particulary soluble salts such as sodium and potassium chloride which must be treated in saturated brine. 2. Demonstration or a linear relation between surface and coercive force in magnetic minerals and Its application to magnetic separation and to the determination of grinding efficiencies and other metallurgical data which require surface determination at very fine sizes. 3. Pilot-plant demonstration of the practicability of the reduction of iron ore by natural gas and conversion of this direct iron into steel by direct melting and by forging and rolling before melting. The structure and properties of the iron so produced were studied in detail. This report covers the fiscal year July 1. 1934, to June 30, 1935.

Jan 1, 1936

By W. K. Sawyer

Resistivity, porosity, permeability, and saturation data were obtained on core samples from the Big Injun, Clinton, Gordon, Bradford Second and Third, and Venango Second oil sands and formation factor-porosity relationships were derived using the general form of Archie's equation F = aø-m, where F is the formation factor, ø is the porosity, and a and m are constants that depend on characteristics of the rock. It was found that a and m varied significantly between sands, as did the exponent in the Archie relation I = Sw-n, where I is the resistivity index and S, is the water saturation. The average exponent, n, determined from all data was 50 percent greater at residual oil saturation than at residual water saturation. Samples from each sand exhibited differences in directional resistivity and/or permeability. The Bradford Third sand data showed correlation between resistivity and permeability anisotropy.

Jan 1, 1971

By Emery Chilton, Charles Taylor, Mark Senk, Linda McWilliams

Three-axis ultrasonic anemometers are used to study airflow in the NIOSH ventilation gallery where ventilation in an underground mine is simulated. In this study, performance characteristics of this anemometer are evaluated and the effects of sensor orientation and sampler location on flow readings are examined. The study results provide guidelines for more effective use of the ultrasonic anemometers in the ventilation gallery.

By D. Harrington, R. R. Sayers

For several years the writers have been studying various phases of the effect of air conditions in metal mines upon underground workers ; in 1918 a short study was made in certain hot and deep mines and brief reports were issued in the Engineering and Mining Journal ( August , 1920) and in the U. S. Public Health Reports (Vol . 36 , No. 4 , January 28 , 1921 ) . In 1921 a more extended study was made (also in hot and deep metel mines ) with intent to determine the limiting conditions imposed upon underground workers by the physiological effect of various air movements , temperatures , and humidities , with and without work . It is the purpose to publish a series of short papers on this later investigation , each paper to consider one particular phase of the work . The present paper deals with the effect on body temperature and pulse rate in still air as compared with moving air of temperatures from 90 to 100° F . and 100 per cent relative humidity, the subjects at rest .

Apr 1, 1923

By R. E. Brewer

Published investigations show that many different chemical reagents have been used in determining the constitution of coals , but only a few studies have been applied directly in evaluating the effects of such reagents on the carbonization products of coal , Most of the treatments have been so drastic that any permissible conclusions that may be drawn are inferential in respect to any favorable effects on the yields and composition of the usual carbonization products .

Sep 1, 1943