Search Documents

By E. A. Loria

High-quality sheet of electrowon molybdenum was attained by a sequence of procedure on pressed and arc-melted crystalline powders. The procedures included high-temperature, high-vacuum sintering treatments and the use of metal deoxidizers instead of carbon to improve the mechanical properties of the molybdenum sheet. Rolled sheet 60 mils thick was evaluated by tensile and bend tests, hardness measurements, microstructures, and recrystallization treatments. After stress relieving, yield strength ranged from 85,000 to 110,500 psi (0.2- percent offset) and ultimate strength ranged from 87,200 to 117,250 psi with 4.5- to 25-percent elongation observed for arc-melted sheet, and 5.0- to 23- percent elongation observed for powder metallurgy sheet. In room temperature bend tests the sheet yielded plastically, indicating that the ductile-brittle transition point was below room temperature. The diamond pyramid hardness (DPH) of the molybdenum sheet changed from 214 to 293 DPH for the stress-relieved condition to 177 to 185 DPH for the fully recrystallized condition. The brittleness of recrystallized molybdenum, reported by other investigators as characteristic of sheet prepared from commercial-grade hydrogen-reduced powders, was not in evidence. Recrystallized tensile specimens pulled at room temperature had an average elongation of 31 percent.

Jan 1, 1966

By F. E. Block

This investigation was made as part of a larger program to develop basically new methods for preparing yttrium metal in high-purity form. It was performed under a cooperative agreement between the U.S. Atomic Energy Commission (AEC) and the Federal Bureau of Mines. Laboratory-scale tests were made to devise methods for preparing high-purity, anhydrous yttrium trichloride, for reducing the yttrium trichloride with sodium or lithium, and for consolidating the resulting yttrium sponge into ingots.

Jan 1, 1960

By W. W. Adams, T. D. Lawrence

"Despite the manpower shortage and other difficulties of operation in war time, the National Safety Competition of 1943 for the promotion of safety in the mineral industries of the United States was notable for having a larger enrollment of mines and quarries than in any other year except 1941 and 1942 since the yearly safety contests were inaugurated in 1925. The competition was also notable for having a larger number of man-hours represented by the competing companies than in any previous contest except that of 1942. The ratio of accidents and days of disability resulting from accidents to the number of man-hours of work performed was more favorable than in 1942; the accident-frequency rate was lower and therefore better than in 13 of the 19 years during which the annual safety competitions have been conducted, and the accident-severity rate was better than in 16 of the 19 years.The National Safety Competition is a yearly safety contest conducted by the Bureau of Mines, United States Department of the Interior. Companies that win first place in their respective group in the contest are awarded a bronze trophy, ""The Sentinels of Safety,"" which is provided by THE EXPLOSIVES ENGINEER magazine. Competing companies are segregated into six groups: Underground bituminous-coal mines, underground anthracite mines (in Pennsylvania), underground metal mines, underground nonmetallic-mineral mines, open-cut mines (without regard to kind of mineral produced), and open quarries (without regard to kind of stone produced). The bronze trophies are retained by the six winning companies for 1 year and are then transferred to the winners of the succeeding year's contest. On the pedestal of each trophy is engraved the names of the winners of the trophy. With the award of the trophies for 1943, therefore, the pedestal of each trophy bears the names of 19 winners."

Aug 1, 1944

By D. E. Redmon

Linear programing provides a mathematical technique by which activities can be planned in such a way that an optimal result is obtained. Routine applications of linear programing require only a knowledge of algebra. However, a complete understanding of the fundamentals of linear programing requires a knowledge of advanced mathematics. The purpose of this publication is clarification of terminology and illustration of applications in comparatively simple mining problems. Two mining situations are considered: Mine stopes from which ore is to be produced at a minimum production cost; also, uranium mines from which ore is transported to one mill, a maximum monetary value is desired. The details of data arrangement for solution by linear programing are described and the solutions are presented. Results of these solutions indicate successful applications of linear programing to mine production scheduling.

Jan 1, 1964

By C. J. Walker

The Bureau of Mines undertook a theoretical and laboratory study to determine the feasibility of using ethylene as a tracer for natural gas in underground gas-storage reservoirs. The study indicated that ethylene was a useful gas tracer in underground gas storages. Tracer losses were not excessive. Laboratory tests were conducted at pressures as high as 500 psia in both wet and dry consolidated-sandstone cores, evaluating tracer loss with gas blends containing natural gas with different concentrations of ethylene tracer. Under certain conditions losses were less than 17 percent.

Jan 1, 1966

By R. A. Busch, R. R. Backer, R. W. McKibbin

The Bureau of Mines conducted laboratory tests to determine the slur- ry transport and deposition properties of coal waste. A 188.5-ft pipe test loop was constructed with instruments to measure density, flow, and power and discharge, suction, and differential pressures. A 20-ton sample of Western coal waste was crushed and screened to 100 pct minus 1/2 in. Eight loop tests using this graded waste were run at slurry densities ranging from 1.15 (25 wt-pct solids) to 1.46 (60 wt-pct sol- ids). The resultant friction-pressure gradients ranged from 0.06 to 0.24 ft of water per foot of 4-in standard steel pipe. Particle-size degradation was significant. In a typical loop test lasting 25 min, the minus 200-mesh fraction increased from 19 pct to 34 pct. Deposi- tion tests showed that without the use of a flocculant, the slurries would not dewater when left to stand for 1 week. With flocculant, ad- ditional water was released; however, the settled slurries remained thixotropic. Further testing is necessary to determine their suitabil- ity for use as backfill material in active mines.

Jan 1, 1965

By W. H. Oppelt

Converting small-particle lignite to a stable, storable fuel of relatively high heating value was investigated. The fuel was prepared by thermal pretreatment of the lignite in an 8-inch i. d. rotary-drum retort, then the pretreated material was pelletized in an experimental 15-inch-i. d. rotary-drum pelletizer. Pelletizing tests were made with both starch and bituminous binders. During the first phase of the project, the quantity, composition, and heating value of products from the thermal processing of Kincaid lignite from Burke County, N. Dak., in an B-inch i. d. rotary-drum retort were investigated at a series of temperatures from 250° to 950° F. to establish optimum conditions for preparing feed material for pelletizing. To determine the response to thermal treatment of different lignites, 5 other lignites from Divide, McLean, Mercer, and Stark Counties, N. Dak., and 1 lignite from Saskatchewan, Canada, were processed at 700° F.

Jan 1, 1958

By Donald O. Capstick

[ ]

Jan 1, 1983

By J. E. Tress

The Bureau of Mines prepared submicron tungsten powder by reducing tungsten hexachloride with hydrogen. The particle diameters of the resulting tungsten powders ranged from 0.015 to 0.046 micron. Within the limits of the variables investigated, no clear-cut correlation was found between process conditions and final size of the powder. Oxygen was the major contaminant in the product; being present both as an adsorbed gas and as suboxides of tungsten. Studies showed that the powder yielded compacts of approximately 45 per-cent of theoretical density when compacted mechanically. Low-temperature sintering produced more rapid densification in these compacts than in compacts prepared from conventional powders. Adding up to 20 percent ultrafine powder to conventional tungsten powder caused an increase in density upon compaction with maximum densification occurring at approximately 12 percent ultrafine powder.

Jan 1, 1966

By Otis E. Perkins

This paper is one of a series being prepared for the United States Bureau of Mines to disseminate technical information retarding the methods used in mining nonmetallic minerals. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. This paper deals particularly with methods and costs of dredging, classifying materials, and transportation at the plant of the Ross Island Sand & Gravel Co. of Portland, Ore. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of Harold Blake, general manager of the company, and of A. V. Kramer, cashier in charge of the plant office.

Jan 1, 1933

By George E. Fish

This report describes investigations conducted by the Bureau of Mines from 1957 through 1959 in the Roseland anorthosite-titanium belt of Nelson and Amherst Counties, Va., for the purpose of studying the titanium resources of the area. Three titanium deposits containing much saprolite ore derived from the decomposition of anorthosite and diorite were selected for detailed study Following a reconnaissance of the reported titanium occurrences in the belt. These three deposits occur in or are associated with anorthosite. Most of the occurrences are situated on or near the contact between the anorthosite and the gneissic country rock. The saprolite deposits are as much as 1.5 miles long, 1,000 feet wide, and 100 teat deep and contain significant reserves of titanium-bearing material estimated in excess of 20 million tons. Where it was penetrated by drilling, the unweathered rock beneath the saprolite contains nearly the same titanium values as the saprolite.

Jan 1, 1962

By L. C. IlsLey

Most State enacting bodies have deemed it necessary to specify a maximum speed at which men may be hoisted or lowered in mine shafts. Since most mine cages are not closed in, as are passenger elevators in office buildings, and since, ordinarily, neither the starting tin g nor stopping of the cage is as general as that of these elevators, such regulations are all the more necessary for the comfort and safety of the men. It is also quite generally recognized that it is dangerous to over-crowd cages. Hence, a number of States have limited the number of men that may be on cage at one time.

Jan 1, 1939

By W. P. Diamond

Coalbeds exhibit a directional permeability, with the maximum permeability oriented parallel to the face cleat. Thus, the most efficient pattern of vertical degasification holes for a coalbed is dependent upon cleat orientation. Surface joints, infrared photolinears, and Ronchi grating photolinears were investigated as potential estimators of subsurface cleat orientation. Cleat orientations were measured in 18 mines, in the Pittsburgh coalbed in southwestern Pennsylvania and northern West Virginia to be used as a standard against which prediction techniques would be evaluated. Two cleat systems with a strong geographic segregation were measured in the study area: N 670 W -N 280 E (950 separation) for the north, and N 76° W -N 17° E (930 separation) for the south. Directional data obtained from the three techniques investigated yielded satisfactory regional predictions of cleat orientation. Analysis of surface joints was the only technique considered sufficiently reliable on a local basis. Prediction of cleat orientation is based on the pairing of the principal directional sets into all reasonable combinations of fundamental systems. The system or systems composed of the most dominant sets nearest to 90° separation are likely to be a reliable prediction of cleat orientation. The most dominant set of the system selected is likely to be the face cleat.

Jan 1, 1976

By Jerry T. McLendon

The proper disposition of phosphatic clays has been the subject of research and debated for years by phosphate producers, State and Federal research agencies, regulatory authorities, and environmentalists. To date, no "universal" solution exists for the ultimate disposl of phosphatic clays. This Bureau of Mines report examines the state of conventional clay disposal technology and reviews the technical progress of innovative alternatives. Twenty impoundment sites were investigated by the Bureau of Mines using geotechnical methods and laboratory analysis of cored samples. In addition, quasi-static cone penetrometer soundings were conducted to define clay and/or sand-clay interfaces en masse. Samples of the top, middle, and bottom hole segments were obtained at each station for laboratory studies of clay densities, pore fluids, plasticity, and mineralogical properties. The results of this study support the continued use of initial clay settling impoundments but emphasize the need for "in-line" systems to reduce the initial volumes of plant-generated phosphatic clays. The effective use of sand tailings is also encouraged to promote further consolidation of clays via self-weight stressing, sand-clay admixtures, and/or surcharging sand caps.

Jan 1, 1984

By John T. Neubert

Between 1988 and 1990, the U.S. Bureau of Mines studied the mineral resources of San Juan National Forest to appraise and determine types and locations of deposits that could be mined economically now and in the foreseeable future. The study included a comprehensive field examination and literature search. Substantial amounts of lead, zinc, copper, gold, and silver have been mined from within the Forest in the La Plata, Rico, Silverton, and Dunton areas. At least one buried 200 million ton stockwork molybdenum deposit occurs in the Rico area. Similar size porphyry copper deposits occur at the surface and about 1,700 feet below the surface in the Bedrock Creek area of the La Plata district. Numerous smaller base-and precious-metal and uranium deposits have been prospected and mined throughout the Forest. Coal, oil, and gas have been or are currently being produced in the western and southern parts of the Forest. Carbon dioxide occurs in the western part of the Forest. Strategic elements occurring within the Forest include platinum, palladium, cadmium, gallium, indium, bismuth, and tellurium; however none of these elements is economically recoverable at present. Several geothermal areas are scattered across the eastern two-thirds of the Forest. Industrial minerals within the Forest include sand and gravel, limestone, and decorative stone.

Jan 1, 1992

By R. A. Busch

Sludge ponds of fine coal, fine soil, and water created behind large piles of coarse coal waste can present hazardous conditions; this is a Bureau of Mines report of the subsurface physical property data developed on the fine coal waste materials that make up the core areas of two typical coal waste impoundments. These data will help define more completely the engineering properties of this problem area of the structures. Additional calorific, chemical, and mineralogical data were obtained on the coal waste materials to determine possible uses or development of byproducts. The possibility of extracting alumina from coal ash was also investigated.

Jan 1, 1975

By W. C. McBee

A family of modified-sulfur cements has been developed by the Bureau of Mines for the preparation of construction materials with improved properties. Various types of sulfur cements were prepared by reacting sulfur with mixtures of dicyclopentadiene (DCPD) and oligomers of cyclopentadiene (CPD). Durable cements were prepared with structural characteristics ranging from rigid to flexible. These cements were used to prepare corrosion-resistant materials for use in a wide variety of industrial applications where resistance to acidic and salt conditions is needed. These materials were prepared as rigid concretes, flexible pavings, spray coatings, and grouts. Production of modified-sulfur cements in a commercial-size plant was demonstrated.

Jan 1, 1981

By L. B. Pankratz, R. Barany, W. W. Weller

Experimental determinations were made of the heats of formation at 298.15 ° K of cuprous ferrite and cupric ferrite ; the heat capacity of cuprous ferrite was measured over the temperature range from 50 ° to 298 ° K and the entropy at 298.15 ° K was evaluated ; the heat contents of cuprous ferrite and cupric ferrite above 298.15 ° K were measured to 1,500 ° K and 1,100 ° K , respectively . These thermodynamic values were combined with other pertinent data to obtain heat and free energy of formation values at high temperatures . The stability of the two ferrites with respect to their constituent oxides is discussed . Thermodynamic values are included for the decomposition of cupric ferrite to form cuprous ferrite , magnetite , and oxygen .

Jan 1, 1964

By Gary E. Sherman

To aid the U.S. Army Corps of Engineers in their Resource Development Navigation Study of ten existing or proposed port sites in Alaska, the Bureau of Mines examined the potential for mineral development around three Alaska port sites: Iliamna Bay, Kotzebue, and Nome. The mineral deposits near Iliamna Bay include gold, copper, and iron. Development of minerals in this area will require the discovery of new deposits or the definition of additional are reserves at known deposits. The mineral deposits near Kotzebue are primarily gold, copper, coal, lead, and uranium. Based on the character of these deposits, it appears that development of a small-scale mine supplying coal for regional use is the most likely scenario in the near-term. The mineral deposits near Nome are primarily gold and copper. Development of small underground gold mines is possible, however it appears that expanded offshore gold dredging will have the greatest impact on the flow of freight and goods through the Nome port in the near term.

Jan 1, 2011

By Pamela J. Watson

The U.S. Bureau of Mines has demonstrated in laboratory tests that drilling with surface-charge-neutralizing concentrations of polyethylene oxide (PEO) polymer solutions simultaneously improves penetration rates and extends bit life. The applicability of this additive to improve drilling performance in coal measure rocks was demonstrated under field conditions at an abandoned mine land site in Pennsylvania and a producing coal mine property in Ohio. Penetration rate improvements ranging from 15 to 50 pet were obtained when core drilling through a variety of coal measure lithologies. Drilling cost analysis indicates that the small added cost of using the polymer is more than offset by the savings that result from demonstrated increased drilling penetration rates, which translate into drilling cost savings of about 10 to 30 pct. This report also gives chemical analyses of a variety of coal measure rocks and some corresponding local drilling water samples, obtained from a wide geographical base, along with threshold concentrations of PEO required to effect the improved drilling performance in these rocks. From these data, the threshold PEO concentrations needed to ensure improved drilling performance can be estimated for any coal measure rock suite. Proper techniques for mixing PEO solutions are also presented.

Jan 1, 2010