Search Documents

By V. A. Nieberlein

This paper presents the results of research undertaken to recover titanium and columbium by low-temperature chlorination of low-grade columbium-bearing ilmenite concentrates, and to simultaneously remove chlorinated impurities from the volatile chlorides without resort to distillation. Coke-reduced ilmenite was chlorinated at 400° to 500° C., and the resulting TiC14 was free of most impurities before condensation. A heated purification column was used wherein various packing materials reacted chemically or physically with the impurities which passed through them in the vapor phase. A nearly water-white TiC14 product was obtained directly. The principal impurities in the titanium tetrachloride were: 0.02 percent Fe, 0.01 percent V, 0.05 percent A1, 0.04 percent Si, and 0.07 percent Cb. This is a less pure product than commercial TiC14. Most of the columbium was recovered as crude CbC15, requiring further refining.

Jan 1, 1960

By V. A. Marple, K. L. Rubow, Y. Tao

"A personal diesel exhaust aerosol sampler has been designed and evaluated in both laboratory and field settings. The sampler uses size selective sampling for the determination of the respirable mass concentrations of mineral dust and diesel exhaust particulate matter found in underground coal mines. This design is based on the premise that diesel exhaust particulate matter is predominantly less than 0.8 um while mineral dust is greater than 0.8 gm. Operating at a flow rate of 2 L/min, the sampler consists of a 10 mm Dorr-Oliver respirable dust cyclone followed by an 0.8 gm cutpoint impactor and an afterfilter. Field evaluations consisted of sampling at 6 different locations in these underground coal mines. Measured aerosol concentration less than and greater than 0.8 um have been compared with a well characterized cascade impactor.Techniques must be developed for measuring the mass concentration of diesel exhaust particulate matter found in underground coal mines due to the health concerns associated with worker exposure to diesel exhaust particulate matter. Diesel exhaust particles are in the respirable size range and have been regarded as a potential occupational carcinogen by NIOSH (1988). Furthermore, a 1988 MSHA advisory committee directed MSHA to develop a sampling protocol for assessing worker exposure to diesel exhaust particles.The University of Minnesota and the Bureau of Mines, over the past 4 years have measured the size distribution of diesel exhaust particles and mineral dust, both in the laboratory and underground mines (Cantrell, 1987; Cantrell et al., 1987; Cantrell and Rubow. 1988; Marple et al, 1986; Rubow et al., 1988: and Watts et al., 1989). To date, measurements have been made in nine coal mines. Seven mines utilized diesel-powered equipment at the mine face while two used electric-powered equipment. The results of these field tests indicate that mineral dust and diesel exhaust particles can be differentiated on the basis of particle size. The measured particle size distributions have been found to be bimodal with a saddle point at 0.8 um. This has led to the hypothesis that one method for measuring worker exposure to diesel exhaust particles would be to collect size fractionated particle samples separated at 0.8 um with the diesel particles being less than 0.8 um and the mineral dust particles greater than 0.8 um.Aerosol size distribution measurements, using a micro-orifice uniform deposit impactor (MOUDI), have been conducted in the mine intake air portal, intake entry to the working section, haulageway, and section return entry. The MOUDI is a ten stage cascade impactor with particle cutpoints ranging from 0.1 to 15 um aerodynamic diameter (Marple and Rubow. 1984b; Marple et al., 1989). The sampling flow rate is 30 L/min."

Mar 1, 1992

By John Ward Smith

This paper describes and evaluates a method that the Federal Bureau of Mines used to determine the ultimate composition of the organic material in 10 samples of oil shale from the Mahogany zone of the Green River formation in Colorado and Utah. Since interest has centered on the Mahogany zone, the richest section of the deposit, these 10 samples were chosen to provide a broad representation of this zone with the objective of obtaining generally valid ultimate composition values. The most probable organic composition for the Mahogany zone and the 95-percent confidence limits for each component average (in weight-percent of organic material) are: Carbon 80.5 ± .4 Hydrogen 10.3 ± .1 Nitrogen 2.4 ± .1 Sulfur 1.0 ± .1 Oxygen 5.8 ± .5 As only minor variations in composition were observed, the organic material of this particular bed is quite similar over a wide geographic area.

Jan 1, 1961

By V. A. Marple, K. L. Rubow, S. M. Behm

"An eight-stage cascade impactor, with cut-sizes ranging from 0.056 to 18 um at a flow rate of 30 L/min, has been developed, calibrated, and tested in field programs. This impactor, called a microorifice uniform deposit impactor, has several features not normally found in cascade impactors. Ultrafine particles as small as 0.056 um are collected while keeping the pressure drop moderate by utilizing multiple nozzles (up to 2000) as small as 52 um in diameter. At each stage the collected particles are deposited uniformly over the entire impaction plate by rotating the impaction plate relative to the nozzles and by the correct radial placement of the nozzles. The particle cutoff characteristics (collection efficiency curves) of each stage and inter-stage losses were determined by means of monodisperse aerosols. The cutoff characteristics were found to be sharp and similar for all stages.Inertial impactors are widely used for the size-selective collection of aerosol particles. One reason for their wide usage is that the principle of operation is simple: a jet of particle-laden air is directed at a flat impaction plate. Large particles are collected on the plate while smaller particles follow the airflow out of the impaction region and are not collected. The division between the size of particles collected and those that are not is quite sharp. Secondly, the particles in an impactor are classified by their aerodynamic diameter (an important size parameter in many fields of study, including those related to respirable particle health effects). Thirdly, it is easy to collect particles in discrete size ranges by passing the aerosol through a number of stages (one stage consisting of a nozzle and impaction plae) in series, with each subsequent stage collecting particles smaller than the one before it. This is known as a cascade impactor. Finally, impactors can classify particles over a wide range of particle sizes: as low as 0.005 um (Fernandez de la Mora et al., 1990) and as large as approximately 50 um (Vanderpool et al., 1987).This paper describes a general purpose cascade impactor that has been developed in our laboratory and used in a variety of studies including visibility studies (McMurry et al., 1986; McMurry and Zhang, 1989), underground mine studies (Marple et al., 1986; Rubow and Marple, 1988; Rubow et al., 1988), and general atmospheric pollution studies (Macias et al., 1981; Dzubay et al., 1984). The impactor, called a microorifice uniform deposit impactor (MOUDI model 100, MSP Corp., Minneapolis, Minn.), is the integration of two earlier impactor de¬velopments: the microorifice impactor (M01) (Kuhlmey et al., 1981) and the uniform deposit impactor (UDI) (Marple et al., 1981).The MOUDI has several features normally not found in other cascade impactors. These include collection of particles as small as 0.056 um in aerodynamic diameter with a moderate pressure drop, uniform particle collection on the impaction plates, inter-changeable impaction plates to allow for the plates to be easily and quickly changed in the field, and covers for these substrates to provide a means for safe storage and/or transport of the collected particles to the laboratory for analysis."

Mar 1, 1992

By John J. Mulligan

The Bureau of Mines investigated reports of mineral deposits within 10 miles of the route of the proposed pipeline from Prudhoe Bay to Valdez. No producing lode deposits or lode prospects of possible national economic significance were found. Measured placer deposits in the route are or slight value except possibly some deeply buried gold placer deposits in the Fairbanks and Livengood Quadrangles. The pipeline corridor crosses five belts of minerals having potential economic value: (1) The north slope of the Brooks Range (oil, gas, oil shale, coal, phosphate); (2) the south slope 01 the Brooks Range (copper, gold); (3) the Livengood area (gold); (4) the Fairbanks area lead-silver, antimony); and (5) the Wrangell Mountains-Denali copper belt (copper-gold). The Jarvis Creek coalfield, an eastern extension of the Nenana coalfield, is on the north side of this belt. Scattered along the corridor across the Chugach Mountain and in the vicinity of Valdez are a wide variety of metallic deposits that make up the eastern margin of the Chugach gold belt but do not seem to constitute a well-defined zone.

Jan 1, 1974

By Richard L. Sayrs

The Eve Mills deposit is in Monroe County, Tenn., near the southeastern corner of the State. The deposit was examined in February 1943 by a Bureau of Mines engineer, and drilling the property was recommended to increase the on: reserves enough to justify mining should war needs require it. The deposits were explored, by 32 diamond-drill holes totaling 11,649 feet during the periods from July 1943 to November 7, 1945, and from April 1944 to August 17, 1944. The drilling campaign disclosed a large area of mineralization. The ore, however, is apparently confined to long, narrow sheets. The indicated grade of the ore bodies blocked cut by the Bureau of Mines is 4.o8 percent zinc and 2.10 percent iron.

Jan 1, 1949

By J. Baicker

A two-inch diameter probe containing an intrinsic germanium detector, a canister-type solid cryogen cooling system, cooled FET preamplifier, linear amplifier, high voltage supply, analog-digital converter, microprocessor, buffer memory, bidirectional cable link, and all power supplies has been designed, assembled and tested. A surface support vehicle was designed, built and outfitted. A mini-computer system was constructed and preliminary software developed and tested. A special handling system for a Cf-252 neutron source was designed and has been ordered. The entire system (less the neutron source) is ready for its first field tests. Lab description of the system is presented.

Jan 1, 1978

By D. Montagna

This Bureau of Mines report describes a salt-free, fluxless method for reclaiming metallic aluminum from aluminum dross. The dross is smelted under argon, nitrogen, or carbon dioxide, instead of a salt flux, in an externally heated pot furnace. Aluminum recovery, using argon, is equal to recoveries reported from commercial smelters that process dross in rotary-type furnaces This salt-free method could offer a reduction in air pollution, lower energy requirements by elimination of salts, and the production of up to 60 percent less solid waste for disposal than the salt method.

Jan 1, 1978

By R. R. Lowery

An analysis of three 1-1/4-diam manufactured wire ropes of 6x19 classification was done to identify and describe reference conditions of new rope. Reference condition is of value when examining tested or retired ropes. Measurements of strand and rope pitch and of wire and rope diameter confirmed adherence of all ropes to those construction specifications. Mechanical properties of strength and ductility were determined by accepted methods for the ropes and wires from the ropes. Individual wires from one rope failed to meet minimum wire ductility values. Wire chemical composition varied in average carbon levels, from 0.70 to 0.78 wt pct, and in manganese content, from 0.45 to 0.80 wt pct. One manufacturer's product contained 1 to 3 wt pct Ni and Cr. Heavily wrought pearlitic steel microstructures were porous and contained inclusions. Cold work variations were evidenced by wrought grain width. Recorded anomalies reflected the condition of the manu-factured products. The report provides data that compare the three wire ropes studied, but cannot verify the effects that these conditions or anomalies have on rope service life.

Jan 1, 1983

By M. E. Tyrrell

The Bureau of Mines produced building brick of good quality in an investigation designed to explore the possible utilization of high-glass fractions of municipal incinerator residues in the manufacture of building products. Common clays, lime, and sodium silicate were used as binders for the nonplastic residues Test bricks were formed by dry-pressing, soft-mud molding, and stiff-mud extrusion. A run of standard-size face brick dry-pressed and fired in the West Virginia University Coal Research Bureau pilot plant demonstrated that SW-grade glass-clay face brick can be produced on a commercial scale without difficulty. A cost evaluation made for production of the brick showed an estimated cost of $42.13 per thousand bricks for a shuttle kiln plant and $28.70 per thousand for a tunnel kiln plant.

Jan 1, 1972

By D. W. Frommer, M. M. Fine

Laboratory investigations have produced flotation concentrates contain- ing 91 to more than 92 percent titania, with fair recoveries, from the Christy property, Hot Spring County, Ark. The titanium-bearing ore on the Christy property occurs in a quartz-clay- iron oxide mineralization, which contains, on the average, about 6.0 percent TiO2, chiefly as the mineral brockite; brookite and rutile are different crys- talline forms of titanium dioxide. Recent work by the Bureau of Mines has shown that titanium chloride can be produced readily from the rutile-type mineral by reduction with coke fol- lowed by low-temperature chlorination. Metallic titanium is in turn derived etallic from the chloride by the Kroll process .

Mar 1, 1952

By Nicholas Kyriazi

A joint effort by the U.S. Bureau of Mines (USBM) and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CPR 75.1714), held up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSR's in the fourth phase of testing from 1989 to 1993. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except units with manufacturing defects. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. In addition, some apparatus collected for this study had not been returned to the manufacturer in a recall effort for correction of a manufacturing defect. In both cases, the apparatus would have presented problems in emergency use. Recommendations include improved training in inspection procedures and better enforcement of recall notices.

Jan 1, 2010

By Hillary W. Clair

An equation is derived for the rate of reaction of a sphere of metal oxide in a restricted enclosure through which a reducing gas is flowing . The equation takes into consideration the reaction rate coefficient , transport through the gas and through the porous shell of reduced oxide , the rate of gas flow , and the volume of the enclosure . The equation serves as a model for predicting the course of reduction of a particle of metal oxide in a shaft furnace .

Jan 1, 1964

By William P. Diamond

In this U.S. Bureau of Mines study, production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 to 10.1 x 106 m3. Peak production rates were generally about 0.03 x 106 to 0.06 x 106 m3/d, but rates over 0.10 x 106 m3/d were observed. The variability of gas production from individual holes can be attributed to' several factors, including completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance is hole location. Holes on the ends of the panels, where overburden strata are in tension because of the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location, which is in compression. Analysis of 7 months of gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 2010

In order to reduce waste and improve resource conservation, mine planning, and development, the U.S. Bureau of Mines is investigating the effects of multiple seam interactions associated with longwall coal mining. Field investigations were conducted at a mine located in Boone County, WV, where a longwall panel was operating subjacent to room-and-pillar workings in an overlying seam. To assess the effects of overlying workings on longwall headgate stability, the Bureau gathered various geotechnical information at this minesite. Headgate pillars and entries were instrumented and monitored to study their behavior during side-abutment loading as the longwall panel approached and passed beneath the overlying room-and-pillar developments. The two operations are separated by 800 ft of interburden, and although interactions between operations separated by this distance are uncommon, geomechanical measurements indicate the occurrence of an interaction. These measurements show that convergence on the headgate entries was most adverse subjacent to barrier pillars in the overlying mine. Pillar measurements indicate that side-abutment pressure increases were slightly greater than predicted values. Several factors related to both geology and mine design, believed responsible for this large interactive distance, are discussed.

Jan 1, 1990

By J. L. Holman

The Bureau of Mines is conducting research to recover strategic and critical metals such as Ni, Co, and Cr from mixed contaminated super-alloy scrap. One approach being studied involves melt refining of superalloy scrap to produce anodes for electrolytic deposition of Ni-Co alloy. This melt refining of superalloy turnings is described based on melt-oxidation and oxidation-carburization experiments, using roasted superalloy grinding sludge to supply the 0 needed to oxidize Cr and other readily oxidized elements to the slag. Controlled melt-carburization subsequent to oxidation improved the metal phase recovery of Ni and Co to well over 90 pct and decreased electrolytic solubility of Cr, Mo, and W by carbide formation. Electrolytic refining experiments were conducted using a controlled-potential mode (preset cathode potential). Data show effects of Fe and Cr impurities, cation concentration, electrolyte pH, S04-Cl electrolyte ratio, temperature, cathode potential, and cation-selective membrane use on current efficiency, current density, and deposit composition. Disposition of Ni, Co, Cr, MO, W, and Fe is compared for melt-oxidized versus oxidized-plus-carburized anodes. Deposits containing >97 pct Ni + Co (major impurity Fe) have been routinely obtained from scrap anodes. Research is continuing to improve deposit quality in sustained deposition and to recover Cr and other metals from refining slags and anode sludges.

Jan 1, 1986

By K. L. Williams

The Bureau of Mines laboratory tested the response of a commercially available real-time aerosol monitor (GCA RAM-1) to various dusts. Monitor measurements were recorded, averaged, and compared with simultaneous gravimtric measurements of each test dust. Tests usually lasted several hours. The test dusts of various particle size distributions used included coal, limestone, and a commercially available test dust. For each particular dust, the monitor response was linear and correlated well with mass concentration over the range of about 0.5 to 10 mg/m3. The monitor can estimate a 2.0-/m3 respirable coal dust concentration within as little as 26 pct with 95 pct confidence. The monitor must, however, be calibrated with the dust to be measured because the instrument response is affected by the type of dust particle. The average monitor response to same mass concentration of coal dust was approximately twice the average monitor response to the same mass concentration of limestone dust.

Jan 1, 1984

By E. D. Gardner

"In recent years efficient safety organizations have been considered essential at all well-managed metal mines. Statistics from numerous mines throughout the country show that the expense of operation of these safety departments is repaid many times by the saving due to fewer accidents. Men trained in first aid, mine rescue and fire-fighting are important parts of the safety organization at most mines. It is more desirable, however, to lay stress ma accident prevention and fire precautions rather than on first aid and fire fighting. Both of these phases of safety work have been well developed in the Globe Miami district. The co-operative mine rescue organization* in this district under Orr Woodburn, is one of the best in the country. Mine rescue teams are kept trained at all the mines and the oxygen breathing apparatus is constantly maintained in good condition. Miners are also trained in first aid, and are offered incentives to make themselves proficient both in mine rescue and first-aid work.The Old Dominion Company is among the leaders in the safety movement in the Globe-Miami district. The safety department at this mine was established January 1, 1914, and has been developed to a high degree of efficiency. W. G. McBride, general manager of the company, takes an active part in the safety work and has given Albert Talon the safety inspector, his active support in developing the organization. The success of the department is dos largely to the ability, tact, and personality of the men directing the work.The following description of the establishment and operation of the safety organization at this mine was prepared from information supplied by Mr. Tallon."

Jun 1, 1921

By Harold Bailie

The purpose of this Bureau of Mines report is to furnish information on mining practices applied to flat-bedded fluorspar deposits in southern Illinois. It presents new and improved operating procedures and specialized techniques applicable to deposits of this type. All of the operating mines of the Ozark-Mahoning Co. in this area have been opened by vertical shafts which connect with levels consisting of haul-age ways, stopes, and loading stations. The stoping practice used locally called room and pillar, is open stoping with pillars left at different distances and diameters. To facilitate haulage and drainage, the mines are worked from openings turned off the main haulage drift on a grade to conform with the dip of the ore beds. The ore is predominantly fluorspar with smaller amounts of galena and sphalerite that contain traces of cadmium and germanium. The principal gangue minerals are limestone, calcite, shale, barite, and sandstone. The rock hardness ranges from relatively soft shale to hard, abrasive sandstone.

Jan 1, 1960

By Edwin M. Murphy

Methods are described for filling underground cavities remotely with dry material pneumatically injected through a borehole to seal openings, prevent air movement, and reduce subsidence; this often brings underground fires under control by limiting the access of air. Large-scale tests were made in the Bureau of Mines Experimental Coal Mine, Bruceton, Pa., in an operating mine, and in an abandoned Pennsylvania mine. Supplemental trials were made aboveground in galleries and in the laboratory. The parameters studied include horizontal and inclined passageways, obstructions in the entry, water leakage into the borehole, dry material, and grout and slurry mixes. The materials studied were fly ash, crushed and pulverized limestone, and sand. Best results were obtained with dry fly ash, though satisfactory seals were obtained with the other materials. When a borehole is dry and ends at an open void, casing is not necessary. If more than 5 gpm of water flows in the borehole, if the void contains loose debris, or if coarse material is injected, a material feedpipe should be inserted through the borehole. Fly ash was most suitable for remote filling because of its low angle of repose (8°) and its good flow characteristics. The depth of borehole through which the fly ash is injected has no appreciable effect on the filling operation.

Jan 1, 1968