Search Documents

By Vern L. Kegler

This paper is one off a series dealing with mining methods and costs, sponsored and published by the United States bureau of Mines. ACKNOWLEDGMENTS The author acknowledges the, constructive and helpful suggestions and criticism of W. F. Lamoreaux, vice-president, and general manager of the Ducktown Chemical & Iron Co. United States Geological Survey Professional Paper- 139, by W. H. Emmons and F. B. Laney, has been drawn upon for some of the information contained in the paragraphs or history and geology.

Jan 1, 1931

By James A. Whelan

The Bureau of Mines sponsored research studies of variables in rotary drilling, done in the Department of Mineral Engineering, University of Minnesota. By studying carefully controlled drilling with good instrumentation, it was hoped to obtain a better understanding of rock failure during drilling and of the stresses in drill bits during drilling. Experimental procedures and equipment are described. From these studies it was concluded that 1. Thrust requirements, other things being equal, are proportional to the total length of cutting edge in the bit. 2. Data from penetrating a wedge into rock under thrust only are not directly applicable to rotary drilling. 3, In rotary drilling the initial wear on a bit greatly decreases penetration rate under any given set of conditions; however, after initial wear the effect of wear on penetration rate is reduced. 4. An increase in rotary speed increases the overall penetration rate but decreases the penetration per revolution. 5. An increase in thrust increases the overall penetration rate and the penetration per revolution. 6, Torque on a drill bit is proportional to both penetration rate and bit diameter. 7. For small-diameter holes full-hole drilling will save both drilling time and energy compared with pilot drilling followed by reaming; for large-diameter holes pilot drilling-reaming is advantageous in both respects,

Jan 1, 1962

By M. E. Tyrrell, C. W. Houck

Mixtures of zirconium diboride and refractory metals of group VI were resistance sintered to high - density compacts using modified electric welding equipment . To evaluate the use of chromium , molybdenum , or tungsten as binders for zirconium diboride the sintered compacts were examined in polished sections and tested for crushing strength , hardness , microhardness , oxidation rate , and resistance to mechanical shock . Chromium yielded the highest compressive strength , the greatest resistance to mechanical shock and oxidation , and a satisfactory Rockwell hardness . Molybdenum did not yield a satisfactory cermet . Tungsten yielded compacts having high microhardness but very low mechanical strength .

Jan 1, 1964

By D. E. Wolfson

This report describes the carbonizing properties of the principal coal beds of Allegheny County, Pa., which rank low in the high-volatile A bituminous classification. Seven coal samples from 3 coal beds were selected for study, as follows: 2 each from the Redstone and Pittsburgh beds and 3 from the Upper Freeport bed. Selection was based on estimated reserves. The samples of Upper Freeport and Pittsburgh coals were satisfactory chemically for producing metallurgical coke. The ash contents of the samples of Redstone coal were moderately high. One of the samples of Redstone coal was high in sulfur content, and it would be difficult to upgrade to meet present metallurgical standards.

Jan 1, 1959

By H. B. Brunot

The United States Bureau of Mines under provisions of Schedule 2C4 issues approvals covering complete operating units such as loading machines, room hoists, and storage-battery locomotives. Certain manufacturers design and build entire machines. Other manufacturers purchase a part or all of the electrical accessories from manufacturers of electrical equipment and make up permissible units by assembling them. Before the assembler purchases electrical accessories for use in such contemplated units he may require certain information from the accessory manufacturer as to whether the particular accessories are suitable for assembly in his proposed permissible outfit. To aid accessory manufacturers in marketing their product, a provision was incorporated in Schedule 20 whereby tests might be made on individual accessories and reports rendered as to the suitability of a given accessory for use in permissible assemblies.

Jan 1, 1935

By Travis Q. Lyday

Australia was one of the world's principal producers of minerals and metals, and its minerals industry was a leading catalyst in promoting growth of the country. Australia was the world's largest producer of alumina, bauxite, diamond, ilmenite, monazite, opal, rutile, sapphire, and zircon. It was the premier exporter of alumina, coal, ilmenite, refined lead, monazite, rutile, and zircon, and was the second leading exporter of iron ore, after Brazil. Ranking behind China, the United States, the U.S.S.R., the German Democratic Republic, Poland, and the Federal Re-public of Germany, Australia was the seventh largest producer of coal (all grades) in the world. Australia was the fourth largest gold producer in 1988, after the Republic of South Africa, the Soviet Union, and the United States. It was the second largest producer of zinc, the third largest producer of nickel, the fourth largest producer of uranium, and the seventh largest producer of copper. 2 The country's mineral wealth was so extraordinary that it was virtually self-sufficient in most mineral commodities. Endowed with abundant resources of coal, natural gas, liquefied petroleum gas, and uranium, Australia was one of the few market economy countries that was a net exporter of mineral fuels. About 90% of Australia's consumption of crude oil was supplied by domestic production; this was expected to decline significantly about 1990, unless significant new oilfields were discovered.

Jan 1, 1990

By Grace N. Broderick

U.S. supply and demand data for coal, by States and regions, were tabulated for the years 1960 and 1965. Estimates are provided of State-by-State quantitative data for the coal industry that can be integrated into State and regional energy balances by source, form, and consumer sectors, and used for estimates of interstate and interregional energy flows. The tables give an estimated total supply of coal available for consumption, and also report the distribution of the supply among the major consuming sectors (household and, commercial, industrial, transportation, and electricity generation). To enable comparison of coal data with those for other energy forms, tonnages were converted to British thermal units (Btu). Future energy analysis studies could be facilitated by changes in the categorization of information collected on the coal industry. The data shown are based primarily on Bureau of Mines source material.

Jan 1, 1969

By Ronald S. Conti

Historically, underground mine rescue teams have received training only in the course of actual emergencies, or in simulated mine environments, usually on the surface, with placards to identify objects and hazards. Also, while U.S. Federal Regulations require all underground miners to walk escapeways and conduct fire drills every 90 days, this does not fully prepare them for the conditions that may be encountered in real escape situations, such as smoke filled entries. This paper describes technology and realistic training simulations that have been identified for the general workforce and mine emergency responders. Of all the technology evaluated by underground personnel, laser lights and lifelines were most beneficial in leading personnel to safety and out of the mine in smoke-filled passageways. These technological advancements can improve the state of readiness for rescue personnel and increase the chances of survival for personnel escaping from underground emergencies.

By Edwin B. Cook

This report presents the results of calculations of the equilibrium composition of the products of combustion with air of six different mixtures of octane CgH18, plus PbEt4 and halogen-bearing scavengers at three air-fuel ratios, at pressures of 5 and 30 atm., and at temperatures of 350°, 1,000°, 1,800°, and 2,000° K. The air-fuel weight ratio has the values 12, 15:12, and 18. The concentration of PbEt4, M, in milliliters per gallon of iso-octane, has the value 1 or 3. The word "case" is used to designate the halogen concentration. Three cases have been considered [ ]

Jan 1, 1953

By Mark Sheppard

This paper is the third of a series recording the results of tests made at various quarries throughout the United States to determine (1) the relation between the size gradation of feed to, and product from, primary crushers, (2) the particle shape of the crushed. product, (3) the differences in gradation and particle shape produced by different types of primary crushers, and (4) the differences in gradation and particle shape caused by crushing different kinds of stone. Progress reports 1 and 2 dealt with comparisons of different types of crushers crushing the same type of stone. This report deals with relation¬ship between feed and product of two different limestones, as to size distribution and particle shape, when crashed in the same crusher.

Jan 1, 1938

By Andrew Cecala

Miner?s exposure to dust remains a top concern among regulatory agencies, particularly at production facilities with high levels of silica. This respirable dust is present in almost all operations and is a direct cause of the deadly disease silicosis. Silica is one of the most abundant minerals on Earth and is a threat at all operations, especial-ly granite and sand and gravel facilities. The National Institute for Occupational Safety and Health continues to analyze silica?s threat. The institute?s research indicates that heavy-equipment operators have an increased risk to dust exposure, especially when drilling or breaking rock, even when working from an enclosed cab. However, there are methods to reduce an operator?s exposure further, according to recent NIOSH research, which is detailed in its report, Improving Air Quality in Enclosed Caps with Uni-Directional Filtration/ Pressurization System. NIOSH indicates that when surface mining equipment is new, the operator?s dust exposure is normally at accept-able levels. As the equipment ages and components such as gaskets and seals deteriorate, the level of protection can degrade to a point where it is no longer acceptable. However, the institute indicates that at least two critical factors necessary for an effective system.

Jan 1, 2009

By S. Benedict Levin

The Big mine has been a source of mica and high-grade felspar from separate zones in the same pegmatite dike since 1914. In 1943 it became the outstanding producer of strategic mica in New England. The urgent need for sheet mica led to core-drilling by the Bureau of Mines from February to May 1914. Nine diamond-drill hob's aggregating 1,474 feet in length were drilled by the Bureau of Mines with the objective of developing extensions of the known mica shoots. The use of large-diameter bits made it feasible to obtain reasonably reliable results in diamond-drilling this type of deposit.

Jan 1, 1949

By D. Harrington

Approximately 6,000 coal mines are operated in the United States. All of them have in some degree the elements that are likely to contribute to an explosion, hence it is surprising that explosion disasters are not more frequent and that many mines have been operated for years and finally worked out and abandoned without experiencing an explosion. The absence of coal-mine explosions does not always indicate that effective efforts have been made to prevent them but rather that the nine has been fortunate in that the combination of circumstances necessary to cause an explosion has not existed. In view of present knowledge of the methods of preventing explosions, disasters are inexcusable and discredit the mining industry. The methods of preventing mine explosions are known to experienced, well-informed persons engaged in coal mining, yet despite this knowledge far to many coal-mine operators continue to use practices and methods that they should know have resulted in numerous explosions. Moreover, many mine workers persist in following past procedure irrespective of consequences and in breaking safety rules or indulging in practices almost certain eventually to result in disaster. Continued failure to apply known common-sense methods of accident and explosion prevention unquestionably will cell for ultimate enforcement of law.

Jan 1, 1940

By G. T. Fisher

The U.S. Bureau of Mines conducted research on calcium ferrite slags to determine the distribution of Pb and minor elements (Ag, Cd, Zn, and Co) between Pb bullion and slag. These fundamental data are required to evaluate nonferrous smelting with calcium ferrite slags as a substitute for conventional iron silicate slags. Determinations were made in 25-cm3-capacity MgO crucibles at 1,250° C for 2 h in a CO-CO2 atmosphere with an O2 potential that would retard the formation of magnetite. Calcium ferrite slag composition variables studied were from 16 to 32 wt pct CaO in 2-pct increments and Si02 ranging from 1 to 5 wt pct in 1-pct increments with equal additions of MgO. For all compositions studied, the retention of Pb in the calcium ferrite slag was less than 1 wt pct, which compares favorably to about 6 wt pct Pb in conventional iron silicate slags used in smelting of Pb concentrates. Minor element distribution was insensitive to changes in slag composition in the range studied. However, slag composition had significant impact on the melting and fluidity of the slag.

Jan 1, 2010

By Kenneth J. Miller

To determine the effectiveness of the many new flocculants available to the coal industry 20 of these reagents were evaluated treating slurry feeds to four refuse thickeners. Settling rates and supernatant liquid clarities were determined for each of the flocculants on the four slurries, and zeta potential measurements of the slurry solids were made. The test results showed that the flocculants provided comparable results when judged categorically as anionic, nonionic, or cattonic. It was also apparent that control of zeta potential insures maximum benefit from a flocculant.

Jan 1, 1968

By L. C. IlsLey, R. A. Kearns

"The electrical section of the Bureau of Mines has obtained copies of all available State safety rules and regulations in order to make a study of those portions of the codes relating to electrical equipment. While it has been found almost impossible to compare the several codes as a whole, comparison of those regulations dealing with a single subject has proved both interesting and instructive.Sixteen states have rules or enactments having reference to telephones and the present paper covers a compilation of these references. It is believed that data of this kind will be of service to commissions or other bodies contemplating the revision of existing codes.The compilation taken from the various codes follows: State Rules and Regulations.California.Sec. 5 (Par. c) Telephone communication shall be maintained between a co-operative station and each mine which it supplies. If the foreman in charge of a station does not reside thereat, his residence also shall be in telephone communication with each mine supplied by his station.Sec. 8 (Par. a) Whenever a fatal accident occurs in or about any mine, notice thereof shall be given promptly by telephone or telegraph if possible, followed by a notice in writing to the chief inspector, by the superintendent or other person having immediate charge of the work at the time of the accident."

Jun 1, 1921

By Jr. Gabler

World resources of cobalt appear ample for the foreseeable future; however, political and economic events have caused concern over the availability and reliability of an uninterrupted supply. Because of this concern, the U.S. Congress requested that the U.S. Bureau of Mines initiate a study of the flow of cobalt in the economy that would delineate and quantify the production areas where metal values are lost. As a result, the Bureau has developed a computerized commodity flow model. A major attribute of this model is that it is amenable to updating as supply, demand, and/or production data change. This report follows the flow of cobalt through its metallurgical and chemical applications and highlights areas where significant losses occur due to downgrading, export, or disposal. The study indicates that about 4,300,000 lb of cobalt-bearing materials are lost each year, representing 24 pct of U.S. domestic demand.

Jan 1, 1990

By H. Tomlinson

This circular is one of a series of papers on coal mining methods and costs which being prepared by the United States Bureau of Mines for the purpose of making available to those interested in the industry a knowledge of the mining methods employed, the places here mechanical and hand loading are practiced, and coat data on the several operations pertaining to the removal of coal from the working faces and its transportation to the tipple for loading into railroad cars. Mining costs are governed by the relative efficiency of the mining method employed. The method is selected for Its adaptability to the local natural physical conditions such as the nature and thickness of the coal bed, its dip, the character of the coal, and the thickness of the overlying strata.

Jan 1, 1930

By A. W. Khair, L. D. Gehl

"This paper describes the mechanism of coal and rock cutting from quasi-static indentation through dynamic indentation to rotary cutting. The results indicate that during quas~static indentation, a crushed zone, and subsurface fractures develop. The crushed zone is a potential source of dust generation. Dynamic indentation produces a crushed zone due to the frictional resistance offered by the coal or rock during penetration of the bit. Confining pressure changes the mode of failure from tension to mixed tension and shear. The wider bit causes larger crushed zone and more dust generation. The rotary cutting is a combination of quasi-static and dynamic indentation which results in chip formation. 1. INTRODUCTIONThe trend from conventional mining to continuous machine-cutting of coal, using more productive machinery is inexorable. Intolerable levels of dust generated at the face is an indication of inefficient coal or rock cutting by these machines. The Federal Government of the United States paid about 11.7 billion dollars workman compensation to more than 470,000 miners with Coal Workers Pneumoconiosis (Newmeyer, 1981). Bieniawski and Zipf (1985) reported that annual benefit payments were about 2 billion dollars. The need for research m improving coal cutting 1s therefore paramount. The enactment of Health and Safety Act in 1969 in the United States triggered the initial investigation into coal cutting mechanism and cutting tool design. The European countries were also engaged in the same area of research, however, their emphasis was in the use of wedge shaped bits. In 1981, the United States Bureau of Mines commissioned the South West Research Institute to investigate the effect of operating parameters mainly on airborne respirable dust in order to provide a healthier and safer atmosphere for coal mine workers.A research program by the Department of Mining Engineering, West Virginia University, USA was initiated to study the fragmentation mechanism during coal/ rock cutting. The research program was divided into three areas of research, namely quasi-static indentation, dynamic indentation and rotary cutting."

Dec 1, 1995

By Lester G. Morrell

While developments in Australia dominated the minerals industry of the South Pacific area, New Caledonia's nickel, manganese ore from New Hebrides, gold from Fiji and New Guinea, and phosphate rock from several small islands were significant in world supplies of those materials. The total value of mineral commodities produced in this area in 1965 has been estimated at about $763 million an increase of nearly 16 percent over the value reported in 1964. Increases were recorded in mineral production value with respect to that of 1964 for all of the countries except Papua-New Guinea where lower gold output resulted in a drop of about $300,000 and in the several phosphate-producing islands that collectively recorded a value decline of around $1.3 million. Exploration and development activities continued at an intensified level, not only in Australia and New Zealand but also in the British Solomons, Bougainville, and Fiji. Substantial additions to world supplies of iron ore and bauxite are assured and recent discoveries of natural gas, manganese ore, and nickel combine to give Australia a brilliant mineral outlook. Important discoveries of copper on Bougainville Island and on Vanua Levu, the north island of the Fiji group, and a gold mine on Misma Island were being developed during the year, with plans for early production underway. In New Zealand progress has been made on the New Zealand Steel Company project, and preliminary appraisal of a new titano-magnetite beach sand resource on the South Island has aroused considerable industrial interest. Extensive geophysical investigations were carried out in the British Solomon Islands and on Fiji's goldfields. The expansion program that will double output of products by New Caledonia's Société Le Nickel continued through 1965, and several foreign private companies have expressed a desire to initiate additional industries based on nickel prospects in New Caledonia.

Jan 1, 1967