Search Documents

By W. W. Adams

The metal and nonmetallic mineral mines (excluding coal mines) of the United States had a more favorable safety record in 1935 than in any year except 1931 and 1932 since annual statistics of accidents first became available in 1911. The accident rate was even lower than that for 1911, when the recorded rate probably did not reflect all of the accidents that actually occurred because many companies had not yet begun to keep complete records of accidents, especially those causing only minor injuries, and when, therefore, the number of accidents revealed by the companies' reports to the Bureau of Mines was probably not as complete as that reported for later years. Compared. with 1911, the accident rate covering fatal and nonfatal injuries in. 1935 decreased 13 percent. Compared with 1925, when the rate was the highest ever reported, the rate for 1935 decreased 47 percent and compared with 1934, 7 percent. The progress in safety which the mines of the country made in 1935 was not confined to any section or mining region; it was shared by a majority of the mining States and applied to underground mining operations, to open-pit mining, and to work at surface shops and yards. The rate for underground mining declined 8 percent from 1934; the rate for open-pit mining declined 14 percent, and that for surface shops and yards 12 percent.

Jan 1, 1938

By John K. Alley, Robert C. Johnson

The primary objective of the research was to grow aluminum borate whiskers or fibers and to determine their properties . Molten salt bath and vapor deposition methods were used for synthesis . Whiskers exceeding 25 mm in length were grown . The best results were obtained by vapor deposition and most of the data presented were determined on whiskers produced by this method of synthesis . Three different aluminum borate compositions ( 4.8A1203 B₂03 , 3.8A1203 B203 , and 2.5A120, B203 ) were identified by X- ray and chemical analyses . The aluminum borates 4.8A1203 B20, X- ray diffraction pattern was indexed . Optical data were obtained on the three aluminum borates . In addition the following whisker properties and growth factors were determined : ideal atmospheric dewpoint for vapor deposition method , near 65 ° F ; temperature range of whisker formation , 1,000 ° to 1,400 ° C for the molten bath method of synthesis , > 1,000 ° to < 1,400 ° C for the vapor deposition method ; whisker growth rates by the vapor deposition method , maximum 12 mm per hour ; raw material vaporization , 50 to 60 percent of the fluoride lost in 1 hour ; tensile strength , maximum obtained 174,162 psi ; melting points , ranged from 1,675 ° to 1,795 ° C.

Jan 1, 1965

Treat contaminated coal mine drainage to meet EPA and State water quality requirements. Approach A model (fig. 1) is presented for selecting, designing, and sizing one or several passive mine drainage treatment systems that can be used in remediation of abandoned mine lands (AML). The three principal types of passive mine drainage technologies for the treatment of coal mine drainage are an aerobic system, a compost wetland, and an anoxic limestone drain. The multistep approach presented here provides a simplified method to characterize the type and magnitude of the water quality problem and then to select either a single treatment system or a combination of treatment systems to address the specific site situation. How It Works Step 1. Discharge Characterization. Characterization of the discharge consists of measuring the discharge flow rate and collecting water samples at the point of discharge for chemical analysis. Both the flow rate and chemistry of a discharge can vary seasonally and in response to storm events. It is important to account for this variability by determining flow rates and water chemistry under various conditions.

Jan 1, 1992

By John M. Gomes

Two molten salt systems were evaluated as electrolytes for the repetitive recovery of tungsten from tungsten oxide (W03) made by calcining commercial-grade ammonium paratungstate. Using a sodium chloride-sodium fluoride-potassium aluminum tetrafluoride electrolyte at 800° C, 1 pound of 99.8 percent tungsten was recovered for each 2.7 kilowatt-hours of energy consumed. The metal contained 1,100 ppm carbon, was in dendritic masses of spherical grains, and had an apparent bulk density of 5.41 g/cm3. T ngsten of 99.9 percent purity was won from a sodium pyrophosphate-sodium tetraborate-sodium chloride electrolyte at 1,000° C; 6.0 kilowatt-hours of energy was consumed for each pound of metal recovered. The metal contained 120 ppm carbon, was in dendritic masses of hexagonal acicular crystals, and had an apparent bulk density of 7.25 g/cm . Each metallic impurity--aluminum, calcium, copper, iron, nickel, and silicon--in the two tungsten products was 16 ppm or less.

Jan 1, 1966

By Liane L. M. Kadnuck

This report summarizes the results of a hydrologic research study conducted by the U.S. Bureau of Mines (USBM) in cooperation with Energy West Mining Co. at the Deer Creek and Cottonwood Mines, near Orangeville, UT. The USBM evaluated hydrologic and overburden failure data to assess the response of local ground water to underground coal mining in single-and multiple-seam conditions. Fourteen springs located over the two mines were investigated in the study along with overburden failure response caused by longwall panel extraction. Spring discharge was compared to climatic variation and time of undermining to quantify response to undermining. Spring discharge had been reduced owing to below-normal precipitation during the period evaluated. The response of springs to mining in the vicinity was influenced in part by the thick overburden present at the study site the presence of hydrophilic clays and mudstones in the overburden stratigraphy, and elevation of the springs above mine level, which buffered the effects of undermining.

Jan 1, 1994

By MINE SAFETY BOARD

Mining men and State officials in their efforts to make mining safer are confronted from time to time with various complicated questions . In recent years these questions have tended to increase with the use of mechanical appliances . Twenty- five years ago electricity had hardly been used in mines . To - day there is practically no other means of transmitting energy employed in American mines , except in metal mines where compressed air is used for drilling and small portable hoists . In coal mines there has been a great increase in mechanization and a tendency to concentrate the mining operation , which has resulted in attendant difficulties of ventilation and intensified the danger of coal - dust in bituminous and subbituminous mines . The answers to the questions which arise are not always obvious , as is shown by the fact that even able , experienced men differ in their opinions of the best way to overcome a particular mining hazard . The difficulty of solving the problems is also demonstrated by the varying provisions in mine safety rules , both in official regulations and in the rules of those mining companies who are endeavoring to do more than follow the letter of the law . Such differences of opinion on the best way of meeting a difficult situation are often found within the same mining organization , and so it has been in the Bureau of Mines .

Nov 1, 1929

By J. B. Janus

This report, the 22d in a series, gives analytical data showing composition and quality of tipple and delivered samples of coal collected during fiscal year 1972. This coverage lists mines located in 20 States. Ultimate analyses are given for most of the coalbeds listed. Tipple samples were collected by Bureau of Mines engineers at tipples as coal was being loaded into railroad cars or trucks. The deliveries were sampled in accordance with instructions issued by the Bureau of Mines, and the samples were analyzed in the Bureau laboratory at Pittsburgh.

Jan 1, 1973

By Susan M. Moore

According to the Mine Safety and Health Administration (MSHA) injury database, 227 knee injuries were reported in underground coal mining in 2007 [ 1]. Low-seam coal mines are those with extremely low working heights (<42?). Gallagher et. al [2] found that the average cost per knee injury in low-seam coal operations was $13,121.29. Thus, it can be estimated that the financial burden of knee injuries was nearly three million dollars in 2007. Pressure applied to the knee while kneeling and crawling is likely a risk factor. Typically, mine workers utilize kneepads to better distribute the pressures at the knee; however, their ability to reduce the stresses at the knee is unknown. The objective of this study was to determine the pressure applied to the knee during static postures used in low-seam mining while not wearing kneepads and while wearing two kneepads commonly used in the industry (one articulated and one non-articulated).

Jan 1, 2009

By H. Polat, Q. Hu, S. Chander

"The collection efficiency of dust particles was determined in a laboratory dust chamber equipped with a water spray. Measurements were made in the presence of selected nonionic, cationic and anionic surfactants. For the nonionic and the anionic reagents, efficiency was maximum in a narrow range of concentration. The surfactant concentration corresponding to high collection efficiency was usually much below the commonly used concentration of l "", however. In comparison, much higher collection efficiency was observed for a cationic surfactant at extremely low concentrations. For delineating the mechanism of capture of dust particles, surface tension and contact angle results were used to obtain a correlation between the work of adhesion and the efficiency of collection. Such a correlation was reasonable for the nonionic surfactants but not for charged surfactants. In the latter case, electrostatic interactions between charged droplets and particles were more important, especially for the cationic reagent. INTRODUCTIONSeveral methods are used to control dust in mines. These include: ventilation, foam, scrubbers and sprays. This article is concerned with improving the effectiveness of water sprays, which are widely used to remove dust particles during continuous mining, by adding small quantities of surfactants. Water sprays produce small droplets which act as collectors of dust particles suspended in air. Sprays directed at the actual source of dust have the additional property of wetting the coal before the ·particles become airborne (Hamilton, 1974). Wetting agents, also called surfactants, arc known to play an important role in many applications where dust is a problem. However, conflicting reports exist in the literature with regard to the effectiveness of surfactants in water sprays (for a review, see Chander et al., 1988). In spite of the conflicting reports, the use of surfactants for dust control has increased over the years. In a recent study by the Bureau of Mines, a 27'6 reduction in respirable dust levels was observed in a mine test when surfactants were added to sprays (Foley, 1991)."

Mar 1, 1992

By Webster S. Anderson

Bureau of Mines planer mining tests on the phosphate bed of the Douglas mine, near Drummond, Mont., indicated that a competent bed with a Mohs&apos; scale hardness of 3 to 4 cannot be mined economically with the planer. Although planer mining was feasible where the bed was fractured enough for a 4-inch depth of cut to be consistently maintained, the depth of cut in the competent beds at the Douglas mine did not exceed 0.5 inch. Average production rates were 0.15 ton per minute and 9 tons per man-shift.

Jan 1, 1966

By T. F. Tomb

Past experience has shown that the penetration characteristics of the 10-mm nylon cyclone used on approved personal sampling equipment are significantly different from those determined in the laboratory using a nonpulsating flow source. The Bureau of Mines has developed and recommended a modification to presently approved equipment that will alleviate this difference. However, as a result of this modification, a new relationship for converting respirable dust concentrations measured with approved personal sampling equipment to equivalent concentrations as measured with an MRE instrument will have to be established. This Bureau of Mines report describes the underground sampling program conducted to establish a new factor for converting respirable dust concentrations measured with personal sampling equipment, modified with a recommended pulsation damping device, to an equivalent concentration as measured with an MRE gravimetric dust sampler.

Jan 1, 1973

By John R. Troxell

"INTRODUCTION Lookout Mountain is the natural barmier that isolates Dade County from the rest of Georgia. Legend has it that Dade County seceded from the Union long before the rest of the State of Georgia and did not officially return until July 4, 1945.Coal mining began in the Lookout Mountain area in 1891, and by 1894 production amounted to about 1,000 tons daily. Present production by the two principal operating companies is about 3,600 tons monthly.In the Sand Mountain area, coal has been mined intermittently since before the Civil War, and probably 6,500,000 tons has been produced.The Bureau of Mines coal project was initiated to alleviate a possible coal shortage and to assist the State in developing coal deposits to supply State institutions and local markets. Drilling began January 1, 1945, and ended May 11, 1945, after 2,907 feet had been drilled. By this time the Georgia Power Co. became interested in northwest Georgia coal fields as a possible source of more economic fuel for their steam-driven power plants, but the Bureau continued to act in an advisory capacity to the power company until June 30, 1945."

Oct 1, 1946

By Jr. Sillers

This is the sixth report of investigations in cooperation with the steel industry to establish the technological acceptability of electrolytic manganese in steelmaking processes. The bulk of the .electrolytic manganese used in these tests was produced by the Bureau Of Mines from domestic ores at its Boulder City, Nev., pilot plant by the process developed by the Bureau. Electrolytic manganese for the first series of tests made in 1940 was supplied by the Electro manganese Corp., Knoxville, Tenn. The first report dealt with the application of electrolytic manganese to the manufacture of stainless.steel;9 the second with tests in acid electric and acid open-hearth low and medium carbon-steel castings; the third with its use in rimmed and? killed low-carbon steels; the fourth with its application to the manufacture of stainless steel as well as the Timken 16-25-6 alloy for gas turbines; and the fifth with tests in acid and basic electric steel foundry practice and basic steel ingot production.

Jan 1, 1948

By W. M. Deaton

The Keyes Helium Plant of the Federal Bureau of Mines was constructed under an expedited schedule, to supply the urgent and growing demand for helium in atomic energy, missiles, aerology, space exploration, shielded-arc welding, and low-temperature research. Construction began in December 1958 and ended in August 1959. The plant, near Keyes, Okla., processes 2 percent helium-bearing natural gas from the Keyes gasfield. In 1960 the plant produced and shipped 263 million cubic feet of helium (equivalent to an annual rate of 290 million cubic feet). Production cost was $9.11 a thousand cubic feet of helium. A low-temperature process involving two steps is used; the first separates a crude-helium product from the natural gas at about -250° F. and 225 pounds per square inch gage (p.s.i.g.); and the second purifies the crude helium to a high-purity product (Grade-A helium, 99.995 percent helium) at about -320° F. and 2,750 p.s.i.g.

Jan 1, 1961

By B. D. Nash

The Bureau of Mines continued its research into the recovery of fluorine by the phosphoric acid acidulation defluorination of phosphate rock concentrates. A small process development unit with a capacity of about 10 kilo-grams of charge per hour was operated, and concentrates from both Idaho and Florida were processed. Over 80 percent of the fluorine was evolved and recovered as a dilute fluosilicic acid solution. Phosphate extraction from the concentrates always exceeded 98 percent. The fluorine was converted to a synthetic fluorspar product (3CaFa?SiOa) suitable for use as a slag conditioner in electric furnace steelmaking operations.

Jan 1, 1977

By K. K. Kershner

Nickel having a purity of more than 99.99 percent with reference to metallic impurities was electrodeposited at the Rolla Metallurgy Research Center of the Federal Bureau of Mines. The production of high-purity nickel is in keeping with the current trend in technologies for producing metals with lower and lower percentages of impurities. To understand more fully the role to be played by nickel by itself and as a component in many alloys, the element must be in a state of high purity. Procedures are outlined for purifying nickel solutions by precipitating and filtering off impurities. Details are given for using the purified solutions as electrolytes in depositing high-purity nickel. The elecneleposited nickel contained 0.0005 to 0.002 percent each of cobalt, copper, aid iron together with spectrographically detectable traces of aluminum, magnesium, and silicon. The deposits were smooth and dense; the crystalline structure was typical of an electrodeposited metal. Some preliminary experiments for purifying nickel solutions by liquid-liquid extraction are also described in this report. Tests of this type were limited since more encouraging results were obtained by other methods of purification.

Jan 1, 1961

By L. Y. Sadler

The Bureau of Mines conducted a study Lo determine the loss in weight of silica (Si02) volatilization from low-alumina (A1203) refractories used as hot face liner materials in such process equipment as coal gasifiers, synthesis gas transfer lines, and ammonia plant secondary re-formers. Small specimens of 80-and 40-pct-A1203 brick and 95-pct-SiO2 brick were exposed to steam in high-pressure furnaces at pressures of up to 1,000 psig and temperatures up to 1,400° C for periods ranging up to 120 h. Weight losses from the 40-pct-A1203 brick after 40 h of exposure were highest, 2.75 pet at 1,400° C and 1,000 psig. The rate of weight loss had dropped to near zero after 80 h of exposure at all temperatures. No relationship between total silica content of the specimen and weight loss could be established nor did scanning electron microscopic examination of the specimens before and after exposure identify specific regions (e.g., surface) suffering a disproportionate share of the silica loss. It was concluded that minor silica volatilization is likely to occur, if at all, at temperatures of less than 1,000° C and pressures below 1,000 psig, and that low-alumina refractories should be used as dry-ash coal gasifier hot face linings.

Jan 1, 1986

By J. Bruce Clemmer

[Gypsum is one of the mo .. t iJf.l)ortant nonmp.tal1.ic T!1inerals, as is indicat-? ed by the fact that tlle Uni ted states cO!1sUl:Ied p, roximn..tely 3,500,000 tons of natura.l and calcinecl e::,j;-psum in 1937. The b\.&apos;.ilr:.in.; traces \"fe.ro the largest users and required 2,520,000 tons of calcine for the r-roductiop. of plaster,]

Jan 1, 1941

By J. S. Browning

Laboratory and pilot-plant tests of spodumene-beryl pegmatites of the Kings Mountain, N. C., area resulted in development of a new and improved method by the Bureau of Mines for separating and recovering spodumene, mica, and beryl. The process was successfully applied to other domestic pegmatites and a spodumene flotation-plant tailing containing about 0.5 percent beryl. The method comprised soap flotation of the spodumene, using combinations of sodium fluoride and lignin sulfonate as conditioning agents to recover 80 to 85 percent of the contained lithia in concentrates assaying over 6 percent Li20. About 80 percent or more of the beryl was retarded in the spodumene tailing. The beryl subsequently was activated, floated, and cleaned in a secondary circuit to yield beryl concentrates containing 6 to 7 percent BeO. The tests also demonstrated that a good recovery of high-grade mica could be produced.

Jan 1, 1961

By Albert E. Schreck

[THE COMPOUNDS of strontium were confused with those of barium until 1790, when A. Crawford discovered that the mineral strontianite, long believed to be a barium mineral, was a compound of a new element. This discovery was confirmed 2 years later by I. C. Hope. The mineral was named strontianite because it was found near the town of Strontian in Argyllshire, Scotland. In 1808 Sir Humphrey Davy isolated strontium metal by the electrolysis of fused chlorides. Celestite (strontium sulfate) and strontianite (strontium carbonate) are the principal strontium minerals. Because of its more widespread occurrence, celestite is more important commercially.]

Jan 1, 1959