Search Documents

By Thomas H. Dubaniewicz

The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, conducted a study of past mine explosions to identify the ignition locations and ignition sources responsible for the most severe explosion events resulting in death. Since the Scotia disaster of 1976, many fatalities from underground coal mine explosions have been linked to nonpermissible electrical equipment ignition sources located in intake air courses. With few exceptions, explosion protected equipment is generally not required in intake air courses of gassy underground coal mines in the US. Cigarette lighters were another prevalent ignition source for fatal explosions ignited in intake air courses. Several mine rescue/ recovery teams have encountered electrical ignition hazards. The study provides evidence that intake air courses of gassy underground coal mines fit the description of certain Hazardous (classified) locations described in the US National Electrical Code®. Class I Division 2 or Zone 2 explosion protection tech¬niques may be used to design intake air equipment so that it does not present an ignition source under normal operation, before mine power is shut down in emergency situations. Nonpermissible circuits in intake air courses that are likely to remain energized during emergencies, e.g. battery powered equipment, should be protected by more stringent Class I Division 1, Zone 1, or Zone 0 techniques, to protect rescue/recovery personnel.

Jan 1, 2009

By M. R. Geer

Traditionally, fine coal is more troublesome than the coarser sizes at every step of the coal-preparation process--screening, cleaning, dewatering, and drying. Therefore the present trend toward a higher proportion of fines in the run-of-mine product, brought about by changes in mining practice necessitated to increase productivity, has added greatly to the task of preparing coal for the market. One of the more difficult and costly problems involved is that of recovering fine solids from the washery water. These fine solids should be recovered in the interest of conservation, and they must be removed to provide recirculating water of proper quality. If there is a plant effluent, it must meet increasingly stringent requirements against stream pollution. Vacuum filtration has been used for years at a few plants to recover the extreme fines, but its additional cost discouraged general adoption until recently. Now, with growing emphasis on better solids recovery, filtration is becoming more widespread. Many coal slurries filter readily, giving high cake rates and clean filtrates. Others, however, particularly those containing either a high proportion of material finer than 200-mesh or an appreciable amount of clay, are much more difficult to filter. Many of these refractory slurries can be rendered more filterable by flocculation. A previous report of Bureau of Mines research dealing with flocculation alone was published in 1940.5/

Jan 1, 1959

By Harry D. Jumper

This paper describing the methods of ruining a sand, gravel, and bowlder deposit 20 miles east of Los Angeles, and the classification and preparation of these materials for market, is one of a series being prepared for and published by the United States Bureau of Mines on methods and cost of mining sand and gravel. These papers are designed to disseminate technical information regarding, the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion anti study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations stall ensue. The description contained herein is typical of this industry in Southern California. ACKNOWLEDGMENT The author acknowledges tine assistance of L. L. Rogers, vice-president and manager of production and distribution for the Consolidated Rock Products Co., in the preparation of this paper.

Jan 1, 1933

By H. Kenworthy

[Experimental studies were made to develop a laboratory technique for direct removal of cadmium and germanium from sphalerite concentrates. Cadmium- and germanium-bearing concentrates from the Illinois-Kentucky fluorspar field were sound to be, amenable to an inert atmosphere fuming process for removing these two moats in the form of gaseous sulfides. Treating the condensed fume by pyrometallurgical methods upgraded the material end provided a means of partly separating the constituents. Cadmium was concentrated about 35:1 arid germanium about 300:1. The extractive investigations were supplemented by vapor-pressure studies on the sulfides of germanium to obtain fundamental data for larger scale laboratory conditioning and control when treating the zinc concentrates. Vapor-pressure curves were developed for synthesized monosulfide and disulfide The results of these- investigations indicate the possibility of significantly increasing the recovery of cadmium from zinc concentrates. Comparison with present recovery of germanium cannot be made, since commercial recovery data arc not available.]

Jan 1, 1956

By Robert C. Bates

This Bureau of Mines report converts published data on the cost of ventilating uranium mines to a common price base and analyzes these data to determine the cost per ton of uranium ore at various levels of radiation exposure control. There appears to be an exponential increase of cost as the radiation level is lowered. The 1967 base costs are extrapolated to present dollars, and some cost comparisons are given for other radiation control measures.

Jan 1, 1981

By David E. Siskind

The Bureau of Mines recorded particle accelerations in the mine roof produced by three types of explosives in the Pilot Knob Pellet Co. mine, Pilot Knob, Mo. Examined were the effectiveness of cube root, square root, and two-thirds power scaling in grouping the underground blast vibration data, and the effects of mine geometry, rock type, explosive type, and charge size on blast vibration levels. A propagation law for this mine was determined. The scaling factor of the square root of the charge weight was developed from previous Bureau studies of vibrations from quarry blasts, and in under-ground blasting both square root and cube root scaling were found applicable for scaling particle vibration data. The vibrations from the Pilot Knob blasts were best grouped by a square-root scaling factor. The empirical propagation equation AW1/2 = 76,250 (R/W1/2)-2.61 where A is the peak acceleration in g's, W is the charge weight in pounds, and R is the distance from the blast in feet, may be used to describe vibration amplitudes from charges fired with zero delay caps or with a single cap at Pilot Knob. Statistically significant differences were found in the vibration levels generated by the different explosives. The Power Primer (75-percent weight-strength ammonia gelatin dynamite) produced levels of vibration of 1.7 to 2.4 times those of AN-FO and slurry explosives; the latter two are approximately equal.

Jan 1, 1973

By J. B. Gayle

Many investigators have reported studies of size distributions for particulate solids ; usually , these have involved the fitting of size distribution data to a particular mathematical function . Such studies are of unquestioned value and have contributed much worthwhile information regarding the breakage mechanisms for a variety of brittle materials . In connection with a Bureau of Mines study of the size distribution of coke , which has been subjected to the standard American Society for Testing Materials (ASTM) tumbler test , attention was focused on the relation between the 1 -inch tumbler index (usually considered to be indicative of the ability of coke to resist degradation by impact ) and the 1 /4 - inch tumbler index ( indicative of the ability to resist degradation by abrasion ) . Specifically , it was noted that for certain sets of data the correlation coefficients denoting the relation between these indexes were positive ; for other sets of data , these coefficients were negative . Preliminary consideration of this problem indicated that the usual interpretation placed on correlation coefficients was erroneous in this particular instance because the variables being correlated were necessarily related . The work described in this report was undertaken to clarify the interpretation of results of correlation studies for variables of this type .

Jul 1, 1960

By Larry D. Nichols

Poroplastic membranes containing ion exchange liquids were studied for separating cobalt from nickel-containing solutions similar to ammoniacal laterite leaches. The driving force for cobalt transport was differences in pH and composition between the leach and extraction streams. Using a diketone ion exchange liquid, a leach pH of 6.5 to 7.0, and a strip pH of 2.3, cobalt was extracted from a 750 ppm solution containing 2500 ppm of nickel at rates ranging from 1 to 10 µg/cm2 .min in single membrane cells, and from 10 to 100 in more closely spaced multiple membrane cells. Rates were variable, with evidence that cross -membrane flow pasterns were a key factor; a reproducible rate of 30 pg/cm .min would be economically viable. Loss of transport observed after several days of continuous operation was restored by flushing membranes with fresh ion exchange liquid. A major effort was devoted to preparation of thin, leak-free membranes; the resulting membranes endured operating conditions without mechanical failure.

Jan 1, 1982

By Thomas M. Nasiatka

Tests with a high-pressure water jet were conducted in the steeply pitching Roslyn No. 5 bituminous coalbed in the Roslyn No. 9 mine, Roslyn, Wash., to determine the feasibility of extracting coal from pillars and from a solid coal face in development without drilling and blasting. During pillar mining, using a hand-held monitor, the best results were obtained with a 0.150-inch- diameter nozzle, a water pressure of 3,500 psi, and a flow rate of 38.5 gpm.3 The rate of mining and productivity were 0.74 ton per minute and 16.6 tons per man-shift, respectively. During development mining, using a monitor mounted on a roof jack, the best results were obtained with a 0.148-inch-diameter nozzle, a water pressure of 4,500 psi, and a flow rate of 40.0 gpm. In one section of the mine where the coal was relatively hard, the rate .of mining and productivity were 0.10 ton per minute and 5.7 tons per man-shift, respectively in another section of the mine where the coal was relatively soft, the rate of mining and productivity were 0.51 ton per minute and 8.3 tons per man-shift, respectively. The tests showed that hydraulic mining methods were more productive than conventional mining methods in pillar mining. In development the productivity of hydraulic mining depended primarily upon the coal hardness. Compared with conventional methods, hydraulic mining methods were less productive where the coal was relatively hard and equally as productive where the coal was relatively soft.

Jan 1, 1963

By P. M. Gruzensky

A survey of the literature has been made covering the extraction of bismuth from raw materials, its separation from lead, and its subsequent refining. The use of aqueous, nonaqueous, and fused electrolytes in electrolytic refining is reviewed. This literature survey has been prepared preliminary to some proposed investigations concerning the electrometallurgy of bismuth, and, although an effort has been made to cover a majority of the applicable references, a critical review was not attempted and no assertion is made that this manuscript is exhaustive in nature. Titles of publications in parenthesis are translations from the language in which the reference was originally published.

Jan 1, 1954

By Peter N. Gabby

In 1990, the Bureau of Mines conducted a mineral resource investigation of the 12.321 acre Black Warrior study area, one of several proposed additions to the Sawtooth Wilderness. No identified mineral resources were delineated. There were 123 lode and placer claims in or adjacent to the study area. There is a known hot spring adjacent to the study area, but presently no geothermal leases are pending. Lode mines in pr adjacent to the Black Warrior study area have produced 4,022 tons of ore from which 1,981 oz of gold and 811 oz of silver were recovered. None of the vines are currently active. During the field study 125 rock samples were taken. Significant gold assays and favorable geologic characteristics at seven properties indicate that gold occurrences and resources with byproduct metals may exist in the study area. Two other sites yielded anomalous gold assays; however, sage favorable geologic characteristics are lacking. Presently, identified gold resources are being delineated by drilling programs in the nearby Atlanta and Rocky Bar mining districts. These districts have geologic characteristics similar to the Black Warrior area. During the field study 22 placer samples were taken. In most places where an anomalous concentration of gold was found, the stream channels are too narrow for operations other than recreational suction dredges. However. One area is estimated to contain over 2 million yd3 of gold-bearing gravels.

Jan 1, 1992

By Charles Will Wright

The purpose of this paper is to present briefly certain preliminary results of the study of mining methods by the United States Bureau of Mines; to show the relative importance of each method in terms of tonnages mined and man-hours consumed; to give to the mining engineers and particularly to the young student of mining a better understanding of the principal mining methods; and to indicate changes now in progress and to present suggestions for improvements in the art of mining. Questions of mine development and details of underground practice such as drilling and blasting, loading, hauling, hoisting, ventilating, pay systems and mine management are omitted, as these have been or will be discussed in other bureau publications.

Jan 1, 1931

By D. W. Scott

Thermodynamics is a powerful tool for investigating rotational isomerism in substituted ethanes and related molecules. Accurate calorimetric data can be interpreted to give information, not only about the energy difference between conformations, but also about the shape of the potential barrier hindering rotation from one conformation to another. However, a deterrent to this use of thermodynamics is the labor required to calculate the contributions to the thermodynamic functions for assumed potential functions. Tables of thermo-dynamic contributions for appropriate potential functions can eliminate that labor and greatly facilitate the thermodynamic study of rotational isomerism. In this research, tables of contributions to the thermodynamic functions were compiled for two potential functions typical of some commonly encountered examples of rotational isomerism. TYPES OF POTENTIAL FUNCTIONS Potential function 1, illustrated in figure 1, A, has two equal minima higher than the third. It has the general shape of the barrier to internal rotation in n-butane, for example. The trans conformation of n-butane has the lowest energy, and the two skew or gauche conformations have equal but higher energy. Potential function2, illustrated in figure 1, B, has two equal minima lower than the third. It has the general shape of the barrier in 2-methylbutane, for example. The two C1 conformations of 2-methylbutane have equal energy much lower than the assumed Cs conformation, which has not been observed spectroscopically.

Jan 1, 1962

By R. V. Ramani, R. A. Jankowski, R. Bhaskar

"The spatial distribution of airborne dusts, deposition of dust in the airway, as well as the effect of airflow velocity and particle density on dust behavior in mine airways were studied in a set of experiments performed in a mine airway under controlled conditions. Considerable deposition of dust near the source was indicated. Pronounced effects due to velocity were observed in ambient dust concentration and deposition along the mine airway, both in the respirable and the total size ranges. Cross-sectional concentration measurements indicate an increase in concentration from the roof to the floor. The average cross-sectional concentration is about 75% of the concentration in the center of the airway.IntroductionA number of studies have been performed since the early 1950s on the behavior of dust in mine air (Bradshaw and Godbert, 1954; Dawes and Slack, 1954; Bradshaw et al., 1954; Hall, 1955-56; Reinhardt, 1971; Ford, 1971; Courtney et al., 1982). While the experimental data available from these studies are indeed useful in understanding dust cloud behavior in a specific situation, no generalized conclusions can be drawn because of the lack of data on parameters such as flow velocity, size distribution of the source dust, and particle density. These change from mine to mine or even within the same mine. The present study is aimed at providing a better understanding of the temporal and spatial behavior of dust particles in underground' mine airways (National Academy of Sciences, 1980). The characteristics studied encompassed airborne concentrations and floor depositions over the entire size range as well as the respirable size range. The experimental results in this paper are intended to complement a mathematical model developed to predict ambient concentration and deposition of airborne dust in mine airways (Bhaskar and Ramani, 1986)."

Aug 31, 1989

By Erich K. Bender

This report summarizes work performed under Phase I of USBM Contract No. H0366024, Noise Reduction of Jumbo Mounted Percussive Drills. Four drills -Gardner-Denver D93LAR and DH123 and Ingersoll-Rand 0475 and VL120 models were measured at the two manufacturers? test sites; data are given in terms of characteristic noise and vibration levels. A survey of percussive rock drill users is reported. The rationale for the choice of a demonstration drill, the Gardner-Denver DH123, is given and a desired noise reduction goal is established.

Jan 1, 1976

By W. D. Ludemann, E. A. Loria, E. A. Rowe

The isothermal recrystallization of electrorefined vanadium has been studied as a function of annealing time , temperature , and prior deformation . Specimens were cold- rolled from 30- to 75 - percent reduction in thickness , then annealed from 700 ° to 1,200 ° C at time periods ranging from 1 minute to 96 hours . The course of recrystallization was followed by means of hardness , metallographic , and X- ray techniques , and a recrystallization diagram was constructed . Interpretation of the data indicated that there was around 50- percent softening due to recovery ( first stage of softening) before recrystallization began . The defining of recrystallization limits with respect to the amount of deformation was precisely established for electrorefined vanadium . More than 30- percent reduction was necessary for recrystallization to occur at 850 ° C. With 60- percent reduction , it was initiated at 750 ° C and completed at 950° C. The activation energy for recrystallization , as derived from the data , was 95,300 cal per mole for 60 - percent reduction and annealing at 750 ° to 900 ° C. Recrystallization by the mechanism of nucleation and growth was the principal process during the second stage of softening . minor part of the second stage of softening took place as strain- induced boundary migration , which was observed in specimens reduced 30 percent , bent in L- shape , and annealed at 950 ° C. Grain size decreased significantly only with the largest reductions and annealing between 750 ° and 950 ° C. Grain growth was expressed by the empirical relation D = KKtt"" ,, the exponent being the same at 60- percent reduction and annealing from 750 ° to 900 ° C. Accordingly , the activation energy for grain growth was 75,000 cal per mole .

Jan 1, 1964

By Thomas Varley

[For a year or more, statements have appeared in the technical press, and Especially in various trade journals, indicating that valuable metals such as gold, silver, platinum, and other rare metals, have been found and also have been successfully extracted from oil shales. These reports stated tat decarbonization and special methods of chlorination treatment, leaching and subsequent Precipitation, also cyanidation followed by table concentration of the residues after cyanidation, all indicated that told ad silver and other metals could be, and were, successfully recovered. Such articles have caused much misunderstanding, and as the correctness of some re of the statements made in them were questioned by some of the technical journals and by various chemists and metallurgists, an investigation of the subject. was begun by the metallurgical division of the Bureau of Mines, in order, if possible, to determine to what extent, if any, metals of value do occur in oil shales, and if so, the feasibility of attempting their recovery by tie processes said to have been used for teat Purpose. Inasmuch as the Bureau's station at Salt Lake City is investigating the recovery of oil from oil shales, the investigation of too recovery of metals from oil shales was assigned to my direction as superintendent 'of that station. An agreement had been entered into with the owner of m extensive oil shale deposit in Wyoming whereby I would personally collect the samples' of shales for use in the investigation.]

Jan 1, 1922

By Mah Alla D.

Previously existing heat-of-formation values for the oxides of vanadium were rudimentary. They were subject to uncertainties of 1 to 5 kilocalories per gram-atom of contained oxygen. This fact has been the only adverse influence on the accuracy of thermodynamic calculations involving these substances, as the requisite entropy and high-temperature heat-content data are known with reasonable accuracy. This report presents new heat-of-formation data for four oxides of vanadium (VO, V203, V02, and V205), obtained by combustion calorimetry. It is believed that the uncertainties have been reduced to 0.1 to 0.3 kilocalorie per gram-atom of contained oxygen. The new heat-of-formation data were combined with existing entropy and high-temperature heat-content values to obtain free energies of formation of the four oxides at temperatures up to 2,000° K.

Jan 1, 1961

By E. D. Gardner

This paper discusses prospecting for lode gold and lists the principal lags and. regulations pertaining to locating; lode claims on public lands. It is a preprint of a part of a bulletin being prepared by the United States Bureau o Mines entitled "Equipping, Developing and Operating Small Gold Mines". The increased interest in gold mining manifested during the past few years (1932-1935) bas stimulated prospecting. Many adventurers have taken to the field to search for now gold deposits. A. large percentage of them have had no previous experience in prospecting for lode gold; this paper has been written with the tope that it might assist these newcomers.

Jan 1, 1935

By H. C. Miller

The removal of the mud sheaths that are deposited against the faces of productive oil sands during rotary drilling is one of the important problems confronting operators, especially in semidepleted fields where formation pressures are low. Unless the mud sheaths behind the perforated oil strings and liners are removed and the sands exposed, oil cannot enter the wells. Consequently much oil that otherwise might be produced from low-pressure sands is trapped and never recovered. Various types of perforation washers, down swabs, and agitators are used at present for breaking down the mud sheaths and removing the disintegrated clay particles from wells after the perforated Wipes have been inserted. Mechanical methods for removing mud sheaths are :quite satisfactory, but prompted by the request of certain .operators in the California oil fields Bureau of Mines engineers have conducted a series of laboratory tests with the view of developing a chemical method for removing mud sheaths in oil wells that will be applicable to field conditions. This report describes the laboratory work and deals generally with a chemical method for removing the mud sheath, cake, or plaster deposited against the face of oil sands in drilling wells end in wells that, on being shut in temporarily during periods of overproduction of oil, are conditioned for the shutdown .period by filling the well opposite the producing formations with mud fluid. The method described in this report was devised in the San Francisco laboratory of the Bureau of Mines and, as far as the writers have been able to determine, differs from any chemical method ever used in actual wells. The method proposes to add a small amount of calcium carbonate (preferably pulverized limestone) to the mud fluids before they are introduced into the wells so that the resultant mud sheaths will be susceptible to disintegration by acid solutions when it is desired to expose the faces of the oil sands in the wells.

Jan 1, 1934